Datasheet

Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
SMDJ Series
RoHS
Pb e3
Description
Uni-directional
Bi-directional
The SMDJ series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Features
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E230531
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Parameter
Symbol
Value
Unit
Peak Pulse Power Dissipation at
TA=25ºC by 10/1000µs Waveform
(Fig.2)(Note 1), (Note 2), (Note 5)
PPPM
3000
W
Power Dissipation on Infinite Heat
Sink at TL=50OC
PD
6.5
W
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave (Note 3)
IFSM
300
A
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional
Only(Note 4)
VF
3.5/5.0
V
Operating Temperature Range
TJ
-65 to 150
°C
Storage Temperature Range
TSTG
-65 to 175
°C
Typical Thermal Resistance Junction
to Lead
RθJL
15
°C/W
Typical Thermal Resistance Junction
to Ambient
RθJA
75
°C/W
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3.
2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
device only, duty cycle=4 per minute maximum.
4.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts.
5. The PPPM of stacked-die parts is 4000W and please contact littelfuse for the detail
stacked-die parts.
Functional Diagram
• 3000W peak pulse power
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
• For surface mounted
applications in order to
optimize board space
• Low profile package
• Typical failure mode is
short from over-specified
voltage or current
• Whisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
• IEC-61000-4-2 ESD
30kV(Air), 30kV (Contact)
• ESD protection of data
lines in accordance with
IEC 61000-4-2
• EFT protection of data
lines in accordance with
IEC 61000-4-4
• Built-in strain relief
• Glass passivated chip
junction
• Fast response time:
typically less than 1.0ps
from 0V to BV min
• Excellent clamping
capability
• Low incremental surge
resistance
• Typical IR less than 2μA
when VBR min>12V
• High temperature
to reflow soldering
guaranteed: 260°C/40sec
• VBR @ TJ= VBR@25°C
x (1+αT x (TJ - 25))
(αT:Temperature
Coefficient, typical value
is 0.1%)
• Plastic package is
flammability rated V-0 per
Underwriters Laboratories
•M
eet MSL level1, per
J-STD-020, LF maximun
peak of 260°C
• Matte tin lead–free plated
• Halogen free and RoHS
compliant
• Pb-free E3 means 2nd
level interconnect is
Pb-free and the terminal
finish material is tin(Sn)
(IPC/JEDEC J-STD609A.01)
Applications
TVS devices are ideal for the protection of I/O Interfaces,
VCC bus and other vulnerable circuits used in Telecom,
Computer, Industrial and Consumer electronic
applications.
Additional Infomarion
Bi-directional
Cathode
Datasheet
Resources
Samples
Anode
Uni-directional
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
Electrical Characteristics (T =25°C unless otherwise noted)
A
Part
Number
(Uni)
Part
Number
(Bi)
SMDJ5.0A
SMDJ6.0A
SMDJ6.5A
SMDJ7.0A
SMDJ7.5A
SMDJ8.0A
SMDJ8.5A
SMDJ9.0A
SMDJ10A
SMDJ11A
SMDJ12A
SMDJ13A
SMDJ14A
SMDJ15A
SMDJ16A
SMDJ17A
SMDJ18A
SMDJ20A
SMDJ22A
SMDJ24A
SMDJ26A
SMDJ28A
SMDJ30A
SMDJ33A
SMDJ36A
SMDJ40A
SMDJ43A
SMDJ45A
SMDJ48A
SMDJ51A
SMDJ54A
SMDJ58A
SMDJ60A
SMDJ64A
SMDJ70A
SMDJ75A
SMDJ78A
SMDJ85A
SMDJ90A
SMDJ100A
SMDJ110A
SMDJ120A
SMDJ130A
SMDJ150A
SMDJ160A
SMDJ170A
SMDJ180A
SMDJ220A
SMDJ5.0CA
SMDJ6.0CA
SMDJ6.5CA
SMDJ7.0CA
SMDJ7.5CA
SMDJ8.0CA
SMDJ8.5CA
SMDJ9.0CA
SMDJ10CA
SMDJ11CA
SMDJ12CA
SMDJ13CA
SMDJ14CA
SMDJ15CA
SMDJ16CA
SMDJ17CA
SMDJ18CA
SMDJ20CA
SMDJ22CA
