REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device type 05. Added case outlines M, N, 4, 5, 6, 7, and 8. Added vendor cage code 88379. 96-08-30 K. A. Cottongim B Figure 1; For case outlines 5, 6, 7 and 8 changed dimension D3 min and max from 1.030 and 1.040 inches to 1.020 and 1.060 inches. Changed dimension A min from .156 inches to .135 inches. Changed dimension L min from .145 inches to .132 inches. -sld 98-06-25 K.A. Cottongim C Added case outline 9. Figure 1; changed case outline M to be either a single or dual cavity package. Figure 1; changed the dimension A2 max limit from .015 inches to .025 inches for case outline M. Added thermal resistance ratings for all case outlines to paragraph 1.3 . Added vendor cage 88379 for case outline M, device types 01 through 05. Table I; changed IOL from 12.0 mA to 8.0 mA for the VOL test. -sld 00-06-20 Raymond Monnin D Added vendor cage code 0EU86 for device types 01 through 05, case outline N. Drawing updated to reflect current requirements. -sld 03-01-13 Raymond Monnin E Added case outline A. -sld 03-02-21 Raymond Monnin F Added case outline B. Added note to paragraph 1.2.4. -sld 03-11-10 Raymond Monnin G Updated drawing paragraphs. -sld 12-11-09 Charles F. Saffle REV G SHEET 35 REV G G G G G G G G G G G G G G G SHEET 15 16 17 18 19 20 G G G G G 21 22 23 24 25 26 27 28 29 30 31 32 33 34 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 CHECKED BY Michael C. Jones APPROVED BY Kendall A. Cottongim DRAWING APPROVAL DATE 94-12-16 REVISION LEVEL G http://www.landandmaritime.dla.mil/ MICROCIRCUIT, HYBRID, DIGITAL, FLASH ERASABLE/PROGRAMMABLE READ ONLY MEMORY, 128K x 32-BIT SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-94716 35 5962-E049-13 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 94716 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) A Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 02 03 04 05 F128K32-150 F128K32-120 F128K32-090 F128K32-070 F128K32-060 Circuit function EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM ,FLASH, 128K x 32-bit Access time 150 ns 120 ns 90 ns 70 ns 60 ns 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter A B M 1/ N S T U V W X Y Z 4 5 6 7 8 9 1/ Descriptive designator See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 Terminals 68 68 68 68 66 66 66 66 66 66 66 66 66 66 66 66 66 68 Package style Co-fired ceramic, single cavity, quad flat pack Co-fired ceramic, single cavity, quad flat pack Co-fired ceramic, single/dual cavity, quad flatpack, lead formed Co-fired ceramic, single cavity, quad flatpack, lead formed Hex-in-line, single cavity, with standoffs Hex-in-line, single cacvity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Ceramic, single cavity, quad flat pack 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs Co-fired ceramic, single cavity, ultra low profile, quad flatpack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 2/ 1/ 2/ 3/ 4/ Supply voltage range (VCC) 3/ ................................................... Signal voltage range (any pin except A9 ) 3/ ............................ Power dissipation (PD) ............................................................... -2.0 V dc to +7.0 V dc -2.0 V dc to +7.0 V dc 1.1 W Thermal resistance, junction-to-case (θJC): Case outline M ....................................................................... Case outline A and N.............................................................. Case outline 4 ........................................................................ Case outlines B and 9 ............................................................ Case outlines 5, 6, 7, and 8 .................................................... Case outlines S, T, U, V, W, X, Y, and Z ................................ Storage temperature range ........................................................ Lead temperature (soldering, 10 seconds) ................................ Data retention ............................................................................ Endurance (write/erase cycles) .................................................. A9 voltage for sector protect (VID) 4/ ......................................... 11.3°C/W 9°C/W 4.07°C/W 4.57°C/W 13.13°C/W 10.63°C/W -65°C to +150°C +300°C 10 years minimum 10,000 cycles minimum -2.0 V dc to +14.0 V dc Due to the short leads of case outlines M (single cavity) and case outline 9, caution should be taken if the system application is to be used where extreme thermal transitions can occur. Case outline A can be used if longer leads are necessary. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Minimum DC voltage on input or I/O pins is -0.5 V dc. During voltage transitions, input may overshoot VSS to -2.0 V dc for periods of up to 20 ns. Maximum DC voltage on output and I/O pins is VCC + 0.5 V dc. During voltage transitions, outputs may overshoot to VCC + 2.0 V dc for periods of up to 20 ns. Minimum DC input voltage on A9 pin is -0.5 V dc. During voltage transitions, A9 may overshoot VSS to -2.0 V dc for periods of up to 20 ns. Maximum DC input voltage on A9 is +13.5 V dc which may overshoot to +14.0 V dc for periods of up to 20 ns. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 3 1.4 Recommended operating conditions. Supply voltage range (VCC) ........................................................ Input low voltage range (VIL) ...................................................... Input high voltage range (VIH) .................................................... +4.5 V dc to +5.5 V dc -0.5 V dc to +0.8 V dc +2.0 V dc to VCC + 0.3 V dc Case operating temperature range (TC) ..................................... A9 voltage for sector protect (VID) .............................................. -55°C to +125°C +11.5 V dc to +12.5 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify, or optimize the tests and inspections herein, however, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 4 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, and 6 . 3.2.5 Block diagram. The block diagram shall be as specified on figure 7. 3.2.6 Output load circuit. The output load circuit shall be as specified on figure 8. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Programming procedure. The programming procedure shall be as specified by the manufacturer and shall be available upon request. 3.6 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This reprogrammability test shall be done for the initial characterization and after any design process changes which may affect the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of program/erase cycles listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall be done for initial characterization and after any design process change which may affect data retention. The methods and procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55°C ≤ TA ≤+125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max DC parameters Input leakage current ILI VCC = 5.5 V dc, VIN = GND or VCC 1,2,3 All 10 µA Output leakage current ILO VCC = 5.5 V dc, VIN = GND or VCC 1,2,3 All 10 µA VCC active current for read ICC1 CS = VIL, OE = VIH, 1,2,3 All 140 mA 1,2,3 All 200 mA 1,2,3 All 6.5 mA 0.8 V f = 5 MHz, VCC = 5.5 V dc VCC active current for program/erase 3/ ICC2 VCC standby current ISB CS = VIL, OE = VIH, f = 5 MHz, VCC = 5.5 V dc CS = VIH, f = 5 MHz, VCC = 5.5 V dc Input low level 3/ VIL 1,2,3 All Input high level 3/ VIH 1,2,3 All Output low voltage VOL VCC = 4.5 V, IOL = 8.0 mA 1,2,3 All Output high voltage VOH1 VCC = 4.5 V, IOH = -2.5 mA 1,2,3 All 0.85 x VCC V VOH2 3/ VCC = 4.5 V, IOH = -100 µA 1,2,3 All VCC - 0.4 V dc V COE VIN = 0 V, f = 1.0 MHz, 4 All 2.0 V 0.45 V Dynamic characteristics OE capacitance 50 pF TA = +25° C See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55°C ≤ TA ≤+125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Dynamic characterisitics - Continued A0-16 