T22 Datasheet

T22
www.vishay.com
Vishay
Wet Tantalum SMD Capacitors, Tantalum Metal Case with
Glass-to-Tantalum Hermetic Seal
FEATURES
• Enhanced performance, high reliability design
• SMD, standard tin / lead (Sn / Pb), 100 % tin
(RoHS-compliant) available
Available
Available
• Mounting: surface-mount
• Increased thermal shock capability of 300 cycles
• Designed for the avionics and aerospace
applications
PERFORMANCE CHARACTERISTICS
Operating Temperature: -55 °C to +85 °C
(to +125 °C with voltage derating)
Available
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
DC Leakage Current (DCL Max.): at +25 °C and above:
leakage current shall not exceed the values listed in the
Standard Ratings table.
Note
* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details.
Capacitance Range: 10 μF to 68 μF
Capacitance Tolerance: ± 10 %, ± 20 % standard
Voltage Rating: 50 VDC to 125 VDC
ORDERING INFORMATION
T22
C
686
K
050
E
S
S
TYPE
CASE
CODE
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE
RATING AT +85 °C
TERMINATION /
PACKAGING
RELIABILITY
GRADE
ESR
See
Ratings
and
Case
Codes
table
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
K = ± 10 %
M = ± 20 %
This is expressed
in volts. To
complete the
three-digit block,
zeros precede the
voltage rating.
A decimal point is
indicated by an
“R” (6R3 = 6.3 V).
E = Sn / Pb solder /
7" (178 mm) reel
L = Sn / Pb solder /
7" (178 mm), 1/2 reel
C = 100 % tin /
7" (178 mm), reel
H = 100 % tin /
7" (178 mm), 1/2 reel
R = Sn / Pb solder /
7" (178 mm), partial reel
U = 100 % tin /
7" (178 mm), partial reel
S = 48 h
burn-in
Z = nonestablished
reliability
S=
standard
DIMENSIONS in inches [millimeters]
H
L
TW
TW
P
W
P
CASE CODE
L
W
H
P
TW
C
0.354 max.
[9 max.]
0.279 ± 0.008
[7.1 ± 0.2]
0.291 ± 0.008
[7.4 ± 0.2]
0.098 ± 0.008
[2.5 ± 0.2]
0.197 ± 0.008
[5.0 ± 0.2]
Revision: 25-Apr-16
Document Number: 40187
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
MARKING
VOLTAGE CODE
V
CODE
50
T
75
S
100
R
125
B
Polarity mark
686T
YYXX
Capacitance
Year
Trademark
Voltage
Week
2
STANDARD RATINGS
CAPACITANCE
AT +25 °C
120 Hz
(μF)
CASE
CODE
MAX. ESR MAX. IMP.
AT +25 °C AT -55 °C
120 Hz
120 Hz
()
()
PART NUMBER
MAX. DCL
(μA) AT
+25 °C
+85 °C
AND
+125 °C
MAX. CAPACITANCE
CHANGE (%)
AC
RIPPLE
+85 °C
-55 °C +85 °C +125 °C 40 kHz
(mARMS)
50 VDC AT +85 °C; 30 VDC AT +125 °C
68
C
T22C686(1)050(2)(3)(4)
1.50
35
1
5
-25
8
15
1650
5
-25
5
9
1310
5
-18
3
10
1030
5
-15
3
10
832
75 VDC AT +85 °C; 50 VDC AT +125 °C
33
C
(1)
T22C336(1)075(2)(3)(4)
15
C (1)
T22C156(1)100(2)(3)(4)
2.50
66
1
100 VDC AT +85 °C; 65 VDC AT +125 °C
3.50
125
1
125 VDC AT +85 °C; 85 VDC AT +125 °C
10
C
T22C106(1)125(2)(3)(4)
5.50
175
1
Notes
• Part number definitions:
(1) Capacitance tolerance: K, M
(2) Termination and packaging: C, H, E, L, R, U
(3) Reliability level: Z, S
(4) ESR: S
(1) Rating in development, contact factory for availability
POWER DISSIPATION
CASE CODE
MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR
C
0.9
STANDARD PACKAGING QUANTITY
CASE CODE
C
Revision: 25-Apr-16
UNITS PER REEL
7" FULL REEL
7" HALF REEL
7" PARTIAL REEL
100
50
25
Document Number: 40187
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
TAPE AND REEL PACKAGING in inches [millimeters]
0.157 ± 0.004
[4.0 ± 0.10]
T2
(max.)
Deformation
between
embossments
0.024
[0.600]
max.
