Datasheet

Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
SMAJ Series
RoHS
Pb e3
Description
Uni-directional
The SMAJ series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Bi-directional
Features
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E230531
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Symbol
Value
Unit
Peak Pulse Power Dissipation at
TA=25ºC by 10/1000µs Waveform
(Fig.2)(Note 1), (Note 2), (Note 5)
Parameter
PPPM
400
W
Power Dissipation on Infinite Heat
Sink at TL=50OC
PD
3.3
W
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave (Note 3)
IFSM
60
A
VF
3.5/5.0
V
Maximum Instantaneous Forward
Voltage at 25A for Unidirectional
Only (Note 4)
Operating Temperature Range
TJ
-65 to 150
°C
Storage Temperature Range
TSTG
-65 to 175
°C
Typical Thermal Resistance Junction
to Lead
RθJL
30
°C/W
Typical Thermal Resistance Junction
to Ambient
RθJA
120
°C/W
• 400W Peak pulse power
capability at 10/1000µs
waveform, repetition rate
(duty cycle): 0.01%
• Excellent clamping
capability
• Typical IR less than 1μA
when VBR min>12V
• For surface mounted
applications to optimize
board space
• Low profile package
• Typical failure mode is
short from over-specified
voltage or current
• Whisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
• IEC-61000-4-2 ESD
30kV(Air), 30kV (Contact)
• ESD protection of data
lines in accordance with
IEC 61000-4-2
• EFT protection of data
lines in accordance with
IEC 61000-4-4
• Built-in strain relief
• Fast response time:
typically less than 1.0ps
from 0 Volts to VBR min
• Glass passivated junction
• Low inductance
• High temperature
to reflow soldering
guaranteed: 260°C/40sec
• VBR @ TJ= VBR@25°C
x (1+αT x (TJ - 25))
(αT:Temperature
Coefficient, typical value
is 0.1%)
• Plastic package is
flammability rated
V-0 per Underwriters
Laboratories
• Meet MSL level1, per
J-STD-020, LF maximun
peak of 260°C
• Matte tin lead–free Plated
• Halogen free and RoHS
compliant
• Pb-free E3 means 2nd
level interconnect is
Pb-free and the terminal
finish material is tin(Sn)
(IPC/JEDEC J-STD609A.01)
Notes:
1. Non-repetitive current pulse, per Fig.4 and derated above TJ (initial) =25ºC per Fig. 3.
Applications
2.Mounted on 5.0x5.0mm copper pad to each terminal.
TVS devices are ideal for the protection of I/O Interfaces,
VCC bus and other vulnerable circuits used in Telecom,
Computer, Industrial and Consumer electronic
applications.
3.Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
device only.
4.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts.
5. The PPPM of stacked-die parts is 600W and please contact littelfuse for the detail
stacked-die parts.
Functional Diagram
Additional Infomarion
Bi-directional
Cathode
Datasheet
Resources
Samples
Anode
Uni-directional
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
Electrical Characteristics (T =25°C unless otherwise noted)
A
Part
Number
(Uni)
Part
Number
(Bi)
SMAJ5.0A
SMAJ6.0A
SMAJ6.5A
SMAJ7.0A
SMAJ7.5A
SMAJ8.0A
SMAJ8.5A
SMAJ9.0A
SMAJ10A
SMAJ11A
SMAJ12A
SMAJ13A
SMAJ14A
SMAJ15A
SMAJ16A
SMAJ17A
SMAJ18A
SMAJ20A
SMAJ22A
SMAJ24A
SMAJ26A
SMAJ28A
SMAJ30A
SMAJ33A
SMAJ36A
SMAJ40A
SMAJ43A
SMAJ45A
SMAJ48A
SMAJ51A
SMAJ54A
SMAJ58A
SMAJ60A
SMAJ64A
SMAJ70A
SMAJ75A
SMAJ78A
SMAJ85A
SMAJ90A
SMAJ100A
SMAJ110A
SMAJ120A
SMAJ130A
SMAJ150A
SMAJ160A
SMAJ170A
SMAJ180A
SMAJ200A
SMAJ220A
SMAJ250A
SMAJ300A
SMAJ350A
SMAJ400A
SMAJ440A
SMAJ5.0CA
SMAJ6.0CA
SMAJ6.5CA
SMAJ7.0CA
SMAJ7.5CA
SMAJ8.0CA
SMAJ8.5CA
SMAJ9.0CA
SMAJ10CA
SMAJ11CA
