REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED D Changed figure 1; Removed note 3 for case outlines X and Y. Added vendor cage 88379 for device types 01 through 04. -sld 99-03-29 K. A. Cottongim E Added device type 05. Updated drawing to the latest requirements of MIL-PRF-38534. -sld 03-03-17 Raymond Monnin F Figure 1; case outline X, changed the dimension "D" min from 1.654 inches to 1.6 inches. Added cage 0EU86 for device types 01 through 04. Editorial changes troughout. -sld 04-10-21 Raymond Monnin G Added device type 06. Added case outline Z. Editorial changes throughout. -sld 05-02-18 Raymond Monnin H Updated drawing paragraphs. -sld 11-08-24 Charles F. Saffle REV SHEET REV H H H H H H SHEET 15 16 17 18 19 20 REV STATUS REV H H H H H H H H H H H H H H OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 CHECKED BY Michael C. Jones APPROVED BY Kendall A. Cottongim DRAWING APPROVAL DATE 96-04-22 REVISION LEVEL H http://www.landandmaritime.dla.mil MICROCIRCUIT, MEMORY, DIGITAL, FLASH EPROM, 512K x 8-BIT, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-96692 20 5962-E372-11 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 96692 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) T Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 02 03 04 05 06 Generic number F512K8-150, F040-150 F512K8-120, F040-120 F512K8-090, F040-90 F512K8-070, F040-70 F512K8-060, F040-60 F040-55 Circuit function EPROM, FLASH, 512K x 8-bit EPROM, FLASH, 512K x 8-bit EPROM, FLASH, 512K x 8-bit EPROM, FLASH, 512K x 8-bit EPROM ,FLASH, 512K x 8-bit EPROM, FLASH, 512K x 8-bit Access time 150 ns 120 ns 90 ns 70 ns 60 ns 55 ns 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator T U X Y Z See figure 1 See figure 1 See figure 1 See figure 1 CQCC1-N32 Terminals 32 32 32 32 32 Package style Ceramic flatpack, lead formed Ceramic flatpack Co-fired ceramic, single cavity Co-fired ceramic, single cavity, SOJ Rectangular leadless chip carrier 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) 2/ ................................................... Signal voltage range (any pin except A9 ) 2/ ............................ Power dissipation (PD) ............................................................... -2.0 V dc to +7.0 V dc -2.0 V dc to +7.0 V dc 0.33 W maximum at 5 MHz Storage temperature range ........................................................ Lead temperature (soldering, 10 seconds) ................................ Data retention ............................................................................ Endurance (write/erase cycles) .................................................. A9 voltage for sector protect (VID) 3/ ......................................... 1.4 Recommended operating conditions. -65C to +150C +300C 10 years minimum 10,000 cycles minimum -2.0 V dc to +14.0 V dc Supply voltage range (VCC) ........................................................ Input low voltage range (VIL) ...................................................... Input high voltage range (VIH) .................................................... +4.5 V dc to +5.5 V dc -0.5 V dc to +0.8 V dc +2.0 V dc to VCC + 0.5 V dc Case operating temperature range (TC) ..................................... A9 voltage for sector protect (VID) .............................................. -55C to +125C +11.5 V dc to +12.5 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. 1/ 2/ 3/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Minimum DC voltage on input or I/O pins is -0.5 V dc. During voltage transitions, input may overshoot VSS to -2.0 V dc for periods of up to 20 ns. Maximum DC voltage on output and I/O pins is VCC + 0.5 V dc. During voltage transitions, outputs may overshoot to VCC + 2.0 V dc for periods of up to 20 ns. Minimum DC input voltage on A9 pin is -0.5 V dc. During voltage transitions, A9 may overshoot VSS to -2.0 V dc for periods of up to 20 ns. Maximum DC input voltage on A9 is +13.5 V dc which may overshoot to +14.0 V dc for periods up to 20 ns. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 3 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, and 6. 3.2.5 Block diagram. The block diagram shall be as specified on figure 7. 3.2.6 Output load circuit. The output load circuit shall be as specified on figure 8. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Programming procedure. The programming procedure shall be as specified by the manufacturer and shall be available upon request. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 4 3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This reprogrammability test shall be done for the initial characterization and after any design process changes which may affect the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of program/erase cycles listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall be done for initial characterization and after any design process change which may affect data retention. The methods and procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max DC parameters Input leakage current ILI VCC = 5.5 V dc, VIN = GND to VCC 1,2,3 All 10 A Output leakage current ILO VCC = 5.5 V dc, VIN = GND to VCC 1,2,3 All 10 A VCC active current for read ICC1 CS = VIL, OE = VIH, 1,2,3 All 35 mA 1,2,3 All 50 mA 1,2,3 All 1.6 mA 0.8 V f = 5 MHz, VCC = 5.5 V dc VCC active current for program or erase 3/ ICC2 VCC standby current ISB CS = VIL, OE = VIH, VCC = 5.5 V dc VCC = 5.5 V dc , CS = VIH, f = 5 MHz Input low level 3/ VIL 1,2,3 All Input high level 3/ VIH 1,2,3 All Output low voltage VOL VCC = 4.5 V, IOL = 8.0 mA 1,2,3 All Output high voltage VOH VCC = 4.5 V, IOH = -2.5 mA 1,2,3 All CAD VIN = 0 V, f = 1.0 MHz, 4 All 15 pF VIN = 0 V, f = 1.0 MHz, 4 All 15 pF 2.0 V 0.45 V V 0.85 x VCC Dynamic characteristics Address capacitance 3/ TA = +25 C Output enable 3/ capacitance COE TA = +25C See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Group A subgroups Conditions 1/ 2/ -55C TA +125C unless otherwise specified Device types Limits Min Unit Max Dynamic characterisitics - Continued Write enable capacitance 3/ CWE VIN = 0 V, f = 1.0 MHz, 4 All 15 pF VIN = 0 V, f = 1.0 MHz, 4 All 15 pF VIN = 0 V, f = 1.0 MHz, 4 All 15 pF See 4.3.1c 7, 8A,8B All TA = +25 C Chip select capacitance 3/ CCS TA = +25 C Data I/O capacitance 3/ CI/O TA = +25 C Functional testing Functional tests Read cycle AC timing characteristics Read cycle time 3/ tRC See figure 4 9,10,11 01 02 03 04 05 06 Address access time tACC See figure 4 9,10,11 01 02 03 04 05 06 150 120 90 70 60 55 ns Chip select access time tCE See figure 4 9,10,11 01 02 03 04 05 06 150 120 90 70 60 55 ns 150 120 90 70 60 55 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Group A subgroups Conditions 1/ 2/ -55C TA +125C unless otherwise specified Device types Limits Min Unit Max Read cycle AC timing characteristics - Continued Output enable to output valid tOE See figure 4 9,10,11 01 02 03,04 05,06 Output hold from address, tOH See figure 4 9,10,11 All 0 ns 55 50 35 30 ns CS or OE change, whichever is first 3/ Write/Erase/Program AC timing characteristics WE controlled Write cycle time 3/ tWC See figure 5 9,10,11 01 02 03 04 05 06 150 120 90 70 60 55 ns Chip select setup time tCS See figure 5 9,10,11 All 0 ns Write enable pulse width tWP See figure 5 9,10,11 01,02 03,04 05 06 50 45 40 35 ns Address setup time tAS See figure 5 9,10,11 All 0 ns Data setup time tDS See figure 5 9,10,11 01,02 03,04 05 06 50 45 40 30 ns Data hold time tDH See figure 5 9,10,11 All 0 ns Address hold time tAH See figure 5 9,10,11 01,02 03,04 05 06 50 45 45 40 ns Write enable pulse high 3/ tWPH See figure 5 9,10,11 All 20 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Group A subgroups