KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Overview The KEMET Organic Capacitor (KO-CAP) is a solid electrolytic capacitor with a conductive polymer cathode capable of delivering very low ESR and improved capacitance retention at high frequencies. KO-CAP combines the low ESR of multilayer ceramic, the high capacitance of aluminum electrolytic and the volumetric efficiency of tantalum into a single surface mount package. Unlike liquid electrolyte-based capacitors, KO-CAP has a very long operational life and high ripple current capabilities. The T521 High Voltage Polymer Electrolytic is designed for higher application voltages than the T520 KO-CAP. Developed for use on 12, 24, 28 and 48 volt DC voltage rails. The low ESR of the T521 provides high ripple current capability. KO-CAP's long-life reliability enables the T521 to be an ideal alternative to liquid-based electrolytic capacitors. Benefits • Low ESR • Volumetrically efficient • Stable temperature characteristics • High ripple current capability • High reliability • 100% surge current tested • Low profile design • Halogen-Free Epoxy/RoHS Compliant Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Applications Typical applications include DC/DC converters, power supply input and higher voltage applications such as 12 V to 50 V power input rails in the military/aerospace and industrial markets. Environmental Compliance RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn or Ni-Pd-Au One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 1 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC K-SIM For a detailed analysis of specific part numbers, please visit ksim.kemet.com to access KEMET’s K-SIM software. KEMET K-SIM is designed to simulate behavior of components with respect to frequency, ambient temperature, and DC bias levels. Ordering Information Ordering Information T 521 V 226 Capacitor Class Series Case Size Capacitance Code (pF) 521 = High Voltage Polymer B, T, D, Q, V, W, X First two digits represent significant figures. Third digit specifies number of zeros. T= Tantalum M 025 A Capacitance Rated Voltage Failure Rate/ Tolerance (VDC) Design M = ±20% 12R = 12.5 016 = 16 020 = 20 025 = 25 035 = 35 050 = 50 063 = 63 075 = 75 A = N/A T E060 Termination Finish ESR Code T = 100% Matte Tin E = ESR (Sn) plated Last three digits H = Tin/Lead (SnPb) specify ESR in solder coated (5% mΩ. (060 = 60 mΩ) Pb minimum) P = Ni/Pd/Au plated Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Performance Characteristics Item Performance Characteristics Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range DF (120 Hz) ESR (100 kHz) Leakage Current −55°C to 105°C/125°C (Refer to part number for maximum temperature rating) 4.7 – 330 µF at 120 Hz/25°C M Tolerance (20%) 12.5 – 75 V ≤ 10% - Refer to Part Number Electrical Specification Table Refer to Part Number Electrical Specification Table ≤ 0.1 CV (µA) at rated voltage after 5 minutes © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 2 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Qualification Test Condition Characteristics Δ C/C Endurance Storage Life Humidity Temperature Stability 105°C at rated voltage, 2,000 hours 125°C at 2/3 rated voltage, 2,000 hours** 105°C at 0 volts, 2,000 hours 125°C at 0 voltage, 2,000 hours** 60° C, 90% RH, 500 hours, No Load Extreme temperature exposure at a succession of continuous steps at +25°C, −55°C, +25°C, +85°C, +105°/125°C, +25°C DF Within initial limits DCL IL at 105°C, 2 x IL at 125°C ESR 2 x Initial Limit Δ C/C Within -20%/+10% of initial value DF Within initial limits