BL8573 500mA/1.5A Standalone Linear Li-Ion Battery Charge DESCRIPTION FEATURES The BL8573 is a single cell, fully integrated constant current (CC)/constant voltage (CV) Li-ion battery charger. Its compact package with minimum external components requirement makes the BL8573 ideal for portable applications. • • • No external sense resistor or blocking diode is necessary for the BL8573. Build-in thermal feedback mechanism regulates the charge current to control the die temperature during high power operation or at elevated ambient temperature. • • The BL8573 has a pre-charge function for trickle charging deeply discharged batteries. The fast charge current can be programmed by an external resistor. CV regulation mode is automatically enabled once the battery’s charging curve reaches the constant voltage portion. The output current then decays and is finally terminated once the charge current drops to 1/10th of the programmed value. The BL8573 keeps monitoring the battery voltage and enables a new charge cycle once the voltage drops by 150mV below the CV value. • • • • • • • • APPLICATIONS Power supply state is constantly monitored and the battery drain current is reduced to minimum value automatically when the BL8573 senses a lack of input power. In its shutdown mode, the BL8573 can reduce the supply current to less than 25μA. A status pin outputs a logic HIGH/LOW to indicate the charging status and the presence of power supply. • • • Other features include charge current monitor, under-voltage lockout. TYPICAL APPLICATION BL857 BL8573 www.belling.com.cn Standalone Capability with no Requirement of External MOSFET, Sense Resistor or Blocking Diode. Complete Linear Charger in Compact Package for Single Cell Lithium-Ion Batteries Programmable Pre-charge, Fast Charge and Termination Current. Constant-Current/Constant-Voltage Operation with Thermal Regulation to Maximize Charge Rate Without Risk of Overheating Charges Single Cell Li-Ion Batteries Directly from USB Port Preset 4.2V Charge Voltage with ±1% Accuracy Automatic Recharge Charge Status Output Pin C/10 Charge Termination 25µA Supply Current in Shutdown 2.9V Trickle Charge Threshold Soft-Start Limits Inrush Current Available in SOT-23-6 and ESOP8 Package 1 Cellular Telephones, PDAs, MP3 Players Charging Docks and Cradles Bluetooths Applications BL8573 ORDERING INFORMATION BL8573 □ 1□ 2□ 3 Code 1 □ 2 □ 3 □ PIN CONFIGURATION Product Classification Description BL8573CB6TR Marking Temperature&Rohs: C:-40~85°C ,Pb Free Rohs Std. Package type: B6:SOT-23-6 S8: ESOP-8 Packing type: TR:Tape&Reel (Standard) B1:Product Code B1YW YW:Data Code Product Classification LL: Lot No. BL8573CS8TR ESOP-8 LLHYW H: Fab code YW: Date code Note：Y: The Year of manufacturing,”1” stands for year 2011,”2” stands for year 2012,and “8” stands for year 2018. W: The week of manufacturing. ”A” stands for week 1,”Z” stands for week 26,” A ” stands for week 27,” Z ” stands for week 52. BLOCK DIGRAM www.belling.com.cn 2 BL8573 PIN DESCRIPTION : Open-Drain Charge Status Output. The pin outputs low when the battery is CHRG charging. STDBY: Open-Drain Charge Status Output. The STDBY pin outputs low when the battery is full. PROG: Program, Monitor the charge current and Shutdown. This pin set to 1V in constant-current mode. The charge current is programmed by connecting a 1% resistor, RPROG, to GND pin. The charge current can be calculated using the following formula: GND: Ground. I BAT = (VPROG / RPROG ) ⋅1000 BAT: Charge Current Output. This pin provides charge current to the battery and regulates the final float voltage to 4.2V which is set by an internal precision resistor divider. The PROG pin can also be used to switch the charger to shutdown mode by disconnecting the program resistor from ground. This results in a 3μA current to pull the PROG pin to a high level shutdown threshold voltage, thus stop the charging and reduce the supply current to 25μA. This pin is also clamped to approximately 2.4V. A higher