Conditions 1/ 2/ -55C TA +125C unless otherwise specified Device types Limits Min Unit Max Write/Erase/Program AC timing characteristics CS controlled. Write cycle time 3/ tWC See figure 6 9,10,11 01 02 03 04 05 06 150 120 90 70 60 55 ns Write enable setup time tWS See figure 6 9,10,11 All 0 ns Chip select pulse width tCP See figure 6 9,10,11 01,02 03,04 05 06 50 45 40 35 ns Address setup time tAS See figure 6 9,10,11 All 0 ns Data hold time tDH See figure 6 9,10,11 All 0 ns Data setup time tDS See figure 6 9,10,11 01,02 03,04 05 06 50 45 40 30 ns Address hold time tAH See figure 6 9,10,11 01,02 03,04 05 06 50 45 45 40 ns Chip select pulse width high 3/ tCPH See figure 6 9,10,11 All 20 ns 1/ Unless otherwise specified, 4.5 V dc VCC 5.5 V dc and VSS = 0 V. 2/ Unless otherwise specified, the DC test conditions are as follows: Input pulse levels: VIH = VCC - 0.3 V and VIL = 0.3 V. Unless otherwise specified, the AC test conditions are as follows: Input pulse levels: VIL = 0 V and VIH = 3.0 V. Input rise and fall times: 5 nanoseconds. Input and output timing reference levels: 1.5 V. Output load circuit as specified in figure 8. 3/ Parameters shall be tested as part of device characterization and after design and process changes. Parameters shall be tested to the limits specified in table I for all lots not specifically tested. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 9 Case outline T. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 10 Case outline T - Continued. Symbol Millimeters Min Inches Max A Min Max 3.35 .132 A1 2.41 3.18 .095 .125 A2 0.08 0.18 .003 .007 b 0.38 0.48 .015 .019 C 0.10 0.18 .004 .007 C2 0.76 TYP D 20.57 D1 .030 TYP 21.08 .810 19.05 TYP .830 .750 TYP E 10.29 10.54 .405 .415 E1 13.34 13.59 .525 .535 E2 7.75 8.00 .305 .315 E3 1.27 TYP .050 TYP eA 11.07 TYP .436 TYP e 1.27 TYP .050 TYP L 1.52 TYP .060 TYP Q 0.56 R 0.71 .022 0.18 TYP .028 .007 TYP NOTES: 1. The U.S preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. For solder lead finish, dimensions b and C will increase by +.003 inches (+0.08 mm). 3. Pin numbers are for reference only. 4. The case outline T is available in either a pedestal or non-pedestal package. The Q dimension only applies to the pedestal version of case outline T. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 11 Case outline U. Symbol Millimeters Min Inches Max A Min Max 3.18 .125 b 0.38 0.48 .015 .019 C 0.10 0.18 .004 .007 D 20.57 21.08 .810 .830 D1 19.05 TYP .750 TYP E 10.29 10.54 .405 .415 E1 7.75 8.00 .305 .315 E2 1.27 TYP .050 TYP e 1.27 TYP .050 TYP L 9.65 10.67 .380 .420 Q 0.56 0.71 .022 .028 NOTES: 1. The U.S preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. For solder lead finish, dimensions b and C will increase by +.003 inches (+0.08 mm). 3. Pin numbers are for reference only. 4. The case outline U is available in either a pedestal or non-pedestal package. The Q dimension only applies to the pedestal version of case outline U. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 12 Case outline X. Symbol Millimeters Inches Min Max Min Max A 3.56 5.08 .140 .200 A1 0.48 1.19 .019 .047 A2 3.18 4.90 .125 .193 B 0.20 0.30 .009 .012 B1 14.94 15.67 .588 .617 D 40.64 42.82 1.6 1.686 D1 14.73 15.37 .580 .605 D2 37.90 38.30 1.492 1.508 e 2.54 BSC e1 0.41 .100 BSC 0.51 .016 .020 NOTES: 1. The U.S preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. For solder lead finish, dimensions B and e1 will increase by +.003 inches (+0.08mm). 