Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Overview KEMET’s 900 series encapsulated radial leaded ceramic disc capacitors are specifically designed for interferencesuppression AC line filtering applications. Having internationally recognized safety certifications, these capacitors are well-suited for applications that require keeping potentially disruptive or damaging line transients and EMI out of susceptible equipment. They are also an ideal solution when needing to suppress line disturbances at the source. With a working voltage of 760 VAC in line-to-line (Class X)and 500 VAC in line-to-ground (Class Y) applications, these safety capacitors meet the impulse test criteria outlined in IEC Standard 60384. Meeting subclass X1 and Y1 requirements, these devices are certified to withstand impulses up to 4 KV (X1) and 8 KV (Y1) respectively. These encapsulated devices also meet the flame test requirements outlined in UL Standard 94V-0. Safety Certified Capacitors are classified as either X and/or Y capacitors. Class X capacitors are primarily used in line-to line (across-the-line) applications. In this application there is no danger of electric shock to humans should the capacitor fail, but could result in a risk of fire. The class Y capacitor is primarily used in line-to-ground (line by-pass) applications. In this application, failure of the capacitor could lead to danger of electric shock. Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Ordering Information 1 C9 6 1 U Ceramic Series Body Diameter Lead Spacing1 Spec. C9 = Ceramic 900 Series 1 = 8.0 mm 2 = 9.0 mm 3 = 10.0 mm 5 = 12.0 mm 6 = 13.0 mm 7 = 14.0 mm 8 = 15.0 mm 1 = 10.0 mm U= Safety 222 M Capacitance Capacitance Code (pF) Tolerance 2 significant digits + number of zeroes M = ±20% W Rated Voltage W = X1 760 VAC /Y1 500 VAC W D Dielectric/ Design Temp. Char. W = Y5U D= Disc A A 7317 Lead Config.1 Failure Rate Packaging (C-Spec) A = N/A See "Packaging C-Spec Ordering Options Table" below A= Straight B= Vertical Kink C= Outside Kink "Vertical Kink" and "Outside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is only available on capacitors ordered with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET. One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 1 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Packaging C-Spec Ordering Options Table Packaging Type Lead Length (mm)2,3 Packaging Ordering Code (C-Spec) Ammo Pack 20.0 +1.5/-1.0 (straight leads) 18.0 +2.0/-0 (preformed leads1) 7317 Bulk Bag 3.0 ±1.0 3.5 ±1.0 4.0 ±1.0 4.5 ±1.0 5.0 ±1.0 20.0 minimum4 WL30 WL35 WL40 WL45 WL50 WL20 Preformed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 "Vertical Kink", "Outside Kink" and "Inside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is only available on capacitors with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET. 3 Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to verify availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET. 4 Lead length of 20.0 mm minimum only available for straight leads. 1 Benefits • • • • • • • • • • • • Safety Standard Recognized (IEC 60384–14) Reliable operation up to 125°C Class X1/Y1 10 mm lead spacing Lead (Pb)-free and RoHS Compliant Halogen Free Available capacitance tolerances of ±5%, ±10%, and ±20% High reliability Preformed (crimped) or straight lead configurations Non-polar device, minimizing installation concerns 100% pure matte tin-plated lead finish allowing for excellent solderability Encapsulation meets flammability standard UL 94V–0 Applications Typical applications include: • Line-to-line (Class X) filtering • Line-to-ground (Class Y) filtering • Antenna coupling • Primary and secondary coupling (switching power supplies) • Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 2 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Lead Configurations Straight Vertical Kink T D Outside Kink T D T D 3.0 Maximum 3.0 Maximum 3.0 Maximum 4.0 Maximum LL LL F F 5.0 Maximum LL F S S S Dimensions – Millimeters F Lead Configuration Lead Configuration Ordering Code1 Lead Spacing2 Lead Spacing Tolerance Straight A 10.0 ±1.0 Vertical Kink (Preformed) B 10.0 ±1.0 Outside Kink (Preformed) C 10.0 ±1.0 D T e Ød Body Diameter2 Body Thickness Lead Meniscus Lead Diameter 3.0 maximum 0.55 ±0.1 See Table 1 "Product Ordering Codes and Ratings" Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for further details. 2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for further details. 