voltage beyond this value will draw currents as high as 1.5mA. Device normal operation can be resumed by reconnecting the RPROG resistor to ground. VCC: Positive Input Supply. Needs to be bypassed with at least a 1μF capacitor. When input voltage drops to within 30mV of the BAT pin voltage, the BL8573 switches to shutdown mode. ABSOLUTE MAXIMUM RATING VCC PROG BAT CHRG STDBY BAT Short-Circuit Duration PROG Pin Current Maximum Junction Temperature Operating Ambient Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 sec) –0.3V to 6.5V – 0.3V to VCC + 0.3V –0.3V to 5V –0.3V to 6.5V –0.3V to 6.5V Continuous 2mA 125°C –40°C to 85°C –40°C to 125°C 260°C Note: Exceed these limits to damage to the device. Exposure to absolute maximum rating conditions may affect device reliability. www.belling.com.cn 3 BL8573 ELECTRICAL CHARACTERISTICS VCC=5V, Ta=25°C, RPROG=10K, unless otherwise noted. SYMBOL VCC PARAMETER CONDITIONS Input Supply Voltage MIN TYP MAX UNITS 4.25 6.0 V 2000 500 μA μA 50 μA ITERM Charge Mode (Note 2) 300 Standby Mode (Charge Terminated) 200 Input Supply Current Shutdown Mode (RPROG Not Connected, 25 VCC<VBAT, or VCC<VULO) Regulated Output (Float) Voltage IBAT = 40mA 4.158 4.2 Current Mode 93 100 RPROG = 2K, Current Mode 465 500 BAT Pin Current Standby Mode, VBAT = 4.2V 0 -2.5 Shutdown Mode (RPROG Not Connected) 1 Sleep Mode, VCC = 0V 1 Trickle Charge Current VBAT < VTRIKL, RPROG = 2K 20 45 Trickle Charge Threshold Voltage VBAT Rising 2.8 2.9 Trickle Charge Hysteresis Voltage 60 80 VCC Undervoltage Lockout Threshold From VCC Low to High 2.7 2.8 VCC Undervoltage Lockout Hysteresis 150 200 PROG Pin Rising 1.15 1.21 Manual Shutdown Threshold Voltage PROG Pin Falling 0.9 1 VCC from Low to High 70 100 VCC–VBAT Lockout Threshold Voltage VCC from High to Low 5 30 C/10 Termination Current Threshold Note 3 0.085 0.1 4.242 107 535 -6 5 5 70 3 110 2.92 300 1.30 1.1 140 50 0.115 V mA mA μA μA μA mA V mV V mV V V mV mV mA VPROG PROG Pin Voltage Current Mode, VBAT=4V 1 1.07 V VCHRG CHRG Pin Output Low Voltage ICHRG = 5mA 0.35 0.6 V VRECHRG Recharge BAT Threshold Voltage Junction Temperature in Constant Temperature Mode Power FET “ON” Resistance (Between VCC and BAT) Soft-Start Time Recharge Comparator Filter Time Termination Comparator Filter Time PROG Pin Pull-Up Current VFLOAT - VRECHRG 150 200 mV ICC VFLOAT IBAT ITRIKL VTRIKL VTRHYS VUV VUVHYS VMSD VASD TLIM RON tss tRECHARGE tTERM IPROG IBAT = 0 to IBAT =1000V/RPROG VBAT High to Low IBAT Falling Below ICHG/10 0.93 100 120 °C 0.25 Ω 100 0.5 5 20 400 1000 2500 3 μs ms μs μA Note2 : Supply current includes PROG pin current (approximately 100μA) but does not include any current delivered to the battery through the BAT pin (approximately 100mA). Note3 : ITERM is expressed as a fraction of measured full charge current with indicated PROG resistor. www.belling.com.cn 4 BL8573 TYPICAL PERFORMANCE CHARACTERISTICS (Vcc=5V, Ta=25°C, unless otherwise noted.) Charge Current VS. Supply Voltage Vbat=4.0V 2.0 2.0 1.8 1.8 1.6 1.6 Charge Current(A) Charge Current(A) Charge Current VS. Battery Voltage Vcc=4.5V 1.4 1.2 1.0 0.8 0.6 0.4 1.2 1.0 0.8 0.6 0.4 Rprog=680ohm Rprog=510ohm 0.2 1.4 Rprog=680ohm Rprog=510ohm 0.2 0.0 0.0 2.5 3.0 3.5 4.0 4.5 4.0 4.5 5.0 5.5 Vbat(V) Vcc(V) Charge Current vs PROG Pin Voltage Regulated Voltage vs Supply Voltage 6.0 4.4 500 450 400 4.3 Vfloat(V) Ibat(mA) 350 300 250 200 150 4.2 4.1 100 Ibat=40mA Rprog=2K 50 0 4.0 0 0.2 0.4 0.6 0.8 4.0 1 4.5 5.0 Vprog (V) PROG Pin Current vs PROG Pin Voltage (Pul-Up Current) 6.0 PROG Pin Current vs PROG Pin Voltage (Clamp Current) 3.0 0 2.5 -100 Iprog(μA) Iprog(μA) 5.5 Vcc(V) 2.0 1.5 1.0 -200 -300 -400 -500 0.5 -600 0.0 -700 2.0 2.2 2.4 2.6 2.5 2.8 Vprog(V) www.belling.com.cn 3.5 4.5 Vprog(V) 5 5.5 BL8573 TYPICAL PERFORMANCE CHARACTERISTICS(CONTINUES) (Vcc=5V, Ta=25°C, unless otherwise noted.) Trickle Charge Voltage vs Temperature CHRG Pin Current vs CHRG Pin Voltage 3.1 16 14 3.0 Vtrickle (V) 12 Ichrg(mA) 10 8 6 4 2.9 2.8 2.7 2 2.6 