Typical Performance Characteristics www.vishay.com Vishay Sprague Molded Chip Tantalum Capacitors, Automotive Grade ELECTRICAL PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Category temperature range -55 °C to +85 °C (to +125 °C / +150 °C / +175 °C with voltage derating - refer to graph “Category Voltage vs. Temperature”) (1) Capacitance tolerance ± 20 %, ± 10 %, tested via bridge method, at 25 °C, 120 Hz Dissipation factor Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz ESR Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz Leakage current After application of rated voltage applied to capacitors for 5 min using a steady source of power with 1 k resistor in series with the capacitor under test, leakage current at 25 °C is not more than 0.01 CV or 0.5 μA, whichever is greater. Note that the leakage current varies with temperature and applied voltage. See graph “Typical Leakage Current Temperature Factor” for the appropriate adjustment factor. Capacitance change by temperature +30 % max. (at +175 °C) +20 % max. (at +125 °C and +150 °C) +10 % max. (at +85 °C) -10 % max. (at -55 °C) Reverse voltage Capacitors are capable of withstanding peak voltages in the reverse direction equal to: 10 % of the DC rating at +25 °C 5 % of the DC rating at +85 °C 1 % of the DC rating at +125 °C Ripple current For maximum ripple current values (at 25 °C) refer to relevant datasheet. If capacitors are to be used at temperatures above +25 °C, the permissible RMS ripple current (or voltage) shall be calculated using the derating factors: 1.0 at +25 °C 0.9 at +85 °C 0.4 at +125 °C 0.3 at +150 °C 0.2 at +175 °C Maximum operating and surge voltages vs. temperature +85 °C +125 °C +150 °C / +175 °C RATED VOLTAGE (V) SURGE VOLTAGE (V) CATEGORY VOLTAGE (V) SURGE VOLTAGE (V) CATEGORY VOLTAGE (V) 4 5.2 2.7 3.4 n/a 6.3 8 4 5 3 10 13 7 8 5 16 20 10 12 8 20 26 13 16 10 25 32 17 20 12.5 35 46 23 28 17.5 50 65 33 40 25 50 (2) 60 33 40 n/a 63 75 42 50 n/a 75 (3) 75 50 50 n/a Notes • All information presented in this document reflects typical performance characteristics. (1) Series TH3 - up to 150 °C; TH4 - up to 175 °C. (2) Capacitance value 15 μF and higher. (3) For 293D and TR3 only. Revision: 11-May-15 Document Number: 40215 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Typical Performance Characteristics www.vishay.com Vishay Sprague CATEGORY VOLTAGE VS. TEMPERATURE Category Voltage (V) 1.0 0.8 0.6 0.4 0.2 Voltage-Temperature Derating Coefficient 0 -55 0 25 85 125 150 175 Temperature (°C) Note • Below 85 °C category voltage is equal to rated voltage. TYPICAL LEAKAGE CURRENT FACTOR 100 +175 °C +150 °C +125 °C 10 Leakage Current Factor +85 °C +55 °C 1 +25 °C 0 °C 0.1 - 55 °C 0.01 0.001 0 10 20 30 40 50 60 70 80 90 100 Percent of Rated Voltage Note • At +25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table. At +85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table. At +125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table. At +150 °C, the leakage current shall not exceed 15 times the value listed in the Standard Ratings table. At +175 °C, the leakage current shall not exceed 18 times the value listed in the Standard Ratings table. Revision: 11-May-15 Document Number: 40215 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Typical Performance Characteristics www.vishay.com Vishay Sprague ENVIRONMENTAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE High temperature exposure (storage) MIL-STD-202, method 108 1000 h, at maximum rated temperature, unpowered Capacitance change Dissipation factor Leakage current ESR Within ± 20 % of initial value Initial specified limit Initial specified limit Initial specified limit Operational life test at +125 °C AEC-Q200 1000 h application 2/3 of rated voltage Capacitance change Dissipation factor Leakage current ESR Within ± 20 % of initial value Initial specified limit Shall not exceed 10 times the initial limit Initial specified limit Operational life test at +150 °C (for TH3) and at +175 °C (for TH4) AEC-Q200 1000 h application 1/2 of rated voltage Capacitance change Dissipation factor Leakage current ESR Within ± 20 % of initial value Shall not exceed 3 times the initial limit Shall not exceed 10 times the initial limit Shall not exceed 3 times the initial limit Surge voltage MIL-PRF-55365: 1000 successive test cycles at 85 °C of surge voltage (as specified in the table above), in series with a 33 resistor at the rate of 30 s ON, 30 s OFF Capacitance change Dissipation factor Leakage current ESR Within ± 30 % of initial value Shall not exceed 1.5 times the initial limit Shall not exceed 2 times the initial limit Shall not exceed 1.5 times the initial limit Biased humidity test AEC-Q200 At 85 °C / 85 % RH, 1000 h, with rated voltage applied Capacitance change Dissipation factor Leakage current ESR Within ± 20 % of initial value Shall not exceed 3 times the initial limit Shall not exceed 10 times the initial limit Shall not exceed 3 times the initial limit Temperature cycling AEC-Q200 / JESD22, method JA-104 -55 °C / +125 °C, for 1000 cycles Capacitance change Dissipation factor Leakage current ESR Within ± 20 % of initial value Initial specified limit Initial specified limit Initial specified limit MECHANICAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Vibration MIL-STD-202, method 204: 10 Hz to 2000 Hz, 5 g peak for 20 min, 12 cycles each of 3 orientations (total 36 cycles), at rated voltage Capacitance change Dissipation factor Leakage current Within ± 20 % of initial value Initial specified limit Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Mechanical shock MIL-STD-202, method 213, condition F, 1500 g peak, 0.5 ms, half-sine Capacitance change Dissipation factor Leakage current Within ± 20 % of initial value Initial specified limit Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Resistance to solder heat MIL-STD-202, method 210, condition D Solder dip 260 °C ± 5 °C, 10 s Capacitance change Dissipation factor Leakage current Within ± 20 % of initial value Initial specified limit Initial specified limit Resistance to solvents MIL-STD-202, method 215 Capacitance change Dissipation factor Leakage current Within ± 20 % of initial value Initial specified limit Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Body marking shall remain legible. Solderability AEC-Q200 / J-STD-002 Electrical test not required Terminal strength / Shear force test AEC-Q200-006 Apply a pressure load of 17.7 N (1.8 kg) for 60 s horizontally to the center of capacitor side body Exception: for case size 0603 pressure load is 5N Part should not be sheared off the pads and no body cracking post-conditioning. Electrical test not required. Flammability Encapsulation materials meet UL 94 V-0 with an oxygen index of 32 % n/a Revision: 11-May-15 Document Number: 40215 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000