SMDJ24CA
SMDJ26CA
SMDJ28CA
SMDJ30CA
SMDJ33CA
SMDJ36CA
SMDJ40CA
SMDJ43CA
SMDJ45CA
SMDJ48CA
SMDJ51CA
SMDJ54CA
SMDJ58CA
SMDJ60CA
SMDJ64CA
SMDJ70CA
SMDJ75CA
SMDJ78CA
SMDJ85CA
SMDJ90CA
SMDJ100CA
SMDJ110CA
SMDJ120CA
SMDJ130CA
SMDJ150CA
SMDJ160CA
SMDJ170CA
SMDJ180CA
SMDJ220CA
UNI
BI
Reverse
Stand off
Voltage
VR
(Volts)
RDE
RDG
RDK
PDM
PDP
PDR
PDT
PDV
PDX
PDZ
PEE
PEG
PEK
PEM
PEP
PER
PET
PEV
PEX
PEZ
PFE
PFG
PFK
PFM
PFP
PFR
PFT
PFV
PFX
PFZ
RGE
PGG
PGK
PGM
PGP
PGR
PGT
PGV
PGX
PGZ
PHE
PHG
PHK
PHM
PHP
PHR
PHT
PKE
DDE
DDG
DDK
DDM
DDP
DDR
DDT
DDV
DDX
DDZ
DEE
DEG
DEK
DEM
DEP
DER
DET
DEV
DEX
DEZ
DFE
DFG
DFK
DFM
DFP
DFR
DFT
DFV
DFX
DFZ
DGE
DGG
DGK
DGM
DGP
DGR
DGT
DGV
DGX
DGZ
DHE
DHG
DHK
DHM
DHP
DHR
DHT
DKE
5.0
6.0
6.5
7.0
7.5
8.0
8.5
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
33.0
36.0
40.0
43.0
45.0
48.0
51.0
54.0
58.0
60.0
64.0
70.0
75.0
78.0
85.0
90.0
100.0
110.0
120.0
130.0
150.0
160.0
170.0
180.0
220.0
Marking
For bidirectional type having VR of 10 volts and less, the IR limit is double.
For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Breakdown
Voltage VBR
(Volts) @ IT
MIN
MAX
Test
Current
IT
(mA)
6.40
6.67
7.22
7.78
8.33
8.89
9.44
10.00
11.10
12.20
13.30
14.40
15.60
16.70
17.80
18.90
20.00
22.20
24.40
26.70
28.90
31.10
33.30
36.70
40.00
44.40
47.80
50.00
53.30
56.70
60.00
64.40
66.70
71.10
77.80
83.30
86.70
94.40
100.00
111.00
122.00
133.00
144.00
167.00
178.00
189.00
200.00
244.00
7.00
7.37
7.98
8.60
9.21
9.83
10.40
11.10
12.30
13.50
14.70
15.90
17.20
18.50
19.70
20.90
22.10
24.50
26.90
29.50
31.90
34.40
36.80
40.60
44.20
49.10
52.80
55.30
58.90
62.70
66.30
71.20
73.70
78.60
86.00
92.10
95.80
104.00
111.00
123.00
135.00
147.00
159.00
185.00
197.00
209.00
221.00
270.00
10
10
10
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Maximum Maximum Maximum
Agency
Clamping
Peak
Reverse
Approval
Voltage VC
Pulse
Leakage IR
@ Ipp
Current Ipp
@ VR
(V)
(A)
(µA)
9.2
10.3
11.2
12.0
12.9
13.6
14.4
15.4
17.0
18.2
19.9
21.5
23.2
24.4
26.0
27.6
29.2
32.4
35.5
38.9
42.1
45.4
48.4
53.3
58.1
64.5
69.4
72.7
77.4
82.4
87.1
93.6
96.8
103.0
113.0
121.0
126.0
137.0
146.0
162.0
177.0
193.0
209.0
243.0
259.0
275.0
292.0
356.0
326.1
291.3
267.9
250.0
232.6
220.6
208.3
194.8
176.5
164.8
150.8
139.5
129.3
123.0
115.4
108.7
102.7
92.6
84.5
77.1
71.3
66.1
62.0
56.3
51.6
46.5
43.2
41.3
38.8
36.4
34.4
32.1
31.0
29.1
26.5
24.8
23.8
21.9
20.5
18.5
16.9
15.5
14.4
12.3
11.6
10.9
10.3
8.4
800
800
500
200
100
50
20
10
5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
I-V Curve Characteristics
Bi-directional
Uni-directional
Ipp
IT
IR
Vc VBR VR
Vc VBR VR
IR
IT
V
IR VF
IT
VR VBR Vc
V
Ipp
Ipp
PPPM
VR
VBR
VC
IR
VF
Peak Pulse Power Dissipation -- Max power dissipation
Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)
Reverse Leakage Current -- Current measured at VR
Forward Voltage Drop for Uni-directional
Ratings and Characteristic Curves (T =25°C unless otherwise noted)
A
Figure 1 - TVS Transients Clamping Waveform
Figure 2 - Peak Pulse Power Rating
Voltage Transients
PPPM-Peak Pulse Power (kW)
100
Voltage or Current
Voltage Across TVS
stacked-die, 4kW
at 10x1000µs, 25°C
10
Current Through TVS
Single die, 3kW
at 10x1000µs, 25°C
1
TJ initial = Tamb
0.1
0.001
Time
0.01
0.1
1
10
td-Pulse Width (ms)
continues on next page.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued)
A
Figure 3 - Peak Pulse Power Derating Curve
Figure 4 - Pulse Waveform
150
IPPM- Peak Pulse Current, % IRSM