capacitance 3/ CAD VIN = 0 V, f = 1.0 MHz, 4 All 50 pF 4 All 20 pF 4 All 50 pF TA = +25° C CS capacitance 3/ CCS VIN = 0 V, f = 1.0 MHz, TA = +25° C WE capacitance 3/ CWE VIN = 0 V, f = 1.0 MHz, TA = +25° C, Case outline 4, only Remaining case outlines 20 I/O0-I/O31 capacitance 3/ CI/O VI/O = 0 V, f = 1.0 MHz, 4 All See 4.3.1c 7, 8A,8B All 20 pF TA = +25° C Functional testing Functional tests Read cycle AC timing characteristics Read cycle time 3/ tRC See figure 4 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Address access time tACC See figure 4 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Chip select access time tCE See figure 4 9,10,11 01 02 03 04 05 150 120 90 70 60 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55°C ≤ TA ≤+125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Read cycle AC timing characteristics - Continued Output enable to output valid tOE See figure 4 9,10,11 01 02 03 04 05 55 50 40 35 30 ns Chip select to output high Z tDF See figure 4 9,10,11 01 02 03 04,05 35 30 25 20 ns OE high to output high Z 3/ tDF See figure 4 9,10,11 01 02 03 04,05 35 30 25 20 ns Output hold from address, CS or OE change, whichever is first 3/ tOH See figure 4 9,10,11 All 0 ns 3/ Write/Erase/Program AC timing characteristics WE controlled Write cycle time 3/ tWC See figure 5 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Chip select setup time tCS See figure 5 9,10,11 All 0 ns Write enable pulse width tWP See figure 5 9,10,11 01,02 03 04 05 50 45 35 30 ns Address setup time tAS See figure 5 9,10,11 All 0 ns Data setup time tDS See figure 5 9,10,11 01,02 03 04,05 50 45 30 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55°C ≤ TA ≤+125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Write/Erase/Program AC timing characteristics WE controlled - Continued. Data hold time tDH See figure 5 9,10,11 All 0 ns Address hold time tAH See figure 5 9,10,11 01,02 03,04, 05 50 45 ns Write enable pulse high 3/ tWPH See figure 5 9,10,11 All 20 ns Read recovery before 3/ write tGHWL See figure 5 9,10,11 All 0 ns Write/Erase/Program AC timing characteristics CS controlled. Write cycle time 3/ tWC See figure 6 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Write enable setup time tWS See figure 6 9,10,11 All 0 ns Chip select pulse width tCP See figure 6 9,10,11 01,02 03 04 05 50 45 35 30 ns Address setup time tAS See figure 6 9,10,11 All 0 ns Data hold time tDH See figure 6 9,10,11 All 0 ns Data setup time tDS See figure 6 9,10,11 01,02 03 04,05 50 45 30 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55°C ≤ TA ≤+125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max Write/Erase/Program AC characteristics CS controlled - Continued. Address hold time tAH See figure 6 9,10,11 01,02 03,04, 05 50 45 ns Chip select pulse width high 3/ tCPH See figure 6 9,10,11 All 20 ns Read recovery before 3/ write tGHEL 9,10,11 All 0 ns 1/ Unless otherwise specified, 4.5 V dc ≤ V CC ≤ 5.5 V dc and V SS = 0 V. 2/ Unless otherwise specified, the DC test conditions are as follows: Input pulse levels: V = V - 0.3 V and V = 0.3V. IH CC IL Unless otherwise specified, the AC test conditions are as follows: Input pulse levels: V = 0 V and V = 3.0 V. IL IH Input rise and fall times: 5 nanoseconds. Input and output timing reference levels: 1.5 V. Output load circuit as specified in figure 8. 3/ Guaranteed by design, but not tested. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 10 Case outline A. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 11 Case outline A - Continued. Symbol Millimeters Min Inches Max A Min Max 5.10 A1 1.37 b 0.33 B .200 .054 0.43 .013 0.25 TYP .017 .010 TYP c 0.23 0.30 .009 .012 D/E 24.9 25.4 .980 1.000 D1/E1 22.10 22.61 .870 .890 D2/E2 20.32 BSC .800 BSC e 1.27 BSC .050 BSC L 0.89 R 1.14 .035 0.25 TYP .045 .010 TYP NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Details of pin 1 identifier are optional, but must be located within the zone indicated. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 12 Case outline M. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 13 Case outline M - Continued. Symbol Millimeters Inches Min Max Min Max A 3.12 5.10 .123 .200 A1 2.30 4.72 .118 .186 A2 0.24 0.64 .005 .025 b 0.33 0.43 .013 .017 B c 0.25 REF 0.23 D/E .010 REF 0.30 .009 20.3 BSC .012 .800 BSC D1/E1 22.10 22.65 .870 .890 D2/E2 24.89 25.35 .980 1.000 D3/E3 23.75 24.28 .936 .956 e 1.27 BSC .050 BSC R 0.25 BSC .010 BSC L1 0.89 1.14 .035 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. 3. Case outline M may be either a single cavity or dual cavity package. Dimension A2 is measured between the lowest horizontal plane of the package and the seating plane of the lead(s). FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 14 Case outline N. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 15 Case outline N - Continued. Symbol Millimeters Inches Min Max Min Max A 3.12 4.06 .123 .160 A2 0.13 0.64 .005 .025 b 0.33 0.43 .013 .017 c 0.23 0.30 .009 .012 D/E 20.3 BSC .800 BSC D1/E1 22.10 22.65 .870 .890 D2/E2 24.89 25.35 .980 1.000 D3/E3 23.75 24.28 .936 .956 e 1.27 BSC .050 BSC R 0.25 BSC .010 BSC L1 0.89 1.14 .035 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. 3. Case outline N is a single cavity package. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 16 Case outlines S, U, W, Y, 5, 6, 7, and 8. FIGURE 1. Case outlines- Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 17 Case outlines S, U, W, and Y only. Symbol Millimeters Inches Min Max Min Max A 5.08 6.22 .200 .245 A1 0.64 0.89 .025 .035 φb 0.41 0.51 .016 .020 φb1 1.14 1.40 .045 .055 φb2 1.65 1.91 .065 .075 D/E 29.72 30.48 1.170 1.200 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 28.96 e L 29.21 1.020 2.54 BSC 3.68 1.150 .100 BSC 3.94 .132 .155 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 18 Case outlines 5, 6, 7, and 8 only. Symbol Millimeters Inches Min Max Min Max A 3.43 4.34 .135 .181 A1 0.64 0.89 .025 .035 φb 0.41 0.51 .016 .020 φb1 1.14 1.40 .045 .055 φb2 1.65 1.91 .065 .075 D/E 27.05 27.56 1.065 1.085 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 25.90 e L 26.92 1.020 2.54 BSC 3.35 1.060 .100 BSC 3.94 .132 .155 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 19 Case outlines T, V, X, and Z. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 20 Case outlines T, V, X, and Z - Continued. Symbol Millimeters Inches Min Max Min Max A 3.30 5.84 .130 .230 φb 0.41 0.51 .016 .020 φb1 0.76 REF .030 REF φb2 1.65 1.91 .065 .075 D/E 26.92 30.48 1.060 1.200 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 26.16 e L 29.21 1.030 2.54 BSC 4.19 1.150 .100 BSC 4.69 .165 .185 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 21 Case outline 4. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 22 Case outline 4 - Continued. Symbol Millimeters Inches Min Max Min Max A 4.46 5.10 .175 .200 A1 1.40 1.65 .055 .065 A2 1.14 1.40 .045 .055 b 0.30 0.46 .012 .018 c 0.23 0.31 .009 .012 D/E 63.63 66.42 2.505 2.615 D1/E1 39.24 40.01 1.545 1.575 D2/E2 73.28 84.20 2.885 3.315 e 1.14 1.40 .045 .055 e1 20.19 20.45 .795 .805 j 4.83 5.33 .190 .210 k 37.72 38.48 1.485 1.515 L 12.19 13.21 .480 .520 S1 9.45 9.86 .372 .388 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 23 Case outlines B and 9. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 24 Case outline B - Continued Symbol Millimeters Min A Inches Max Min Max 4.06 A1 .160 2.79 .110 A2 1.12 1.42 .044 .056 b 0.33 0.43 .013 .017 C 0.15 0.25 .006 .010 D/E 20.32 BSC .800 BSC D1/E1 23.65 24.10 .931 .949 D2/E2 24.89 25.40 .980 1.000 e L1 1.27 BSC 0.51 1.14 .050 BSC .020 .045 Case outline 9 - Continued Symbol Millimeters Min Inches Max Min Max A 3.56 .140 A1 2.79 .110 A2 0.46 0.76 .018 .030 b 0.33 0.43 .013 .017 C 0.15 0.25 .006 .010 D/E 20.32 BSC .800 BSC D1/E1 23.65 24.10 .931 .949 D2/E2 24.89 25.40 .980 1.000 e L1 1.27 BSC 0.51 1.14 .050 BSC .020 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 