OKR-T/1.5-W12-C www.murata-ps.com Adjustable Output 1.5-Amp SIP-mount DC/DC Converters Typical unit FEATURES PRODUCT OVERVIEW 600 KHz operation The OKR-T/1.5-W12-C is a miniature SIP non-isolated Point-of-Load (PoL) DC/DC power converter measuring only 0.41 x 0.40 x 0.24 inches (10.4 x 10.16 x 6.1 mm). The wide input range is 4.5 to 14 Volts DC. Based on 600 KHz synchronous buck topology, the high power conversion efficient Point of Load (PoL) module features programmable output voltage and On/Off control, under voltage lock out (UVLO), overcurrent and over temperature protections. These units are certified to UL/EN/ IEC 60950-1 safety standards (2nd edition) and RoHS-6 hazardous substance compliance. 4.5-14 Vdc input voltage range Programmable output voltage from 0.591-6.0 VDC High power conversion efficiency at 93% Outstanding thermal derating performance Over temperature and over current protection On/Off control SIP, 0.41 x 0.40 x 0.24 inches (10.4 x 10.16 x 6.1 mm) Certified to UL/EN/IEC 60950-1 safety standards, 2nd edition RoHS-6 hazardous substance compliance Figure 1. Connection Diagram +Vin +Vout t4XJUDIJOH F1 Rp External DC Power Source Controller On/Off Control t'JMUFST t$VSSFOU4FOTF Trim Reference and Error Amplifier Q1 Common Common For full details go to www.murata-ps.com/rohs www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 1 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Root Model OKR-T/1.5-W12-C Input R/N (mVp-p) Regulation (Max.) IOUT VOUT (Amps Power VIN Nom. Range (Volts) max) (Watts) (Volts) (Volts) Max. Line Load 0.591-6 1.5 7.5 25 ±0.3% ±0.5% ➀ For Vout ≥ 3.3V, Vin should be ≥ (Vout ÷ 0.85) + 0.5V. 12 4.5-14 IIN, IIN, no load full load (mA) (Amps) 80 0.672 Efficiency Min. Typ. Dimensions (Inches) 91% 93% 0.41x0.40x0.24 ➂ Ripple and Noise (R/N) is shown at Vout=1V. See specs for details. ➁ All specifications are at nominal line voltage, Vout=nominal (5V for W12 models) and full load, +25°C unless otherwise noted. PART NUMBER STRUCTURE OK R - T / 1.5 - W12 - C Okami Non-isolated PoL SIP-Mount Output Voltage Range T = Trimmable, 0.591-6 Volts RoHS Hazardous Substance Compliance C = RoHS-6 (does not claim EU RoHS exemption 7b–lead in solder) Wide Input Voltage Range W12 = 4.5 – 14 Volts Maximum Rated Output Current in Amps Product Label Because of the small size of these products, the product label contains a character-reduced code to indicate the model number and manufacturing date code. Not all items on the label are always used. Please note that the label differs from the product photograph on page 1. Here is the layout of the label: Mfg. date code XXXXXX Product code YMDX Rev. Revision level Figure 2. Label Artwork Layout Model Number Product Code OKR-T/1.5-W12-C 54733 The manufacturing date code is four characters: First character – Last digit of manufacturing year, example 2009 Second character – Month code (1 through 9 = Jan-Sep; O, N, D = Oct, Nov, Dec) Third character – Day code (1 through 9 = 1 to 9, 10 = 0 and 11 through 31 = A through Z) Fourth character – Manufacturing information The label contains three rows of information: First row – Murata Power Solutions logo Second row – Model number product code (see table) Third row – Manufacturing date code and revision level www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 2 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters FUNCTIONAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Minimum Typical/Nominal Maximum Units Conditions ➀ Input Voltage, Continuous Full power operation 0 15 Vdc Input Reverse Polarity None, install external fuse None Vdc On/Off Remote Control Power on or off, referred to -Vin 0 14 Vdc Output Power 0 7.5 7.65 W Output Current Current-limited, no damage, short-circuit protected 0 1.5 A Storage Temperature Range Vin = Zero (no power) -55 125 °C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied or recommended. INPUT Operating voltage range Vin≥Vout+2V for 3.3V and 5V 4.5 12 14 Vdc Recommended External Fuse Fast blow 3 A Turn On/Start-up threshold Rising input voltage 3.9 4.2 4.4 Vdc Turn Off/Undervoltage lockout 15 Falling input voltage 3 3.4 3.7 Vdc Reverse Polarity Protection None, install external fuse None Vdc Internal