KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Overview The KEMET Organic Capacitor (KO-CAP) is a solid electrolytic capacitor with a conductive polymer cathode capable of delivering very low ESR and improved capacitance retention at high frequencies. KO-CAP combines the low ESR of multilayer ceramic, the high capacitance of aluminum electrolytic and the volumetric efficiency of tantalum into a single surface mount package. Unlike liquid electrolyte-based capacitors, KO-CAP has a very long operational life and high ripple current capabilities. The T528 Low ESL Facedown Terminal Polymer Electrolytic combines ultra-low ESR and high capacitance in a package design that offers the lowest ESL in the market. This series offers exceptional performance for high-speed microprocessor, FPGA or ASIC decoupling designs. The T528 Series utilizes a unique termination design that allows for a reduction in the inductance loop area and comes in a low profile 1.7 mm case height. This capacitor series offers improved capacitance retention at frequencies of up to 1 MHz. Benefits • • • • • • • • Low ESL <0.7 nH at 20 MHz Improved volumetric efficiency High frequency capacitance retention 100% accelerated steady state aging 100% surge current tested EIA standard case sizes Halogen-Free Epoxy/RoHS Compliant Lead free 260°C reflow capable Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Applications Typical applications include high speed server, microprocessor decoupling and high ripple current applications. Environmental Compliance RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn or Ni-Pd-Au. K-SIM For a detailed analysis of specific part numbers, please visit ksim.kemet.com to access KEMET’s K-SIM software. KEMET K-SIM is designed to simulate behavior of components with respect to frequency, ambient temperature, and DC bias levels. One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 1 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Ordering Information T 528 Z 337 M Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance 528 = Low ESL Facedown Terminal Polymer B = 3528-21 W = 7343-15 Z = 7343-17 First two digits represent significant figures. Third digit specifies number of zeros. M = ±20% T= Tantalum 2R5 A Rated Voltage Failure Rate/ (VDC) Design 002 = 2 2R5 = 2.5 004 = 4 006 = 6.3 A = N/A T E009 Termination Finish ESR Code T = 100% Matte Tin (Sn) plated P = Ni-Pd-Au plated E = ESR Last three digits specify ESR in mΩ (009 = 9 mΩ) Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Performance Characteristics Item Performance Characteristics Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range DF (120 Hz) ESR (100 kHz) Leakage Current −55°C to 105°C 33 – 470 µF at 120 Hz/25°C M Tolerance (20%) 2 – 6.3 V ≤ 10% Refer to Part Number Electrical Specification Table ≤ 0.1 CV (µA) at rated voltage after 5 minutes © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 2 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Qualification Test Condition Characteristics Δ C/C Endurance Storage Life Humidity Temperature Stability 105°C at rated voltage, 2,000 hours 105°C at 0 volts, 2,000 hours 60°C, 90% RH, 500 hours Extreme temperature exposure at a succession of continuous steps at +25°C, −55°C, +25°C, +85°C, +105°C, +25°C Δ C/C DF ≤ Initial Limit DCL Within 1.25 x initial limit ESR Within 2.0 x initial limit Δ C/C Within -20/+10% of initial value DF Within initial limits DCL Within 1.25 x initial limit ESR Within 2.0 x initial limit Δ C/C Within -5/+35% of initial value DF ≤ Initial Limit DCL Within 5.0 x initial limit ESR Within 2.0 x initial limit +25°C −55°C +85°C +105°C IL* ±20% ±20% ±30% DF IL IL 1.2 x IL 1.5 x IL DCL IL N/A 10 x IL 10 x IL Δ C/C Surge Voltage Mechanical Shock/Vibration Within -20/+10% of initial value 105°C, 1.32 x rated voltage 1,000 cycles MIL–STD–202, Method 213, Condition I, 100 G peak MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz, 