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage %
100
80
60
40
20
0
0
25
50
75
100 125 150
TJ - Initial Junction Temperature (ºC)
2
Uni-direconal V=VR
Bi-direconal V=VR
10
100
td
1.0
0
3.0
4.0
10
1
0.1
0.01
0.001
1000
0.01
0.1
VBR - Reverse Breakdown Voltage(V)
1
10
100
1000
TP - Pulse Duration (s)
Figure 7 - Maximum Non-Repetitive Peak Forward
500 Surge Current Uni-Directional Only
Figure 8 - Peak Forward Voltage Drop vs Peak Forward
Current (Typical Values)
100
450
IF- Peak Forward Current(A)
IFSM - Peak Forward Surve Current (A)
2.0
100
1
10
10/1000µsec. Waveform
as defined by R.E.A
t-Time (ms)
Transient Thermal Impedance (°C/W)
Cj(pF)
Bi-direconal V=0V
1
( )
50
Figure 6 - Typical Transient Thermal Impedance
Uni-direconal V=0V
100
Half Value
IPPM IPPM
175
100000
10000
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
Peak Value
IPPM
100
0
Figure 5 - Typical Junction Capacitance
1000
tr=10µsec
400
350
300
250
200
150
100
Single die
10
Stack-die
1
0.1
50
0.01
0
1
10
Number of Cycles at 60 Hz
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
100
0.00
1.00
2.00
3.00
4.00
5.00
6.00
VF-Peak Forward Voltage(V)
7.00
8.00
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
Soldering Parameters
Lead–free
assembly
Pre Heat
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus Temp (TA)
to peak
3°C/second max
TS(max) to TA - Ramp-up Rate
3°C/second max
Reflow
- Temperature (TA) (Liquidus)
217°C
- Time (min to max) (ts)
60 – 150 seconds
Peak Temperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
260°C
Physical Specifications
tp
TP
Ramp-up
TL
Temperature (T)
Reflow Condition
tL
Critical Zone
TL to TP
Ts(max)
Ramp-down
Ts(min)
ts
Preheat
25˚C
t 25˚C to Peak
Time (t)
Environmental Specifications
High Temp. Storage
JESD22-A103
HTRB
JESD22-A108
Weight
0.007 ounce, 0.21 grams
Temperature Cycling
JESD22-A104
Case
JEDEC DO214AB. Molded plastic body
over glass passivated junction
MSL
JEDEC-J-STD-020, Level 1
Polarity
Color band denotes positive end
(cathode) except Bidirectional.
H3TRB
JESD22-A101
Terminal
Matte Tin-plated leads, Solderable per
JESD22-B102
RSH
JESD22-A111
Dimensions
DO-214AB (SMC J-Bend)
Cathode Band
(for Uni-directional products only)
C
A
B
H
D
F
E
G
J
K
L
I
Dimensions
Inches
Min
Millimeters
Max
Min
Max
A
0.114
0.126
2.900
3.200
B
0.260
0.280
6.600
7.110
C
0.220
0.245
5.590
6.220
D
0.079
0.103
2.060
2.620
E
0.030
0.060
0.760
1.520
F
-
0.008
-
0.203
G
0.305
0.320
7.750
8.130
H
0.006
0.012
0.152
0.305
I
0.129
-
3.300
-
J
0.094
-
2.400
-
K
-
0.165
L
0.094
-
4.200
2.400
-
Solder Pads
(all dimensions in mm)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
Part Numbering System
Part Marking System
SMDJ XXX C A
Cathode Band
F
(for Uni-directional products only)
5% VBR VOLTAGE TOLERANCE
BI-DIRECTIONAL
XXX
VR VOLTAGE
YMXXX
SERIES
Littelfuse Logo
Marking Code
Trace Code Marking
Y:Year Code
M: Month Code
XXX: Lot Code
Packaging Options
Part number
Component
Package
SMDJxxxXX
DO-214AB
3000
Tape & Reel - 16mm tape/13” reel
EIA STD RS-481
SMDJxxxXX-T7
DO-214AB
500
Tape & Reel – 16mm tape/7” reel
EIA STD RS-481
Packaging
Option
Quantity
Packaging
Specification
Tape and Reel Specification
0.157
(4.0)
0.63
(16.0)
Cathode
0.315
(8.0)
Optional
7” 7.0 (187)
13” 13.0 (330)
0.80 (20.2)
Arbor Hole Dia.
0.65
(16.4)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
0.059 DIA
(1.5)
Cover tape
Dimensions are in inches
(and millimeters).
Direction of Feed