Filter Type C-TYPE Input current Full Load Conditions Vin = nominal (5Vo set) 0.672 0.701 A Low Line Vin @ min, 5 Vout 1.122 1.163 A Inrush Transient 0.4 A2-Sec. Short Circuit Input Current 60 mA No Load Input Current 5Vout, Iout @ 0 80 100 mA No Load Input Current 0.59V, Iout @ 0 40 55 Shut-Down Mode Input Current 5 mA Measured at input with specified filter 20 mA, pk-pk Reflected (back) ripple current ➁ GENERAL and SAFETY @ Vin nom, 5Vout 91 93 % @ Vin min, 5Vout 94 95.5 % @ Vin nom, 3.3Vout 88.5 90 % @ Vin nom, 2.5Vout 86 88 % Efficiency @Vin nom, 1.8Vout 82.5 84.5 % @Vin nom, 1.5Vout 80 82.5 % @Vin nom, 1.2Vout 77 79 % @Vin nom, 1Vout 74 76 % Certified to UL-60950-1, IEC/EN60950-1, Safety Yes 2nd Edition Per Telcordia SR332, issue 1, class 3, ground 10.7 Hours x 106 Calculated MTBF ➃ fixed, Tambient=+25°C DYNAMIC CHARACTERISTICS Fixed Switching Frequency 600 KHz Power On to Vout regulated Startup Time 6 mS (100% resistive load) Startup Time Remote ON to 10% Vout (50% resistive load) 6 8 mS 50-100-50% load step, settling time to within Dynamic Load Response 50 100 μSec ±2% of Vout di/dt = 2.5 A/μSec Dynamic Load Peak Deviation same as above 100 200 mV FEATURES and OPTIONS Remote On/Off Control ➄ “P” suffix: a 49.2KΩ pulldown to ground needed. Positive Logic, ON state Pin open=ON 2 +Vin V Positive Logic, OFF state 0 0.2 V Control Current open collector/drain 1 mA www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 3 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) OUTPUT Total Output Power Voltage Nominal Output Voltage Range 13 Setting Accuracy Output Voltage Overshoot - Startup: Current Output Current Range Minimum Load Current Limit Inception ➅ Short Circuit Short Circuit Current ➆ Short Circuit Duration (remove short for recovery) Short circuit protection method Regulation ➉ Total Regulation Band Line Regulation Load Regulation Ripple and Noise ➇ Temperature Coefficient Maximum Capacitive Loading Maximum Capacitive Loading MECHANICAL Outline Dimensions 14 Conditions ➀ Minimum 0 See trim formula At 50% load 0.591 -2 0 98% of Vnom., after warmup @5Vout 2.65 1.5 No minimum load 4.15 Hiccup technique, autorecovery within ±1% of Vout 0.6 Output shorted to ground, no damage Continuous Maximum 7.65 Units W 6 2 1 Vdc % of Vnom. %Vo nom 1.5 A 5.15 A A Current limiting Over all line, load and temp conditions Vin=min. to max. Vout=nom. Iout=min. to max. Vin=48V. 5Vo, 12Vin 3.3Vo, 12Vin 1.8Vo, 12Vin 1Vo, 12Vin At all outputs low ESR; >0.001, <0.01 ohm 0.01 ohm -3 Vo set 3 ±0.3 ±0.5 75 60 40 25 ±0.02 200 1000 % Vo set % % mV pk-pk mV pk-pk mV pk-pk mV pk-pk % of Vnom./°C μF μF 0.41x0.40x0.24 10.4x10.2x6.1 0.07 2 copper alloy 2.54-7.62 1.9-3.81 Weight Pin Material Pin Finish Typical/Nominal 7.5 Tin Nickel Inches mm Ounces Grams μm μm ENVIRONMENTAL Operating Ambient Temperature Range ➈ Operating PCB Temperature Storage Temperature Thermal Protection/Shutdown 12 full power, all output voltages, see derating curves No derating Vin = Zero (no power) Measured in center -40 85 °C -40 -55 130 100 125 135 °C °C °C 130 Notes: ➀ ➁ ➂ Specifications are typical at +25 deg.C, Vin=nominal (+12V.), Vout=nominal (+5V), full load, external caps and natural convection unless otherwise indicated. Extended tests at higher power must supply substantial forced airflow. All models are tested and specified with external 1 μF paralleled with 10 μF ceramic output capacitors and a 22 μF external input capacitor. All capacitors are low ESR types. These capacitors are necessary to accommodate our test equipment and may not be required to achieve specified performance in your applications. However, Murata Power Solutions recommends installation of these capacitors. All models are stable and regulate within spec under no-load conditions. Input Back Ripple Current is tested and specified over a 5 Hz to 20 MHz bandwidth. Input filtering is Cin=2 x 100 μF tantalum, Cbus=1000 μF electrolytic, Lbus=1 μH. Note that Maximum Power Derating curves indicate an average current at nominal input voltage. At higher temperatures and/or lower airflow, the DC/DC converter will tolerate brief full current outputs if the total RMS current over time does not exceed the Derating