AS10515F16MIL

Quad Line Receiver
AS10515F16MIL
Quad Line Receiver
PIN ASSIGNMENT
(Top View)
AVAILABLE AS MILITARY
SPECIFICATIONS
16-Pin FlatPack (F)
• Military Equivalent Screening - 883 1.2.2
DIN\
COUT
DOUT
VCC2
VCC1
AOUT
BOUT
AIN\
GENERAL DESCRIPTION
The AS10515F16MIL is a quad differential amplifier designed for use in sensing differential signals over long lines.
The base bias supply (VBB) is made available at pin 9 to make
the device useful as a Schmitt trigger, or in other applications
where a stable reference voltage is necessary.
Active current sources provide the AS10515F16MIL with
excellent common mode noise rejection. If any amplifier in a
package is not used, one input of that amplifier must be connected to VBB (pin 9) to prevent upsetting the current source
bias network.
• PD = 150mW Max/Pkg (No Load)
• tpd = 2.0ns typ
• tr, tf = 2.0ns type (20% - 80%)
FLATS
BURN-IN
(CONDITION C)
VCC1
AOUT
BOUT
AIN\
AIN
BIN
BIN\
VEE
VBB
CIN\
CIN
DIN
DIN\
COUT
DOUT
VCC2
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
GND
51 Ω to VTT
51 Ω to VTT
VBB
AS10515F16MIL
Rev. 2.2 01/10
16
15
14
13
12
11
10
9
DIN
CIN
CIN\
VBB
VEE
BIN\
BIN
AIN
BURN-IN CONDITIONS:
VTT = -2.0V MAX/ -2.2V MIN
VEE = -5.7V MAX/ -5.2V MIN
VBB = All pins designated for VBB must be tied together, no
external voltage applied.
NOTES
1. VBB to be used to supply bias to the AS10515F16MIL only and
bypassed (when used) with 0.01 μF to 0.1 μF capacitor.
2. When the input pin with the bubble goes positive, the output goes
negative.
PIN ASSIGNMENTS
FUNCTION
1
2
3
4
5
6
7
8
LOGIC DIAGRAM
GND
GND
VBB
VEE
VBB
VBB
GND
GND
VBB
51 Ω to VTT
51 Ω to VTT
GND
4
5
2
6
7
3
10
11
14
12
13
15
VBB
9
For more products and information
please visit our web site at
www.micross.com
Micross Components reserves the right to change products or specifications without notice.
1
Quad Line Receiver
AS10515F16MIL
VCC = 2.0V ± 0.005V
Channel A
Coax A
Channel B
Coax B
0.1 μF
± 20%
25 μF
± 20%
R1
*Pulse
Generator
Input
CL
D.U.T.
Coax
R1 = 50 Ω resistor in series with
a 50 Ω coax cable constituting
the 100 Ω load.
*Pulse Generator must be capable of
rise and fall times of 2.0ns ± 0.2ns.
0.1 μF ±20%
NOTES:
1. tr = tf = 2.0ns ±0.2ns measured at (20% - 80%)
VEE = -3.2V ±0.005V
2. PW > 20ns
3. PRF = 1.0 MHz
4. R1 = 50 Ω resistor in series with 50 Ω coax constituting the 100 Ω load.
5. Unused outputs should be loaded 100 Ω to ground.
6. 2:1 divider may be used.
tr
VIN
80%
50%
20%
tf
PS1
80%
50%
20%
PS2
> 20ns
tTLH
VOUT
VOUT\
tTHL
80%
50%
20%
80%
50%
20%
tPLH
tPHL
tPHL
tPLH
80%
50%
20%
80%
50%
20%
tTHL
tTLH
Figure 1. Switching Test Circuit and Waveforms
AS10515F16MIL
Rev. 2.2 01/10
Micross Components reserves the right to change products or specifications without notice.