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 3 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Approval Standard and Certification No. Safety Standard Standard No. VDE (ENEC) IEC 60384–14 Subclass Working Voltage X1 760 VAC Y1 500 VAC Certificate No. 40034867 These devices are VDE/ENEC recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14. Environmental Compliance These devices are Halogen Free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives. General Specifications/Performance Characteristics Dielectric/Temperature Characteristic Y5P Operating Temperature Range: Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC): Y5U -40°C to +125°C ±10% +20%/-55% Dielectric Withstanding Voltage 4,000 VAC (60 ±5 seconds at 25ºC) Quality Factor (Q) See “Dissipation Factor” Dissipation Factor (tanδ) at +25ºC1 Insulation Resistance (IR) Limit at +25°C 2.50% 2.50% 10,000 MΩ Minimum (500 VDC applied for 60 ±5 seconds @ 25°C) Capacitance and Dissipation Factor (DF) measured under the following conditions: 1 kHz ±50 Hz and 1.0 ±0.2 Vrms Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 4 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Table 1 – Product Ordering Codes and Ratings Dielectric/ Temp. Char. Y5P Y5U Dimensions (mm) KEMET Part Number Capacitance Capacitance Tolerance C911U101KWYD(1)A(2) 100 pF 8.0 8.0 Body Body Lead Diameter Thickness Diameter (Maximum) (Maximum) C911U151KWYD(1)A(2) 150 pF C911U221KWYD(1)A(2) 220 pF 8.0 C911U331KWYD(1)A(2) 330 pF 8.0 C921U471KWYD(1)A(2) 470 pF C931U561KWYD(1)A(2) 560 pF 10.0 C931U681KWYD(1)A(2) 680 pF 10.0 C951U102KWYD(1)A(2) 1,000 pF 12.0 C921U102MWWD(1)A(2) 1,000 pF 9.0 10.0 ±10% Bulk Packaging Ammo Packaging 9.0 C931U152MWWD(1)A(2) 1,500 pF C961U222MWWD(1)A(2) 2,200 pF C961U332MWWD(1)A(2) 3,300 pF C971U392MWWD(1)A(2) 3,900 pF 14.0 C981U472MWWD(1)A(2) 4,700 pF 15.0 ±20% Lead Spacing 7.0 0.55 ±0.05 10 mm 13.0 13.0 (1) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = Straight B = Vertical Kink C = Outside Kink (2) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code". See "Dimensions" section of this document, page 2, for available options. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 5 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions Item Specification -40ºC to +125ºC Operating Temperature Range Dielectric Strength Between lead wires No failures Body Insulation No failures Insulation Resistance (IR) 10,000 MΩ minimum Capacitance Within specified tolerance Dissipation Factor (DF) or Q DF ≤ 2.5% Temperature Characteristics Y5U Capacitance Change Within +22% / -56% Temperature Characteristics Tensile Lead wire or capacitor body shall not break. Bending Lead wire or capacitor body shall not break. Terminal Strength Solderability 1 Test Method Lead wire should have a uniform coating of solder in the axial direction and over 3/4 of its circumference. The capacitor shall not be damaged when 4,000 VAC(rms) is applied between the lead wires for 60 seconds. The terminals (leads) of the capacitor shall be connected together. A metal foil is tightly wrapped around the body of the capacitor at a distance of about 3 to 4 mm from each terminal. The capacitor is then inserted into a container filled with metal balls approximately 1 mm in diameter. 4,000 VAC(rms) is applied for 60 seconds between the capacitor lead wires and metal balls. The insulation resistance shall be measured with 500 ±50 VDC applied after 60 ±5 seconds of charging. Capacitance is measured at 1 kHz ±20% and 5 Vrms or less (20 ±2°C) A capacitance measurement is made at each step specified: Step Temperature 1 +20 ±2ºC 2 -25 ±2ºC 3 +20 ±2ºC 4 +85 ±2ºC 5 +20 ±2ºC Pre-treatment: Capacitor is stored at 85 ±2ºC for 1 hour and then placed at room condition1 for 24 ±2 hours before measurement. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a tensile force of 10 N is applied to the termination in the direction of its axis and acting in a direction away from the body of the specimen. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a mass force of 5 N is then suspended from the end of the termination. The body of the specimen is then inclined within a period of 2 to 3 seconds, through an angle of approximately 90° in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. One bend immediately followed by a second bend in the opposite direction. The lead wire of the capacitor is dipped into molten solder for 5 ±0.5 seconds. The depth of immersion is up to 1.5 mm (+5/-0 mm) from the root of lead wires. Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C. “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 6 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Soldering Effect (Non-Preheat) Specification Test Method Appearance No visual defect IR 1,000 MΩ Dielectric Strength Per item 1 As shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/-0 mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1 seconds/260°C ±5°C Capacitance Within ±10% Appearance No visual defect IR 1,000 MΩ Dielectric Strength Per item 1 Capacitance Within ±10% Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition1 for 24 ±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. Capacitor is stored at 120°C +0/-5°C for 60 +0/-5 seconds. Then, as shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/-0mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 7.5 +0/-1 seconds/260°C ±5°C Soldering Effect (Preheat) Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition1 for 24 ±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. Capacitance Biased Humidity No visual defect Temperature Characteristics Capacitance Change Y5U Within ±30% DF 5.0% maximum IR 3,000 MΩ minimum Dielectric Strength No failures Appearance No visual defect Capacitance Change Within ±20% IR 3,000 MΩ minimum High Temperature Life Dielectric Strength 1 No failures Steady State Humidity: Load Humidity: 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours. 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours with full rated voltage applied. Post Treatment: Capacitor is stored for 1 to 2 hours at room condition1. Post Treatment: Capacitor is stored for 1 to 2 hours at room condition1. Impulse Voltage: Each individual capacitor is subjected to three 8 kv impulses prior to life testing. 0.9Vp Cx (uF) 0.01 0.1 UPR Vp Voltage Appearance UPP tr (uS) 1.2 1.5 td (uS) 46 47 0.5Vp tr td Time Capacitors are placed in a circulating air oven for a period of 1,000 hours. The air in the oven is maintained at a temperature of 125°C ±2°C throughout the test. The capacitors are subjected to AC 850 Vrms. Each hour the voltage is increased to 1,000 Vrms for 0.1 seconds. . “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 7 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Specification Test Method The capacitor is exposed to a flame for 15 seconds and then removed for 15 seconds. This test is repeated for 5 cycles. The capacitor flame extinguishes as follows: Flame Test Cycle Time 1~4 30 seconds maximum 5 60 seconds maximum The capacitors are individually wrapped in at least one, but not more than two, complete layers of cheesecloth. They are then subjected to 20 discharges. The interval between successive discharges is 5 seconds. The VAC is maintained for 2 minutes after the last discharge. Active Flammability 1 The cheesecloth should not ignite. C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV L1-4 1.5 Mh ±20% 16A Rod core choke Cx Test capacitor R 100 ±2% VAC VR ±5% Ct 3 μF ±5% 10 kV VR Rated Voltage F Fuse, Rated 10A Vt Voltage applied to Ct “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 8 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Specification Test Method The capacitor under test is held into a flame and in a position which best promotes burning. Each specimen is exposed to the flame one time. Passive Flammability The burning time should not exceed 30 seconds. The tissue paper should not ignite. Appearance Capacitance Temperature Cycle Temperature Characteristics Capacitance Change Y5V Within ±20% DF/Q DF ≤ 7.5% IR 3,000 MΩ minimum Dielectric Strength 1 No visual defect No failures Time of exposure to flame: 30 seconds Length of flame: 12 ±1 mm Gas burner length: 35 mm minimum Inside diameter: 0.5 ±0.1 mm Outside diameter: 0.9 mm maximum Gas butane gas purity: 95% minimum The capacitor is subjected to 5 temperature cycles. Temperature Cycle Step Temperature (°C) Dwell Time (minutes) 1 -40 +0/-3 30 2 Room temperature 3 3 125 +3/-0 30 4 Room temperature 3 Transition Time (minutes) 3 Pre-treatment: Capacitor shall be stored at 85 ±2 for 1 hour then placed at room condition1 for 24 ±2 hours. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 9 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Soldering and Mounting Information Soldering: When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks that can crack the ceramic element. When soldering these capacitors with a soldering iron, it should be performed under the following conditions: • Temperature of iron-tip: 400ºC maximum • Soldering iron wattage: 50 W maximum • Soldering time: 3.5 seconds maximum Cleaning (ultrasonic cleaning): To perform ultrasonic cleaning, observe the following conditions: • Rinse bath capacity: Output of 20 watts per liter or less • Rinsing time: 5 minute maximum • Do not vibrate the PCB/PWB directly • Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires Construction