0 0 1 2 3 4 5 -50 6 -25 0 Regulated Voltage vs Temperature 75 100 PROG Pin Voltage vs Temperature 1.2 4.3 1.1 Vprog (V) 4.4 4.2 1.0 0.9 4.1 0.8 4.0 -50 -25 0 25 50 75 -50 100 -25 0 25 50 75 100 T(°C) T(°C) IC Temperature vs Battery Voltage Recharge Voltage vs Temperature 90 4.2 Icharge=1.0A Icharge=1.2A Icharge=1.5A 80 4.1 70 T(℃） Vrecharge (V) 50 T(°C) Vchrg(V) Vfloat (V) 25 4.0 60 50 3.9 40 3.8 -50 -25 0 25 50 75 30 100 3 T(°C) www.belling.com.cn 3.4 3.8 Vbat(V) 6 4.2 BL8573 DETAILED DESCRIPTION The BL8573 is a single cell, fully integrated constant current(CC) /constant voltage (CV) Li-ion battery charger. It can deliver up to 1.5A of charge current with a final float voltage accuracy of ±1%. The BL8573 has a build-in thermal regulation circuitry that ensures its safe operation. No blocking diode or external current sense resistor is required; hence reduce the external components for a basic charger circuit to two. The BL8573 is also capable of operating from a USB power source. temperature is 45°C at certain power rating, BL8573 would have the same charge current and junction temperature as chips without STL function at room temperature. As the ambient temperature rises up to 55°C, a chip without STL would have 100°C of junction temperature, while BL8573 would reduce its charge current and hence the junction temperature would be much lower. The STL function helps to improve system reliability. CHARGE TERMINATION NORMAL CHARGE CYCLE The BL8573 keeps monitoring the PROG pin during the charging process. It terminates the charge cycle when the charge current falls to 1/10th the programmed value after the final float voltage is reached. When the PROG pin voltage falls below 100mV for longer than tTERM (typically 1ms), charging is terminated. The charge current is latched off and the BL8573 enters standby mode, where the input supply current drops to 200μA. (Note: C/10 termination is disabled in trickle charging and thermal limiting modes). The BL8573 initiates a charge cycle once the voltage at the VCC pin rises above the UVLO threshold level. A ±1% precision resistor needs to be connected from the PROG pin to ground. If the voltage at the BAT pin is less than 2.9V, the charger enters trickle charge mode. In this mode, the charge current is reduced to nearly 1/10 the programmed value until the battery voltage is raised to a safe level for full current charging. The charger switches to constant-current mode as the BAT pin voltage rises above 2.9V, the charge current is thus resumed to full programmed value. When the final float voltage (4.2V) is reached, the BL8573 enters constant-voltage mode and the charge current begins to decrease until it drops to 1/10 of the preset value and ends the charge cycle. During charging, the transient response of the circuit can cause the PROG pin to fall below 100mV temporarily before the battery is fully charged, thus can cause a premature termination of the charge cycle. A 1ms filter time (tTERM) on the termination comparator can prevent this from happening. Once the average charge current drops below 1/10th the PROGRAMMING CHARGE CURRENT The charge current is programmable by setting the value of a precision resistor connected from the PROG pin to ground. The charge current is 1000 times of the current out of the PROG pin. The program resistor and the charge current are calculated using the following equations: RPROG = 1000V I CHG The charge current out of the BAT pin can be determined at any time by monitoring the PROG pin voltage using the following equation: I BAT = V PROG ⋅ 1000 R PROG BL8573 has a self-temperature-limiting (STL) function, the chip starts to limit its charge current by reducing VPROG gradually after silicon temperature rises above 70°C. Say if the difference of junction and ambient www.belling.com.cn Figure 1. Charge Cycle Diagram 7 BL8573 programmed value, the BL8573 terminates the charge cycle and ceases to provide any current through the BAT pin. In this state, all loads