25 Device types All Device types All Device types All Device types All Case outlines A, B, M, N, 9 Case outlines A, B, M, N, 9 Case outlines A, B, M, N, 9 Case outlines A, B, M, N, 9 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 GND 18 GND 35 OE 52 GND 2 CS3 19 I/O8 36 CS2 53 I/O23 3 A5 20 I/O9 37 NC 54 I/O22 4 A4 21 I/O10 38 WE2 55 I/O21 5 A3 22 I/O11 39 WE3 56 I/O20 6 A2 23 I/O12 40 WE4 57 I/O19 7 A1 24 I/O13 41 NC 58 I/O18 8 A0 25 I/O14 42 NC 59 I/O17 9 NC 26 I/O15 43 NC 60 I/O16 10 I/O0 27 VCC 44 I/O31 61 VCC 11 I/O1 28 A11 45 I/O30 62 A10 12 I/O2 29 A12 46 I/O29 63 A9 13 I/O3 30 A13 47 I/O28 64 A8 14 I/O4 31 A14 48 I/O27 65 A7 15 I/O5 32 A15 49 I/O26 66 A6 16 I/O6 33 A16 50 I/O25 67 WE1 17 I/O7 34 CS1 51 I/O24 68 CS4 FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 26 Device types All Device types All Device types All Device types All Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 I/O8 18 A15 35 I/O25 52 WE3 2 I/O9 19 VCC 36 I/O26 53 CS3 3 I/O10 20 CS1 37 A7 54 GND 4 A14 21 NC 38 A12 55 I/O19 5 A16 22 I/03 39 NC 56 I/O31 6 A11 23 I/015 40 A13 57 I/O30 7 A0 24 I/O14 41 A8 58 I/O29 8 NC 25 I/O13 42 I/O16 59 I/O28 9 I/O0 26 I/O12 43 I/O17 60 A1 10 I/O1 27 OE 44 I/O18 61 A2 11 I/O2 28 NC 45 VCC 62 A3 12 WE2 29 WE1 46 CS4 63 I/O23 13 CS2 30 I/O7 47 WE4 64 I/O22 14 GND 31 I/O6 48 I/O27 65 I/O21 15 I/O11 32 I/O5 49 A4 66 I/O20 16 A10 33 I/O4 50 A5 17 A9 34 I/O24 51 A6 NOTE: Case outlines Y, Z, and 8, pins 8, 21, 28, and 39 are no connects (NC) and for case outlines U, V, and 6, pins 8, 21, 28, and 39 are ground. FIGURE 2. Terminal connections (industrial pin-outs) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 27 Device types All Device types All Device types All Device types All Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 I/O8 18 A12 35 I/O25 52 WE3 2 I/O9 19 VCC 36 I/O26 53 CS3 3 I/O10 20 CS1 37 A6 54 GND 4 A13 21 NC 38 A7 55 I/O19 5 A14 22 I/03 39 NC 56 I/O31 6 A15 23 I/015 40 A8 57 I/O30 7 A16 24 I/O14 41 A9 58 I/O29 8 NC 25 I/O13 42 I/O16 59 I/O28 9 I/O0 26 I/O12 43 I/O17 60 A0 10 I/O1 27 OE 44 I/O18 61 A1 11 I/O2 28 NC 45 VCC 62 A2 12 WE2 29 WE1 46 CS4 63 I/O23 13 CS2 30 I/O7 47 WE4 64 I/O22 14 GND 31 I/O6 48 I/O27 65 I/O21 15 I/O11 32 I/O5 49 A3 66 I/O20 16 A10 33 I/O4 50 A4 17 A11 34 I/O24 51 A5 NOTE: Case outlines W, X, and 7, pins 8, 21, 28, and 39 are no connects (NC) and for case outlines S, T, and 5, pins 8, 21, 28, and 39 are ground. FIGURE 2. Terminal connections (alternative pin-outs) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 28 Device types All Device types All Device types All Device types All Case outline 4 Case outline 4 Case outline 4 Case outline 4 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 GND 18 GND 35 OE 52 GND 2 CS1 19 I/O8 36 CS4 53 I/O23 3 A5 20 I/O9 37 NC 54 I/O22 4 A4 21 I/O10 38 NC 55 I/O21 5 A3 22 I/O11 39 NC 56 I/O20 6 A2 23 I/O12 40 NC 57 I/O19 7 A1 24 I/O13 41 NC 58 I/O18 8 A0 25 I/O14 42 NC 59 I/O17 9 NC 26 I/O15 43 NC 60 I/O16 10 I/O0 27 VCC 44 I/O31 61 VCC 11 I/O1 28 A11 45 I/O30 62 A10 12 I/O2 29 A12 46 I/O29 63 A9 13 I/O3 30 A13 47 I/O28 64 A8 14 I/O4 31 A14 48 I/O27 65 A7 15 I/O5 32 A15 49 I/O26 66 A6 16 I/O6 33 A16 50 I/O25 67 WE 17 I/O7 34 CS2 51 I/O24 68 CS3 FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 29 CS OE WE Data I/O MODE Device current H X X High Z Standby Standby L L H Data out Read Active L H L Data in Write Active NOTES: = High Logic Level 1. H=V 2. L=V 3. 4. X = Do not care (either high or low) High Z = High Impedance State IH IL = Low Logic Level FIGURE 3. Truth table. FIGURE 4. Read cycle timing diagram. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 30 FIGURE 5. Write/Erase/Program operations, WE controlled. NOTES: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device. 4. DOUT is the output of the data written to the device. 5. Figures indicate last two bus cycles of a four bus cycle sequence. FIGURE 6. Write/Erase/Program operations, CS controlled. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 31 Case outlines A, B, M, N, S, T, U, V, W, X, Y, Z, 5, 6, 7, 8, and 9 Case outline 4. FIGURE 7. Block diagrams . STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 32 NOTES: 1. V is programmable from -2 V to +7 V. Z 2. I OL and I OH are programmable from 0 to 16 mA. 3. Tester impedance is Z = 75 ohms. 0 4. V is typically the midpoint of V Z 5. I OL OL and I OH and V . OH are adjusted to simulate a typical resistive load circuit. 6. ATE tester includes jig capacitance. FIGURE 8. Output load circuit. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 33 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1,4,7,9 Final electrical parameters 1*,2,3,4,7,8A,8B,9,10,11 Group A test requirements 1,2,3,4,7,8A,8B,9,10,11 Group C end-point electrical parameters 1,2,3,4,7,8A,8B,9,10,11 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) (2) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. TA as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 5 and 6 shall be omitted. c. Subgroups 7, 8A, and 8B shall include verification of the truth table on figure 3. d. The following data patterns shall be verified during subgroups 7, 8A, and 8B. (1) 0's to all memory cell locations. (2) Checkerboard pattern to entire memory. (3) Checkerboard compliment to entire memory array. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 34 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) (2) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. (4) The checkerboard data pattern shall be verified after burn-in as part of end-point electrical testing. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors, listed in MIL-HDBK103 and QML-38534, have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL G SHEET 35 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 12-11-09 Approved sources of supply for SMD 5962-94716 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ 5962-9471601HAA 5962-9471601HAA 5962-9471601HAC 5962-9471601HAC 5962-9471601HMA 5962-9471601HMA 5962-9471601HMA 5962-9471601HMC 5962-9471601HMC 5962-9471601HMC 5962-9471601HNA 5962-9471601HNA 5962-9471601HNA 5962-9471601HNC 5962-9471601HNC 5962-9471601HNC 5962-9471601HSA 5962-9471601HSC 5962-9471601HTA 5962-9471601HTC 5962-9471601HUA 5962-9471601HUC 5962-9471601HVA 5962-9471601HVC 5962-9471601HWA 5962-9471601HWC 5962-9471601HXA 5962-9471601HXC 5962-9471601HYA 5962-9471601HYC 5962-9471601HZA 5962-9471601HZA 5962-9471601HZC 5962-9471601HZC 5962-9471601H4C 5962-9471601H5A 5962-9471601H5C 5962-9471601H6A 5962-9471601H6C 5962-9471601H7A 5962-9471601H7C 5962-9471601H8A 5962-9471601H8A 5962-9471601H8C 5962-9471601H8C 5962-9471601H9A 5962-9471601H9C 5962-9471601HBA 5962-9471601HBC Vendor CAGE number 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 See footnotes at end of table. 1 of 6 Vendor similar PIN 2/ AS8F128K32Q1-150/Q WF128K32-150G2LQ5 AS8F128K32Q1-150/Q WF128K32-150G2LQ5 AS8F128K32Q-150/Q WF128K32-150G2Q5 ACT-F128K32N-150F5Q AS8F128K32Q-150/Q WF128K32-150G2Q5 ACT-F128K32N-150F5Q AS8F128K32Q-150/Q WF128K32-150G2UQ5 ACT-F128K32N-150F5Q AS8F128K32Q-150/Q WF128K32-150G2UQ5 ACT-F128K32N-150F5Q WF128K32A-150HQ5 WF128K32A-150HQ5 WF128K32A-150HSQ5 WF128K32A-150HSQ5 WF128K32-150HQ5 WF128K32-150HQ5 WF128K32-150HSQ5 WF128K32-150HSQ5 WF128K32NA-150HQ5 WF128K32NA-150HQ5 WF128K32NA-150HSQ5 WF128K32NA-150HSQ5 WF128K32N-150HQ5 WF128K32N-150HQ5 WF128K32N-150HSQ5 ACT-F128K32N-150P3Q WF128K32N-150HSQ5 ACT-F128K32N-150P3Q WF128K32-150G4Q5 WF128K32A-150H1Q5 WF128K32A-150H1Q5 WF128K32-150H1Q5 WF128K32-150H1Q5 WF128K32NA-150H1Q5 WF128K32NA-150H1Q5 WF128K32N-150H1Q5 ACT-F128K32N-150P7Q WF128K32N-150H1Q5 ACT-F128K32N-150P7Q WF128K32-150G1UQ5 WF128K32-150G1UQ5 WF128K32-150G1TQ5 WF128K32-150G1TQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 12-11-09 Standard microcircuit drawing PIN 1/ 5962-9471602HAA 5962-9471602HAA 5962-9471602HAC 5962-9471602HAC 5962-9471602HMA 5962-9471602HMA 5962-9471602HMA 