Epoxy Encapsulation (0.4 mm Minimum Thickness, Pigment = Blue/UL 94 V-0) Detailed Cross Section Lead Attach Solder (Sn96.5/Ag3/Cu0.5) Dielectric Material (BaTiO3) Electrode (Ag – Glass Frit) Lead Attach Solder (Sn96.5/Ag3/Cu0.5) Electrode (Ag – Glass Frit) Lead Wire Core Metal Barrier Layer Steel Cu 100% Sn Finish Layer (3-7 µm) Dielectric Material (BaTiO3) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 10 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Marking These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated capacitance and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.) Single Sided Rated Capacitance (3 Numeric Characters) KEMET ID Type Designation (2 Characters) Capacitance Tolerance Code (1 Character) VDE & ENEC approval marks IEC 60384-14 3rd (2005) Date/Lot Code (See Table Below) Capacitor Class and Rated Voltage UL approval mark Double Sided Front Back Rated Capacitance (3 Numeric Characters) KEMET ID Capacitance Tolerance Code (1 Character) Type Designation (2 Characters) Capacitor Class and Rated Voltage UL approval mark VDE & ENEC approval marks IEC 60384-14 3rd (2005) Date/Lot Code (See Table Below) Date/Lot Code Explanation 6 Last digit of year, e.g., 6 = 2016 C 6 1234 Manufacturing Month: Manufacturing Location Code 1-9 = Jan - Sept A = October N = November D = December Last 4 digits of lot no. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 11 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Packaging Quantities Capacitor Body Diameter (mm) Body Diameter Code1 7.0 0 8.0 1 9.0 2 10.0 3 11.0 4 13.0 6 14.0 7 15.0 8 Bulk Bag (Loose) Ammo Pack (Carrier Tape) Component pitch on carrier tape2 25.4 mm 1,000 pieces/box 500 pieces/bag 500 pieces/box The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document. 2 For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specifications" sections of this document. 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 12 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Figure 1 - Ammo Pack Taping Format (10 mm Lead Spacing) Table 3 – Ammo Pack Taping Specifications Lead Spacing 10 mm Lead Style Straight Item Preformed1 Symbol Dimensions (mm) Lead Spacing F 10.0 ±1.0 Component Pitch P 25.4 ±2 Sprocket Hole Pitch P0 12.7 ±0.3 Sprocket Hole Center to Component Center P2 12.7 ±1.5 Sprocket Hole Center to Lead Center P1 7.7 ±1.5 Body Diameter D See Table 1 - Product Ordering Codes and Ratings Component Alignment (side/side ) ∆S 0 ±2.0 Carrier Tape Width W 18.0 +1.0/-0.5 Sprocket Hole Position W1 9.0 ±0.5 Height to Seating Plane (preformed leads ) H0 N/A 18.0 +2.0/-0 Height to Seating Plane (straight leads) H 20.0 +1.5/-1.0 N/A 2 1 2 Lead Protrusion ℓ 2.0 maximum Diameter of Sprocket Hole D0 4.0 ±0.2 Lead Diameter φd 0.55 ±0.1 Carrier Tape Thickness t1 0.6 ±0.3 Total Thickness (Carrier Tape, Hold-Down Tape and Lead) t2 1.5 maximum ∆h1 ∆h2 2.0 maximum 2.0 maximum Cut Out Length L 11.0 maximum Hold-Down Tape Width W0 11.0 minimum Hold-Down Tape Position W2 Coating Extension on Leads (meniscus) e Body Thickness T 1.5 ±1.5 3.0 maximum for straight lead; not to exceed the bend for preformed1 lead configurations. 7.0 Maximum Component Alignment (front/back ) Preformed (crimped) lead configurations include vertical kink and outside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 13 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Application Notes: Storage and Operating Conditions: The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably within 6 months of receipt. Working Voltage: Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a voltage rating greater than or equal to these irregular voltages. Operating Temperature and Self-Generating Heat: The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C). Handling - Vibration and Impact: Do not expose these devices or their leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 14 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) KEMET Corporation World Headquarters Europe Asia Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel: 389-2-55-14-623 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Wyboston, United Kingdom Tel: 44-1480-273082 Taipei, Taiwan Tel: 886-2-27528585 Espoo, Finland Tel: 358-9-5406-5000 Southeast Asia Singapore Tel: 65-6701-8033 2835 KEMET Way Simpsonville, SC 29681 Northeast Wilmington, MA Tel: 978-658-1663 Southeast Lake Mary, FL Tel: 407-855-8886 Central Novi, MI Tel: 248-994-1030 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Irving, TX Tel: 972-915-6041 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 15 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 6/10/2016 16