curve. ➃ Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3, ISSUE 2, ground fixed controlled conditions, Tambient=+25 deg.C, full output load, natural air convection. ➄ The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced to -Input Common. A logic gate may also be used by applying appropriate external voltages which not exceed +Vin. ➅ Short circuit shutdown begins when the output voltage degrades approximately 1% from the selected setting. ➆ “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output. If the overcurrent condition still exists, the restart current will be removed and then tried again. This short current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter immediately recovers normal operation. ➇ Output noise may be further reduced by adding an external filter. At zero output current, the output may contain low frequency components which exceed the ripple specification. The output may be operated indefinitely with no load. ➈ All models are fully operational and meet published specifications, including “cold start” at –40°C. ➉ Regulation specifications describe the deviation as the line input voltage or output load current is varied from a nominal midpoint value to either extreme. 11 Other input or output voltage ranges will be reviewed under scheduled quantity special order. 12 Maximum PC board temperature is measured with the sensor in the center of the converter. 13 Do not exceed maximum power specifications when adjusting the output trim. 14 The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please refer to the Output Capacitive Load Application Note. 15 Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times. Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will attempt to recover when the input is brought back into normal operating range. 16 The outputs are not intended to sink appreciable reverse current. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 4 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C PERFORMANCE DATA Efficiency vs. Line Voltage and Load Current @ 25°C (Vin = 1V) Efficiency vs. Line Voltage and Load Current @ 25°C (Vin = 2.5V) 90 100 80 90 80 70 50 Efficiency (%) Efficiency (%) 70 VIN = 14V VIN = 12V VIN = 4.5V 60 40 30 VIN = 14V VIN = 12V VIN = 4.5V 60 50 40 30 20 20 10 10 0 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 1.6 0.2 0.4 Load Current (Amps) Efficiency vs. Line Voltage and Load Current @ 25°C (Vin = 3.3V) 90 90 80 80 1.2 1.4 1.6 VIN = 14V VIN = 12V VIN = 7V 70 VIN = 14V VIN = 12V VIN = 5.5V Efficiency (%) Efficiency (%) 1 Efficiency vs. Line Voltage and Load Current @ 25°C (Vin = 5V) 100 60 0.8 Load Current (Amps) 100 70 0.6 50 40 60 50 40 30 30 20 20 10 10 0 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 Load Current (Amps) Load Current (Amps) OKR-T/1.5-W12-C OSCILLOGRAMS Maximum Current Temperature Derating @ Sea Level (VIN = 7V and 12V, VOUT = 5V and 6 V) On/Off Enable Startup (Vin=12V, Vout=1.5V, Iout=1.5A, Cload=0) Channel 2=Enable, Channel 1=Vout 4.0 3.5 Output Current (Amps) 3.0 2.5 2.0 1.5 Natural convection 1.0 0.5 0.0 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 Ambient Temperature (ºC) There is no derating for Vout = 0.591V. to 5.5V. at full load. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 5 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 1.8V Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 6 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 1.8V Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=10x10μF X5R 0805 ceramic, plus Step Load Transient Response (Vin=4.5V, Vout=1.8V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 7 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 3.3V Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 8 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 3.3V Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=10x10μF X5R 0805 ceramic, plus Step Load Transient Response (Vin=5.5V, Vout=3.3V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=10x10μF 5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 9 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 5V Step Load Transient Response (Vin=12V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=5x10μF X5R 0805 ceramic, total 50μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 10 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters OKR-T/1.5-W12-C OSCILLOGRAMS – Vout = 5V Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=12x10μF X5R 0805 ceramic, total 120μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=7.5V, Vout=5V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=0A to 1.5A) Top trace=Vout, Bottom trace=Iout Step Load Transient Response (Vin=12V, Vout=5V, Cload=10x10μF X5R 0805 ceramic, plus 1x470μF, 7mΩ POSCAP, total 570μF, Iout=1.5A to 0A) Top trace=Vout, Bottom trace=Iout www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 11 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters MECHANICAL SPECIFICATIONS 0.24 (6.1) REF 0.41 (10.4) 0.205 (5.2) REF 0.11 (2.79) CL 0.05 (1.3) REF THK 0.40 (10.16) Pin #1 0.15 (3.8) Pin #5 0.067 (1.7) 0.14 (3.56) 0.134 (3.4) 0.067 (1.7) 0.032 ±.002 TYP (0.813) 0.134 (3.4) Pin #1 Dimensions are in inches (mm shown for ref. only). Third Angle Projection Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± 2˚ Components are shown for reference only. 0.42 (10.67) 5X 0.21 (5.33) 0.150 (3.81) 0.047±.005 (1.19) .26 MIN INPUT/OUTPUT CONNECTIONS OKR-T/1.5-W12-C Pin 1 2 3 4 5 1 2 3 4 5 RECOMMENDED FOOTPRINT (VIEWED FROM TOP) Figure 3. OKR-T/1.5-W12-C Component locations are typical. Function Remote On/Off Control* +VIN Ground (Common) +VOUT Trim * The Remote On/Off can be provided with either positive (P suffix) or negative (N suffix) logic. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 12 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters STANDARD PACKAGING Each static dissipative polyethylene foam tray accommodates 120 converters 2.5±.25 (63.5) Closed height 10.00 ±.25 (254.0) 10.00±.25 (254.0) Carton accommodates four (3) trays of 120 yielding 360 converters per carton. 0.49 (12.5) 9.92 (252.0) 6.5 X 45° x4 0.63 (16.0) 0.39 (10.0) 0.94 (24.0) 9.92 (252.0) 0.2 (5.0) 0.33 (8.5) 0.43 (11.0) 0.2 (5.0) Dimensions are in inches (mm shown for ref. only). Third Angle Projection Notes: 1. Material: Dow 220 antistat ethafoam (Density: 34-35 kg/m3) 2. Dimensions: 252 x 252 x 16 mm 8 x 15 array (120 per tray) Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± 2˚ Components are shown for reference only. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 13 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters TECHNICAL NOTES Input Fusing Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. For greatest safely, we recommend a fast blow fuse installed in the ungrounded input supply line. The installer must observe all relevant safety standards and regulations. For safety agency approvals, install the converter in compliance with the end-user safety standard, i.e. IEC/EN/UL 60950-1. Input Under-Voltage Shutdown and Start-Up Threshold Under normal start-up conditions, converters will not begin to regulate properly until the ramping-up input voltage exceeds and remains at the Start-Up Threshold Voltage (see Specifications). Once operating, converters will not turn off until the input voltage drops below the Under-Voltage Shutdown Limit. Subsequent restart will not occur until the input voltage rises again above the Start-Up Threshold. This built-in hysteresis prevents any unstable on/off operation at a single input voltage. Users should be aware however of input sources near the Under-Voltage Shutdown whose voltage decays as input current is consumed (such as capacitor inputs), the converter shuts off and then restarts as the external capacitor recharges. Such situations could oscillate. To prevent this, make sure the operating input voltage is well above the UV Shutdown voltage AT ALL TIMES. suggested capacitor values are 10 to 22 μF, rated at twice the expected maximum input voltage. Make sure that the input terminals do not go below the undervoltage shutdown voltage at all times. More input bulk capacitance may be added in parallel (either electrolytic or tantalum) if needed. Recommended Output Filtering The minimum external output capacitance required for proper operation is 50uF ceramic type. The maximum external output capacitance is 100uF ceramic and 470uF POSCAP. Operating outside of these minimum and maximum limits may