2
AS10515F16MIL
Rev. 2.2 01/10
3
Input Leakage
Current
-1.82
-1.92
-0.63
-0.88
TA = 125°C
TA = -55°C
-1.60
-1.85
-1.0
-26
95
-1.23
-0.78 -0.845 -0.63
-0.95
-1.35
-1.62
-1.85
-1.08
-0.88
-0.88
-1.0
-29
-1.24
165
-1.12
-1.5
-29
-1.44
165
-1.32
-1.82 -1.525 -1.92 -1.635
-1.10
-1.82 -1.545 -1.92 -1.655
-0.78 -0.825 -0.63
-0.93
μA
μA
mA
V
V
V
V
V
VIL1
4, 7, 10, 13 5, 6, 11, 12
4-7
10 - 13
PS1
-1.255 -1.510 +1.01
-1.000 -1.400 +1.24
-1.105 -1.475 +1.11
VIL2
+0.28
+0.36
+0.31
PS2
-3.2
-3.2
-3.2
VEEL
-5.2
-5.2
-5.2
VEE
VIL2
4, 7, 10, 13 5, 6, 11, 12
5, 6, 11, 12 4, 7, 10, 13
VIH2
8
8
8
8
8
8
8
8
VEE
1, 16
1, 16
1, 16
1, 16
1, 16
1, 16
1, 16
1, 16
VCC
4-7
10 - 13
***
4-7
11 - 13
4-7
11 - 13
4-7
11 - 13
4-7
11 - 13
5, 6
11, 12
5, 6
11, 12
Pinouts referenced are for F package, check Pin Assignments
VCC = 0V, Output Load = 100 Ω to -2.0V
5, 6, 11, 12 4, 7, 10, 13
VIH1
-1.85
-0.78
TA = 25°C
VIH2
Test Voltage Values (Volts)
TEST VOLTAGE APPLIED TO PINS BELOW:
VIL1
VIH1
Test
Temperature
LIMITS
UNITS
+25°C
+125°C
-55°C
Subgroup 1 Subgroup 2 Subgroup 3
MIN MAX MIN MAX MIN MAX
** Connected to pin 9.
*** Measure voltage on pin 9 while it is connected to other pins.
ICBO
IIH
IEE
**VBB
VOL1
VOH1
VOL
VOH
High Output
Voltage
Low Output
Voltage
High Output
Voltage
Low Output
Voltage
Reference
Voltage
Power Supply
Current
Input Current
High
Functional
Parameters:
SYMBOL PARAMETER
* ELECTRICAL CHARACTERISTICS
Each MECL 10K series circuit has been designed to meet the
dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket
or mounted on a printed circuit board and transverse air flow
greater than 500 linear fpm is maintained. Outputs are terminated through a 100 Ω resistor to -2.0 volts.
QUIESCENT LIMIT TABLE*
4-7
10 - 13
4-7
10 - 13
8
9
2, 3 ,14, 15
2, 3 ,14, 15
2, 3 ,14, 15
2, 3 ,14, 15
P.U.T.
-5.2
-5.2
-5.2
VCB
Quad Line Receiver
AS10515F16MIL
Micross Components reserves the right to change products or specifications without notice.
AS10515F16MIL
Rev. 2.2 01/10
4
tPLH
1.0
1.0
1.1
Fall Time
tTHL
Propagation Delay
High to Low
Propagation Delay
Low to High
1.1
tPHL
-1.82
-1.92
-0.63
-0.88
TA = 125°C
TA = -55°C
2.90
2.9
3.3
3.3
1.0
1.0
1.0
1.0
4.0
4.0
4.4
4.4
1.0
1.0
1.0
1.0
3.5
3.5
3.9
3.9
ns
ns
ns
ns
VIL2
PS1
PS2
+0.28
+0.36
+0.31
-3.2
-3.2
-3.2
VEEL
-5.2
-5.2
-5.2
VEE
-5.2
-5.2
-5.2
VCB
TEST VOLTAGE APPLIED TO PINS BELOW:
-1.255 -1.510 +1.01
-1.000 -1.400 +1.24
-1.105 -1.475 +1.11
VIH2
Test Voltage Values (Volts)
VOUT
4, 7, 11, 13 2, 3, 14, 15
4, 7, 11, 13 2, 3, 14, 15
4, 7, 11, 13 2, 3, 14, 15
4, 7, 11, 13 2, 3, 14, 15
VIN
1, 16
1, 16
1, 16
1, 16
VCC
8
8
8
8
VEEL
2, 3 ,14, 15
2, 3 ,14, 15
2, 3 ,14, 15
2, 3 ,14, 15
P.U.T.
Pinouts referenced are for F package, check Pin Assignments
VCC = 2.0V, Output Load = 100 Ω to GND
VIL1
-1.85
VIH1
-0.78
TA = 25°C
Test
Temperature
UNITS
LIMITS
+125°C
-55°C
+25°C
Subgroup 9 Subgroup 10 Subgroup 11
MIN MAX MIN MAX MIN MAX
Rise Time
Functional
Parameters:
PARAMETER
tTLH
SYMBOL
* ELECTRICAL CHARACTERISTICS
Each MECL 10K series circuit has been designed to meet the
dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket
or mounted on a printed circuit board and transverse air flow
greater than 500 linear fpm is maintained. Outputs are terminated through a 100 Ω resistor to -2.0 volts.
QUIESCENT LIMIT TABLE*
Quad Line Receiver
AS10515F16MIL
Micross Components reserves the right to change products or specifications without notice.