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 13 Case outline Y. Symbol Millimeters Inches Min Max Min Max A 2.67 4.06 .105 .160 A1 1.02 1.52 .040 .060 B1 9.30 9.80 .366 .386 c 0.15 0.25 .006 .010 D 20.83 21.35 .820 .840 D1 10.80 11.05 .425 .435 D2 18.85 19.25 .742 .758 e 1.27 BSC e1 0.38 R .050 BSC 0.48 .015 8.89 BSC .019 .350 BSC NOTES: 1. The U.S preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines- Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 14 Device types All Device types All Case outlines All Case outlines All Terminal number Terminal symbol Terminal number Terminal symbol 1 A18 17 I/O3 2 A16 18 I/O4 3 A15 19 I/O5 4 A12 20 I/O6 5 A7 21 I/O7 6 A6 22 CS 7 A5 23 A10 8 A4 24 OE 9 A3 25 A11 10 A2 26 A9 11 A1 27 A8 12 A0 28 A13 13 I/O0 29 A14 14 I/O1 30 A17 15 I/O2 31 WE 16 Ground 32 VCC FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 15 CS OE WE I/O MODE VIL VIL VIH DOUT Read VIL VIH VIL DIN Write VIH X X High Z Standby VIL VIH VIH High Z Output disable NOTES: 1. H = VIH = High Logic Level 2. L = VIL = Low Logic Level 3. 4. X = Do not care (either high or low) High Z = High Impedance State FIGURE 3. Truth table. FIGURE 4. Read cycle timing diagram. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 16 FIGURE 5. Write/Erase/Program operations, WE controlled. FIGURE 6. Write/Erase/Program operations, CS controlled. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 17 FIGURE 7. Block diagram . Parameter Typ. Unit Input pulse level 0 - 3.0 V Input rise and fall 5 ns Input and output reference level 1.5 V Output load capacitance 50 pF NOTES: 1. V is programmable from -2 V to +7 V. Z 2. I OL and I OH are programmable from 0 to 16 mA. 3. Tester impedance is Z = 75 ohms. O 4. V is typically the midpoint of V Z 5. I OL and I OH OL and V OH . are adjusted to simulate a typical resistive load circuit. 6. ATE tester includes jig capacitance. FIGURE 8. Output load circuit. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 18 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1,4,7,9 Final electrical parameters 1*,2,3,4,7,8A,8B,9,10,11 Group A test requirements 1,2,3,4,7,8A,8B,9,10,11 Group C end-point electrical parameters 1,2,3,4,7,8A,8B,9,10,11 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) (2) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. TA as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 5 and 6 shall be omitted. c. Subgroups 7, 8A, and 8B shall include verification of the truth table on figure 3. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 19 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) (2) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. (4) The checkerboard data pattern shall be verified after burn-in as part of end-point electrical testing. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime -VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-96692 A REVISION LEVEL H SHEET 20 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 11-08-24 Approved sources of supply for SMD 5962-96692 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9669201HTA 5962-9669201HTA 5962-9669201HTA 5962-9669201HTC 5962-9669201HTC 5962-9669201HTC 5962-9669201HUA 5962-9669201HUA 5962-9669201HUA 5962-9669201HUC 5962-9669201HUC 5962-9669201HUC 5962-9669201HXA 5962-9669201HXA 5962-9669201HXA 5962-9669201HXC 5962-9669201HXC 5962-9669201HXC 5962-9669201HYA 5962-9669201HYC 5962-9669201HZA 5962-9669201HZC 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 0EU86 0EU86 AS29F040DCG-150/Q WMF512K8-150FFQ5 ACT-F512K8N-150F7Q AS29F040DCG-150/Q WMF512K8-150FFQ5 ACT-F512K8N-150F7Q AS29F040F-150/Q WMF512K8-150FEQ5 ACT-F512K8N-150F6Q AS29F040F-150/Q WMF512K8-150FEQ5 ACT-F512K8N-150F6Q AS29F040CW-150/Q WMF512K8-150CQ5 ACT-F512K8N-150P4Q AS29F040CW-150/Q WMF512K8-150CQ5 ACT-F512K8N-150P4Q WMF512K8-150DEQ5 WMF512K8-150DEQ5 AS29F040ECA-150/Q AS29F040ECA-150/Q 5962-9669202HTA 5962-9669202HTA 5962-9669202HTA 5962-9669202HTC 5962-9669202HTC 5962-9669202HTC 5962-9669202HUA 5962-9669202HUA 5962-9669202HUA 5962-9669202HUC 5962-9669202HUC 5962-9669202HUC 5962-9669202HXA 5962-9669202HXA 5962-9669202HXA 5962-9669202HXC 5962-9669202HXC 5962-9669202HXC 5962-9669202HYA 5962-9669202HYC 5962-9669202HZA 5962-9669202HZC 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 0EU86 0EU86 AS29F040DCG-120/Q WMF512K8-120FFQ5 ACT-F512K8N-120F7Q AS29F040DCG-120/Q WMF512K8-120FFQ5 ACT-F512K8N-120F7Q AS29F040F-120/Q WMF512K8-120FEQ5 ACT-F512K8N-120F6Q AS29F040F-120/Q WMF512K8-120FEQ5 ACT-F512K8N-120F6Q AS29F040CW-120/Q WMF512K8-120CQ5 ACT-F512K8N-120P4Q AS29F040CW-120/Q WMF512K8-120CQ5 ACT-F512K8N-120P4Q WMF512K8-120DEQ5 WMF512K8-120DEQ5 AS29F040ECA-120/Q AS29F040ECA-120/Q See footnotes at end of table. 