affect the performance of the unit. Input Ripple Current and Output Noise All models in this converter series are tested and specified for input reflected ripple current and output noise using designated external input/output components, circuits and layout as shown in the figures below. In the figure below, the Cbus and Lbus components simulate a typical DC voltage bus. Please note that the values of Cin, Lbus and Cbus will vary according to the specific converter model. TO OSCILLOSCOPE CURRENT PROBE +VIN VIN LBUS + – + – CBUS CIN -VIN Start-Up Time Assuming that the output current is set at the rated maximum, the Vin to Vout Start-Up Time (see Specifications) is the time interval between the point when the ramping input voltage crosses the Start-Up Threshold and the fully loaded regulated output voltage enters and remains within its specified accuracy band. Actual measured times will vary with input source impedance, external input capacitance, input voltage slew rate and final value of the input voltage as it appears at the converter. CIN = 2 x 100μF, ESR < 700mΩ @ 100kHz CBUS = 1000μF, ESR < 100mΩ @ 100kHz LBUS = 1μH Figure 4. Measuring Input Ripple Current These converters include a soft start circuit to moderate the duty cycle of its PWM controller at power up, thereby limiting the input inrush current. +VOUT The On/Off Remote Control interval from On command to Vout regulated assumes that the converter already has its input voltage stabilized above the Start-Up Threshold before the On command. The interval is measured from the On command until the output enters and remains within its specified accuracy band. The specification assumes that the output is fully loaded at maximum rated current. Similar conditions apply to the On to Vout regulated specification such as external load capacitance and soft start circuitry. Recommended Input Filtering The user must assure that the input source has low AC impedance to provide dynamic stability and that the input supply has little or no inductive content, including long distributed wiring to a remote power supply. The converter will operate with no additional external capacitance if these conditions are met. C1 C2 SCOPE RLOAD -VOUT C1 = 1μF C2 = 10μF LOAD 2-3 INCHES (51-76mm) FROM MODULE Figure 5. Measuring Output Ripple and Noise (PARD) For best performance, we recommend installing a low-ESR capacitor immediately adjacent to the converter’s input terminals. The capacitor should be a ceramic type such as the Murata GRM32 series or a polymer type. Initial www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 14 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters Minimum Output Loading Requirements All models regulate within specification and are stable under no load to full load conditions. Operation under no load might however slightly increase output ripple and noise. CAUTION: If you routinely or accidentally exceed these Derating guidelines, the converter may have an unplanned Over Temperature shut down. Also, these graphs are all collected at slightly above Sea Level altitude. Be sure to reduce the derating for higher density altitude. Thermal Shutdown To prevent many over temperature problems and damage, these converters include thermal shutdown circuitry. If environmental conditions cause the temperature of the DC/DC’s to rise above the Operating Temperature Range up to the shutdown temperature, an on-board electronic temperature sensor will power down the unit. When the temperature decreases below the turn-on threshold, the converter will automatically restart. There is a small amount of hysteresis to prevent rapid on/off cycling. The temperature sensor is typically located adjacent to the switching controller, approximately in the center of the unit. See the Performance and Functional Specifications. Output Current Limiting Current limiting inception is defined as the point at which full power falls below the rated tolerance. See the Performance/Functional Specifications. Note particularly that the output current may briefly rise above its rated value in normal operation as long as the average output power is not exceeded. This enhances reliability and continued operation of your application. If