on the BAT pin must be supplied by the battery. UNDERVOLTAGE LOCKOUT (UVLO) Build-in undervoltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above the undervoltage lockout threshold. The UVLO circuit has a built-in hysteresis of 200mV. Furthermore, to protect against reverse current in the power MOSFET, the UVLO circuit keeps the charger in shutdown mode if VCC falls to within 30mV of the battery voltage. If the UVLO comparator is tripped, the charger will not come out of shutdown mode until VCC rises 100mV above the battery voltage. The BL8573 constantly monitors the BAT pin voltage in standby mode and resume another charge cycle if this voltage drops below the recharge threshold (VRECHRG). User can also manually restart a charge cycle in standby mode either by removing and then reapplied the input voltage or restart the charger using the PROG pin. A diagram of typical charge cycle is shown in Figure 1. MANUAL SHUTDOWN ) CHARGE STATUS INDICATOR ( Floating the PROG pin by removing the resistor from PROG pin to ground can put the device in shutdown mode. The battery drain current is thus reduced to less than 5μA and the supply current to less than 50μA. Reconnecting the resistor back will restart a new charge cycle. There are two different states of the charge status output, namely pull-down and high impedance. The pull-down state indicates that the BL8573 is in a charge cycle. When the charge cycle has terminated, the pin state is then determined by undervoltage lockout conditions. If the difference between VCC and BAT pin voltage is less than 100mV or insufficient voltage is applied to the VCC pin, High impedance appears on the charge statues pin. The CHRG pin is in a high impedance state if the BL8573 is in undervoltage lockout mode. AUTOMATIC RECHARGE THERMAL LIMITING After the termination of the charge cycle, the BL8573 constantly monitors the BAT pin voltage and starts a new charge cycle when the battery voltage falls below 4.05V, keeping the battery at fully charged condition. output enters a pull-down state during recharge CHRG cycles. Build-in feedback circuitry mechanism can reduce the value of the programmed charge current once the die temperature tends to rise above 120°C, hence prevents the temperature from further increase and ensure device safe operation. APPLICATIONS INFORMATION above 100kHz to maintain device stability. Therefore, the maximum resistance value can be calculated from the following equation, CPROG is the capacitance loaded to the PROG pin STABILITY CONSIDERATIONS When a battery is connected to the output, the constant-voltage mode feedback is always stable. However, in the case of absence of battery, an output capacitor is recommended to reduce ripple voltage. In the case of high value capacitance or low ESR ceramic capacitors, a small value series resistor (~1Ω) is recommended. No series resistor is needed if tantalum capacitors are used. R PROG ≤ Average rather than instantaneous charge current is more of a concern. A simple low pass filter can be used on the PROG pin to measure the average battery current as shown in Figure 2. A 10K resistor has been added between the PROG pin and the filter capacitor to ensure stability. In constant-current mode, the PROG pin is in the feedback loop, thus its impedance affects the stability. The maximum allowed value of the program resistor is 20K, and additional capacitance reduces this value. The pole frequency at the PROG pin needs to be kept www.belling.com.cn 1 2π ⋅ 10 5 ⋅ C PROG 8 BL8573 I BAT = 120°C − 60°C 60°C = (5V − 3.75V ) ⋅ 150°C / W 187.5°C / A I BAT = 320 mA BL857 BL8573 Moreover, when thermal feedback reduces the charge current, the voltage at the PROG pin is also reduced proportionally as discussed in the operation section. Figure 2. Isolating Capacitive Load on PROG Pin and Filtering It is important to remember that BL8573 applications do not need to be designed for worst-case thermal conditions since the IC will automatically reduce