PEH534

Snap-In Aluminum Electrolytic Capacitors
PEH534 Series, +105ºC
Overview
Applications
KEMET's PEH534 is a long-life electrolytic capacitor designed
to offer high ripple current capability and low mounting cost. Low
ESR is the result of a very low resistive paper/electrolyte system.
Low ESR, together with the TDC thermal concept, gives the
PEH534 a high ripple current capability.
Typical applications for KEMET's PEH534 capacitor include
switch mode power supplies (SMPS), drives, welding equipment,
uninterruptible power supplies (UPS), and other power electronic
applications where high current ratings and compact size are
important.
Benefits
•Snap-In
• 3,000 hours at +105°C (VR, IR applied)
• PCB mounting
• Low ESR and ESL
• High ripple current
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Part Number System
PEH534
J
BC
456
0
M
2
Series
Voltage (VDC)
Size Code
Capacitance Code (µF)
Version
Capacitance Tolerance
Termination
See Dimension
Table
The second two digits
indicate the two most
significant digits of the
capacitance value. The
first digit indicates the
total number digits.
0 = Standard
M = ±20%
See Termination
Table
Snap-In type
Aluminum
Electrolytic
J = 35
M = 63
P = 100
R = 200
S = 250
U = 350
V = 400
Y = 450
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
1
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Performance Characteristics
Item
Performance Characteristics
Capacitance Range
150 – 22,000 µF
Rated Voltage
35 – 450 VDC
Operating Temperature
-40 to +105°C
Capacitance Tolerance
±20% at 100 Hz / +20°C
Operational Lifetime
Shelf Life
Rated Voltage and Ripple Current at
+105°C (hours)
Rated Voltage at +105°C (hours)
22 – 40
3,000
4,000
4 years at +40°C 0 VDC
I = 0.003 CV (µA)
Leakage Current
Vibration Test Specifications
D (mm)
C = rated capacitance (µF), V = rated voltage (VDC). Voltage applied for 5 minutes at +20°C.
Procedure
Requirements
0.75 mm displacement amplitude or
10 g maximum acceleration. Vibration
applied for three 2-hour sessions at
10 – 500 Hz (Capacitor clamped by
body).
No leakage of electrolyte or other visible damage. Deviations in capacitance
and tanδ from initial measurements must not exceed: ∆ C/C < 5%
Standards
IEC 60384-4 long life grade 40/105/56, in accordance with CECC 30 301–809
Test Method & Performance
Endurance Life Test
Conditions
Performance
Temperature
+105°C
Test Duration
2,000 hours
Ripple Current
Voltage
Performance
Capacitance Change
Equivalent Series Resistance
Leakage Current
Maximum ripple current specified in table
The sum of DC voltage and the peak AC voltage must not exceed the rated voltage of the capacitor
The following specifications will be satisfied when the capacitor is tested at +20°C:
≤ 160 V
Within 15% of the initial value
> 160 V
Within 10% of the initial value
Does not exceed 200% of the initial value
Does not exceed leakage current limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
2
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Dimensions – Millimeters
DXL
Size Code
Dimensions in mm
D1
L1
±0.5
±1.0
Approximate
Weight
Grams
25 x 30
25 x 35
25 x 40
25 x 45
25 x 50
30 x 25
30 x 30
30 x 35
30 x 40
BC
BD
BE
BF
BG
CB
CC
CD
CE
25.5
25.5
25.5
25.5
25.5
30.5
30.5
30.5
30.5
31
36
41
46
51
26
31
36
41
21
24
27
30
33
24
29
34
39
30 x 45
30 x 50
35 x 25
35 x 30
35 x 35
35 x 40
35 x 45
35 x 50
CF
CG
DB
DC
DD
DE
DF
DG
30.5
30.5
35.5
35.5
35.5
35.5
35.5
35.5
46
51
26
31
36
41
46
51
45
51
32
40
48
56
64
72
Note: Add 0.5 mm to D and 1 mm to L for Sleeving
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
3
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Termination Tables
Termination Code
2
2S
3
25
•
•
•
30
•
•
•
35
•
•
•
Diameter (mm)
4
4S
•
•
Mounting: These capacitors are designed to be mounted by their terminations alone and may be used in any position.
Dummy pins on 4-pin decks must be isolated.