SMAJ12CA
SMAJ13CA
SMAJ14CA
SMAJ15CA
SMAJ16CA
SMAJ17CA
SMAJ18CA
SMAJ20CA
SMAJ22CA
SMAJ24CA
SMAJ26CA
SMAJ28CA
SMAJ30CA
SMAJ33CA
SMAJ36CA
SMAJ40CA
SMAJ43CA
SMAJ45CA
SMAJ48CA
SMAJ51CA
SMAJ54CA
SMAJ58CA
SMAJ60CA
SMAJ64CA
SMAJ70CA
SMAJ75CA
SMAJ78CA
SMAJ85CA
SMAJ90CA
SMAJ100CA
SMAJ110CA
SMAJ120CA
SMAJ130CA
SMAJ150CA
SMAJ160CA
SMAJ170CA
SMAJ180CA
SMAJ200CA
SMAJ220CA
SMAJ250CA
SMAJ300CA
SMAJ350CA
SMAJ400CA
SMAJ440CA
Marking
UNI
BI
AE
AG
AK
AM
AP
AR
AT
AV
AX
AZ
BE
BG
BK
BM
BP
BR
BT
BV
BX
BZ
CE
CG
CK
CM
CP
CR
CT
CV
CX
CZ
RE
RG
RK
RM
RP
RR
RT
RV
RX
RZ
SE
SG
SK
SM
SP
SR
ST
SV
SX
SZ
TE
TG
TK
TM
WE
WG
WK
WM
WP
WR
WT
WV
WX
WZ
XE
XG
XK
XM
XP
XR
XT
XV
XX
XZ
YE
YG
YK
YM
YP
YR
YT
YV
YX
YZ
ZE
ZG
ZK
ZM
ZP
ZR
ZT
ZV
ZX
ZZ
VE
VG
VK
VM
VP
VR
VT
VV
VX
VZ
UE
UG
UK
UM
Reverse
Stand off
Voltage VR
(Volts)
5.0
6.0
6.5
7.0
7.5
8.0
8.5
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
33.0
36.0
40.0
43.0
45.0
48.0
51.0
54.0
58.0
60.0
64.0
70.0
75.0
78.0
85.0
90.0
100.0
110.0
120.0
130.0
150.0
160.0
170.0
180.0
200.0
220.0
250.0
300.0
350.0
400.0
440.0
For bidirectional type having VR of 10 volts and less, the IR limit is double.
For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
MIN
MAX
Test
Current
IT
(mA)
6.40
6.67
7.22
7.78
8.33
8.89
9.44
10.00
11.10
12.20
13.30
14.40
15.60
16.70
17.80
18.90
20.00
22.20
24.40
26.70
28.90
31.10
33.30
36.70
40.00
44.40
47.80
50.00
53.30
56.70
60.00
64.40
66.70
71.10
77.80
83.30
86.70
94.40
100.00
111.00
122.00
133.00
144.00
167.00
178.00
189.00
201.00
224.00
246.00
279.00
335.00
391.00
447.00
492.00
7.00
7.37
7.98
8.60
9.21
9.83
10.40
11.10
12.30
13.50
14.70
15.90
17.20
18.50
19.70
20.90
22.10
24.50
26.90
29.50
31.90
34.40
36.80
40.60
44.20
49.10
52.80
55.30
58.90
62.70
66.30
71.20
73.70
78.60
86.00
92.10
95.80
104.00
111.00
123.00
135.00
147.00
159.00
185.00
197.00
209.00
222.00
247.00
272.00
309.00
371.00
432.00
494.00
543.00
10
10
10
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Breakdown
Voltage VBR
(Volts) @ IT
Maximum
Maximum
Maximum
Agency
Reverse
Clamping
Peak Pulse
Approval
Leakage IR
Voltage VC
Current Ipp
@ Ipp
@ VR
(A)
(V)
(µA)
9.2
10.3
11.2
12.0
12.9
13.6
14.4
15.4
17.0
18.2
19.9
21.5
23.2
24.4
26.0
27.6
29.2
32.4
35.5
38.9
42.1
45.4
48.4
53.3
58.1
64.5
69.4
72.7
77.4
82.4
87.1
93.6
96.8
103.0
113.0
121.0
126.0
137.0
146.0
162.0
177.0
193.0
209.0
243.0
259.0
275.0
292.0
324.0
356.0
405.0
486.0
567.0
648.0
713.0
43.5
38.8
35.7
33.3
31.0
29.4
27.8
26.0
23.5
22.0
20.1
18.6
17.2
16.4
15.4
14.5
13.7
12.3
11.3
10.3
9.5
8.8
8.3
7.5
6.9
6.2
5.8
5.5
5.2
4.9
4.6
4.3
4.1
3.9
3.5
3.3
3.2
2.9
2.7
2.5
2.3
2.1
1.9
1.6
1.5
1.5
1.4
1.2
1.1
1.0
0.8
0.7
0.6
0.6
800
800
500
200
100
50
20
10
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
I-V Curve Characteristics
Bi-directional
Uni-directional
Ipp
Vc VBR VR
V
IR VF
IT
IT
IR
Vc VBR VR
IR
IT
V
Ipp
Ipp
PPPM
VR
VBR
VC
IR
VF
VR VBR Vc
Peak Pulse Power Dissipation -- Max power dissipation
Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)
Reverse Leakage Current -- Current measured at VR
Forward Voltage Drop for Uni-directional
Ratings and Characteristic Curves (T =25°C unless otherwise noted)
A
Figure 1 - TVS Transients Clamping Waveform
Figure 2 - Peak Pulse Power Rating Curve
Voltage Transients
PPPM-Peak Pulse Power (kW)
100
Voltage or Current
Voltage Across TVS
Current Through TVS
Time
TJ initial = Tamb
10
stacked-die, 600W
at 10x1000µs, 25°C
1
0.1
0.001
Single die,400W
at 10x1000µs, 25°C
0.01
0.1
1
10
td-Pulse Width (ms)
