F10 - F50 Flow Switches ® DESCRIPTION Magnetrol flow switches are highly reliable devices utilized to sense the start or stop of flow in horizontal pipelines containing oil and petroleum derivatives, chemicals, water, or air. Vane actuated model F10 switches are used on gas or liquid flow applications in 2" or larger pipe sizes. Disc actuated model F50 switches are in-line type used for sensing clean liquids in 2" or smaller pipe sizes. Standard & tailor made designs F E AT U R E S • Actuation on increasing or decreasing flow • Special sensing elements for non-standard or high flow applications • Designed for horizontal pipe applications • Standard anti corrosive protection Model F10: - Field adjustable - Low pressure drop - Process temperature up to +230 °C (+450 °F) - Process pressure up to 69 bar (1000 psi) - Standard flow vanes for 2" thru 10" flow lines Model F50: - No calibration required - Bronze or stainless steel construction - Process temperature up to +400 °C (+750 °F) - Process pressure up to 79,3 bar (1150 psi) - Bodies for flow lines from 3/4" to 2" F10 A G E N C Y A P P R O VA L S Agency ATEX CCE ➀ A P P L I C AT I O N S • • • • • • • • Pump staging or failure Pipeline flow detection Valve failure Loss of pipeline flow Pipe blockage/rupture Pump inlet flow protection Check valve blockage/leakage Alarm on eyewash or shower safety station F50 FM FM/CSA ➁ IEC LRS Approval II 2G Ex d IIC T6 Gb, flameproof enclosure II 1G EEx ia IIC T6, intrinsically safe explosion proof and intrinsically safe Class I, Div. 1, Groups C & D Class II, Div. 1, Groups E, F & G, Type NEMA 7/9 Non-Hazardous area Explosion proof area – Groups B, C, D, E, F & G Type NEMA 4X/7/9 Ex d IIC T6 Lloyds Register of Shipping (marine applications) Russian Authorisation Standards ➁ Other approvals are available, consult factory for more details ➀ For CCE approved units, use the ATEX model numbers. ➁ Consult factory for proper model numbers and classifications. Worldwide level and flow solutions P R I N C I P L E O F O P E R AT I O N F10 The actuating vane is magnetically linked to a pivoted electric (or pneumatic) switch, which is isolated from the process by a non-magnetic barrier tube. As the actuating vane moves with an increase in flow, it drives a magnetic sleeve into the field of a permanent magnet located outside the barrier tube which trips the switch. As flow decreases, the actuating vane returns to a vertical position, allowing the magnet and switch assembly to return to the “No Flow” position. Mechanism switch 4 5 6 Pivot Tension spring Swing out position No flow position Barrier tube (non magnetic) 4 Sleeve (magnetic) 5 6 Magnet Swing in position Flow disc Position with actuating flow present Switch mechanism Adjusting screw Barrier tube (non magnetic) Magnet Magnetic sleeve Actuating vane No flow position Position with actuating flow present F50 The rate of flow through the valve body raises or lowers the disc. This in turn raises or lowers the magnetic sleeve, within its sealed non-magnetic barrier tube. On an increasing flow rate, the magnetic sleeve rises into the field of the permanent magnet, located outside the barrier tube, actuating the attached switch mechanism. When the flow rate drops, below