5962-9471602HMC 5962-9471602HMC 5962-9471602HMC 5962-9471602HNA 5962-9471602HNA 5962-9471602HNA 5962-9471602HNC 5962-9471602HNC 5962-9471602HNC 5962-9471602HSA 5962-9471602HSC 5962-9471602HTA 5962-9471602HTC 5962-9471602HUA 5962-9471602HUC 5962-9471602HVA 5962-9471602HVC 5962-9471602HWA 5962-9471602HWC 5962-9471602HXA 5962-9471602HXC 5962-9471602HYA 5962-9471602HYC 5962-9471602HZA 5962-9471602HZA 5962-9471602HZC 5962-9471602HZC 5962-9471602H4C 5962-9471602H5A 5962-9471602H5C 5962-9471602H6A 5962-9471602H6C 5962-9471602H7A 5962-9471602H7C 5962-9471602H8A 5962-9471602H8A 5962-9471602H8C 5962-9471602H8C 5962-9471602H9A 5962-9471602H9C 5962-9471602HBA 5962-9471602HBC Vendor CAGE number 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 See footnotes at end of table. 2 of 6 Vendor similar PIN 2/ AS8F128K32Q1-120/Q WF128K32-120G2LQ5 AS8F128K32Q1-120/Q WF128K32-120G2LQ5 AS8F128K32Q-120/Q WF128K32-120G2Q5 ACT-F128K32N-120F5Q AS8F128K32Q-120/Q WF128K32-120G2Q5 ACT-F128K32N-120F5Q AS8F128K32Q-120/Q WF128K32-120G2UQ5 ACT-F128K32N-120F5Q AS8F128K32Q-120/Q WF128K32-120G2UQ5 ACT-F128K32N-120F5Q WF128K32A-120HQ5 WF128K32A-120HQ5 WF128K32A-120HSQ5 WF128K32A-120HSQ5 WF128K32-120HQ5 WF128K32-120HQ5 WF128K32-120HSQ5 WF128K32-120HSQ5 WF128K32NA-120HQ5 WF128K32NA-120HQ5 WF128K32NA-120HSQ5 WF128K32NA-120HSQ5 WF128K32N-120HQ5 WF128K32N-120HQ5 WF128K32N-120HSQ5 ACT-F128K32N-120P3Q WF128K32N-120HSQ5 ACT-F128K32N-120P3Q WF128K32-120G4Q5 WF128K32A-120H1Q5 WF128K32A-120H1Q5 WF128K32-120H1Q5 WF128K32-120H1Q5 WF128K32NA-120H1Q5 WF128K32NA-120H1Q5 WF128K32N-120H1Q5 ACT-F128K32N-120P7Q WF128K32N-120H1Q5 ACT-F128K32N-120P7Q WF128K32-120G1UQ5 WF128K32-120G1UQ5 WF128K32-120G1TQ5 WF128K32-120G1TQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 12-11-09 Standard microcircuit drawing PIN 1/ 5962-9471603HAA 5962-9471603HAA 5962-9471603HAC 5962-9471603HAC 5962-9471603HMA 5962-9471603HMA 5962-9471603HMA 5962-9471603HMC 5962-9471603HMC 5962-9471603HMC 5962-9471603HNA 5962-9471603HNA 5962-9471603HNA 5962-9471603HNC 5962-9471603HNC 5962-9471603HNC 5962-9471603HSA 5962-9471603HSC 5962-9471603HTA 5962-9471603HTC 5962-9471603HUA 5962-9471603HUC 5962-9471603HVA 5962-9471603HVC 5962-9471603HWA 5962-9471603HWC 5962-9471603HXA 5962-9471603HXC 5962-9471603HYA 5962-9471603HYC 5962-9471603HZA 5962-9471603HZA 5962-9471603HZC 5962-9471603HZC 5962-9471603H4C 5962-9471603H5A 5962-9471603H5C 5962-9471603H6A 5962-9471603H6C 5962-9471603H7A 5962-9471603H7C 5962-9471603H8A 5962-9471603H8A 5962-9471603H8C 5962-9471603H8C 5962-9471603H9A 5962-9471603H9C 5962-9471603HBA 5962-9471603HBC Vendor CAGE number 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 See footnotes at end of table. 3 of 6 Vendor similar PIN 2/ AS8F128K32Q1-90/Q WF128K32-90G2LQ5 AS8F128K32Q1-90/Q WF128K32-90G2LQ5 AS8F128K32Q-90/Q WF128K32-90G2Q5 ACT-F128K32N-090F5Q AS8F128K32Q-90/Q WF128K32-90G2Q5 ACT-F128K32N-090F5Q AS8F128K32Q-90/Q WF128K32-90G2UQ5 ACT-F128K32N-090F5Q AS8F128K32Q-90/Q WF128K32-90G2UQ5 ACT-F128K32N-090F5Q WF128K32A-90HQ5 WF128K32A-90HQ5 WF128K32A-90HSQ5 WF128K32A-90HSQ5 WF128K32-90HQ5 WF128K32-90HQ5 WF128K32-90HSQ5 WF128K32-90HSQ5 WF128K32NA-90HQ5 WF128K32NA-90HQ5 WF128K32NA-90HSQ5 WF128K32NA-90HSQ5 WF128K32N-90HQ5 WF128K32N-90HQ5 WF128K32N-90HSQ5 ACT-F128K32N-090P3Q WF128K32N-90HSQ5 ACT-F128K32N-090P3Q WF128K32-90G4Q5 WF128K32A-90H1Q5 WF128K32A-90H1Q5 WF128K32-90H1Q5 WF128K32-90H1Q5 WF128K32NA-90H1Q5 WF128K32NA-90H1Q5 WF128K32N-90H1Q5 ACT-F128K32N-090P7Q WF128K32N-90H1Q5 ACT-F128K32N-090P7Q WF128K32-90G1UQ5 WF128K32-90G1UQ5 WF128K32-90G1TQ5 WF128K32-90G1TQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 12-11-09 Standard microcircuit drawing PIN 1/ 5962-9471604HAA 5962-9471604HAA 5962-9471604HAC 5962-9471604HAC 5962-9471604HMA 5962-9471604HMA 5962-9471604HMA 5962-9471604HMC 5962-9471604HMC 5962-9471604HMC 5962-9471604HNA 5962-9471604HNA 5962-9471604HNA 5962-9471604HNC 5962-9471604HNC 5962-9471604HNC 5962-9471604HSA 5962-9471604HSC 5962-9471604HTA 5962-9471604HTC 5962-9471604HUA 5962-9471604HUC 5962-9471604HVA 5962-9471604HVC 5962-9471604HWA 5962-9471604HWC 5962-9471604HXA 5962-9471604HXC 5962-9471604HYA 5962-9471604HYC 5962-9471604HZA 5962-9471604HZA 5962-9471604HZC 5962-9471604HZC 5962-9471604H4C 5962-9471604H5A 5962-9471604H5C 5962-9471604H6A 5962-9471604H6C 5962-9471604H7A 5962-9471604H7C 5962-9471604H8A 5962-9471604H8A 5962-9471604H8C 5962-9471604H8C 5962-9471604H9A 5962-9471604H9C 5962-9471604HBA 5962-9471604HBC Vendor CAGE number 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 See footnotes at end of table. 