Typical Performance Characteristics

Typical Performance Characteristics
www.vishay.com
Vishay Sprague
Solid Tantalum Chip Capacitors MICROTAN®
High Reliability Leadframeless Molded Capacitors
TM8 and DLA 11020
ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category temperature range
-55 °C to +85 °C (to +125 °C with voltage derating)
Capacitance tolerance
± 20 %, ± 10 %, tested via bridge method, at 25 °C, 120 Hz
Dissipation factor
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz.
ESR
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz.
Leakage current
After application of rated voltage applied to capacitors for 5 min using a steady source of power with 1 k
resistor in series with the capacitor under test, leakage current at 25 °C is not more than described in
Standard Ratings table. Note that the leakage current varies with temperature and applied voltage. See
graph below for the appropriate adjustment factor.
Reverse voltage
Capacitors are capable of withstanding peak voltages in the reverse direction equal to:
10 % of the DC rating at +25 °C
5 % of the DC rating at +85 °C
1 % of the DC rating at +125 °C
Vishay does not recommend intentional or repetitive application of reverse voltage.
Ripple current and
Temperature derating
For maximum permissible ripple current (IRMS) or/and voltage (VRMS) please refer to product datasheet and
Guide to Application. If capacitors are to be used at temperatures above +25 °C, the permissible RMS
ripple current or voltage shall be calculated using the derating factors:
1.0 at +25 °C
0.9 at +85 °C
0.4 at +125 °C
TYPICAL LEAKAGE CURRENT FACTOR RANGE
100
Leakage Current Factor
+125 °C
10
+85 °C
+55 °C
+25 °C
1.0
0 °C
0.1
-55 °C
0.01
0.001
0
10
20
30
40
50
60
70
80
90
100
Percent of Rated Voltage
Notes
• At +25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table.
• At +85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table.
• At +125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table.
Revision: 16-Jan-14
Document Number: 40170
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
ENVIRONMENTAL AND MECHANICAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
In accordance with MIL-PRF-55365
In accordance with MIL-PRF-55365
(as for style CWR15)
Vibration
Thermal shock
Resistance to solder heat
Moisture resistance
Stability at low and high
temperatures
Surge voltage
Life test
Solderability
Resistance to solvents
Terminal strength/
Shear stress test
Method: AEC-Q200-006, conditions:
Pressure load of 5 N for 10 s ± 1 s
Flammability
Encapsulation materials meet UL 94 V-0 with an
oxygen index of 32 %.
There shall be no mechanical or visual damage and
the components shall meet the original electrical
requirements.
Note
• All measurements to be performed after 24 h conditioning at room temperature.
Revision: 16-Jan-14
Document Number: 40170
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000