the rate for which the flow disc is calibrated, a reversal of this action occurs. MOUNTING FLOW Input line Additive flow Overflow detection FLOW Leak detection Overflow tank Pump protection Primary tank FLOW E L E C T R I C A L S P E C I F I C AT I O N S Description Specification Signal Output Single SPDT or DPDT contacts or single pneumatic Switch ratings Switch Types (see table on page 3) Approvals (see table on page 1) 2 Cable entries Up to 15 A @ 240 V AC (depending on switch mechanism) Up to 10 A @ 120 V DC (depending on switch mechanism) Dry contact with standard or gold alloy contacts, Mercury, Hermetically sealed, Hermetically sealed with gold or silver plated contacts, Proximity switch, or single pneumatic bleed and non bleed ATEX II 2G Ex d II C T6 Gb, explosion proof ATEX II 1G EEx ia II C T6, intrinsically safe IEC Ex d II C T6, explosion proof FM/CSA, explosion proof LRS, Lloyds Register of Shipment (marine applications) EAC, Russian Authorisation standards Other approvals are available, consult factory. M20 x 1,5 ISO, 1" NPT and 3/4" NPT (or others at request) AVA I L A B L E S W I T C H M E C H A N I S M S Max. Process Temp. ➁ Switch ratings – A res. ➂ Code ➄ F10 F50 24 V DC 240 V AC 120 V AC Micro switch max +120 °C (+250 °F) 6 15 15 B Micro switch max +230 °C (+450 °F) 10 15 15 C Micro switch - DC current max +120 °C (+250 °F) 10 – 10 D Micro switch with gold alloy contacts max +120 °C (+250 °F) 1 – 1 U Hermetically sealed micro switch max +230 °C (+450 °F) not applicable 5 5 5 HS ➃ Hermetically sealed micro switch with max +230 °C (+450 °F) 3 1 1 W silver plated contacts Hermetically sealed micro switch with max +230 °C (+450 °F) 0,5 0,5 0,5 X gold plated contacts 4 – 2,5 F Hermetically sealed micro switch not applicable max +400 °C (+750 °F) Proximity switch - type SJ 3.5 SN max +100 °C (+210 °F) NA NA NA V Pneumatic bleed type (open air) max +200 °C (+400 °F) NA NA NA J Pneumatic non bleed type max +200 °C (+400 °F) NA NA NA K (closed circuit) Type of switch module ➀ ➀ ➁ ➂ ➃ ➄ For applications with heavy vibration, consult factory for suited switch modules. Max process temperature is specified at +40 °C (+100 °F) ambient temperature and for non condensing applications. For more details - see bulletin BE 42-120. For condensing applications, max process temperature is down-rated to +200 °C (+400 °F) @ +40 °C (+100 °F) ambient. For bronze construction, max process temperature is downrated to +260 °C (+500 °F). Type B, C, D & U Type HS Type V Type J & K Type F, W & X AVA I L A B L E H O U S I N G S • • • • • For Non Ex use IP 66 Die cast Aluminium 2 Entries (one plugged) Standard blue anti corrosive coating • Housing heater/drain available, consult factory • • • • • For Exd/Exi use IP 66 Die cast Aluminium 2 Entries (one plugged) Standard blue anti corrosive coating • ATEX II 2G Ex d II C T6 Gb • ATEX II 1G EEx ia II C T6 • IEC Ex d II C T6 • • • • For Exd use IP 66 Cast Iron One entry (2 entries at request) • Standard blue anti corrosive coating • ATEX II 2G Ex d II C T6 Gb • • • • For pneumatic switches IP 53 (NEMA 3R) IP 55 optional at request Alu base / cold rolled steel cover • Standard blue anti corrosive coating • • • • • For Exd use IP 66 (NEMA 7/9) Die cast Aluminium 