D1U5CS-H-2825-12-HA4C www.murata-ps.com AC/DC Front End Power Supply PRODUCT OVERVIEW The D1U5CS-H-2825 is a 2825 Watt, power-factor-corrected (PFC) front-end power supply for redundant systems. The main output is 12V and the standby output is 5V. Packaged in 1U low profile, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture system requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operating conditions. The D1U5CS-H-2825 is designed to autorecover from over-temperature faults. Status information is provided with front panel LEDs, logic signals and I2C management interface. ORDERING GUIDE Model Number Power Output Main Output Standby Output D1U5CS-H-2825-12-HA4C FEATURES n 2825W (220Vac) Output power 2825W Parameter Conditions n 1U sized; dimensions 5.1”x14.4”x1.61” n 23.9 Watts per cubic inch density Efficiency (230Vac) excludes fan load n 12V Main output, 5V standby output n N+1 redundancy capable, including hot plugging (up to 3 in parallel) n Active current sharing on main output, ORing FET n Overvoltage, Overcurrent, Overtemperature protection n Internal cooling fans (variable speed) 5V Airflow Connector Back to front, variable AC front INPUT CHARACTERISTICS Voltage Operating Range Frequency Maximum Current Inrush Current Power Factor n Certified to Climate Savers Computing InitiativeSM80 PLUS® Gold efficiency 12V Min. 180 47 Typ. 60 230Vac At 230Vac, full load 20% load 50% load 100% load Max. Units 264 63 16 90 Vac Hz Arms Apk 0.95 88.31 92.63 92.05 % OUTPUT VOLTAGE CHARACTERISTICS Output Voltage 12V n I²C Bus Interface with status indicators n RoHS compliant 5Vsb Parameter Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise1 Output Current Load Capacitance Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise1 Output Current Load Capacitance Conditions Min. Typ. Max. 12.12 11.75 12.48 120 233 2200 20MHz Bandwidth 0 0 5.0 4.85 20MHz Bandwidth 0 0 Units Vdc mV p-p A µF Vdc 5.15 50 4 200 mV p-p A µF Max. Units OUTPUT CHARACTERISTICS Parameter Conditions Min. AC ramp up PS_On activated 12V Ramp 1A/μs load capacitance is 2200μF 5Vsb Ramp 1A/μs load capacitance is 200μF Startup Time Transient Response Current sharing accuracy (up to 3 in parallel) At 100% load Holdup Time Remote Sense 20% load Typ. 1.5 150 s ms ±600 mV ±250 ±10 12 88.3 120 % ms mV 1 Ripple and noise are measured with 0.1 µF of ceramic capacitance and 10 µF of tantalum capacitance on each of the power supply outputs. A short coaxial cable with 50ohm scope termination is used. For full details go to www.murata-ps.com/rohs CB Test Certificate and Test Report www.murata-ps.com/support D1U5CS-H-2825-12-HA4C.A01 Page 1 of 5 D1U5CS-H-2825-12-HA4C AC/DC Front End Power Supply ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Storage Temperature Range Operating Temperature Range Operating Humidity Storage Humidity Shock Sinusoidal Vibration Non-condensing -40 0 10 5 Non-condensing 30G non operating 0.5G, 5 – 500 Hz Calculated per Telecordia SR322M1C2 Ta = 30°C Ta = 40°C ISO 7779-1999 MTBF Acoustic Typ. Max. 70 50 90 90 716,317 484,059 Units °C % hrs Safety Approvals: c-CSA-US (CSA 60950-1-03/UL 60950-1, Second Edition TUV EN 60950-1:2006+All EN6950-1:2006+A11 CB Report IEC 60950-1:2005(2nd ed.,) EN60950-1:2006+All Input Fuse Material Flammability Switching Frequency Weight Power Supply has internal 20A/250V fast blow fuse on the AC line input UL 94V-0 TBD 5.92lbs (2.691kg) PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Overtemperature Autorestart 55 Overvoltage Latching 13.3 12V Overcurrent Latching 243 Overvoltage Latching; requires AC recycling 5.6 5Vsb Overcurrent Autorecovering 5 Note: The main output is able to be re-enabled after OCP and OVP event by cycling PS_ON/L pin from low to high to low. Max. Units 65 14.4 255 6 7 °C V A V A Max. Units ISOLATION CHARACTERISTICS Parameter Conditions Insulation Safety Rating / Test Voltage Material Flammability Input to Output - Reinforced Input to Chassis - Basic UL 94V-0 Min. Typ. 3000 1500 Vrms Vrms CONTROL SIGNALS Status LED I2C Registers Conditions Description Off Yellow Flashing Green Green Status Output Fault 12V Output 12V Fan1 Monitor Fan2 Monitor Standby Output Standby Output Ambient temp HS1 temp HS2 temp VAC IAC No AC input to all PS Power Supply Failure Main Output Disabled Power Supply Good PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning & shutdown, AC Range 12V OV, 12V UV, 12V OC, Vsb Fail, Fan1 Warn, Fan2 Warn 10 bit scaled output voltage 10 bit scaled output current Fan speed (RPM) Fan speed (RPM) 10 bit scaled output voltage 10 bit scaled output current 10 bit ambient temperature reading 10 bit heatsink 1 temperature reading 10 bit heatsink 2 temperature reading 10 bit scaled input voltage 10 bit scaled input current www.murata-ps.com/support D1U5CS-H-2825-12-HA4C.A01 Page 2 of 5 D1U5CS-H-2825-12-HA4C AC/DC Front End Power Supply EMISSIONS AND IMMUNITY Characteristic Description Harmonics Voltage Fluctuation and Flicker Emission Conducted Emission Radiated IEC/EN 61000-3-2 IEC/EN 61000-3-3 FCC 47 CFR Parts 15/CISPR 22/EN55022 FCC 47 CFR Parts 15/CISPR 22/EN55022 Criteria ESD IEC/EN 61000-4-2 Electromagnetic Field Electrical Fast Transients/Burst Surge RF Conducted Immunity Magnetic Immunity Voltage dips, interruptions IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11 Class A, 4dB margin Class A 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge 1kV/2kV, Performance Criteria B 3 Vac, 80% AM, 1kHz, Performance Criteria A 3 A/m OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI PowerBlade # 51939-486LF P1 VOUT P2 VOUT P3 VOUT P4 VRTN P5 VRTN P6 VRTN P7 VRTN P8 VRTN P9 VRTN P10 VOUT P11 VOUT P12 x1 x2 x3 x4 x5 x6 AC_OK/H PW_OK/L VSB Return VSB Return VSB +OUT VSB +OUT D SPARE SMB/ Alert VSB Return VSB Return VSB +OUT VSB +OUT C I_SHARE I2C ADR0 I2C ADR1 I2C ADR2 PS_KILL PS_ Present B SENSE + SENSE - I2C DATA I2C CLOCK SPARE PS_ON/L A VOUT mate-last pins High Level Low Level I Max Pin Assignment Signal Name Description P1, P2, P3, P10, P11, P12 P4, P5, P6, P7, P8, P9 A1 A2 C5, C6, D5, D6 C3, C4, D3, D4 B1 VOUT VRTN Sense + Sense VSB VSB Return I_Share Main output voltage Main output voltage, return VOUT remote sense, positive node input, connected to the +ve load point VOUT remote sense, negative node input, connected to the -ve load point Standby voltage output Standby voltage, return, tied internally to Output Return Active load sharing bus 0 – 8V -4 mA / +5 mA D1 AC_OK/H Input AC Voltage “OK” signal output (open drain with internal pull up of 10kΩ to Vsb) >2.5V <0.8V -32mA D2 PW_OK/L Power OK signal output (open drain with internal pull up of 10kΩ to Vsb) >2.5V <0.8V -32mA C2 SMB/Alert SMB/Alert signal output (open collector) B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and first-break contact for hot plugging). This signal overrides PS-On in disabling the Main Output >2.1V (open) <0.8V (active, PS:On) N/A B6 PS_Present Internally tied to Vsb return 0V A6 PS_On/L Internal 5.11KΩ pull-up to Vsb, (accepts open collector/drain drive). This signal to be pulled low to turn-on main output of power supply >0.7 x Vsb <0.3 x Vsb A3 I2C Data I2C serial data bus; internal 4.64kΩ pull-up to 3.3V >0.7 x Vsb <0.3 x Vsb A4 I2C Clock I2C serial clock bus; internal 4.64kΩ pull-up to 3.3V >0.7 x Vsb <0.3 x Vsb B2 I2C Adr0 Address input 0, internal 10kΩ pull-up to Vsb >0.7 x Vsb <0.3 x Vsb B3 I2C Adr1 Address input 1, internal 10kΩ pull-up to Vsb >0.7 x Vsb <0.3 x Vsb B4 I2C Adr2 Address input 2, internal 10kΩ pull-up to Vsb >0.7 x Vsb <0.3 x Vsb www.murata-ps.com/support D1U5CS-H-2825-12-HA4C.A01 Page 3 of 5 D1U5CS-H-2825-12-HA4C AC/DC Front End Power Supply DC OUTPUT RIGHT ANGLE CONNECTOR IN POWER SUPPLY (viewed from end of power supply) dfdj DC OUTPUT VERTICAL CONNECTOR MATE ON BACKPLANE (backplane view) www.murata-ps.com/support D1U5CS-H-2825-12-HA4C.A01 Page 4 of 5 D1U5CS-H-2825-12-HA4C AC/DC Front End Power Supply MECHANICAL DIMENSIONS Airflow Back to Front AC Input Connector: The AC input connector is standard IEC320 C20 (20A). Dimensions: 5.1” x 14.4” x 1.61” [129.5mm x 367mm x 41mm] D1U5CS MATING CONNECTORS 12V D1U5CS mating connector Press Fit Straight Solder 1 Right Angle Straight Right Angle MPS TBD 4321-01576-0 TBD TBD FCI 51940-323 51915-132LF TBD TBD 1 Solder connector recommended for board thickness of <0.090 OPTIONAL ACCESSORIES Description Part Number 12V D1U5CS Connector Card D1U5CS-12-CONC APPLICATION NOTES Description Application Note 12V D1U5CS Connector Card ACAN-41 D1U5CS-H-2825-12-HxxC Communication Protocol ACAN-40 D1U EEPROM Specification ACAN-37 Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2012 Murata Power Solutions, Inc. www.murata-ps.com/support D1U5CS-H-2825-12-HA4C.A01 Page 5 of 5