20 G peak Within -20/+10% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits Δ C/C Within ±10% of initial value DF Within initial limits DCL Within initial limits *IL = Initial limit © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 3 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Electrical Characteristics Capacitance vs. Frequency ESR vs. Frequency 1000 10 T528Z337M2R5ATE009_Imp 1 T528Z337M2R5ATE007_Imp T528Z337M2R5ATE012_ESR Capacitance (µF) Impedance, ESR (Ohms) T528Z337M2R5ATE012_Imp T528Z337M2R5ATE009_ESR T528Z337M2R5ATE007_ESR 0.1 100 10 0.01 T528Z337M2R5ATE012 T528Z337M2R5ATE009 T528Z337M2R5ATE007 0.001 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 1 1,000 10,000,000 10,000 100,000 Frequency (Hz) 1,000,000 10,000,000 Dimensions – Millimeters END VIEW BOTTOM VIEW SIDE VIEW H (–) L W (+) F Termination cutout at KEMET's option, either end S2 S1 Case Size Total Weight Component Dimensions KEMET EIA L W B 3528–20 3.5 ±0.2 2.8 ±0.2 W 7343–15 7.3 ±0.4 4.3 ±0.3 Z 7343–17 7.3 ±0.4 4.3 ±0.3 H 2.0 Maximum 1.5 Maximum 1.7 Maximum F ±0.2 S1 ±0.4 S2 ±0.2 (mg) 2.2 0.8 0.8 94.85 2.8 5.0 1.3 222.95 2.8 5.0 1.3 206.33 These weights are provided as reference. If exact weights are needed, please contact your KEMET Sales Representative © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 4 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Table 1 – Ratings & Part Number Reference Rated Rated Case Code/ Voltage Capacitance Case Size Maximum Allowable Ripple Current MSL Maximum Operating Temp mΩ at +25ºC 100 kHz Maximum 6 9 6 6 9 9 5 6 7 8 9 12 5 6 8 9 12 7 8 9 12 9 12 7 8 9 12 9 12 mA at +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC 3900 3200 7400 3900 3200 6000 8100 7400 6800 6400 6000 5200 8100 7400 6400 6000 5200 6800 6400 6000 5200 6000 5200 6800 6400 6000 5200 6000 5200 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 KEMET Part Number DC Leakage DF ESR % at +25ºC 120 Hz Maximum 8 8 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 VDC at 105ºC µF KEMET/EIA (See below for part options) 2 2 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 270 270 220 270 270 330 330 330 330 330 330 330 470 470 470 470 470 220 220 220 220 330 330 150 150 150 150 220 220 B/3528-21 B/3528-21 Z/7343-17 B/3528-21 B/3528-21 W/7343-15 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 Z/7343-17 T528B277M002APE006 T528B277M002APE009 T528Z227M2R5ATE006 T528B277M2R5APE006 T528B277M2R5APE009 T528W337M2R5ATE009 T528Z337M2R5ATE005 T528Z337M2R5ATE006 T528Z337M2R5ATE007 T528Z337M2R5ATE008 T528Z337M2R5ATE009 T528Z337M2R5ATE012 T528Z477M2R5ATE005 T528Z477M2R5ATE006 T528Z477M2R5ATE008 T528Z477M2R5ATE009 T528Z477M2R5ATE012 T528Z227M004ATE007 T528Z227M004ATE008 T528Z227M004ATE009 T528Z227M004ATE012 T528Z337M004ATE009 T528Z337M004ATE012 T528Z157M006ATE007 T528Z157M006ATE008 T528Z157M006ATE009 T528Z157M006ATE012 T528Z227M006ATE009 T528Z227M006ATE012 µA at +25ºC Maximum/ 5 Minutes 54.0 54.0 55.0 67.5 67.5 82.5 82.5 82.5 82.5 82.5 82.5 82.5 117.5 117.5 117.5 117.5 117.5 88.0 88.0 88.0 88.0 132.0 132.0 94.5 94.5 94.5 94.5 138.6 138.6 VDC at 105ºC µF KEMET/EIA (See below for part options) µA at +25ºC Maximum/ 5 Minutes % at +25ºC 120 Hz Maximum mΩ at +25ºC 100 kHz Maximum mA +45ºC 100 kHz Reflow Temp ≤ 260ºC ºC Rated Voltage Rated Capacitance Case Code/ Case Size KEMET Part Number DC Leakage DF ESR Maximum Allowable Ripple Current MSL Maximum Operating Temp Other part number options: 1- Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 5 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Derating Guidelines Maximum Recommended Steady State Voltage Maximum Recommended Transient Voltage (1 ms – 1 µs) −55°C to 105°C 2 V ≤ VR ≤ 6.3 V 90% of VR VR VR = Rated Voltage Maximum Transient Voltage 95% 90% 85% % Rated Voltage Voltage Rating 100% Recommended Application Voltage 80% 75% 70% 65% 60% 55% 50% -55 25 85 105 Temperature (°C) Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage which may be applied is limited by two criteria: 1. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. 2. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. See the Reverse Voltage section for allowable limits. The maximum power dissipation by case size can be determined using the table at right. The maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the table below for temperature compensation requirements. Case Code EIA Case Code B W Z 3528-20 7343-15 7343-17 Maximum Power Dissipation (P max) mWatts at 45°C with +30°C Rise 127 325 325 The maximum power dissipation rating must be reduced with increasing environmental operating temperatures. Refer to the Temperature Compensation Multiplier table for details. Temperature Compensation Multipliers for Maximum Ripple Current T ≤ 45°C 1.00 45° C < T ≤ 85°C 0.70 85°C < T ≤ 125°C 0.25 T= Environmental Temperature Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = √P max/R E(max) = Z √P max/R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation (watts) R = ESR at specified frequency (ohms) Z = Impedance at specified frequency (ohms) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 6 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Reverse Voltage Polymer electrolytic capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. Temperature Permissible Transient Reverse Voltage 25°C 55°C 85°C 105°C 125°C* 15% of Rated Voltage 10% of Rated Voltage 5% of Rated Voltage 3% of Rated Voltage 1% of Rated Voltage *For Series Rated to 125°C Table 2 – Land Dimensions/Courtyard KEMET Metric Size Code Case EIA Density Level A: Maximum (Most) Land Protrusion (mm) L1 L2 W S1 S2 V1 Density Level B: Median (Nominal) Land Protrusion (mm) V2 L1 L2 W S1 S2 Density Level C: Minimum (Least) Land Protrusion (mm) V1 V2 L1 L2 W S1 S2 V1 V2 B 3528-20 2.20 2.20 2.35 0.46 0.46 6.32 4.00 1.80 1.80 2.23 0.56 0.56 5.22 3.50 1.42 1.42 2.13 0.64 0.64 4.36 3.24 1 W 7343-15 6.48 2.68 3.04 -1.82 1.98 10.32 5.60 6.18 2.38 2.92 -1.82 1.98 9.22 5.10 5.82 2.02 2.82 -1.76 2.04 8.36 4.84 Z1 7343-17 6.48 2.68 3.04 -1.82 1.98 10.32 5.60 6.18 2.38 2.92 -1.82 1.98 9.22 5.10 5.82 2.02 2.82 -1.76 2.04 8.36 4.84 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC–7351). ¹ Negative values of S1 mean that pad lies at the center's right side. V1 W, Z Case B Case L1 L1 L2 W V2 W V1 L2 W S1 S2 W V2 S1 S2 Grid Placement Courtyard Grid Placement Courtyard © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 7 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Soldering Process KEMET’s families of surface mount capacitors are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J–STD–020D standard for moisture sensitivity testing. The devices can safely withstand a maximum of three reflow passes at these conditions. Please note that although the X/7343–43 case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. SnPb Assembly Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) 100°C 150°C Temperature Maximum (TSmax) 150°C 200°C Time (ts) from Tsmin to Tsmax) 60 – 120 seconds 60 – 120 seconds Ramp-up Rate (TL to TP) 3°C/seconds maximum 3°C/seconds maximum Liquidous Temperature (TL) 183°C 217°C Time Above Liquidous (tL) 60 – 150 seconds 220°C* 235°C** 60 – 150 seconds 250°C* 260°C** Peak Temperature (TP) Time within 5°C of Maximum Peak Temperature (tP) Ramp-down Rate (TP to TL) 20 seconds maximum 30 seconds maximum 6°C/seconds maximum 6°C/seconds maximum Time 25°C to Peak Temperature 6 minutes maximum 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. *Case Size D, E, P, Y, and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z TP TL Temperature Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case. The iron should be used to heat the solder pad, applying solder between the pad and the termination, until reflow occurs. Once reflow occurs, the iron should be removed immediately. “Wiping” the edges of a chip and heating the top surface is not recommended. Profile Feature tP Maximum Ramp Up Rate = 3ºC/seconds Maximum Ramp Down Rate = 6ºC/seconds tL Tsmax Tsmin 25 tS 25ºC to Peak Time Storage All KO-CAP series are shipped in moisture barrier bags with a desiccant and moisture indicator card. These series are classified as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working environments with temperatures not to exceed 40°C and humidity not in excess of 90% RH. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 8 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Construction Polarity Stripe (+) Detailed Cross Section Carbon (Third Layer) Silver Paint (Fourth Layer) Wire Molded Epoxy Case Wire Polymer (Second Layer) Leadframe (+ Anode) Leadframe (- Cathode) Spacer Ta2O5 Dielectric (First Layer) Tantalum Weld (to attach wire) Capacitor Marking KEMET Facedown Organic Polymer Polarity Indicator (+) Picofarad Code Rated Voltage Date Code * 1 digit = Last number of Year 2 = 2012 3 = 2013 4 = 2014 5 = 2015 6 = 2016 7 = 2017 2nd and 3rd digit = Week of the Year 01 = 1st week of the Year to 52 = 52nd week of the Year st KEMET ID Date Code* * 230 = 30th week of 2012 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 9 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Tape & Reel Packaging Information KEMET’smoldedchipcapacitorfamiliesarepackagedin8and12mmplastictapeon7"and13"reelsinaccordancewithEIA Standard 481:EmbossedCarrierTapingofSurfaceMountComponentsforAutomaticHandling.Thispackagingsystemiscompatible withalltape-fedautomaticpick-and-placesystems. 8 mm (0.315") or 12 mm (0.472") Top Tape Thickness 0.10 mm (0.004") Maximum Thickness 180 mm (7.0") or 330 mm (13.0") Table 3 – Packaging Quantity Case Code KEMET S T M U L W Z V A B C D Q Y X E/T428P H EIA 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-12 7343-40 7343-43 7360-38 7360-20 Tape Width (mm) 7" Reel* 13" Reel* 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 12 12 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 1,000 500 500 500 1,000 10,000 10,000 8,000 5,000 3,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 3,000 2,000 2,000 2,000 2,500 * No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 10 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØDo Po [10 pitches cumulative tolerance on tape ± 0.2 mm] E1 Ao F Ko B1 S1 W E2 Bo P1 T1 Center Lines of Cavity B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 ØD 1 Cover Tape User Direction of Unreeling Table 4 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note1 1.0 (0.039) 1.5 (0.059) B1 Maximum Note4 4.35 (0.171) E1 P0 1.75 ±0.10 (0.069 ±0.004) 4.0 ±0.10 (0.157 ±0.004) P2 2.0 ±0.05 (0.079 ±0.002) 2.0 ±0.1 (0.079 ±0.059) RReference Note2 25.0 (0.984) 30 (1.181) S1 Minimum T Maximum T1 Maximum Note3 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) Variable Dimensions — Millimeters (Inches) Tape Size Pitch E2 Minimum F 8 mm Single (4 mm) 6.25 (0.246) 3.5 ±0.05 (0.138 ±0.002) 12 mm Single (4 mm) & Double(8mm) 8.2 (0.323) 10.25 (0.404) 16 mm Triple (12 mm) 12.1 (0.476) 14.25 (0.561) P1 2.0 ±0.05 or 4.0 ±0.10 (0.079 ±0.002 or 0.157 ±0.004) 2.0 ±0.05 (0.079 ±0.002) or 4.0 5.5 ±0.05 ±0.10 (0.157 ±0.004) or 8.0 ±0.10 (0.217 ±0.002) (0.315 ±0.004) 7.5±0.10 4.0 ±0.10 (0.157 ±0.004) to 12.0 (0.295 ±0.004) ±0.10 (0.472 ±0.004) T2 Maximum W Maximum A0, B0 & K0 2.5 (0.098) 8.3 (0.327) 4.6 (0.181) 12.3 (0.484) 8.0 (0.315) 16.3 (0.642) Note5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape, with or without components, shall pass around R without damage (see Figure 4). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 11 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: Thetotalpeelstrengthofthecovertapefromthecarriertapeshallbe: Tape Width Peel Strength 8 mm 0.1to1.0Newton(10to100gf) 12 and 16 mm 0.1to1.3Newton(10to130gf) Thedirectionofthepullshallbeoppositethedirectionofthecarriertapetravel.Thepullangleofthecarriertapeshallbe165°to180° fromtheplaneofthecarriertape.Duringpeeling,thecarrierand/orcovertapeshallbepulledatavelocityof300±10mm/minute. 