DCL IL at 105°C, 2 x IL at 125°C ESR 2 x Initial Limit Δ C/C Within -5%/+35% of initial value DF Within initial limits DCL Within 3.0 x initial limit +25°C −55°C +85°C +105º/125°C Δ C/C IL* ±20% ±20% ±30% DF IL IL 1.2 x IL 1.5 x IL N/A 10 x IL 10 x IL DCL IL Δ C/C Surge Voltage Mechanical Shock/Vibration Within -20%/+10% of initial value 105°C, 1.32 x rated voltage, 33 Ω Resistance, 1,000 cycles MIL–STD–202, Method 213, Condition I, 100 G peak. MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz, 20 G peak Within -20%/+10% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits Δ C/C Within ±10% of initial value DF Within initial limits DCL Within initial limits *IL = Initial limit **Refer to part number specifications for individual temperature classification. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 3 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Electrical Characteristics Capacitance vs. Frequency ESR vs. Frequency 100 1 Capacitance (µF) 10 Impedance, ESR (Ohms) 100 T521V476M020ATE055_Imp T521V336M025ATE060_Imp T521V156M035ATE100_Imp T521V476M020ATE055_ESR T521V336M025ATE060_ESR T521V156M035ATE100_ESR 0.1 0.01 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 10 1 T521V476M020ATE055 T521V336M025ATE060 T521V156M035ATE100 100 10,000,000 1,000 10,000 100,000 1,000,000 10,000,000 Frequency (Hz) Dimensions – Millimeters (Inches) Metric will govern CATHODE (-) END VIEW SIDE VIEW ANODE (+) END VIEW BOTTOM VIEW A B W B Glue pad shape/design at KEMET's option H X T S S Case Size KEMET EIA B 3528-21 T 3528-12 D 7343–31 Q 7343-12 V 7343–20 W 7343–15 X 7343–43 Termination cutout at KEMET's option, either end P R L Total Weight Component Dimensions L W H 3.5 ±0.2 (0.138 ±0.008) 3.5 ±0.2 (0.138 ±0.008) 7.3 ±0.3 (0.287 ±0.012) 7.3 ±0.3 (0.287 ±0.012) 7.3 ±0.3 (0.287 ±0.012) 7.3 ±0.3 (0.287 ±0.012) 7.3 ±0.3 (0.287 ±0.012) 2.8 ±0.2 (0.110 ±0.008) 2.8 ±0.2 (0.110 ±0.008) 4.3 ±0.3 (0.169 ±0.012) 4.3 ±0.3 (0.169 ±0.012) 4.3 ±0.3 (0.169 ±0.012) 4.3 ±0.3 (0.169 ±0.012) 4.3 ±0.3 (0.169 ±0.012) 1.9 ±0.1 (0.075 ±0.004) 1.1 ±0.1 (0.043 ±0.004) 2.8 ±0.3 (0.110 ±0.012) 1.1 ±0.1 (0.043 ±0.004) 1.9 ±0.1 (0.075 ±0.004) 1.4 ±0.1 (0.055 ±0.004) 4.0 ±0.3 (0.157 ±0.012) F ±0.1 S ±0.3 B ±0.15 (Ref) ±(0.004) ±(0.012) ±0.006 2.2 (0.087) 0.8 (0.031) 0.4 (0.016) 2.2 (0.087) 0.8 (0.031) N/A F X (Ref) P (Ref) 0.10 ±0.10 0.5 (0.020) (0.004 ±0.004) 0.05 (0.002) N/A 0.10 ±0.10 0.9 (0.035) (0.004 ±0.004) A (Minimum) (mg) 1.1 (0.043) 94.85 0.13 (0.005) 1.1 (0.043) 54.84 1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 434.83 R (Ref) T (Ref) 1.0 (0.039) 0.13 (0.005) N/A 2.4 (0.094) 1.3 (0.051) 0.5 (0.020) 2.4 (0.094) 1.3 (0.051) N/A 0.05 (0.002) N/A N/A 0.13 (0.005) 3.8 (0.150) 170.35 2.4 (0.094) 1.3 (0.051) N/A 0.05 (0.002) N/A N/A 0.13 (0.005) 3.8 (0.150) 274.30 2.4 (0.094) 1.3 (0.051) N/A 0.05 (0.002) N/A N/A 0.13 (0.005) 3.8 (0.150) 222.95 1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 553.96 2.4 (0.094) 1.3 (0.051) 0.5 (0.020) 0.10 ±0.10 1.7 (0.067) (0.004 ±0.004) Notes: (Ref) – Dimensions provided for reference only. For low profile cases, no dimensions are provided for B, P or R because these cases do not have a bevel or a notch. These weights are provided as reference. If exact weights are needed, please contact your KEMET Sales Representative © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 4 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Table 1 – Ratings & Part Number Reference Rated Voltage Rated Case Code/ Capacitance Case Size KEMET Part Number DC Leakage DF ESR % at 25°C 120 Hz Maximum 8 8 8 10 8 8 