2 Entries (one plugged) Standard blue anti corrosive coating • FM, Class I, Div. 1, Groups C & D • FM, Class II, Div. 1, Groups E, F & G 3 S E L E C T I O N D ATA – F 1 0 Actuating flow rates (water service) – m3/h Model F10 units may be adjusted in service to actuate within the minimum and maximum flow rates given below (based on schedule 40 pipe). A specific gravity correction factor is applied for liquids other than water (1.00 specific gravity). Flow Pipe increase decrease size inches Min. Max. Min. Max. 2.00 4.8 14.3 3.6 10.9 2.50 5.2 16.8 4.5 12.7 3.00 7.3 20.0 5.4 14.8 3.50 8.6 22.7 6.4 17.0 4.00 10.2 27.2 7.5 19.3 5.00 13.8 34.1 9.8 25.0 6.00 17.9 40.9 12.5 29.5 8.00 27.2 52.2 18.6 36.3 10.00 38.6 70.4 25.0 47.7 12.00 52.2 86.3 34.1 56.8 Flow Pipe increase decrease size inches Min. Max. Min. Max. 14.00 61.3 97.6 38.6 63.6 16.00 77.2 115.8 49.9 72.6 18.00 97.6 133.9 61.3 84.0 20.00 118.0 156.6 72.6 97.6 22.00 140.7 177.1 86.3 109.0 24.00 165.7 204.3 102.2 124.9 26.00 193.0 233.8 118.0 140.7 28.00 222.5 263.3 133.9 158.9 30.00 252.0 292.8 152.1 177.1 For higher/lower flow rates, consult factory. Specific gravity correction for actuating flow rates – m3/h To determine the actuating flow rates for liquids other than water (approximate viscosity of 20 cP or less) a specific gravity correction factor must be applied to the water flow rates given in the table. Specific Gravity Multiplication Factor Specific Gravity Multiplication Factor 0.45 1.49 1.00 1.00 0.40 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 1.58 1.41 1.35 1.29 1.24 1.20 1.15 1.12 1.08 1.05 0.95 1.05 1.10 1.15 1.20 1.25 1.30 1.35 1.40 1.45 1.03 0.98 0.95 0.93 0.91 0.89 0.88 0.86 0.85 0.83 P H Y S I C A L S P E C I F I C AT I O N S – F 1 0 Description Measured variable Physical range Specification Flow rate Increasing flow From 4,8 m3/h (2" pipe size) up to 292,8 m3/h (30" pipe size) Decreasing flow From 3,6 m3/h (2" pipe size) up to 177,1 m3/h (30" pipe size) Process temperature Process pressure (for higher ratings & steam applications; consult factory) Up to 69 bar @ +230 °C (1000 psi @ +450 °F) Process connection material Wetted materials Vane Carbon steel or stainless steel Trim and magnetic sleeve 302 SST (1.4300) or 304 SST (1.4301) 316 SST (1.4401) EXPEDITE SHIP PLAN (ESP) Several mechanical switches are available for quick shipment, within max. 4 weeks after factory receipt of purchase order, through the Expedite Ship Plan (ESP). Models covered by ESP service are conveniently grey coded in the selection data charts. To take advantage of ESP, simply match the grey coded model number codes (standard dimensions apply). ESP service may not apply to orders of five units or more. Contact your local representative for lead times on larger volume orders, as well as other products and options. S E L E C T I O N D ATA – F 1 0 Select pneumatic switch mechanism & enclosure Pneumatic switch type Series J (open air) 4 Series K (closed circuit) Max supply pressure bar (psi) Max liquid temperature °C (°F) Bleed orifice Ø mm (inches) NEMA 3R (IP 53) 6,9 (100) +200 (+400) 1,60 (0.063) JGF 4,1 (60) +200 (+400) 2,39 (0.094) JHF 6,9 (100) +200 (+400) – KOF S E L E C T I O N D ATA – F 1 0 A complete measuring system consists of: 