Termination
Code
LL
Termination
Style
±1
Standard Termination Option
2
2 Pin
6.3
Other Termination Options
2S
2 Pin
4
3
3 Pin
4
4
4 Pin
6.3
4S
4 Pin
4
Dimensions in mm
Style 2/2S
SIDE VIEW
L
PCB LAYOUT
TERMINAL
END VIEW
D
2 ±0.1
LL
Style 3
SIDE VIEW
L
D
L
3.3 ±0.1
Ø2.5 Minimum
+ ve
4.75 ±0.1
10 ±0.1
Ø2 ±0.1 Typical
-
+
SIDE VIEW
PCB LAYOUT
TERMINAL
END VIEW
5.8 ±1
Style 4/4S
10 ±0.1
TERMINAL
END VIEW
PCB LAYOUT
4 Holes Ø2 ±0.1
on a Ø22.5 PCD
- ve
-
D
+
5.8 ±1
30°
30°
+ ve
\
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
4
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Shelf Life
The capacitance, ESR and impedance of a capacitor will not change significantly after extended storage periods, however the leakage
current will very slowly increase. KEMET products are particularly stable and allow a shelf life in excess of three years at 40°C. See
sectional specification under each product series for specific data.
Re-age (Reforming) Procedure
Apply the rated voltage to the capacitor at room temperature for a period of one hour, or until the leakage current has fallen to a steady
value below the specified limit. During re-aging a maximum charging current of twice the specified leakage current or 5 mA (whichever
is greater) is suggested.
Reliability
The reliability of a component can be defined as the probability that it will perform satisfactorily under a given set of conditions for a
given length of time.
In practice, it is impossible to predict with absolute certainty how any individual component will perform; thus, we must utilize probability
theory. It is also necessary to clearly define the level of stress involved (e.g. operating voltage, ripple current, temperature and time).
Finally, the meaning of satisfactory performance must be defined by specifying a set of conditions which determine the end of life of the
component.
Reliability as a function of time, R(t), is normally expressed as: R(t)=e-λt
where R(t) is the probability that the component will perform satisfactorily for time t, and λ is the failure rate.
Failure Rate
The failure rate is the number of components failing per unit time. The failure rate of most electronic components follows the
characteristic pattern:
• Early failures are removed during the manufacturing process.
• The operational life is characterized by a constant failure rate.
• The wear out period is characterized by a rapidly increasing failure rate.
The failures in time (FIT) are given with a 60% confidence level for the various type codes. By convention, FIT is expressed as 1 x 10-9
failures per hour. Failure rate is also expressed as a percentage of failures per 1,000 hours.
e.g., 100 FIT = 1 x 10-7 failures per hour = 0.01%/1,000 hours
End of Life Definition
Catastrophic Failure: short circuit, open circuit or safety vent operation
Parametric Failure:
• Change in capacitance > ±10%
• Leakage current > specified limit
• ESR > 2 x initial ESR value
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
5
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
MTBF
The mean time between failures (MTBF) is simply the inverse of the failure rate.
MTBF= 1/λ
Failure Rate
early failures
wear out
operational life
Time
The failure rate is derived from our periodic test results. The failure rate (λR) is, therefore, only given at test temperature for life tests. An
estimation is also given at 40°C. The expected failure rate for this capacitor range is based on our periodic test results for capacitors
with structural similarity. Failure rate is frequently quoted in FIT (Failures In Time) where 1 FIT = 1 x 10-9 failures per hour. Failure rate
per hour includes both catastrophic and parametric failures.
Environmental Compliance
As an environmentally conscious company, KEMET is working continuously with improvements concerning the environmental effects
of both our capacitors and their production. In Europe (RoHS Directive) and in some other geographical areas like China, legislation
has been put in place to prevent the use of some hazardous materials, such as lead (Pb), in electronic equipment. All products in this
catalog are produced to help our customers’ obligations to guarantee their products and fulfill these legislative requirements. The only
material of concern in our products has been lead (Pb), which has been removed from all designs to fulfill the requirement of containing
less than 0.1% of lead in any homogeneous material. KEMET will closely follow any changes in legislation world wide and makes any
necessary changes in its products, whenever needed.
Some customer segments such as medical, military and automotive electronics may still require the use of lead in electrode coatings.
To clarify the situation and distinguish products from each other, a special symbol is used on the packaging labels for RoHS compatible
capacitors.
