REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device type 02. Made corrections to paragraph 1.3 and table I. Added waveform distortion test to table I. Rewrote entire document. 93-06-15 K. A. Cottongim B Added vendor cage number 57363. Added device types 03, 04, 05, and 06. Added case outlines M, N, T, and U. 93-10-08 K. A. Cottongim C Added case outlines 4 and 5. 95-01-13 K. A. Cottongim D Remove vendor cage 8K957. Added vendor cage 88379. Added device types 07, 08, 09, and 10. Updated requirements to MIL-PRF-38534. 95-12-06 K. A. Cottongim E Table I; For the tDT test changed the max limit for device types 07 and 08 from 150 ns to 250 ns. For the tDI-L test changed the max limit for device types 07 and 08 from 250 ns to 450 ns. For the ICC4 test under the conditions block added for device types 07-10 to use 100% duty cycle at 1 MHz, see note 11. Changed the max limit for the ICC4 test, device types 07-10 from 650 mA to 750 mA. -sld 01-06-22 Raymond Monnin F Case outline N, dimension Q maximum, change .122" to .135". 03-12-19 Raymond Monnin G Paragraph 1.2.4, case outline Z, correct terminals from 36 to 24. -gz 08-11-07 Robert M. Heber H Table I, ICC5 test for device types 03 through 06, change test condition from 80% duty cycle at 1 MHz to 75% duty cycle at 1 MHz. -gz 10-07-20 Charles F. Saffle J Updated drawing paragraphs. -sld 12-05-07 Charles F. Saffle K Add case outline 6. -gc 13-01-22 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV K K K K K K K K K K K K K SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 REV STATUS REV K K K K K K K K K K K K K K OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Gary Zahn STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 CHECKED BY Michael C. Jones http://www.landandmaritime.dla.mil/ APPROVED BY Gregory A. Lude DRAWING APPROVAL DATE 92-07-08 REVISION LEVEL K MICROCIRCUIT, HYBRID, DIGITAL, MULTICHIP, DUAL CHANNEL, DRIVER-RECEIVER SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-92061 27 5962-E100-13 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 92061 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) X Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type 01 02 03 04 05 06 07 08 09 10 Generic number MR63147M MR63147M-2 NHI-1559, NHI-1567, NHI-1573, NHI-1579 NHI-1560, NHI-1568, NHI-1574, NHI-1580 NHI-1563, NHI-1569, NHI-1578, NHI-1593 NHI-1570, NHI-1577, NHI-1581, NHI-1594 ACT4458-201 ACT4464-201 ACT4460-201 ACT4454-201 Circuit function +5 V, dual channel, MIL-STD-1553 transceiver (Harris interface) +5 V, dual channel, MIL-STD-1553 transceiver (Smith interface) +5 V, dual channel, MIL-STD-1553 transceiver (standby low) +5 V, dual channel, MIL-STD-1553 transceiver (standby high) +5 V, dual channel, MacAir transceiver (standby low) +5 V, dual channel, MacAir transceiver (standby high) +5 V, dual channel, MIL-STD-1553 transceiver (standby low) +5 V, dual channel, MIL-STD-1553 transceiver (standby high) +5 V, dual channel, MacAir transceiver (standby low) +5 V, dual channel, MacAir transceiver (standby high) 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 2 E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter M N T U X Y Z 6 4 5 Descriptive designator See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 Terminals Package style 20 20 36 36 36 36 24 24 36 36 Dual-in-line Flat pack Dual-in-line Flat pack Dual-in-line Flat pack Micro flat pack Micro flat pack Dual-in-line (ceramic) Flat pack (ceramic) 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) ........................................................ Logic input voltage range .......................................................... Receiver differential input voltage .............................................. Driver peak output current ......................................................... Power dissipation (PD), device types 01 and 02: Hottest die (100% duty cycle) ................................................. Total hybrid (standby) ............................................................. Total hybrid (100% duty cycle) ............................................... Power dissipation (PD), device types 03 through 06: Hottest die (100% duty cycle) ................................................. Total hybrid (standby) ............................................................. Total hybrid (100% duty cycle) ............................................... Power dissipation (PD), device types 07 through 10: Total hybrid (standby) ............................................................. Total hybrid (100% duty cycle) ............................................... Storage temperature range ........................................................ Lead temperature (soldering, 10 seconds) ................................ Junction temperature (TJ) .......................................................... Thermal resistance, junction-to-case (θJC): Device types 01 through 06 .................................................... Device types 07 through 10 .................................................... Thermal resistance, junction-to-air (θCA) .................................... 1/ -0.3 V dc to +7.0 V dc -0.3 V dc to +5.5 V dc 10 VP-P +1.0 A 2.2 W 500 mW 2.46 W 500 mW 450 mW 950 mW 100 mW 2W -65°C to +150°C +300°C +135°C 4°C/W (hottest die) 5°C/W 20°C/W (still air) Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 3 1.4 Recommended operating conditions. Supply voltage range (VCC): Device types 01, 02, 07, 08, 09, and 10 .............................. Device types 03, 04, 05, and 06 .......................................... Logic input voltage range ...................................................... Receiver differential voltage ................................................... Driver peak output current ...................................................... Maximum serial data rate ....................................................... Case operating temperature range (TC).................................. +4.75 V dc to +5.25 V dc +4.5 V dc to +5.5 V dc 0 V dc to +5.0 V dc 8.0 VP-P +700 mA 0 Hz to 1.0 MHz -55°C to +125°C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Timing waveforms. The timing waveforms shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 4 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max RECEIVER Output low voltage Output high voltage VOL VOH Differential input level VI Input common-mode voltage VICM Differential input resistance RIN IOL = 4.0 mA 1,2,3 IOH = -0.4 mA 1,2,3 01,02 0.65 03,04, 05,06 0.4 07,08, 09,10 0.5 01,02, 07,08, 09,10 2.5 03,04, 05,06 2.7 4,5,6 All 4/ 4,5,6 All -5 1 MHz sine wave 4/ 4,5,6 01,02 2 03,04, 05,06 4 07,08, 09,10 20 V 8 VP-P +5 V-pk kΩ Input capacitance CIN 1 MHz