1. Order code for F10 models 2. Order code for modified models or adders: put an "X" in front of the closest matching order code and specify the modifications/adders separately eg. XF10-AD22-BK9 X = with material certification EN 10204 / DIN 50049-3.1.B 1. Order code for F10 flow switch BASIC MODEL NUMBER F 1 0 vane actuated flow switch – field adjustable setpoint Consult factory for steam applications. MATERIALS OF CONSTRUCTION Code Process connection material Carbon steel 316 SST (1.4401) A D Vane Trim and magnetic sleeve 302 SST (1.4300) or 304 SST (1.4301) 316 SST (1.4401) PIPE SIZE AND PROCESS CONNECTION D 2 2 D 2 4 Pipe size Process connection 2" 4" D 2 6 D 2 0 10" E 5 8 8" E 5 4 4" E 5 6 6" E 5 0 2 E 6 0 10" E 7 6 6" E 6 8 2" NPT E 7 4 - 150 lbs RF 2 1/2" - 150 lbs RF 10" 2 1/2" E 7 8 - 150 lbs RF E 7 0 SWITCH MECHANISM & ENCLOSURE C D HS U V W X 1 x SPDT 1 x DPDT Weather proof (IP 66) cast Aluminium 1 x SPDT 1 x DPDT – 8" 2 1/2" - 600 lbs RF 10" 2 1/2" - 600 lbs RF ATEX/IEC (IP 66) II 2G Ex d II C T6 Gb cast Aluminium ATEX (IP 66) II 1G EEx ia II C T6 cast Aluminium II 2G Ex d II C T6 Gb cast Iron 1" NPT M20 x 1,5 3/4" NPT B8B BDB BN9 BF9 – – BD5 BW5 B2B BAB CAB C8B CDB H7A HM2 D2B H7C U2B U8B – W2B 1 x DPDT X8B 1 x SPDT 2 1/2" - 600 lbs RF M20 x 1,5 1 x SPDT 1 x DPDT 2 1/2" - 600 lbs RF 1" NPT D8B 1 x SPDT 4" M20 x 1,5 1 x DPDT 1 x DPDT 2 1/2" - 300 lbs RF 1" NPT C2B 1 x SPDT 2 1/2" - 300 lbs RF M20 x 1,5 1 x SPDT 1 x DPDT 6" 2 1/2" - 300 lbs RF - for electric switch mechanisms (see below) - for pneumatic switch mechanisms (see left page) Select electric switch mechanism & enclosure B 4" complete order code for F10 models F 1 0 qty and switch type 2 1/2" - 300 lbs RF 2" NPT E 6 6 2 1/2" - 150 lbs RF 1/2" 8" E 6 4 2" NPT 8" Process connection 2" NPT 2" NPT 6" D 2 8 Pipe size W8B X2B DAB DDB HM6 UAB UDB – WAB WDB XAB XDB BK9 BC9 – CK9 CC9 C2T DN9 DF9 – CN9 DK9 HFC HGC CF9 DC9 HA9 HB9 – – HB3 HB4 HM3 – – XN9 XF9 X8T XK9 WF9 XC9 CKB CNB W2T WN9 BKB BNB CW5 WC9 – CU5 1" NPT CD5 WK9 – CK5 BU5 cast Alu. CDT UC9 UF9 CAT BK5 NEMA 7/9 C8T UK9 UN9 – FM (IP 66) U2T U8T VCS W8T X2T – – – UAT UDT VES WAT WDT XAT XDT DK5 DD5 HB7 UK5 DU5 DW5 HB8 UU5 UD5 UW5 WD5 WW5 – WK5 XK5 XD5 – WU5 XU5 XW5 DKB DNB HM7 UKB UNB – WKB WNB XKB XNB 5 S E L E C T I O N D ATA – F 5 0 Specific gravity correction for actuating flow rates – m3/h To determine the actuating flow rates for liquids other than water (approximate viscosity of 20 cP or less), a specific gravity correction factor must be applied to the water flow rates given in the table. For gas/air applications, consult factory. Specific Gravity Multiplication Factor Specific Gravity Multiplication Factor 0.45 1.49 1.00 1.00 0.40 1.58 0.50 0.95 1.41 0.55 1.05 1.35 0.60 0.88 1.35 1.08 0.90 0.89 1.30 1.12 0.85 0.91 1.25 1.15 0.80 0.93 1.20 1.20 0.75 0.95 1.15 1.24 0.70 0.98 1.10 1.29 0.65 1.03 0.86 1.40 1.05 0.85 1.45 0.83 P R E S S U R E D R O P TA B L E S – F 5 0 1400 1400 1200 pressure drop in mbar pressure drop in mbar 1200 1000 1000 800 600 400 200 0 0 0,5 1 1,5 1400 2 3/4" 2,5 3 3,5 4 4,5 5 flow in m3/h 5,5 6 NPT connection 6,5 7 400 200 0 0 0,5 1 1,5 1400 2 2,5 3 flow in m3/h 3,5 4 4,5 5 16 flow in m3/h 24 26 5,5 1" NPT connection 6 6,5 32 34 7 7,5 8 1200 