3. Labeling:Barcodelabeling(standardorcustom)shallbeonthesideofthereeloppositethesprocketholes.Refer to EIA Standards 556 and 624. Figure 2 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 – 200 Bo Maximum Rotation ( 20 10 ° T) Typical Component Centerline Ao Figure 3 – Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape ° s Tape Maximum Width (mm) Rotation ( 8,12 20 16 – 56 10 72 – 200 5 ° S) Figure 4 – Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com R T2018_T528 • 3/15/2016 12 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Figure 5 – Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (Ø 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 5 – Reel Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size A B Minimum C DMinimum 8 mm 178 ±0.20 (7.008 ±0.008) or 330 ±0.20 (13.000 ±0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions — Millimeters (Inches) Tape Size NMinimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 13 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Figure 6 – Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 7 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 14 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling KEMET Corporation World Headquarters Europe Asia Southern Europe SassoMarconi,Italy Tel:39-051-939111 Northeast Asia Hong Kong Tel:852-2305-1168 MailingAddress: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel:389-2-55-14-623 Shenzhen, China Tel:86-755-2518-1306 www.kemet.com Tel:864-963-6300 Fax:864-963-6521 Central Europe Landsberg,Germany Tel:49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel:954-766-2800 Kamen,Germany Tel:49-2307-438110 North America Northern Europe Wyboston,UnitedKingdom Tel:44-1480-273082 Taipei, Taiwan Tel:886-2-27528585 Espoo, Finland Tel:358-9-5406-5000 Southeast Asia Singapore Tel:65-6701-8033 2835KEMETWay Simpsonville, SC 29681 Northeast Wilmington, MA Tel:978-658-1663 Southeast LakeMary,FL Tel:407-855-8886 Central Novi,MI Tel:248-994-1030 Beijing, China Tel:86-10-5877-1075 Shanghai, China Tel:86-21-6447-0707 Seoul, South Korea Tel:82-2-6294-0550 Penang,Malaysia Tel:60-4-6430200 Bangalore, India Tel:91-806-53-76817 Irving, TX Tel:972-915-6041 West Milpitas, CA Tel:408-433-9950 Mexico Guadalajara, Jalisco Tel:52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 15 KEMET Organic Capacitor (KO-CAP®) – Miniature T528 Low ESL Polymer Electrolytic for CPU/GPU Decoupling Disclaimer Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand verifyingtheextenttowhichtheInformationcontainedinthispublicationisapplicabletoanorderatthetimetheorderisplaced. AllInformationgivenhereinisbelievedtobeaccurateandreliable,butitispresentedwithoutguarantee,warranty,orresponsibilityofanykind,expressedorimplied. StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly bycustomerswhohavetherequisiteexperienceandcapabilitytodeterminethecorrectproductsfortheirapplication.AnytechnicaladviceinferredfromthisInformationorotherwise providedbyKEMETwithreferencetotheuseofKEMET’sproductsisgivengratis,andKEMETassumesnoobligationorliabilityfortheadvicegivenorresultsobtained. AlthoughKEMETdesignsandmanufacturesitsproductstothemoststringentqualityandsafetystandards,giventhecurrentstateoftheart,isolatedcomponentfailuresmaystill occur.Accordingly,customerapplicationswhichrequireahighdegreeofreliabilityorsafetyshouldemploysuitabledesignsorothersafeguards(suchasinstallationofprotective circuitryorredundancies)inordertoensurethatthefailureofanelectricalcomponentdoesnotresultinariskofpersonalinjuryorpropertydamage. Althoughallproduct–relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatothermeasuresmaynot berequired. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2018_T528 • 3/15/2016 16