continues on next page.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued)
A
Figure 3 - Peak Pulse Power Derating Curve
Figure 4 - Pulse Waveform
150
IPPM- Peak Pulse Current, % IRSM
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage %
100
80
60
40
20
0
0
25
50
75
100 125 150
TJ - Initial Junction Temperature (ºC)
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
Peak Value
IPPM
100
Half Value
IPPM IPPM
( )
2
50
0
175
10/1000µsec. Waveform
as defined by R.E.A
td
1.0
0
2.0
3.0
4.0
t-Time (ms)
Figure 5 - Typical Junction Capacitance
Figure 6 - Typical Transient Thermal Impedance
1000
Transient Thermal Impedance ( °C/W)
10000
Uni-direconal V=0V
1000
Cj (pF)
tr=10µsec
Bi-direconal V=0V
100
Uni/Bi-direconal
V=VR
10
100
10
1
0.1
0.001
1
1
10
100
1000
0.01
0.1
VBR - Reverse Breakdown Voltage (V)
Figure 7 - Maximum Non-Repetitive Forward Surge
Current Uni-Directional Only
10
100
1000
Figure 8 - Peak Forward Voltage Drop vs Peak Forward
Current (Typical Values)
100.0
Single die
60
I F- Peak Forward Current (A)
IFSM - Peak Forward Surve Current (A)
70
1
TP - Pulse Duration (s)
50
40
30
20
Stacked-die
10.0
1.0
10
0.1
0
1
10
Number of Cycles at 60 Hz
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
100
0.0
1.0
2.0
3.0
4.0
5.0
6.0
VF - Peak Forward Voltage (V)
7.0
8.0
9.0
Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
Soldering Parameters
Lead–free
assembly
Pre Heat
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus Temp (TA)
to peak
3°C/second max
TS(max) to TA - Ramp-up Rate
3°C/second max
Reflow
- Temperature (TA) (Liquidus)
217°C
- Time (min to max) (ts)
60 – 150 seconds
Peak Temperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
260°C
Physical Specifications
tp
TP
Ramp-up
TL
Temperature (T)
Reflow Condition
tL
Critical Zone
TL to TP
Ts(max)
Ramp-down
Ts(min)
ts
Preheat
25˚C
t 25˚C to Peak
Time (t)
Environmental Specifications
High Temp. Storage
JESD22-A103
HTRB
JESD22-A108
Weight
0.002 ounce, 0.061 gram
Temperature Cycling
JESD22-A104
Case
JEDEC DO-214AC Molded Plastic over
glass passivated junction
MSL
JEDEC-J-STD-020, Level 1
Polarity
olor band denotes cathode except
C
Bipolar
H3TRB
JESD22-A101
Terminal
Matte Tin-plated leads, Solderable per
JESD22-B102
RSH
JESD22-A111
Dimensions
DO-214AC (SMA)
Cathode Band
(for Uni-directional products only)
C
A
B
H
D
F
E
J
G
K
L
I
Dimensions
Inches
Millimeters
Min
Max
Min
Max
A
0.049
0.065
1.250
1.650
B
0.157
0.181
3.990
4.600
C
0.095
0.110
2.400
2.790
D
0.075
0.090
1.900
2.290
E
0.030
0.060
0.780
1.520
F
-
0.008
-
0.203
G
0.189
0.208
4.800
5.280
H
0.006
0.012
0.152
0.305
I
0.070
-
1.800
-
J
0.082
-
2.100
-
K
-
0.090
-
2.300
L
0.082
-
2.100
-
Solder Pads
(all dimensions in mm)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 400W > SMAJ series
Part Numbering System
Part Marking System
SMAJ XXX C A
Cathode Band
F
(for Uni-directional products only)
5% VBR VOLTAGE TOLERANCE
Littelfuse Logo
XX
BI-DIRECTIONAL
YMXXX
VR VOLTAGE
SERIES
Marking Code
Trace Code Marking
Y:Year Code
M: Month Code
XXX: Lot Code
Packaging
Part number
Component
Package
SMAJ-xxxXX
DO-214AC
Packaging
Option
Quantity
5000
Tape & Reel - 12mm tape/13” reel
Packaging
Specification
EIA STD RS-481
Tape and Reel Specification
0.157
(4.0)
Cathode
0.47
(12.0)
0.157
(4.0)
0.059 DIA
(1.5)
Cover tape
13.0 (330)
0.80 (20.2)
Arbor Hole Dia.
0.49
(12.5)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Dimensions are in inches
(and millimeters).
Direction of Feed