Because of customer requirements, there may appear additional markings such as LF = Lead Free or LFW = Lead Free Wires on the
label.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
6
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Table 1 – Ratings & Part Number Reference
VDC
Rated
Capacitance
35
35
35
35
35
35
35
35
35
35
35
63
63
63
63
63
63
63
63
63
63
63
100
100
100
100
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
250
250
250
250
250
250
250
250
250
250
250
250
350
350
350
350
350
350
350
100 Hz
20°C (µF)
5600
6800
6800
8200
8200
8200
10000
10000
15000
15000
22000
2200
3300
3300
4700
4700
5600
5600
6800
6800
8200
10000
1500
1500
2200
2200
3300
3300
3900
4700
470
560
560
680
680
680
820
820
1000
1000
1500
390
390
470
470
470
560
560
680
680
820
820
1000
220
220
220
330
330
390
390
VDC
Rated Capacitance
Size Code
Case Size
Ripple Current Maximum
D x L (mm)
BC
BD
CB
BE
CC
DB
BF
CD
CF
DD
DG
BC
BE
CC
CE
DC
CF
DD
CG
DE
DF
DG
BE
CC
CE
DC
CG
DE
DF
DG
BD
BE
CC
BF
CD
DC
CE
DC
CG
DD
DF
BE
CC
BF
CD
DC
BG
CE
CF
DD
CG
DE
DF
BE
CC
DB
CE
DC
CF
DD
25 x 30
25 x 35
30 x 25
25 x 40
30 x 30
35 x 25
25 x 45
30 x 35
30 x 45
35 x 35
35 x 50
25 x 30
25 x 40
30 x 30
30 x 40
35 x 30
30 x 45
35 x 35
30 x 50
35 x 40
35 x 45
35 x 50
25 x 40
30 x 30
30 x 40
35 x 30
30 x 50
35 x 40
35 x 45
35 x 50
25 x 35
25 x 40
30 x 30
25 x 45
30 x 35
35 x 30
30 x 40
35 x 30
30 x 50
35 x 35
35 x 45
25 x 40
30 x 30
25 x 45
30 x 35
35 x 30
25 x 50
30 x 40
30 x 45
35 x 35
30 x 50
35 x 40
35 x 45
25 x 40
30 x 30
35 x 25
30 x 40
35 x 30
30 x 45
35 x 35
Size Code
Case Size
100 Hz
105°C (A)
2.3
2.7
2.9
3.1
3.5
3.1
3.5
4.1
5.3
4.5
6.2
1.9
2.5
2.7
3.6
3.1
4.0
3.7
4.5
4.2
4.7
5.2
1.9
2.0
2.6
2.4
3.3
3.3
3.6
4.1
1.1
1.3
1.3
1.4
1.5
1.5
1.7
1.6
2.0
1.9
2.5
1.1
1.1
1.3
1.3
1.3
1.4
1.5
1.7
1.7
1.9
1.9
2.2
0.9
0.9
0.9
1.2
1.2
1.4
1.4
20 kHz
40°C (A)
7.6
9.0
9.8
10.2
12.1
10.0
11.3
14.3
17.8
14.4
20.1
6.9
9.3
10.6
14.0
11.2
15.6
13.3
17.1
15.2
16.8
18.4
7.0
7.4
9.8
8.8
12.4
11.7
13.1
14.5
7.1
8.0
8.9
8.9
10.4
9.8
11.8
9.8
13.9
11.6
14.7
7.9
8.7
8.8
10.1
9.6
9.6
11.4
12.8
11.5
14.2
13.1
14.6
5.8
6.0
5.8
8.0
7.4
9.0
8.6
ESR Maximum
100 Hz
20°C (mΩ)
54
43
40
36
31
37
31
25
17
21
14
92
61
56
39
44
33
36
28
30
26
22
140
130
91
96
62
64
54
46
290
250
240
200
200
200
160
170
130
140
93
290
280
240
240
240
200
200
160
170
140
140
110
560
550
560
370
370
310
320
Ripple Current
100 kHz
20°C (mΩ)
43
34
31
28
23
29
24
18
13
17
11
43
34
31
28
23
29
24
18
13
17
11
110
100
70
75
48
50
43
36
160
130
130
110
100
110
87
93
71
75
51
140
140
120
110
120
100
95
79
83
66
69
57
350
340
350
230
230
190
200
ESR
Part Number
PEH534JBC4560M(1)
PEH534JBD4680M(1)
PEH534JCB4680M(1)
PEH534JBE4820M(1)
PEH534JCC4820M(1)
PEH534JDB4820M(1)
