all converter caty11419231533

MFU100 SERIES
DC/DC CONVERTER 1W
FEATURES
►Miniature DIP-Package with Industry Standard Pinout
►Package Dimension:
12.7 x 7.0 x 10.2 mm (0.50"x 0.28"x 0.40" inches)
►High I/O-Isolation 3000 VDC
►Operating Temp. Range -40°C to +85°C
►UL/cUL/IEC/EN 60950-1 Safety Approval
►3 Years Product Warranty
PRODUCT OVERVIEW
The MINMAX MFU100 series is a range of 1W DC/DC converters in a miniature DIP Package featuring I/O-isolation of 3000VDC. A high efficiency allows
an operating temperature range of –40°C to +85°C.
These converters offer an economical solution for many space critical applications where a voltage has to be isolated i.e for noise reduction, ground loop
elimination, digital interfaces or for board level power distribution.
Model Selection Guide
Model
Input
Output
Number
Voltage
Voltage
(Range)
VDC
MFU102
MFU103
MFU104
MFU105
MFU112
MFU113
MFU114
MFU115
MFU122
MFU123
MFU124
MFU125
5
(4.5 ~ 5.5)
12
(10.8 ~ 13.2)
24
(21.6 ~ 26.4)
VDC
5
9
12
15
5
9
12
15
5
9
12
15
Output Current
Input Current
Max.
Min.
@Max. Load
@No Load
mA
200
110
84
67
200
110
84
67
200
110
84
67
mA
4
2
1.5
1
4
2
1.5
1
4
2
1.5
1
mA(typ.)
290
260
262
257
117
107
106
106
60
54
53
53
mA(typ.)
Load
Max. capacitive
Regulation
Load
Efficiency
(typ.)
@Max. Load
% (max.)
11
8
7
6
9
5
5
4
8
5
4
4
30
13
10
μF
33
33
33
%
69
76
77
78
71
77
79
79
70
76
79
79
# For each output
Input Specifications
Parameter
Input Voltage Range
Input Surge Voltage (1 sec. max.)
Model
Min.
Typ.
Max.
5V Input Models
4.5
5
5.5
12V Input Models
10.8
12
13.2
24V Input Models
21.6
24
26.4
5V Input Models
-0.7
---
7
12V Input Models
-0.7
---
15
24V Input Models
-0.7
---
28
---
---
0.3
Reverse Polarity Input Current
All Models
Internal Filter Type
Internal Power Dissipation
2014/11/27 REV:7
Tel:886-6-2923150
Page 1 of 4
VDC
A
Internal Capacitor
---
E-mail:[email protected]
Unit
---
450
mW
MFU100 SERIES
DC/DC CONVERTER 1W
Output Specifications
Parameter
Conditions
Output Voltage Accuracy
Line Regulation
For Vin Change of 1%
Load Regulation
Io=20% to 100%
Ripple & Noise
0-20 MHz Bandwidth
Temperature Coefficient
Min.
Typ.
Max.
Unit
---
±1.0
±3.0
%
---
±1.2
±1.5
%
See Model Selection Guide
---
100
150
mV P-P
---
±0.01
±0.02
%/℃
Short Circuit Protection
0.5 Second Max.
General Specifications
Parameter
Conditions
Min.
Typ.
Max.
Unit
60 Seconds
3000
---
---
VDC
I/O Isolation Resistance
500 VDC
10
---
---
GΩ
I/O Isolation Capacitance
100KHz, 1V
---
60
100
pF
50
90
110
KHz
I/O Isolation Voltage
Switching Frequency
MTBF (calculated)
MIL-HDBK-217F@25℃, Ground Benign
2,000,000
Hours
Environmental Specifications
Parameter
Operating Ambient Temperature Range (See
Power Derating Curve)
Case Temperature
Storage Temperature Range
Humidity (non condensing)
Cooling
Lead Temperature (1.5mm from case for 10Sec.)
Conditions
Min.
Max.
Unit
Natural Convection
-40
+85
℃
+90
+125
95
℃
℃
% rel. H
260
℃
---50
--Free-Air convection
---
Power Derating Curve
(5V Output Only)
(All Other Output)
Notes
1
Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted.
2
These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these
3
We recommend to protect the converter by a slow blow fuse in the input supply line.
modules; however they may not meet all specifications listed.
4
Other input and output voltage may be available, please contact factory.
5
That “natural convection” is about 20LFM but is not equal to still air (0 LFM).
6
Specifications are subject to change without notice.
E-mail:[email protected]
2014/11/27 REV:7
Tel:886-6-2923150
Page 2 of 4
MFU100 SERIES
DC/DC CONVERTER 1W
Package Specifications
3.1
[0.12]
L
Pin Connections
0.4 [0.02]
Mechanical Dimensions
2.54
[0.10]
0.50
[0.02]
7.62 [0.30]
Bottom View
7
5
-Vin
4
+Vin
5
+Vout
7
-Vout
L=8.0 [0.31] for 24V Input Models
10.2 [0.40]
4
Function
1
L=7.0 [0.28] for 5V & 12V Input Models
2.6
[0.10]
7.62 [0.30]
1
Pin
12.7 [0.50]
1.29
[0.05]
►All
5.08
[0.20]
dimensions in mm (inches)
►Tolerance: X.X±0.25
►Pin
Physical Characteristics
Case Size(5V&12V Input)
:
12.7x7.0x10.2mm (0.50x0.28x0.40 inches)
Case Size(24V Input)
:
12.7x8.0x10.2mm (0.50x0.31x0.40 inches)
Case Material
:
Non-Conductive Black Plastic (flammability to UL 94V-0 rated)
Pin Material
:
phosphor bronze
Weight(5V&12V Input)
:
1.3g
Weight(24V Input)
:
1.7g
E-mail:[email protected]
2014/11/27 REV:7
Tel:886-6-2923150
Page 3 of 4
(X.XX±0.01)
X.XX±0.13 ( X.XXX±0.005)
diameter  0.5 ±0.05 (0.02±0.002)
MFU100 SERIES
DC/DC CONVERTER 1W
Test Setup
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33μF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load
between 50 mm and 75 mm from the DC/DC Converter.
+Vin
+Out
Copper Strip
Single Output
DC / DC
Converter
-Vin
Cout
-Out
Scope
Resistive
Load
Copper Strip
Technical Notes
Maximum Capacitive Load
The MFU100 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up,
affecting the ramp-up and the startup time. For optimum performance we recommend 33μF maximum capacitive load for devices. The maximum capacitance can be
found in the data sheet..
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module.
In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup.
Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR <
1.0Ω at 100 KHz) capacitor of a 1.5μF for the 5V input devices, a 1.0μF for the 12V input devices and a 0.47μF for the 24V devices.
+
DC Power
Source
+Vin
+
+Out
DC / DC
Converter
Load
Cin
-
-Vin
-Out
Output Ripple Reduction
A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance.
To reduce output ripple, it is recommended to use 1μF capacitors at the output.
+
+Vin
DC Power
Source
-
+Out
Single Output
DC / DC
Converter
-Vin
Cout
Load
-Out
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the
maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from
measurements obtained in a test setup.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected]
Minmax Technology Co., Ltd.
2014/11/27 REV:7
Page 4 of 4