sine wave 4/ 4,5,6 All 10 Threshold voltage VTH 1 MHz sine wave 5/ 4,5,6 All Receiver delay tDR From input zero crossing to DATA or DATA, See figure 3 9,10,11 01,02 600 03,04, 05,06 450 07,08, 09,10 500 0.56 V 1.2 pF V ns RECEIVER STROBE Input low voltage VSIL 1,2,3 All 0.7 V See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max RECEIVER STROBE- Continued. Input high voltage VSIH Input low current ISIL Input high current Strobe delay ISIH tDS VSIL = 0.4 V VSIH = 2.7 V 1,2,3 All 2.0 V 1,2,3 01,02 -1.1 mA 03-10 -0.4 1,2,3 From strobe rising or falling edge to DATA or DATA, See figure 3 9,10,11 01,02, 07,08, 09,10 40 03-06 20 01,02 200 03-06 40 07-10 100 µA ns TRANSMITTER Input low voltage VIL 1,2,3 All Input high voltage VIH 1,2,3 All 2.0 V Input low current IIL 1,2,3 01,02 -1.1 mA 03-10 -0.4 Input high current Differential output voltage IIH VO VIL = 0.4 V VIH = 2.7 V 1,2,3 4,5,6 35Ω load 140Ω load 0.7 01,02, 07,08, 09,10 40 03-06 20 01,02, 07,08, 09,10 6 9 03-06 7 9 01,02, 07,08, 09,10 24 36 03-06 28 36 V µA VP-P See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max TRANSMITTER - Continued. Differential output noise VON Inhibited 4/ 4,5,6 All Differential output resistance ROUT Transmitter off 4/ 4,5,6 01-06 10 07-10 2 6/ Output impedance ROUT When transmitting 4/ 4,5,6 7/ Output capacitance COUT 1 MHz sine wave 4/ 4,5,6 7/ Differential offset voltage VOS 4,5,6 35Ω load 8/ Vwd 35Ω load 10/ Rise time tr 35Ω load, see figure 3 Fall time tf Rise time tr Fall time tf Driver delay tDT 9,10,11 kΩ 10 09,10 40 01-06 15 07-10 15 All 4,5,6 35Ω load 9/ mVP-P 05,06 -90 +90 -360 +360 01,02 -1 +1 03-10 -0.1 +0.1 140Ω load 8/ Waveform distortion 10 01-04, 07,08 100 300 35Ω load, see figure 3 01-04, 07,08 100 300 10% to 90%, see figure 3 05,06 220 300 09,10 200 300 05,06 220 300 09,10 200 300 10% to 90%, see figure 3 TX DATA in to TX DATA out, see figure 3 9,10,11 01,02 450 03-06 150 07,08 250 09,10 400 Ω pF mVpk Vpeak ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max TRANSMITTER - Continued. Output harmonic content (referenced to the average peal value at 1.0 MHz) f = 1.5 MHz 3/ 9,10,11 05,06, 09,10 -3 dB f = 2.5 MHz 3/ -13.5 f = 4.0 MHz 3/ -25.5 TRANSMITTER INHIBIT Input low voltage VIIL Input high voltage VIIH Input low current IIIL Input high current Inhibit delay IIIH tDI-H tDI-L 1,2,3 All 0.7 V 2.0 VIIL = 0.4 V VIIH = 2.7 V Inhibited output, see figure 3 9,10,11 Active output, see figure 3 01,02 -1.1 03-10 -0.4 mA 01,02, 07-10 40 03-06 20 01,02, 07-10 450 03-06 150 01,02 250 03-06 150 07-10 450 01,02 55 03-06 45 07-10 30 µA ns POWER SUPPLY Supply current ICC1 Standby, data applied, inhibit high 1,2,3 mA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Device types Limits Min Unit Max POWER SUPPLY - Continued. Supply current ICC2 ICC3 ICC4 ICC5 25% duty cycle at 1 MHz 11/ 4,5,6 01,02 300 03-10 195 01,02 500 03-06 325 07-10 345 01,02 800 03-06 625 100% duty cycle at 1 MHz 11/ 07-10 750 80% duty cycle at 1 MHz 01,02 800 03-06 600 50% duty cycle at 1 MHz 11/ 100% duty cycle at 500 kHz 75% duty cycle at 1 MHz 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 10/ 11/ mA VCC = +5.0 V dc ±0.1 V dc, unless otherwise specified. All specifications and limits are for a single channel with no connections made to the other channel. Device types 03, 04, 05, 06, 07, 08, 09, and 10 are fully compliant to MIL-STD-1553 electrical specification. Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. Threshold determined by first missing word of a 33 word transmission to a 15530 CMOS Manchester encoder-decoder. When measured from 75 kHz to 1 MHz at transformer secondary with transformer self impedance of 3 kohms minimum, power on/off. When measured from 75 kHz to 1 MHz at transformer secondary. Offset is measured 2.5 µs after the mid-bit zero crossing of the last parity bit of a 660 µs transmission. This parameter exceeds the limits as indicated in MIL-STD-1553 for device types 01 and 02. The limits for device types 03, 04, 05, 06, 07, 08, 09, and 10 fully complies to MIL-STD-1553. For device types 07, 08, 09, and 10 the maximum supply currents are with respect to a 2.5:1 transformer. Frequency equals 1 MHz. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 10 Case outline M. Symbol A b b2 c D D1 e E eA L Q Millimeters Min Max 2.49 3.10 0.41 0.51 1.27 TYP Inches Min Max .098 .122 .016 .020 .050 TYP 0.20 25.15 .008 .990 0.30 25.65 .012 1.010 22.61 23.11 2.54 BSC 7.29 7.70 .890 .910 .100 BSC .303 .287 7.37 3.81 7.87 .290 .150 .310 0.64 1.14 .025 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 11 Case outline N. Symbol A b c D D1 E L Q Millimeters Min Max 1.27 1.78 0.41 0.51 0.20 0.30 25.15 25.65 22.61 23.11 7.37 7.87 10.16 2.49 3.43 Inches Min Max .050 .070 .016 .020 .008 .012 .990 1.010 .890 .910 .290 .310 .400 .098 .135 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 12 Case outline T. Symbol A b D D1 D2 E E1 e eA L R1 R2 Millimeters Min Max 4.45 4.95 0.41 0.51 48.01 48.51 43.05 43.31 2.29 2.79 19.56 20.07 2.03 2.54 2.54 BSC 14.99 15.49 6.35 2.18 TYP 1.40 TYP Inches Min Max .175 .195 .016 .020 1.890 1.910 1.695 1.705 .090 .110 .770 .790 .080 .100 .100 BSC .590 .610 .250 .086 TYP .055 TYP NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 13 Case outline U. Symbol A b c D D1 e E L Q Millimeters Min Max 3.81 4.32 0.30 0.51 0.20 0.30 48.01 48.51 48.05 43.31 2.54 BSC 19.56 20.07 10.16 1.78 2.29 Inches Min Max .150 .170 .012 .020 .008 .012 1.890 1.910 1.695 1.705 .100 BSC .770 .790 .400 .070 .090 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 14 Case outline X. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 15 Case outline Y. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 16 Case outline Z. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 17 Case outline 6. Inches .001 .003 .005 .010 .018 .050 .056 mm 0.03 0.08 0.13 0.25 0.46 1.27 1.42 Inches .075 .087 .100 .102 .110 .125 .140 .240 mm 1.91 2.21 2.54 2.59 2.79 3.18 3.56 6.10 Inches .400 .550 .596 .600 .778 .808 1.700 1.899 mm 10.16 13.97 15.14 15.24 19.76 20.53 43.18 48.23 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for general information only. 3. Unless otherwise specified, tolerance for three place decimals shall be ±.005 (0.013 mm). 4. Case outline X, leads are bottom brazed to the package. 5. Case outlines Y, Z and 6 may be supplied with a ceramic tiebar beyond the .400 inches (10.16 mm) lead dimension, to hold leads in place. Finished lead length visual acceptance criteria for solder dip apply to the leads up to .400 inches (10.16 mm). The lead spacing measured shall be no less than .400 inches (10.16 mm) from edge of package. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 18 Case outline 4. Symbol A b b2 c D D1 e E eA L Q Millimeters Min Max 3.56 0.41 1.23 0.20 46.61 0.51 1.32 0.30 47.37 43.18 2.54 BSC 14.78 15.19 14.99 15.49 3.81 1.02 1.52 Inches Min Max .140 .016 .048 .008 1.835 .020 .052 .012 1.865 1.700 .100 BSC .582 .598 .590 .610 .150 .040 .060 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 19 Case outline 5. Symbol A b c D D1 e E L Q Millimeters Min Max 2.74 3.35 Inches Min Max .108 .132 0.41 0.20 46.61 .016 .008 1.835 0.51 0.30 47.37 43.18 2.54 BSC 14.99 15.49 12.70 1.78 2.29 .020 .012 1.865 1.700 .100 BSC .590 .610 .500 .070 .090 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 20 Device types 03 through 06 Case outlines M and N All 01 through 10 X and Y (Device types 01 and 02). U, T, 4, and 5 (Device types 03 through 06). Terminal number Terminal symbol Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 +5 V dc (VCC) BUS_A BUS_A_L RXENA_A GND_A +5 V dc (VCC) BUS_B BUS_B_L RXENA_B GND_B RXB_L RXB TXINH_B TX_B TXB_L RXA_L RXA TXINH_A TXA TXA_L --------------------------------- A A A A A B B B B B B B B B B A A A A A --------------------------------- Terminal Symbol TX DATA out TX DATA out GND NC RX DATA out Strobe GND RX DATA out GND (case) TX DATA out TX DATA out GND NC RX DATA out Strobe GND RX DATA out NC NC RX DATA in RX DATA in GND NC +5 V dc (VCC) Inhibit TX DATA in TX DATA in NC RX DATA in RX DATA in GND NC +5 V dc (VCC) Inhibit TX DATA in TX DATA in Z Channel One One One One One One One One Two Two Two Two Two Two Two Two Two Two Two Two Two Two One One One One One One One Terminal symbol TX DATA out/RX DATA in TX DATA out/RX DATA in GND RX DATA out Strobe RX DATA out TX DATA out/RX DATA in TX DATA out/RX DATA in GND RX DATA out Strobe RX DATA out GND +5 V dc (VCC) GND Inhibit TX DATA in TX DATA in GND +5 V dc (VCC) GND Inhibit TX DATA in TX DATA in ------------------------- Channel One One One One One One Two Two Two Two Two Two Two Two Two Two Two Two One One One One One One ------------------------- FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 21 Device types 01, 03, and 07. NOTE: Both inputs "TX DATA in" and "TX DATA in" must be in the same logic states during off times. FIGURE 3. Timing waveforms. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 22 Device types 02, 04, and 08. NOTE: Both inputs "TX DATA in" and "TX DATA in" must be in the same logic states during off times. FIGURE 3. Timing waveforms - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 23 Device types 05 and 09. NOTE: Both inputs "TX DATA in" and "TX DATA in" must be in the same logic states during off times. FIGURE 3. Timing waveforms - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 24 Device types 06 and 10. NOTE: Both inputs "TX DATA in" and "TX DATA in" must be in the same logic states during off times. FIGURE 3. Timing waveforms - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 25 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 3, 6, 11 Final electrical parameters 1*,2,3,4,5,6,9,10,11 Group A test requirements 1,2,3,4,5,6,9,10,11 Group C end-point electrical parameters 1,2,3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 26 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92061 A REVISION LEVEL K SHEET 27 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 13-01-22 Approved sources of supply for SMD 5962-92061 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9206101HXA 