PEH534JBF5100M(1)
PEH534JCD5100M(1)
PEH534JCF5150M(1)
PEH534JDD5150M(1)
PEH534JDG5220M(1)
PEH534MBC4220M(1)
PEH534MBE4330M(1)
PEH534MCC4330M(1)
PEH534MCE4470M(1)
PEH534MDC4470M(1)
PEH534MCF4560M(1)
PEH534MDD4560M(1)
PEH534MCG4680M(1)
PEH534MDE4680M(1)
PEH534MDF4820M(1)
PEH534MDG5100M(1)
PEH534PBE4150M(1)
PEH534PCC4150M(1)
PEH534PCE4220M(1)
PEH534PDC4220M(1)
PEH534PCG4330M(1)
PEH534PDE4330M(1)
PEH534PDF4390M(1)
PEH534PDG4470M(1)
PEH534RBD3470M(1)
PEH534RBE3560M(1)
PEH534RCC3560M(1)
PEH534RBF3680M(1)
PEH534RCD3680M(1)
PEH534RDC3680M(1)
PEH534RCE3820M(1)
PEH534RDC3820M(1)
PEH534RCG4100M(1)
PEH534RDD4100M(1)
PEH534RDF4150M(1)
PEH534SBE3390M(1)
PEH534SCC3390M(1)
PEH534SBF3470M(1)
PEH534SCD3470M(1)
PEH534SDC3470M(1)
PEH534SBG3560M(1)
PEH534SCE3560M(1)
PEH534SCF3680M(1)
PEH534SDD3680M(1)
PEH534SCG3820M(1)
PEH534SDE3820M(1)
PEH534SDF4100M(1)
PEH534UBE3220M(1)
PEH534UCC3220M(1)
PEH534UDB3220M(1)
PEH534UCE3330M(1)
PEH534UDC3330M(1)
PEH534UCF3390M(1)
PEH534UDD3390M(1)
Part Number
(1) Termination code: See Termination Tables for available options.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
7
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Table 1 – Ratings & Part Number Reference cont'd
VDC
Rated
Capacitance
350
350
400
400
400
400
400
400
400
400
400
400
400
450
450
450
450
450
450
450
450
450
100 Hz
20°C (µF)
470
560
150
150
220
220
220
330
330
390
390
470
560
150
150
150
220
220
330
330
390
470
VDC
Rated Capacitance
Size Code
Case Size
Ripple Current Maximum
D x L (mm)
DE
DF
BD
CB
BF
CD
DC
CF
DD
CG
DE
DF
DG
BE
CC
DB
CE
DC
CG
DE
DF
DG
35 x 40
35 x 45
25 x 35
30 x 25
25 x 45
30 x 35
35 x 30
30 x 45
35 x 35
30 x 50
35 x 40
35 x 45
35 x 50
25 x 40
30 x 30
35 x 25
30 x 40
35 x 30
30 x 50
35 x 40
35 x 45
35 x 50
Size Code
Case Size
100 Hz
105°C (A)
1.6
1.8
0.8
0.8
1.0
1.0
1.1
1.4
1.4
1.5
1.5
1.8
2.0
0.9
0.9
0.9
1.2
1.2
1.5
1.5
1.7
1.9
20 kHz
40°C (A)
9.7
10.9
5.1
5.2
6.5
7.1
7.0
9.2
8.7
10.2
9.8
11.1
12.3
5.8
6.1
5.9
8.1
7.5
10.3
9.9
11.3
12.4
ESR Maximum
100 Hz
20°C (mΩ)
260
220
680
680
470
460
460
310
310
260
260
220
180
570
560
570
380
390
260
260
220
180
Ripple Current
100 kHz
20°C (mΩ)
160
140
410
400
280
270
280
180
190
160
160
130
110
330
330
330
220
230
150
150
130
110
ESR
Part Number
PEH534UDE3470M(1)
PEH534UDF3560M(1)
PEH534VBD3150M(1)
PEH534VCB3150M(1)
PEH534VBF3220M(1)
PEH534VCD3220M(1)
PEH534VDC3220M(1)
PEH534VCF3330M(1)
PEH534VDD3330M(1)
PEH534VCG3390M(1)
PEH534VDE3390M(1)
PEH534VDF3470M(1)
PEH534VDG3560M(1)
PEH534YBE3150M(1)
PEH534YCC3150M(1)
PEH534YDB3150M(1)
PEH534YCE3220M(1)
PEH534YDC3220M(1)
PEH534YCG3330M(1)
PEH534YDE3330M(1)
PEH534YDF3390M(1)
PEH534YDG3470M(1)
Part Number
(1) Termination code: See Termination Tables for available options.