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 8 10 8 10 9 9 10 10 10 10 10 10 10 8 8 8 % at 25°C 120 Hz Maximum mΩ at 25°C 100 kHz Maximum 90 100 90 40 90 45 50 40 45 40 55 70 80 40 45 55 70 90 40 50 90 50 50 50 40 80 35 50 25 50 100 90 90 90 40 45 90 80 55 55 40 55 55 100 100 60 mΩ at 25°C 100 kHz Maximum DF ESR VDC at 105ºC µF KEMET/EIA (See below for part options) 12.5 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 20 20 20 20 20 20 20 20 20 20 20 20 20 25 25 25 47 10 15 33 22 33 33 47 47 47 47 47 47 47 47 47 47 47 68 68 68 100 100 150 150 150 220 220 330 330 10 15 22 22 47 47 47 47 47 47 47 100 100 10 10 10 T/3528-12 B/3528-21 B/3528-21 Q/7343-12 B/3528-21 T/3528-12 T/3528-12 W/7343-15 W/7343-15 V/7343-20 V/7343-20 V/7343-20 V/7343-20 D/7343-31 D/7343-31 D/7343-31 D/7343-31 D/7343-31 V/7343-20 V/7343-20 V/7343-20 V/7343-20 D/7343-31 D/7343-31 D/7343-31 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 B/3528-21 B/3528-21 B/3528-21 V/7343-20 W/7343-15 W/7343-15 V/7343-20 V/7343-20 V/7343-20 D/7343-31 D/7343-31 V/7343-20 D/7343-31 B/3528-21 T/3528-12 T/3528-12 T521T476M12RA(1)E090 T521B106M016A(1)E100 T521B156M016A(1)E090 T521Q336M016A(1)E040 T521B226M016A(1)E090 T521T336M016A(1)E045 T521T336M016A(1)E050 T521W476M016A(1)E040 T521W476M016A(1)E045 T521V476M016A(1)E040 T521V476M016A(1)E055 T521V476M016A(1)E070 T521V476M016A(1)E080 T521D476M016A(1)E040 T521D476M016A(1)E045 T521D476M016A(1)E055 T521D476M016A(1)E070 T521D476M016A(1)E090 T521V686M016A(1)E040 T521V686M016A(1)E050 T521V686M016A(1)E090 T521V107M016A(1)E050 T521D107M016A(1)E050 T521D157M016A(1)E050 T521D157M016A(1)E040 T521X157M016A(1)E080 T521X227M016A(1)E035 T521X227M016A(1)E050 T521X337M016A(1)E025 T521X337M016A(1)E050 T521B106M020A(1)E100 T521B156M020A(1)E090 T521B226M020A(1)E090 T521V226M020A(1)E090 T521W476M020A(1)E040 T521W476M020A(1)E045 T521V476M020A(1)E090 T521V476M020A(1)E080 T521V476M020A(1)E055 T521D476M020A(1)E055 T521D476M020A(1)E040 T521V107M020A(1)E055 T521D107M020A(1)E055 T521B106M025A(1)E100 T521T106M025A(1)E100 T521T106M025A(1)E060 VDC at 105ºC µF KEMET/EIA (See below for part options) µA at 25°C Maximum/5 Minutes 58.8 16.0 24.0 52.8 35.2 52.8 52.8 75.2 75.2 75.2 75.2 75.2 75.2 75.2 75.2 75.2 75.2 75.2 108.8 108.8 108.8 160.0 160.0 240.0 240.0 240.0 352.0 352.0 528.0 528.0 20.0 30.0 44.0 44.0 94.0 94.0 94.0 94.0 94.0 94.0 94.0 200.0 200.0 25.0 25.0 25.0 µA at 25°C Maximum/5 Minutes Rated Voltage Rated Capacitance Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current MSL Maximum Operating Temp mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC 1080 1100.0 1200.0 2500.0 1200.0 1500.0 1400.0 2100.0 2000.0 2200.0 1800.0 1600.0 1500.0 2400.0 2200.0 2000.0 1800.0 1600.0 2200.0 1900.0 1400.0 1900.0 2100.0 2100.0 2400.0 1800.0 2700.0 2200.0 3100.0 2200.0 1100.0 1200.0 1200.0 1400.0 2100.0 2000.0 1400.0 1500.0 1800.0 2000.0 2400.0 1800.0 2000.0 1100.0 1000.0 1300.0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 105 125 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 125 105 105 105 105 125 125 125 125 105 105 105 125 105 105 125 125 125 125 125 125 105 105 125 125 mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC Maximum Allowable Ripple Current MSL Maximum Operating Temp Other part number options: 1- Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 5 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Table 1 – Ratings & Part Number Reference cont'd Rated Voltage Rated Case Code/ Capacitance Case Size KEMET Part Number DC Leakage DF ESR % at 25°C 120 Hz Maximum 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 % at 25°C 120 