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Top
cover
tape
A0
K0
B1 (max.) (6)
0.030 [0.75]
min. (3)
B0
Top
cover
tape
For tape feeder
reference only
including draft.
Concentric around B0
10 pitches cumulative
tolerance on tape
± 0.008 [0.200]
Embossment
0.079 ± 0.002
0.069 ± 0.004
[2.0 ± 0.05]
[1.75 ± 0.10]
F
W
20°
Maximum
component
rotation
0.030 [0.75]
min. (4)
(Side or front sectional view)
Center lines
of cavity
0.004 [0.10]
max.
P1
USER DIRECTION
OF FEED
D1 (min.) for components
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
Maximum
cavity size (1)
Cathode (-)
R
min.
Anode (+)
Bending radius (2)
DIRECTION OF FEED
3.937 [100.0]
20° maximum
component rotation
Typical
component
cavity
center line
B0
A0
(Top view)
Typical
component
center line
R minimum:
16 mm = 1.181" (30 mm)
0.039 [1.0]
max.
Tape
0.039 [1.0]
max.
0.9843 [250.0]
Camber
(Top view)
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
Notes
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body
0
0
0
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
(3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
(4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
(5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
(6) B dimension is a reference dimension tape feeder clearance only.
1
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
16 mm
Revision: 25-Apr-16
W
P2
F
E1
E2 MIN.
0.630 + 0.012 / - 0.004
[16.0 + 0.3 / - 0.1]
0.079 ± 0.004
[2.0 ± 0.1]
0.295 ± 0.004
[7.5 ± 0.1]
0.069 ± 0.004
[1.75 ± 0.1]
0.561
[14.25]
Document Number: 40187
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
CARRIER TAPE DIMENSIONS in inches [millimeters]
TYPE
CASE CODE
TAPE WIDTH W
(mm)
P1
K0 MAX.
B1 MAX.
C
16
0.476 ± 0.004
[12.0 ± 0.1]
0.31
[7.9]
0.45
[11.3]
T22
RECOMMENDED REFLOW PROFILES
Capacitors should withstand reflow profile as per J-STD-020 standard
TEMPERATURE (°C)
TP
TL
Ts max.
TC - 5 °C
tp
Max. ramp-up rate = 3 °C/s
Max. ramp-down rate = 6 °C/s
tL
Preheat area
Ts min.
ts
25
Time 25 °C to peak
TIME (s)
PROFILE FEATURE
SnPb EUTECTIC ASSEMBLY
LEAD (Pb)-FREE ASSEMBLY
Temperature min. (Ts min.)
100 °C
150 °C
Temperature max. (Ts max.)
150 °C
200 °C
60 s to 120 s
60 s to 120 s
3 °C/s max.
3 °C/s max.
Preheat / soak
Time (ts) from (Ts min. to Ts max.)
Ramp-up
Ramp-up rate (TL to TP)
Liquidus temperature (TL)
183 °C
217 °C
60 s to 150 s
60 s to 150 s
Peak package body temperature (Tp)
220
245
Time (tp) within 5 °C of the specified
classification temperature (TC)
20 s
30 s
6 min max.
8 min max.
Ramp-down rate (TP to TL)
6 °C/s max.
6 °C/s max.
Time 25 °C to peak temperature
6 min max.
8 min max.
Time (tL) maintained above TL
Time 25 °C to peak temperature
Ramp-down
PAD DIMENSIONS in inches [millimeters]
B
D
C
A
CASE CODE
A (MIN.)
B (NOM.)
C (NOM.)
D (NOM.)
C
0.295 [7.50]
0.138 [3.50]
0.100 [2.50]
0.374 [9.50]
Revision: 25-Apr-16
Document Number: 40187
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
TYPICAL PERFORMANCE CHARACTERISTICS OF T22 CAPACITORS
ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category temperature range
-55 °C to +85 °C (to +125 °C with voltage derating)
Capacitance tolerance
± 20 %, ± 10 % at +25 °C, 120 Hz
Capacitance change by temperature
Limit per Standard Ratings table
ESR
Limit per Standard Ratings table, at +25 °C, 120 Hz
Impedance
Limit per Standard Ratings table, at -55 °C, 120 Hz
DCL (leakage current)
Limit per Standard Ratings table
AC ripple current
Limit per Standard Ratings table, at +85 °C and 40 kHz
Reverse voltage
Reverse voltage shall be in accordance with MIL-PRF-39006, paragraphs 3.23 and 4.8.19, except DC
potential will be maximum of 3 V
Maximum operating voltage
OPERATING TEMPERATURE
+85 °C
Surge voltage
+125 °C
RATED VOLTAGE
(VDC)
SURGE VOLTAGE
(VDC)
DERATED VOLTAGE
(VDC)
50
57.5
30
75
86.2
50
100
115.0
65
125
144.0
85
The DC surge voltage is the maximum voltage to which the capacitor can be subjected under any
conditions including transients and peak ripple at the highest line voltage.