Mechanical Data
The capacitor may be mounted in any position. PEH534 is supplied with an insulation sleeve. Voltage proof of the insulation sleeve =
2.5 kVDC (1 min). The minus pole is marked on the case surface. UL recognized sleeving is available for custom parts in this range,
upon request. (UL No. E358957)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
8
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Marking
KEMET Logo
Part Number Code
Rated Capacitance,
Rated Voltage (VDC)
Operating Temperature
Date of Manufacture,
Batch Number
Polarity Stripe (-)
(Not Shown)
Construction
Detailed Cross Section
Termination Pin
Insulating End Disc
Insulating Sleeve
Aluminum Can with
Safety Vent
Laser Welded
Terminal Tabs
Rubber Seal
Laser Welded
Terminal Tab
Margin
Aluminum Can
Insulating Sleeve
Polarity Stripe (-)
(Not Shown)
Rubber Seal
Paper Spacer Impregnated
with Electrolyte
(First Layer)
Cathode Aluminum
Foil, Etched
(Second Layer)
Paper Spacer Impregnated
with Electrolyte
(Third Layer)
Termination Pin (+)
Anode Aluminum Foil, Etched,
Covered with Aluminum Oxide
(Fourth Layer)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Termination Pin (-)
A4024_PEH534 • 8/26/2015
9
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Construction cont'd
The manufacturing process begins with the anode foil being
electrochemically etched to increase the surface area and then
“formed” to produce the aluminum oxide layer. Both the anode and
cathode foils are then interleaved with absorbent paper and wound
into a cylinder. During the winding process, aluminum tabs are
attached to each foil to provide the electrical contact.
Extended cathode
Anode foil
The deck, complete with terminals, is attached to the tabs and then
folded down to rest on top of the winding. The complete winding
is impregnated with electrolyte before being housed in a suitable
container, usually an aluminum can, and sealed. Throughout the
process, all materials inside the housing must be maintained at the
highest purity and be compatible with the electrolyte.
Each capacitor is aged and tested before being sleeved and
packed. The purpose of aging is to repair any damage in the oxide
layer and thus reduce the leakage current to a very low level. Aging
is normally carried out at the rated temperature of the capacitor and
is accomplished by applying voltage to the device while carefully
controlling the supply current. The process may take several hours
to complete.
Damage to the oxide layer can occur due to variety of reasons:
• Slitting of the anode foil after forming
• Attaching the tabs to the anode foil
• Minor mechanical damage caused during winding
A sample from each batch is taken by the quality department after
completion of the production process.
The following tests are applied and may be varied at the request
of the customer. In this case the batch, or special procedure, will
determine the course of action.
Electrical:
• Leakage current
• Capacitance
• ESR
• Impedance
• Tan Delta
Mechanical/Visual:
• Overall dimensions
• Torque test of mounting stud
• Print detail
• Box labels
• Packaging, including packed
quantity
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Foil tabs
Tissues
Cathode foil
Etching
Forming
Winding
Decking
Impregnation
Assembly
Aging
Testing
Sleeving
Packing
A4024_PEH534 • 8/26/2015
10
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Skopje, Macedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Wyboston, United Kingdom
Tel: 44-1480-273082
Taipei, Taiwan
Tel: 886-2-27528585
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
2835 KEMET Way
Simpsonville, SC 29681
Northeast
Wilmington, MA
Tel: 978-658-1663
Southeast
Lake Mary, FL
Tel: 407-855-8886
Central
Novi, MI
Tel: 248-994-1030
Beijing, China
Tel: 86-10-5877-1075
Shanghai, China
Tel: 86-21-6447-0707
Seoul, South Korea
Tel: 82-2-6294-0550
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Irving, TX
Tel: 972-915-6041
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
11
Snap-In Aluminum Electrolytic Capacitors – PEH534, +105ºC
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4024_PEH534 • 8/26/2015
12