1 of 4 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 11-08-24 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9669203HTA 5962-9669203HTA 5962-9669203HTA 5962-9669203HTC 5962-9669203HTC 5962-9669203HTC 5962-9669203HUA 5962-9669203HUA 5962-9669203HUA 5962-9669203HUC 5962-9669203HUC 5962-9669203HUC 5962-9669203HXA 5962-9669203HXA 5962-9669203HXA 5962-9669203HXC 5962-9669203HXC 5962-9669203HXC 5962-9669203HYA 5962-9669203HYC 5962-9669203HZA 5962-9669203HZC 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 0EU86 0EU86 AS29F040DCG-90/Q WMF512K8-90FFQ5 ACT-F512K8N-090F7Q AS29F040DCG-90/Q WMF512K8-90FFQ5 ACT-F512K8N-090F7Q AS29F040F-90/Q WMF512K8-90FEQ5 ACT-F512K8N-090F6Q AS29F040F-90/Q WMF512K8-90FEQ5 ACT-F512K8N-090F6Q AS29F040CW-90/Q WMF512K8-90CQ5 ACT-F512K8N-090P4Q AS29F040CW-90/Q WMF512K8-90CQ5 ACT-F512K8N-090P4Q WMF512K8-90DEQ5 WMF512K8-90DEQ5 AS29F040ECA-90/Q AS29F040ECA-90/Q 5962-9669204HTA 5962-9669204HTA 5962-9669204HTA 5962-9669204HTC 5962-9669204HTC 5962-9669204HTC 5962-9669204HUA 5962-9669204HUA 5962-9669204HUA 5962-9669204HUC 5962-9669204HUC 5962-9669204HUC 5962-9669204HXA 5962-9669204HXA 5962-9669204HXA 5962-9669204HXC 5962-9669204HXC 5962-9669204HXC 5962-9669204HYA 5962-9669204HYC 5962-9669204HZA 5962-9669204HZC 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 0EU86 0EU86 AS29F040DCG-70/Q WMF512K8-70FFQ5 ACT-F512K8N-070F7Q AS29F040DCG-70/Q WMF512K8-70FFQ5 ACT-F512K8N-070F7Q AS29F040F-70/Q WMF512K8-70FEQ5 ACT-F512K8N-070F6Q AS29F040F-70/Q WMF512K8-70FEQ5 ACT-F512K8N-070F6Q AS29F040CW-70/Q WMF512K8-70CQ5 ACT-F512K8N-070P4Q AS29F040CW-70/Q WMF512K8-70CQ5 ACT-F512K8N-070P4Q WMF512K8-70DEQ5 WMF512K8-70DEQ5 AS29F040ECA-70/Q AS29F040ECA-70/Q See footnotes at end of table. 2 of 4 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 11-08-24 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9669205HTA 5962-9669205HTA 5962-9669205HTC 5962-9669205HTC 5962-9669205HUA 5962-9669205HUA 5962-9669205HUC 5962-9669205HUC 5962-9669205HXA 5962-9669205HXA 5962-9669205HXA 5962-9669205HXC 5962-9669205HXC 5962-9669205HXC 5962-9669205HYA 5962-9669205HYC 5962-9669205HZA 5962-9669205HZC 0EU86 54230 0EU86 54230 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 54230 54230 0EU86 0EU86 AS29F040DCG-60/Q WMF512K8-60FFQ5 AS29F040DCG-60/Q WMF512K8-60FFQ5 AS29F040F-60/Q WMF512K8-60FEQ5 AS29F040F-60/Q WMF512K8-60FEQ5 AS29F040CW-60/Q WMF512K8-60CQ5 ACT-F512K8N-060P4Q AS29F040CW-60/Q WMF512K8-60CQ5 ACT-F512K8N-060P4Q WMF512K8-60DEQ5 WMF512K8-60DEQ5 AS29F040ECA-60/Q AS29F040ECA-60/Q 5962-9669206HTA 5962-9669206HTC 5962-9669206HUA 5962-9669206HUC 5962-9669206HXA 5962-9669206HXC 5962-9669206HZA 5962-9669206HZC 0EU86 0EU86 0EU86 0EU86 0EU86 0EU86 0EU86 0EU86 AS29F040DCG-55/Q AS29F040DCG-55/Q AS29F040F-55/Q AS29F040F-55/Q AS29F040CW-55/Q AS29F040CW-55/Q AS29F040ECA-55/Q AS29F040ECA-55/Q 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor for its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3 of 4 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 11-08-24 Vendor CAGE number Vendor name and address 0EU86 Austin Semiconductor, Incorporated DBA Micross Components Suite 105 8701 Cross Park Drive Austin, TX 78754 54230 White Electronic Designs Corporation Military Division 3601 East University Drive Phoenix, AZ 85034 88379 Aeroflex Palinview Incorporated 35 South Service Road Plainview NY, 11803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 4 of 4