the output current is too high, the converter will enter the short circuit condition. CAUTION: If you operate too close to the thermal limits, the converter may shut down suddenly without warning. Be sure to thoroughly test your application to avoid unplanned thermal shutdown. Temperature Derating Curves The graphs in this data sheet illustrate typical operation under a variety of conditions. The Derating curves show the maximum continuous ambient air temperature and decreasing maximum output current which is acceptable under increasing forced airflow measured in Linear Feet per Minute (“LFM”). Note that these are AVERAGE measurements. The converter will accept brief increases in current or reduced airflow as long as the average is not exceeded. Note that the temperatures are of the ambient airflow, not the converter itself which is obviously running at higher temperature than the outside air. Also note that very low flow rates (below about 25 LFM) are similar to “natural convection,” that is, not using fan-forced airflow. Output Short Circuit Condition When a converter is in current-limit mode, the output voltage will drop as the output current demand increases. If the output voltage drops too low (approximately 98% of nominal output voltage for most models), the magnetically coupled voltage used to develop primary side voltages will also drop, thereby shutting down the PWM controller. Following a time-out period, the PWM will restart, causing the output voltage to begin ramping up to its appropriate value. If the short-circuit condition persists, another shutdown cycle will initiate. This rapid on/off cycling is called “hiccup mode”. The hiccup cycling reduces the average output current, thereby preventing excessive internal temperatures and/or component damage. A short circuit can be tolerated indefinitely. The “hiccup” system differs from older latching short circuit systems because you do not have to power down the converter to make it restart. The system will automatically restore operation as soon as the short circuit condition is removed. Murata Power Solutions makes Characterization measurements in a closed cycle wind tunnel with calibrated airflow. We use both thermocouples and an infrared camera system to observe thermal performance. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 15 of 16 OKR-T/1.5-W12-C Adjustable Output 1.5-Amp SIP-mount DC/DC Converters Trim Connections Output Voltage Adustment The output voltage may be adjusted over a limited range by connecting an external trim resistor (Rtrim) between the Trim pin and Ground. The Rtrim resistor must be a 1/10 Watt precision metal film type, ±0.5% accuracy or better with low temperature coefficient, ±100 ppm/oC. or better. Mount the resistor close to the converter with very short leads or use a surface mount trim resistor. In the tables below, the calculated resistance is given. Do not exceed the specified limits of the output voltage or the converter’s maximum power rating when applying these resistors. Also, avoid high noise at the Trim input. However, to prevent instability, you should never connect any capacitors to Trim. +VOUT RTRIM Trim RLOAD Ground RTRIM (kΩ) = 1.182 VOUT − 0.591 OKR-T/1.5-W12-C Resistor Trim Equation, OKR-T/1.5-W12-C models: Output Voltage Calculated Rtrim (Ω) 6 V. 218.5 5 V. 268 3.3 V. 436 2.5 V. 619 1.8 V. 978 1.5 V. 1300 1.2 V. 1940 1.0 V. 2890 0.591 V. ∞ (open) 1.182 RTRIM (k) = _____________ (VOUT – 0.591) Soldering Guidelines Murata Power Solutions recommends the specifications below when installing these converters. These specifications vary depending on the solder type. Exceeding these specifications may cause damage to the product. Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers. Wave Solder Operations for through-hole mounted products (THMT) For Sn/Ag/Cu based solders: Maximum Preheat Temperature For Sn/Pb based solders: 115° C. Maximum Preheat Temperature 105° C. Maximum Pot Temperature 270° C. Maximum Pot Temperature 250° C. Maximum Solder Dwell Time 7 seconds Maximum Solder Dwell Time 6 seconds Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2014 Murata Power Solutions, Inc. www.murata-ps.com/support MDC_OKR-T/1.5-W12-C.A03 Page 16 of 16