5962-9206101HYA 5962-9206101HZA 5962-9206102HXA 5962-9206102HYA 5962-9206102HZA 3/ 3/ 3/ 3/ 3/ 3/ MR63147MPS MR63147MFS MR63147MFM MR63147MPS-2 MR63147MFS-2 MR63147MFM-2 5962-9206103HMA 5962-9206103HMC 5962-9206103HNA 5962-9206103HNC 5962-9206103HTA 5962-9206103HTC 5962-9206103HUA 5962-9206103HUC 5962-9206103HZA 5962-9206103HZC 5962-9206103H4A 5962-9206103H4C 5962-9206103H5A 5962-9206103H5C 5962-9206103H6A 5962-9206103H6C 27851 27851 27851 27851 27851 27851 27851 27851 3/ 3/ 27851 27851 27851 27851 27851 27851 NHI-1567/883 NHI-1567/883 NHI-1567FP/883 NHI-1567FP/883 NHI-1559/883 NHI-1559/883 NHI-1559FP/883 NHI-1559FP/883 NHI-1573FP/883 NHI-1573FP/883 NHI-1579/883 NHI-1579/883 NHI-1579FP/883 NHI-1579FP/883 NHI-1573FP/883 NHI-1573FP/883 5962-9206104HMA 5962-9206104HMC 5962-9206104HNA 5962-9206104HNC 5962-9206104HTA 5962-9206104HTC 5962-9206104HUA 5962-9206104HUC 5962-9206104HZA 5962-9206104HZC 5962-9206104H4A 5962-9206104H4C 5962-9206104H5A 5962-9206104H5C 5962-9206104H6A 5962-9206104H6C 27851 27851 27851 27851 27851 27851 27851 27851 3/ 3/ 27851 27851 27851 27851 27851 27851 NHI-1568/883 NHI-1568/883 NHI-1568FP/883 NHI-1568FP/883 NHI-1560/883 NHI-1560/883 NHI-1560FP/883 NHI-1560FP/883 NHI-1574FP/883 NHI-1574FP/883 NHI-1580/883 NHI-1580/883 NHI-1580FP/883 NHI-1580FP/883 NHI-1574FP/883 NHI-1574FP/883 1 of 3 STANDARD MICROCIRCUIT DRAWING BULLETIN - CONTINUED. DATE: 13-01-22 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9206105HMA 5962-9206105HMC 5962-9206105HNA 5962-9206105HNC 5962-9206105HTA 5962-9206105HTC 5962-9206105HUA 5962-9206105HUC 5962-9206105HZA 5962-9206105HZC 5962-9206105H4A 5962-9206105H4C 5962-9206105H5A 5962-9206105H5C 5962-9206105H6A 5962-9206105H6C 27851 27851 27851 27851 27851 27851 27851 27851 3/ 3/ 27851 27851 27851 27851 27851 27851 NHI-1569/883 NHI-1569/883 NHI-1569FP/883 NHI-1569FP/883 NHI-1563/883 NHI-1563/883 NHI-1563FP/883 NHI-1563FP/883 NHI-1593FP/883 NHI-1593FP/883 NHI-1578/883 NHI-1578/883 NHI-1578FP/883 NHI-1578FP/883 NHI-1593FP/883 NHI-1593FP/883 5962-9206106HMA 5962-9206106HMC 5962-9206106HNA 5962-9206106HNC 5962-9206106HTA 5962-9206106HTC 5962-9206106HUA 5962-9206106HUC 5962-9206106HZA 5962-9206106HZC 5962-9206106H4A 5962-9206106H4C 5962-9206106H5A 5962-9206106H5C 5962-9206106H6A 5962-9206106H6C 27851 27851 27851 27851 27851 27851 27851 27851 3/ 3/ 27851 27851 27851 27851 27851 27851 NHI-1570/883 NHI-1570/883 NHI-1570FP/883 NHI-1570FP/883 NHI-1577/883 NHI-1577/883 NHI-1577FP/883 NHI-1577FP/883 NHI-1594FP/883 NHI-1594FP/883 NHI-1581/883 NHI-1581/883 NHI-1581FP/883 NHI-1581FP/883 NHI-1594FP/883 NHI-1594FP/883 5962-9206107HZA 5962-9206107HZC 88379 88379 ACT4458-201-2 ACT4458-201-1 5962-9206108HZA 5962-9206108HZC 88379 88379 ACT4464-201-2 ACT4464-201-1 5962-9206109HZA 5962-9206109HZC 88379 88379 ACT4460-201-2 ACT4460-201-1 5962-9206110HZA 5962-9206110HZC 88379 88379 ACT4454-201-2 ACT4454-201-1 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source. 2 of 3 STANDARD MICROCIRCUIT DRAWING BULLETIN - CONTINUED. DATE: 13-01-22 Vendor CAGE number Vendor name and address 27851 Spectrum Microwave, Incorporated Division API Technologies RF Solutions-Spectrum Microwave 400 Nickerson Road Marlborough, MA 01752 88379 Aeroflex Plainview Incorporated, (Aeroflex Microelectronic Solutions) 35 South Service Road Plainview, NY 11803-4193 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 3 of 3