Hz Maximum mΩ at 25°C 100 kHz Maximum 90 40 40 45 60 90 60 40 40 60 70 40 60 30 60 90 120 100 125 40 60 65 30 70 70 90 70 90 70 90 70 90 90 120 90 90 70 50 35 90 75 50 75 50 300 75 mΩ at 25°C 100 kHz Maximum DF ESR VDC at 105ºC µF KEMET/EIA (See below for part options) 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 63 63 15 15 22 22 22 22 33 33 33 33 68 100 100 100 100 6.8 10 15 15 22 22 33 47 47 5.6 5.6 5.6 5.6 6.8 6.8 6.8 6.8 10 10 10 18 18 18 18 22 22 22 33 33 4.7 4.7 V/7343-20 V/7343-20 V/7343-20 V/7343-20 V/7343-20 V/7343-20 V/7343-20 V/7343-20 D/7343-31 D/7343-31 D/7343-31 D/7343-31 D/7343-31 X/7343-43 X/7343-43 T/3528-12 V/7343-20 V/7343-20 V/7343-20 D/7343-31 D/7343-31 D/7343-31 X/7343-43 X/7343-43 D/7343-31 D/7343-31 V/7343-20 V/7343-20 D/7343-31 D/7343-31 V/7343-20 V/7343-20 D/7343-31 D/7343-31 V/7343-20 D/7343-31 X/7343-43 X/7343-43 X/7343-43 D/7343-31 X/7343-43 X/7343-43 X/7343-43 X/7343-43 D/7343-31 D/7343-31 T521V156M025A(1)E090 T521V156M025A(1)E040 T521V226M025A(1)E040 T521V226M025A(1)E045 T521V226M025A(1)E060 T521V226M025A(1)E090 T521V336M025A(1)E060 T521V336M025A(1)E040 T521D336M025A(1)E040 T521D336M025A(1)E060 T521D686M025A(1)E070 T521D107M025A(1)E040 T521D107M025A(1)E060 T521X107M025A(1)E030 T521X107M025A(1)E060 T521T685M035APE090 T521V106M035A(1)E120 T521V156M035A(1)E100 T521V156M035A(1)E125 T521D226M035A(1)E040 T521D226M035A(1)E060 T521D336M035A(1)E065 T521X476M035A(1)E030 T521X476M035A(1)E070 T521D565M050A(1)E070 T521D565M050A(1)E090 T521V565M050A(1)E070 T521V565M050A(1)E090 T521D685M050A(1)E070 T521D685M050A(1)E090 T521V685M050A(1)E070 T521V685M050A(1)E090 T521D106M050A(1)E090 T521D106M050A(1)E120 T521V106M050A(1)E090 T521D186M050A(1)E090 T521X186M050A(1)E070 T521X186M050A(1)E050 T521X186M050A(1)E035 T521D226M050A(1)E090 T521X226M050A(1)E075 T521X226M050A(1)E050 T521X336M050A(1)E075 T521X336M050A(1)E050 T521D475M063A(1)E300 T521D475M063A(1)E075 VDC at 105ºC µF KEMET/EIA (See below for part options) µA at 25°C Maximum/5 Minutes 37.5 37.5 55.0 55.0 55.0 55.0 82.5 82.5 82.5 82.5 170.0 250.0 250.0 250.0 250.0 23.8 35.0 52.5 52.5 77.0 77.0 115.5 164.5 164.5 28 28 28 28 34.0 34.0 34.0 34.0 50.0 50.0 50.0 90.0 90.0 90.0 90.0 110.0 110.0 110.0 165.0 165.0 29.6 29.6 µA at 25°C Maximum/5 Minutes Rated Voltage Rated Capacitance Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current MSL Maximum Operating Temp mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC 1400.0 2200.0 2200.0 2000.0 1800.0 1400.0 1800.0 2200.0 2400.0 1900.0 1800.0 2400.0 1900.0 2900.0 2000.0 1100.0 1200.0 1400.0 1200.0 2400.0 1900.0 1900.0 2900.0 1900.0 1800 1600 1800 1600 1800.0 1600.0 1800.0 1600.0 1600.0 1369.0 1600.0 1600.0 1900.0 2200.0 2700.0 1600.0 1815.0 2200.0 1815.0 2200.0 900.0 1700.0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC Maximum Allowable Ripple Current MSL Maximum Operating Temp Other part number options: 1- Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 6 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Table 1 – Ratings & Part Number Reference cont'd Rated Voltage Rated Case Code/ Capacitance Case Size KEMET Part Number DC Leakage DF ESR % at 25°C 120 Hz Maximum 10 10 10 10 10 10 % at 25°C 120 Hz Maximum mΩ at 25°C 100 kHz Maximum 50 35 150 75 50 35 mΩ at 25°C 100 kHz Maximum DF ESR VDC at 105ºC µF KEMET/EIA (See below for part options) 63 63 63 75 75 75 10 15 15 4.7 10 15 X/7343-43 X/7343-43 X/7343-43 D/7343-31 X/7343-43 X/7343-43 T521X106M063A(1)E050 T521X156M063A(1)E035 T521X156M063A(1)E150 T521D475M075A(1)E075 T521X106M075A(1)E050 T521X156M075A(1)E035 VDC at 105ºC µF KEMET/EIA (See below for