The DC surge voltage is 115 % of rated DC voltage
PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Surge voltage
In accordance with MIL-PRF-39006:
85 °C 1000 successive test cycles at
the applicable DC surge voltage
specified in series with a 1 k resistor
at the rate of 30 s ON, 5.5 min OFF
Capacitance change
Leakage current
Within ± 10 % of initial measured value
Not to exceed specified value
Life testing
In accordance with MIL-PRF-39006:
capacitors shall be capable of
withstanding a 2000 h life test at a
temperature +85 °C at rated voltage,
or a 2000 h life test at a temperature
+125 °C at derated voltage
Capacitance change
Leakage current at 85 °C / 125 °C
Leakage current at 25 °C
ESR
+10 % / -20 % of initial measured value
Not to exceed 125 % of initial specified value
Not to exceed specified value
Not to exceed 200 % of specified value
AC ripple life
In accordance with MIL-PRF-39006: 2000 h, +85 °C
Revision: 25-Apr-16
Document Number: 40187
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
ENVIRONMENTAL CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Stability at low and
high temperatures
As specified in MIL-PRF-39006
The capacitors shall meet the requirements of MIL-PRF-39006
Seal
MIL-PRF-39006
Method 112 of MIL-STD-202,
conditions A and C
When the capacitors are tested as specified in MIL-PRF-39006,
there shall be no evidence of leakage.
Moisture resistance
MIL-PRF-55365
Method 106 of MIL-STD-202,
number of cycles: 10 continuous cycles except
that steps 7a and 7b shall be omitted.
DC leakage
Capacitance change
ESR
Barometric pressure
(reduced)
Method 105 of MIL-STD-202, condition E
(150 000 feet) (45,720.1 m).
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Low temperature
storage
MIL-PRF-39006
Method 502 of MIL-STD-810,
Storage temperature: - 62 °C + 0 °C, - 3 °C
Exposure time: 72 h followed by a 1 h exposure
at + 125 °C + 7 °C, - 0 °C within 24 h after low
temperature storage.
DC leakage
Capacitance change
ESR
Salt atmosphere
(corrosion)
MIL-PRF-39006
Method 101 of MIL-STD-202,
condition B (48 h), applicable salt solution: 5 %
There shall be no harmful corrosion. Marking shall remain legible.
Not exceed 125 % of the specified value
Within ±10 % of the initial measured value
Not exceed the specified value
Not to exceed 125 % of the specified value
Within ± 10 % of the initial measured value
Not exceed the specified value
MECHANICAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Shear test
AEC-Q200-006
Apply a pressure load of 5 N for 10 s ± 1 s
horizontally to the center of capacitor
side body.
DC leakage
Capacitance change
ESR
Not to exceed 125 % of the specified value
Within ± 10 % of the initial measured value
Not exceed the specified value
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Solderability
MIL-STD-202, method 208, test B
ANSI/J-STD-002:
SnPb solder - test B
Pb-free solder - test B1
All terminations shall exhibit a continuous solder coating free
from defects for a minimum of 95 % of the critical area of any
individual lead.
Resistance
to solvent
MIL-STD-202, method 215
There shall be no mechanical or visual damage to capacitors
post-conditioning. Marking shall remain legible, no degradation
of the can material.
Insulation
resistance
Method 302 of MIL-STD-202, condition B
(500 VDC ± 10 %)
The insulation resistance shall be not less than 100 M.
The capacitors shall meet the requirements of MIL-PRF-39006.
Shock
(specified pulse)
MIL-STD-202, method 213,condition I (100 g)
The capacitors shall meet the requirements of MIL-PRF-39006.
Vibration,
high frequency
MIL-STD-202, method 204, condition E
(50 g peak)
The capacitors shall meet the requirements of MIL-PRF-39006.
Random vibration
MIL-STD-202, method 214, condition II-G
(overall RMS 27.78 G)
The capacitors shall meet the requirements of MIL-PRF-39006.
Thermal shock
MIL-STD-202, method 107, condition A
Thermal shock shall be in accordance with MIL-PRF-39006 when
tested for 300 cycles.