power dissipation when the junction temperature reaches approximately 120°C. POWER DISSIPATION The power dissipated in the IC causes the rise of die temperature. Most of the power dissipation is caused by the internal power MOSFET, and can be calculated by the following equation: THERMAL CONSIDERATIONS Due to its compact size, it is of great importance to use a good thermal PC board. Good thermal conduction increases maximum allowed charge current value. PD = (VCC − VBAT ) ⋅ I BAT Where PD is the power dissipated, VCC is the input supply voltage, VBAT is the battery voltage and IBAT is the charge current. The approximate ambient temperature at which the thermal feedback begins to protect the IC is: The thermal path for the heat generated by the IC is from the die to the copper lead frame, through the package leads, (especially the ground lead) to the PC board copper. The PC board copper is the heat sink. The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient. Feed through vias to inner or backside copper layers are also useful in improving the overall thermal performance of the charger. Other heat sources on the board, not related to the charger, must also be considered when designing a PC board layout because they will affect overall temperature rise and the maximum charge current. TA = 120°C − PDθ JA TA = 120°C − (VCC − VBAT ) ⋅ I BAT ⋅ θ JA Example: An BL8573 operating from a 5V USB supply is programmed to supply 400mA full-scale current to a discharged Li-Ion battery with a voltage of 3.75V. θ Assuming JA is 150°C /W (see Board Layout Considerations), the ambient temperature at which the BL8573 will begin to reduce the charge current is approximately: INCREASING THERAML REGULATION CURRENT T A = 120 °C − (5V − 3 .75V ) ⋅ ( 400 mA ) ⋅ 150 °C / W Reducing the voltage drop across the internal MOSFET can significantly decrease the power dissipation in the IC. Minimized power dissipation results in reduced die temperature rise and hence equivalent increased charge current in thermal regulation. One way is to bypass some of the current through an external component, such as a resistor or diode. T A = 120°C − 0.5W ⋅ 150°C / W = 120°C − 75°C TA = 45°C The BL8573 can be used above 45°C ambient, but the charge current will be reduced from 400mA. The approximate current at a given ambient temperature can be approximated by: I BAT = Example: An BL8573 operating from a 5V wall adapter is programmed to supply 600mA full-scale current to a discharged Li-Ion battery with a voltage of 3.75V. θ 120°C − TA (VCC − VBAT ) ⋅ θ JA Assuming JA is 125°C /W, the approximate charge current at an ambient temperature of 25°C is: Using the previous example with an ambient temperature of 60°C, the charge current will be reduced to approximately: www.belling.com.cn 9 BL8573 I BAT = 120°C − 25°C = 608mA (5V − 3.75V ) ⋅ 125°C / W VCC BYPASS CAPACITOR Due to their self-resonant and high Q characteristics, some types of ceramic capacitors can cause high voltage transients under some start-up conditions (i.e connecting the charger input to a live power source). Adding a small value resistor in series with the ceramic capacitor can minimize start-up voltage transients By dropping voltage across a resistor in series with a 5V wall adapter (shown in Figure 3), the on-chip power dissipation can be decreased, thus increasing the thermally regulated charge current I BAT = 120 °C − 25 °C (V S − I BAT RCC − V BAT ) ⋅ θ JA CHARGE CURRENT SOFT-START To avoid the start-up transients, a soft-start circuit is included to ramp the charge current from zero to programmed value over a period of time. This has the effect of minimizing the transient current load on the power supply during start-up. BL857 BL8573 Figure 3. A Circuit to Maximize Thermal Mode Charge Current www.belling.com.cn 10 BL8573 PACKAGE LINE Package SOT-23-6 Devices per reel 3000Pcs Unit mm Devices per reel 2500 Unit mm Package specification： Package ESOP-8 Package specification： www.belling.com.cn 11