part options) µA at 25°C Maximum/5 Minutes 63.0 94.5 94.5 35.3 75 112.5 µA at 25°C Maximum/5 Minutes Rated Voltage Rated Capacitance Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current MSL Maximum Operating Temp mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC 2200.0 2600.0 1300.0 1700.0 2200 2600 3 3 3 3 3 3 125 125 125 125 125 125 mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC Maximum Allowable Ripple Current MSL Maximum Operating Temp Other part number options: 1- Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 7 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Derating Guidelines 100% 95% 90% 85% 80% 75% 70% 65% 60% 55% 50% -55 Maximum Recommended Transient Voltage (1 ms – 1 µs) % Rated Voltage Voltage Rating Maximum Recommended Steady State Voltage −55°C to 105°C 12.5 V ≤ VR ≤ 75 V 80% of VR VR 105°C to 125°C 12.5 V ≤ VR ≤ 75 V 54% of VR 67% of VR VR = Rated Voltage Maximum Transient Voltage Recommended Application Voltage 25 45 85 Temperature (°C) 105 125 Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage which may be applied is limited by two criteria: 1. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. 2. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. See the Reverse Voltage section for allowable limits. The maximum power dissipation by case size can be determined using the table at right. The maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the table below for temperature compensation requirements. Case Code EIA Case Code T B W V D Q X 3528-12 3528-21 7343-15 7343-20 7343-31 7343-12 7343-43 Maximum Power Dissipation (P max) mWatts at 45°C with +30°C Rise 105 127 180 187 225 170 247 The maximum power dissipation rating must be reduced with increasing environmental operating temperatures. Refer to the Temperature Compensation Multiplier table for details. Temperature Compensation Multipliers for Maximum Ripple Current T ≤ 45°C 1.00 45° C < T ≤ 85°C 0.70 85°C < T ≤ 125°C 0.25 T= Environmental Temperature Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = √P max/R E(max) = Z √P max/R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation (watts) R = ESR at specified frequency (ohms) Z = Impedance at specified frequency (ohms) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 8 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Reverse Voltage Polymer electrolytic capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. Temperature Permissible Transient Reverse Voltage 25°C 55°C 85°C 105°C 125°C* 15% of Rated Voltage 10% of Rated Voltage 5% of Rated Voltage 3% of Rated Voltage 1% of Rated Voltage *For series rated to 125°C Table 2 – Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case EIA W L S V1 V2 W L S V1 V2 W L S V1 V2 B 3528–21 2.35 2.21 0.92 6.32 4.00 2.23 1.80 1.12 5.22 3.50 2.13 1.42 1.28 4.36 3.24 D 7343–31 2.55 2.77 3.67 10.22 5.60 2.43 2.37 3.87 9.12 5.10 2.33 1.99 4.03 8.26 4.84 Q 7343-12 2.55 2.77 3.67 10.22 5.60 2.43 2.37 3.87 9.12 5.10 2.33 1.99 4.03 8.26 4.84 T 3528–12 2.35 2.20 0.92 6.32 4.00 2.23 1.80 1.12 5.22 3.50 2.13 1.42 1.28 4.36 3.24 V 7343–20 2.55 2.77 3.67 10.22 5.60 2.43 2.37 3.87 9.12 5.10 2.33 1.99 4.03 8.26 4.84 W 7343–15 2.55 2.77 3.67 10.22 5.60 2.43 2.37 3.87 9.12 5.10 2.33 1.99 4.03 8.26 4.84 X1 7343–43 2.55 2.77 3.67 10.22 5.60 2.43 2.37 3.87 9.12 5.10 2.33 1.99 4.03 8.26 4.84 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC–7351). ¹ Height of these chips may create problems in wave soldering. 