TM3110PM

Available as:
RF AMPLIFIER
MODEL TM3110PM
Features
Typical Intermodulation Performance at 25 ºC
 Superior Phase Noise Performance
 High Output Power: +30 dBm Typical
 Operating Temp. -55 ºC to +85 ºC
 Environmental Screening Available
Second Order Harmonic Intercept Point ...... +66 dBm (Typ.)
Second Order Two Tone Intercept Point ....... +63 dBm (Typ.)
Third Order Two Tone Intercept Point ........... +45 dBm (Typ.)
Absolute Maximum (No Damage) Ratings
Specifications
CHARACTERISTIC
Frequency (MHz)
TYPICAL
Ta= 25 ºC
MIN/MAX
Ta = -55 ºC to +85 ºC
10 - 200 MHz
10 - 200 MHz
Gain (dB)
15.5
15 Min.
Power @ 1 dB
Comp. (dBm)
+30
+29 Min.
-17
1.8:1
1.8:1
3.5
-16 Max.
2.0:1 Max.
2.0:1 Max.
4.5 Max.
+15
240
+15
250 Max.
Reverse Isolation (dB)
VSWR
In
Out
Noise Figure (dB)
Power
Vdc
mA
TM3110PM, 4 Pin TO-8 (T4)
TN3110PM, 4 Pin Surface Mount (SM3)
BX3110PM, Connectorized Housing (H1)
Note: Care should always be taken to effectively ground the case of each unit.
*Note: Phase Noise Performance typically tested at midband. Bandedge
performance may vary.
Ambient Operating Temperature ................ -55ºC to +100 ºC
Storage Temperature ................................. -62ºC to +125 ºC
Case Temperature .................................................. +125 ºC
DC Voltage .......................................................... +17 Volts
Continuous RF Input Power .................................. +15 dBm
Short Term RF Input Power ........... 100 mW (1 Minute Max.)
Maximum Peak Power .................... 0.2 Watt (3 μsec Max.)
Total Theta jc (TN3110PM).................................+41ºC/Watt
Junction Temp Rise Above Case (TN3110PM).............. 36ºC
Frequency
Typical
-160
-170
-175
-180
-180
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
Guarantee
-155
-165
-170
-175
-175
Guaranteed @ 25 ºC (160 MHz) Phase Noise Performance (dBc/Hz)*
Note: Unit requires a 50 ohm termination at all times.
Typical Performance Data
Gain (dB)
18
-13 0
17
-10
16
-20
15
-30
14
Start 10 MHz
+32
Stop 200 MH z
5
+30
4
+29
+28
3
Sta rt 10 MH z
Stop 2 00 MHz
-1 70
-1 80
-19 0
10 0
Start 10 MHz
Stop 200 MHz
2.0
Output VSWR
Stop 20 0 MHz
Legend
10 k
100k
1M
Typical
Residual Phase Noise Test Conditions:
 Carrier Frequency: 160 MHz
 Power Output +29.0 dBm
 Temperature: 25 oC
1.5
Sta rt 10 MH z
1k
Stop 2 00 MHz
1.75
1.75
1.5
-1 60
Start 10 MHz
Noise Figure (dB)
2
Input VSWR
-1 50
6
+31
2.0
-1 40
-40
1 dB Comp. (dBm)
Phase Noise (dBc/Hz)
Reverse Isolation (dB)
0
Stop 2 00 MHz
Start 1 0 MHz
+25 ºC
 Agilent ES5500 System
+85 ºC - - - - - - -55 ºC
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
Rev.
4/26/10
www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001