Resistance to
soldering heat
MIL-STD-202, method 210, condition J,
except with only one heat cycle
Capacitance change
ESR
Leakage current
Within ± 10 % of initial
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Revision: 25-Apr-16
Document Number: 40187
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
Vishay
TYPICAL CURVES OF IMPEDANCE AS A FUNCTION OF FREQUENCY AT VARIOUS TEMPERATURES
“C” Case 50 V Capacitors
Impedance (Ω)
100
10
-55 °C
-40 °C
-20 °C
1.0
+85 °C
+125 °C
0.1
100
1K
100K
10K
Frequency (Hz)
+25 °C
1M
10M
PERFORMANCE CHARACTERISTICS
1.
Operating Temperature: capacitors are designed to
operate over a temperature range of -55 °C to +125 °C.
UP TO +85 °C
(V)
50
75
100
125
2.
3.
3.1
3.2
3.3
4.
4.1
5.
AT +125 °C
(V)
30
50
65
85
DC Working Voltage: the DC working voltage is the
maximum operating voltage for continuous duty at the
rated temperature.
Surge Voltage: the surge voltage rating is the maximum
voltage to which the capacitors should be subjected
under any conditions. This includes transients and peak
ripple at the highest line voltage.
The surge voltage of capacitors is 115 % of rated DC
working voltage.
Surge Voltage Test: capacitors shall withstand the
surge voltage applied through a 1000  ± 10 % resistor
in series with the capacitor and voltage source at the
rate of one-half minute on, five and one-half minutes off,
for 1000 successive test cycles at +85 °C.
Following the surge voltage test, the capacitance at
+25 °C shall not have changed by more than ± 10 % and
the equivalent series resistance and DC leakage current
will not exceed the values shown in the Standard
Ratings table for each capacitor.
Capacitance Tolerance: the capacitance of all
capacitors shall be within the specified tolerance limits
of the nominal rating.
Measurements shall be made by the bridge method at
or referred to a frequency of 120 Hz at a temperature of
+25 °C. The maximum voltage applied to the capacitors
during measurement shall be 1 VRMS. Measurement
accuracy of the bridge shall be within ± 2 %.
Capacitance Change With Temperature: the
capacitance change with temperature shall not exceed
the values given in the Standard Ratings table for each
capacitor.
Revision: 25-Apr-16
6.
Equivalent Series Resistance: measurements shall be
made by the bridge method at, or referred to, a
frequency of 120 Hz at a temperature of +25 °C. A
maximum of 1 VRMS shall be applied during
measurement.
6.1 The equivalent series resistance shall not exceed the
maximum value in ohms listed in the Standard Ratings
table for each capacitor.
6.2 The dissipation factor may be calculated from the
equivalent series resistance and capacitance values as
shown:
2fRC
DF = ----------------4
10
where:
DF = dissipation factor in %
R = ESR in 
C = capacitance in μF
f = frequency in Hz
At 120 Hz, the above equation becomes:
RxC
DF = --------------13.26

For example, percent dissipation factor of a 30 μF, 6 V
capacitor, which has a maximum ESR of 4.0  at
+25 °C and 120 Hz, would be calculated as shown:
2 x 120 x 4 x 30
4 x 30
- = ---------------- = 9.05 %
DF = --------------------------------------------4
13.26
10
7.
Leakage Current: measurements shall be made at the
applicable rated working voltage at +25 °C ± 5 °C
through application of a steady source of power, such
as a regulated power supply. A 1000  resistor to limit
the charging current shall be connected in series with
each capacitor under test. Rated working voltage shall
be applied to capacitors for 5 minutes before making
leakage current measurements.
Document Number: 40187
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
7.1 The maximum leakage current for any capacitor shall
not exceed the maximum value in μA listed in the
Standard Ratings table for each capacitor.
Note
• Leakage current varies with applied voltage. See graph next
column for the appropriate adjustment factor
8.
Low Temperature Impedance: the impedance of any
capacitor at -55 °C at 120 Hz, shall not exceed the
values given in the Standard Ratings table.
9.
Life Test: capacitors are capable of withstanding a
2000 h life test at a temperature of +85 °C or +125 °C at
the applicable rated DC working voltage.
9.1 Following the life test, the capacitors shall be returned
to 25 °C ± 5 °C. The leakage current, measured at
the +85 °C rated voltage, shall not be in excess of
the original requirement; the capacitance value shall
not exceed 150 % of the initial requirement; the
capacitance value shall not change more than + 10 % /
- 20 % from the initial measurement.
TYPICAL LEAKAGE CURRENT FACTOR
RANGE
1.0
0.9
0.8
0.7
0.6
10.