2 Land pattern geometry is too small for silkscreen outline. V1 L L W W V2 S Grid Placement Courtyard © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 9 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Soldering Process KEMET’s families of surface mount capacitors are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J–STD–020D standard for moisture sensitivity testing. The devices can safely withstand a maximum of three reflow passes at these conditions. Please note that although the X/7343–43 case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. SnPb Assembly Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) 100°C 150°C Temperature Maximum (TSmax) 150°C 200°C Time (ts) from Tsmin to Tsmax) 60 – 120 seconds 60 – 120 seconds Ramp-up Rate (TL to TP) 3°C/seconds maximum 3°C/seconds maximum Liquidous Temperature (TL) 183°C 217°C Time Above Liquidous (tL) 60 – 150 seconds 220°C* 235°C** 60 – 150 seconds 250°C* 260°C** Peak Temperature (TP) Time within 5°C of Maximum Peak Temperature (tP) Ramp-down Rate (TP to TL) 20 seconds maximum 30 seconds maximum 6°C/seconds maximum 6°C/seconds maximum Time 25°C to Peak Temperature 6 minutes maximum 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. *Case Size D, E, P, Y, and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z TP TL Temperature Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case. The iron should be used to heat the solder pad, applying solder between the pad and the termination, until reflow occurs. Once reflow occurs, the iron should be removed immediately. “Wiping” the edges of a chip and heating the top surface is not recommended. Profile Feature tP Maximum Ramp Up Rate = 3ºC/seconds Maximum Ramp Down Rate = 6ºC/seconds tL Tsmax Tsmin 25 tS 25ºC to Peak Time Storage All KO-CAP series are shipped in moisture barrier bags with a desiccant and moisture indicator card. These series are classified as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working environments with temperatures not to exceed 40°C and humidity not in excess of 90% RH. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 10 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Construction Molded Epoxy Case Detailed Cross Section Polarity Stripe (+) Silver Paint (Fourth Layer) Polarity Bevel (+) Wire Leadframe (- Cathode) Wire Weld (to attach wire) Carbon (Third Layer) Silver Adhesive Leadframe (+ Anode) Molded Epoxy Case Polymer (Second Layer) Ta2O5 Dielectric (First Layer) Tantalum Capacitor Marking Date Code * KEMET Organic Polymer Polarity Indicator (+) 1 digit = Last number of Year 2 = 2012 3 = 2013 4 = 2014 5 = 2015 6 = 2016 7 = 2017 2nd and 3rd digit = Week of the Year 01 = 1st week of the Year to 52 = 52nd week of the Year st Picofarad Code KEMET ID Rated Voltage Date Code* * 230 = 30th week of 2012 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 11 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Tape & Reel Packaging Information KEMET’smoldedchipcapacitorfamiliesarepackagedin8and12mmplastictapeon7"and13"reelsinaccordancewithEIA Standard 481: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape-fed automatic pick-and-place systems. 8 mm (0.315") or 12 mm (0.472") Top Tape Thickness 0.10 mm (0.004") Maximum Thickness 180 mm (7.0") or 330 mm (13.0") Table 3 – Packaging Quantity Case Code KEMET R I S T M U L W Z Q V A B C D Y X E/T428P H EIA 2012-12 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-12 7343-19 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7360-38 7360-20 Tape Width (mm) 7" Reel* 13" Reel* 8 8 8 8 8 12 12 12 12 12 12 8 8 12 12 12 12 12 12 2,500 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 1,000 10,000 12,000 10,000 10,000 8,000 5,000 3,000 