Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series TPSMA6L Series RoHS Pb e3 Description Uni-directional The TPSMA6L series is designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events, and it’s especially suitable for high reliability and automotive application. SMA low profile package (DO221-AC) has the same electronical performance as the SMB package but with low height profiles (1.1mm). Maximum Ratings and Thermal Characteristics Features (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 600 W Power Dissipation on Infinite Heat Sink at TA=50OC PM(AV) 3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only VF 3.5V V TJ , TSTG -55 to 150 °C RuJL 35 °C/W Operating Junction and Storage Temperature Range Typical Thermal Resistance Junction to Lead Typical Thermal Resistance Junction to Ambient RuJA 200 • Hi reliability application and automotive grade AEC Q101 qualified • SMA low profile package: less than 1.1 mm • Same power as standard SMB devices (600 W) • Footprint compatibility with standard SMA and SMB products (easy to layout) • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) °C/W Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TA=25ºC per Fig. 3. 2.Mounted on 5.0x5.0mm copper pad to each terminal. 3.Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only. Functional Diagram • Low inductance, excellent clamping capability • Fast response time: typically less than 1.0ns from 0 Volts to VBR min • Built-in strain relief • Glass passivated junction • Typical IR less than 1µA above 12V • High temperature soldering guaranteed: 260°C/10 seconds at terminals • VBR @TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient) • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Bi-directional Cathode Applications Anode TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Uni-directional TPSMA6L Series 123 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series Electrical Characteristics Part Number (Uni) Marking Reverse Stand off Voltage VR (Volts) TPSMA6L5.0A TPSMA6L6.0A TPSMA6L6.5A TPSMA6L7.0A TPSMA6L7.5A TPSMA6L8.0A TPSMA6L8.5A TPSMA6L9.0A TPSMA6L10A TPSMA6L11A TPSMA6L12A TPSMA6L13A TPSMA6L14A TPSMA6L15A TPSMA6L16A TPSMA6L17A TPSMA6L18A TPSMA6L20A TPSMA6L22A TPSMA6L24A TPSMA6L26A TPSMA6L28A TPSMA6L30A TPSMA6L33A TPSMA6L36A TPSMA6L40A TPSMA6L43A TPSMA6L45A TPSMA6L48A TPSMA6L51A TPSMA6L54A TPSMA6L58A TPSMA6L60A TPSMA6L64A TPSMA6L70A TPSMA6L75A TPSMA6L78A TPSMA6L85A AEA AGA AKA AMA APA ARA ATA AVA AXA AZA BEA BGA BKA BMA BPA BRA BTA BVA BXA BZA CEA CGA CKA CMA CPA CRA CTA CVA CXA CZA REA RGA RKA RMA RPA RRA RTA RVA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 TPSMA6L Series Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 124 Maximum Clamping Voltage VC @ Ipp (V) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 Maximum Maximum Peak Reverse Leakage Pulse Current IR @ VR Ipp (A) (µA) 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series I-V Curve Characteristics Uni-directional Vc VBR VR V IR VF IT Ipp PPPM VR VBR VC IR VF Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 2 - Peak Pulse Power Rating Curve Figure 1 - TVS Transients Clamping Waveform 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. TPSMA6L Series 125 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 tr=10µsec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 0 175 PM(AV), Steady State Power Dissipation (W) Cj (pF) Uni-directional V=0V Uni-directional @VR 100 10 Tj=25ºC f=1.0MHz Vsig=50mVp-p 10.0 100.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve 10000 1.0 2.0 t-Time (ms) Figure 5 - Typical Junction Capacitance 1 1.0 0 TA-Ambient temperature (ºC) 1000 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 1000.0 VBR - Reverse Breakdown Voltage (V) 3.6 RuJA=RuJL 3.0 2.4 1.8 1.2 RuJA=200°C/W 0.6 0 0 25 50 75 100 125 150 TA - Ambient Temperature (ºC) 175 bargaining TPSMA6L Series 126 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series Soldering Parameters Pre Heat Lead–free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 280°C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.002 ounce, 0.061 gram Temperature Cycling JESD22-A104 Case JEDEC DO-221AC Molded Plastic over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes cathode except Bipolar H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-B106 Dimensions Cathode Band Dimensions C A B G E F E D 3.12 (0.123) Inches Min Millimeters Max Min Max A 0.156 0.181 3.950 4.600 B 0.189 0.220 4.800 5.600 C 0.049 0.069 1.250 1.750 D 0.088 0.116 2.250 2.950 E 0.030 0.059 0.750 1.500 F 0.005 0.010 0.125 0.250 G 0.035 0.043 0.900 1.100 1 .20 (0.047) 1.52 (0.060) Mounting Pad Layout TPSMA6L Series 127 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Transient Voltage Suppression Diodes Surface Mount – 600W > TPSMA6L series Part Numbering System TPSMA6L xx Part Marking System A Cathode Band F (for Uni-directional products only) 5% VBR VOLTAGE TOLERANCE XXX VR VOLTAGE YMXXX SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Component Package Part number TPSMA6LxxA DO-221AC Packaging Option Quantity 3000 Tape & Reel – 12mm tape/7” reel Packaging Specification EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 7.0 (178) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) TPSMA6L Series Dimensions are in inches (and millimeters). Direction of Feed 128 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14