Ripple Life Test at +85 °C: capacitors shall be tested
in
accordance
with
military
specification
MIL-PRF-39006 except that:
a) Operation conditions: this test shall be run at a
frequency of 40 kHz ± 2 kHz sinusoidal and at the
RMS ripple current levels specified in the Standard
Ratings table.
b) Applied DC voltage shall be reduced so that the
peak AC voltage plus DC voltage shall not exceed
the rated voltage of the capacitor in either the
forward or reverse direction.
10.1 When tested as specified above, capacitors shall meet
the following requirements:
a) The DC leakage current at +25 °C and at +85 °C
shall not exceed the original requirements.
b) The capacitance shall not change more than ± 15 %
from the initial measured value.
c) The dissipation factor shall not exceed the original
requirements.
d) Visual examination: There shall be no damage,
obliteration of marking or leakage of electrolyte.
GUIDE TO APPLICATION
1. AC Ripple Current: subjecting a capacitor to an AC
voltage causes an AC current to flow through it. The
amplitude of the current is dependent on the impedance
of the capacitor at the frequency of the applied signal:
V
I = --Z
0.5
where:
I = ripple current
V = applied AC voltage
Z = impedance of capacitor (frequency dependent)
This current causes heating in the capacitor because of
I2R losses (R is the equivalent series resistance at the
applied frequency). This heating or power dissipation, is
one of the limiting factors of the capacitor’s ripple current
rating.
These power dissipation ratings are based on a
calculated +50 °C internal temperature rise in still air. The
maximum allowable ripple currents given in the Standard
Ratings table are based on these ratings and the
maximum equivalent series resistance at that frequency.
The relationship is written as follows:
0.4
0.3
LEAKAGE CURRENT FACTOR
Vishay
0.2
0.1
0.09
0.08
0.07
0.06
0.05
2
P = I R
0.04
where:
P = maximum power
I = maximum ripple current
R = equivalent series resistance
Therefore:
0.03
0.02
I =
0.01
0
10
20 30 40 50 60 70 80 90 100
PERCENT OF RATED VOLTAGE
Revision: 25-Apr-16
P
---R
where:
R is in 
P is in W
I is in ARMS
Document Number: 40187
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
T22
www.vishay.com
AC Ripple Voltage: in operation, the peak voltage
across the capacitor (DC working voltage plus peak
ripple voltage) must not exceed the rated working
voltage of the capacitor. The DC component of the
applied voltage should be sufficiently large to prevent
polarity reversal in excess of 3 V at +85 °C or 2 V at
125 °C.
TYP. ESR AS A FUNCTION OF FREQUENCY
EQUIVALENT SERIES RESISTANCE RATIO
2.
Vishay
There will be a point at the lower frequency and
capacitance values when the peak AC voltage will be
the limiting factor on the ripple current - not its heating
effects.
3.
Ripple Current Multipliers: the Standard Ratings table
list the maximum permissible RMS ripple current at
40 kHz for each rating. These values are based on the
maximum power dissipation allowed at that frequency.
This ripple current, will cause heating, which adds to the
ambient
temperature.
The
higher
ambient
temperatures, voltage derating or current derating is
required (see “Ripple Current Multipliers” table). Also
shown are the multipliers for ripple currents at various
frequencies, caused by the frequency dependence of
the (ESR) equivalent series resistance. (see “Typical
ESR as a Function of Frequency” chart)
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
10
100
1K
10K
FREQUENCY (Hz)
1M
40K 100K





RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE AND APPLIES PEAK VOLTAGE
FREQUENCY
OF APPLIED
RIPPLE
CURRENT
120 Hz
800 Hz
1 kHz
10 kHz
40 kHz
100 kHz
AMBIENT STILL
 55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125
AIR TEMP. IN °C
% of
85 °C
rated
peak
voltage
100 %
0.60 0.39
-
-
0.71 0.43
-
-
0.72 0.46
-
-
0.88 0.55
-
-
1.0 0.63
-
-
1.1 0.69
-
-
90 %
0.60 0.46
-
-
0.71 0.55
-
-
0.72 0.55
-
-
0.88 0.67
-
-
1.0 0.77
-
-
1.1 0.85
-
-
80 %
0.60 0.52 0.35
-
0.71 0.62 0.42
-
0.72 0.62 0.42
-
0.88 0.76 0.52
-
1.0 0.87 0.59
-
1.1 0.96 0.65
-
70 %
0.60 0.58 0.44
-
0.71 0.69 0.52
-
0.72 0.70 0.52
-
0.88 0.85 0.64
-
1.0 0.97 0.73
-
1.1 1.07 0.80
-
66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50
Revision: 25-Apr-16
Document Number: 40187
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000