4 of 6 Vendor similar PIN 2/ AS8F128K32Q1-70/Q WF128K32-70G2LQ5 AS8F128K32Q1-70/Q WF128K32-70G2LQ5 AS8F128K32Q-70/Q WF128K32-70G2Q5 ACT-F128K32N-070F5Q AS8F128K32Q-70/Q WF128K32-70G2Q5 ACT-F128K32N-070F5Q AS8F128K32Q-70/Q WF128K32-70G2UQ5 ACT-F128K32N-070F5Q AS8F128K32Q-70/Q WF128K32-70G2UQ5 ACT-F128K32N-070F5Q WF128K32A-70HQ5 WF128K32A-70HQ5 WF128K32A-70HSQ5 WF128K32A-70HSQ5 WF128K32-70HQ5 WF128K32-70HQ5 WF128K32-70HSQ5 WF128K32-70HSQ5 WF128K32NA-70HQ5 WF128K32NA-70HQ5 WF128K32NA-70HSQ5 WF128K32NA-70HSQ5 WF128K32N-70HQ5 WF128K32N-70HQ5 WF128K32N-70HSQ5 ACT-F128K32N-070P3Q WF128K32N-70HSQ5 ACT-F128K32N-070P3Q WF128K32-70G4Q5 WF128K32A-70H1Q5 WF128K32A-70H1Q5 WF128K32-70H1Q5 WF128K32-70H1Q5 WF128K32NA-70H1Q5 WF128K32NA-70H1Q5 WF128K32N-70H1Q5 ACT-F128K32N-070P7Q WF128K32N-70H1Q5 ACT-F128K32N-070P7Q WF128K32-70G1UQ5 WF128K32-70G1UQ5 WF128K32-70G1TQ5 WF128K32-70G1TQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 12-11-09 Standard microcircuit drawing PIN 1/ 5962-9471605HAA 5962-9471605HAA 5962-9471605HAC 5962-9471605HAC 5962-9471605HMA 5962-9471605HMA 5962-9471605HMA 5962-9471605HMC 5962-9471605HMC 5962-9471605HMC 5962-9471605HNA 5962-9471605HNA 5962-9471605HNA 5962-9471605HNC 5962-9471605HNC 5962-9471605HNC 5962-9471605HSA 5962-9471605HSC 5962-9471605HTA 5962-9471605HTC 5962-9471605HUA 5962-9471605HUC 5962-9471605HVA 5962-9471605HVC 5962-9471605HWA 5962-9471605HWC 5962-9471605HXA 5962-9471605HXC 5962-9471605HYA 5962-9471605HYC 5962-9471605HZA 5962-9471605HZA 5962-9471605HZC 5962-9471605HZC 5962-9471605H4C 5962-9471605H5A 5962-9471605H5C 5962-9471605H6A 5962-9471605H6C 5962-9471605H7A 5962-9471605H7C 5962-9471605H8A 5962-9471605H8A 5962-9471605H8C 5962-9471605H8C 5962-9471605H9A 5962-9471605H9C 5962-9471605HBA 5962-9471605HBC Vendor CAGE number 0EU86 54230 0EU86 54230 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 0EU86 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 Vendor similar PIN 2/ AS8F128K32Q1-60/Q WF128K32-60G2LQ5 AS8F128K32Q1-60/Q WF128K32-60G2LQ5 AS8F128K32Q-60/Q WF128K32-60G2Q5 ACT-F128K32N-060F5Q AS8F128K32Q-60/Q WF128K32-60G2Q5 ACT-F128K32N-060F5Q AS8F128K32Q-60/Q WF128K32-60G2UQ5 ACT-F128K32N-060F5Q AS8F128K32Q-60/Q WF128K32-60G2UQ5 ACT-F128K32N-060F5Q WF128K32A-60HQ5 WF128K32A-60HQ5 WF128K32A-60HSQ5 WF128K32A-60HSQ5 WF128K32-60HQ5 WF128K32-60HQ5 WF128K32-60HSQ5 WF128K32-60HSQ5 WF128K32NA-60HQ5 WF128K32NA-60HQ5 WF128K32NA-60HSQ5 WF128K32NA-60HSQ5 WF128K32N-60HQ5 WF128K32N-60HQ5 WF128K32N-60HSQ5 ACT-F128K32N-060P3Q WF128K32N-60HSQ5 ACT-F128K32N-060P3Q WF128K32-60G4Q5 WF128K32A-60H1Q5 WF128K32A-60H1Q5 WF128K32-60H1Q5 WF128K32-60H1Q5 WF128K32NA-60H1Q5 WF128K32NA-60H1Q5 WF128K32N-60H1Q5 ACT-F128K32N-060P7Q WF128K32N-60H1Q5 ACT-F128K32N-060P7Q WF128K32-60G1UQ5 WF128K32-60G1UQ5 WF128K32-60G1TQ5 WF128K32-60G1TQ5 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor for its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 5 of 6 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 12-11-09 Vendor CAGE number Vendor name and address 0EU86 Austin Semiconductor Incorporated DBA Micross Components 8701 Cross Park Drive Suite 105 Austin, TX 78754 54230 White Electronic Designs Corporation 3601 East University Drive Phoenix, AZ 85034 88379 Aeroflex Plainview Incorporated (Aeroflex Microelectronic Solutions) 35 South Service Road Plainview NY, 11803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 6 of 6