3,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 3,000 * No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging. * A case with black epoxy only available in 7" reel © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 12 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØDo Po [10 pitches cumulative tolerance on tape ± 0.2 mm] E1 Ao F Ko B1 S1 W E2 Bo P1 T1 Center Lines of Cavity B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 ØD 1 Cover Tape User Direction of Unreeling Table 4 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) B1 Maximum Note 4 4.35 (0.171) E1 P0 1.75 ±0.10 (0.069 ±0.004) 4.0 ±0.10 (0.157 ±0.004) P2 2.0 ±0.05 (0.079 ±0.002) 2.0 ±0.1 (0.079 ±0.059) R Reference Note 2 25.0 (0.984) 30 (1.181) S1 Minimum T Maximum T1 Maximum Note 3 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) Variable Dimensions — Millimeters (Inches) Tape Size Pitch E2 Minimum F 8 mm Single (4 mm) 6.25 (0.246) 3.5 ±0.05 (0.138 ±0.002) 12 mm Single (4 mm) & Double (8 mm) 8.2 (0.323) 10.25 (0.404) 16 mm Triple (12 mm) 12.1 (0.476) 14.25 (0.561) P1 2.0 ±0.05 or 4.0 ±0.10 (0.079 ±0.002 or 0.157 ±0.004) 2.0 ±0.05 (0.079 ±0.002) or 4.0 5.5 ±0.05 ±0.10 (0.157 ±0.004) or 8.0 ±0.10 (0.217 ±0.002) (0.315 ±0.004) 7.5±0.10 4.0 ±0.10 (0.157 ±0.004) to 12.0 (0.295 ±0.004) ±0.10 (0.472 ±0.004) T2 Maximum W Maximum A0, B0 & K0 2.5 (0.098) 8.3 (0.327) 4.6 (0.181) 12.3 (0.484) 8.0 (0.315) 16.3 (0.642) Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape, with or without components, shall pass around R without damage (see Figure 4). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 13 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 – 200 Bo Maximum Rotation ( 20 10 ° T) Typical Component Centerline Ao Figure 3 – Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape ° s Tape Maximum Width (mm) Rotation ( 8,12 20 16 – 56 10 72 – 200 5 ° S) Figure 4 – Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com R T2016_T521 • 4/4/2016 14 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Figure 5 – Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (Ø 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 5 – Reel Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 ±0.20 (7.008 ±0.008) or 330 ±0.20 (13.000 ±0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions — Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 15 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Figure 6 – Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 7 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 16 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC KEMET Corporation World Headquarters Europe Asia Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel: 389-2-55-14-623 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Wyboston, United Kingdom Tel: 44-1480-273082 Taipei, Taiwan Tel: 886-2-27528585 Espoo, Finland Tel: 358-9-5406-5000 Southeast Asia Singapore Tel: 65-6701-8033 2835 KEMET Way Simpsonville, SC 29681 Northeast Wilmington, MA Tel: 978-658-1663 Southeast Lake Mary, FL Tel: 407-855-8886 Central Novi, MI Tel: 248-994-1030 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Irving, TX Tel: 972-915-6041 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 17 KEMET Organic Capacitor (KO-CAP®) – Industrial T521 High Voltage Polymer Electrolytic, 12.5 – 75 VDC Disclaimer Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise providedbyKEMETwithreferencetotheuseofKEMET’sproductsisgivengratis,andKEMETassumesnoobligationorliabilityfortheadvicegivenorresultsobtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016_T521 • 4/4/2016 18