pressure drop in mbar pressure drop in mbar 600 7,5 1200 1000 1000 800 600 400 200 0 800 0 2 4 6 8 10 12 14 16 18 20 flow in m3/h 22 24 11/2" NPT connection 26 28 30 32 800 600 400 200 0 34 0 2 4 6 8 10 12 14 18 20 22 28 30 2" NPT connection 36 38 40 42 P H Y S I C A L S P E C I F I C AT I O N S – F 5 0 Description Measured variable Physical range Process temperature Process pressure (for higher ratings consult factory) Body material Wetted materials Specification Increasing flow Decreasing flow Bronze models Stainless steel models Disc and trim Magnetic sleeve Flow rate From 0,25 m3/h (3/4" pipe size) up to 5,63 m3/h (2" pipe size) From 0,18 m3/h (3/4" pipe size) up to 4,77 m3/h (2" pipe size) Up to 27,6 bar @ +40 °C (400 psi @ +100 °F) Up to +260 °C @ 13,8 bar (+500 °F @ 200 psi) Up to 79,3 bar @ +40 °C (1150 psi @ +100 °F) Up to +400 °C @ 41,3 bar (+750 °F @ 600 psi) Bronze or stainless steel 316 SST (1.4401) 316 SST (1.4401) or 400 series SST Select pneumatic switch mechanism & enclosure S E L E C T I O N D ATA – F 5 0 Max supply pressure bar (psi) Max liquid temperature °C (°F) Bleed orifice Ø mm (inches) Series J (open air) 6,9 (100) +200 (+400) 1,60 (0.063) JDG JDE 4,1 (60) +200 (+400) 2,39 (0.094) Series K (closed circuit) 6,9 (100) +200 (+400) – JEG KOE➁ KOE 2,8 (40) +200 (+400) – KOG – ➀ Use switch codes with material code D for F50-AC2E / F50-AC2F / F50-AD2E / F50-AD2F ➁ Only in combination with F50-AC2E / F50-AC2F / F50-AD2E / F50-AD2F 6 NEMA 3R (IP 53) material code D material code A ➀ Pneumatic switch type JEE S E L E C T I O N D ATA – F 5 0 A complete measuring system consists of: 1. Order code for F50 models. 2. Order code for modified models or adders: put an "X" in front of the closest matching order code and specify the modifications/adders separately eg. XF50-AB2C-A2P X = process connection 1" - 150 lbs RF ANSI flanges 1. Order code for F50 flow switch BASIC MODEL NUMBER mechanical disc actuated flow switch MATERIALS OF CONSTRUCTION Body material Code F 5 0 Flow disc and trim Bronze & carbon steel nut 316 SST (1.4401) A D Magnetic sleeve 300 series SST 316 SST (1.4401) 400 series SST 316 SST (1.4401) PROCESS CONNECTION AND ACTUATING FLOW RATES Actuating flow rate Process connection A 2 B 3/4" A 2 C 3/4" 3/4" A 2 D A 2 E 3/4" 3/4" A 2 F B 2 A NPT NPT NPT NPT 0,77 m /h NPT 1,11 m /h 0,84 m /h 0,23 m /h 0,18 m /h 0,57 m /h 0,48 m /h 0,84 m /h 1,25 m /h 1,02 m /h 3 1,61 m /h 1,32 m /h 3 2,79 m /h 4,79 m /h 4,06 m3/h 0,43 m3/h 0,36 m3/h 0,70 m /h 0,61 m3/h 3 1,16 m3/h 0,98 m3/h 1,91 m /h 1,61 m3/h 3 2" NPT D 2 F 2,38 m3/h 3 2" NPT D 2 E 3 NPT 1,48 m3/h 3 2" NPT D 2 D 3 0,91 m3/h 0,52 m3/h 1,73 m3/h 2" NPT D 2 C 3 NPT 2" NPT D 2 B 0,68 m /h 3 1,07 m /h 0,25 m3/h 3 11/2" NPT D 2 A 3 SWITCH MECHANISM & ENCLOSURE F 5 0 C 2 F 0,32 m3/h 3 11/2" decreasing 0,61 m3/h 11/2" NPT C 2 E 3 0,39 m3/h 1" NPT C 2 D 3 3 1" NPT B 2 F 0,59 m /h 11/2" increasing 0,30 m3/h 11/2" NPT C 2 C 3 3 1" NPT B 2 E 0,41 m /h 3 11/2" NPT C 2 B 3 Actuating flow rate Process connection C 2 A 0,27 m3/h 3 1" NPT B 2 D 0,52 m /h 0,18 m3/h 0,36 m3/h 1" NPT B 2 C decreasing 0,25 m3/h 1" NPT B 2 B increasing 3,25 m /h 2,75 m3/h 3 2" NPT 5,63 m3/h 4,77 m3/h - for electric switch mechanisms (see below) - for pneumatic switch mechanisms (see left page) complete order code for F50 models 2 Select electric switch mechanism & enclosure All models with material code A ➀ qty and switch type B C D F U V W X ATEX/IEC (IP 66) All models with material code D ATEX (IP 66) FM (IP 66) Weather proof (IP 66) II 2G Ex d IIC T6 Gb II 1G EEx ia II C T6 II 2G Ex d IIC T6 Gb cast Aluminium cast Aluminium cast Aluminium ATEX/IEC (IP 66) ATEX (IP 66) FM (IP 66) NEMA 7/9 Weather proof (IP 66) II 2G Ex d IIC T6 Gb II 1G EEx ia II C T6 II 2G Ex d IIC T6 Gb NEMA 7/9 cast Iron cast Alu. cast Aluminium cast Aluminium cast Aluminium cast Iron cast Alu. M20 x 1,5 3/4" NPT M20 x 1,5 3/4" NPT 1" NPT M20 x 1,5 1" NPT M20 x 1,5 1" NPT M20 x 1,5 1" NPT 1" NPT M20 x 1,5 1" NPT M20 x 1,5 1" NPT M20 x 1,5 1" NPT 1 x SPDT B2P BAP BHC BAC - - BK7 BU7 BKP B2Q BAQ BH9 BA9 - - BK5 BU5 BKQ 1 x DPDT B8P BDP BJC BBC - - BD7 BW7 BNP B8Q BDQ BJ9 BB9 - - BD5 BW5 BNQ 1 x SPDT C2P CAP CHC CAC C2L CAL CK7 CU7 CKP C2Q CAQ CH9 CA9 C2S CAS CK5 CU5 CKQ 1 x DPDT C8P CDP CJC CBC C8L CDL CD7 CW7 CNP C8Q CDQ CJ9 CB9 C8S CDS CD5 CW5 CNQ 1 x SPDT - - - - - - - - - D2Q DAQ DH9 DA9 - - DK5 DU5 DKQ 1 x DPDT - - - - - - - - - D8Q DDQ DJ9 DB9 - - DD5 DW5 DNQ 1 x SPDT F2P FAP FHC FAC - - FK7 FU7 FKP F2Q FAQ FH9 FA9 - - FK5 FU5 FKQ 1 x DPDT F8P FDP FJC FBC - - FD7 FW7 FNP F8Q FDQ FJ9 FB9 - - FD5 FW5 FNQ 1 x SPDT U2P UAP UHC UAC U2L UAL UK7 UU7 UKP U2Q UAQ UH9 UA9 U2S UAS UK5 UU5 UKQ 1 x DPDT U8P UDP UJC UBC U8L UDL UD7 UW7 UNP U8Q UDQ UJ9 UB9 U8S UDS UD5 UW5 UNQ - - - - - VFS VHS - - - - - - - V5S VBS - - - 1 x SPDT W2P WAP WHC WAC W2L WAL WK7 WU7 WKP W2Q WAQ WH9 WA9 W2S WAS WK5 WU5 WKQ WNQ 1 x DPDT - - - - - - - - - W8Q WDQ WJ9 WB9 W8S WDS WD5 WW5 1 x SPDT X2P XAP XHC XAC X2L XAL XK7 XU7 XKP X2Q XAQ XH9 XA9 X2S XAS XK5 XU5 XKQ 1 x DPDT - - - - - - - - - X8Q XDQ XJ9 XB9 X8S XDS XD5 XW5 XNQ ➀ Use switch codes with material code D for F50-AC2E / F50-AC2F / F50-AD2E / F50-AD2F 7 DIMENSIONS in mm (inches) Pipe size Dim. A max. 46 (1.81) 2" Equivalent max. wall schedule 2 1/2" 49 (1.94) 48 (1.88) 3" 3 1/2" 48 (1.88) 4" 51 (2.00) 5" 52 (2.06) 6" 54 (2.12) 56 (2.19) 8" 59 (2.31) 10" over 10" 59 (2.31) 40 (1.59) 180 160 53 (2.09) 68 (2.66) 180 120 118 (4.66) 120 195 (7.69) 100 FLOW A 145 (5.72) 100 V W 94 (3.69) 120 X Y Z 79 (3.12) 180 Pipe size (horizontal lines only) 67 ø ± 1,5 (2.64 ø ± 0.06) 2" NPT 3000# bonney threadolet or equal (supplied by customer) 63 (2.50) 44 (1.75) V W 133 (5.25) 187 (7.38) Dim "B" Vane width 38 (1.50) 3" pipe and up Y X V Z V W 81 (3.19) 51 (2.00) 97 (3.81) 30 (1.19) 3/4" or 1" NPT internal pipe (both ends) 51 (2.00) 146 (5.75) V W Housing type Models WeatherproofFM (NEMA 7/9) ATEX (Cast Alu) F10 F50 202 7.94 ATEX (Cast Iron) All 249 Pneumatics Switch Module J F10 F50 F10 F50 216 165 216 165 Pneumatics Switch Module K 76 ø (3.00) 5 (0.19) minimum Flow vane 2" and 2 1/2" pipe Y W Y Z 2" NPT 254 (10.00) - X Z X Dim. B mm inches mm inches mm 257 10.12 42 1.66 151 9.80 45 1.77 8.50 6.50 8.50 6.50 39 1.54 øX inches 1 1/2"or 2" NPT internal pipe (both ends) Y Z mm inches 5.93 109 4.29 M20 x 1,5 (*) or 1" NPT (2 entries - 1 plugged) (*) not for FM (NEMA 7/9) 143 5.63 110 4.33 M20 x 1,5 or 3/4" NPT (single entry - 2 entries at request) 110 4.33 118 4.65 130 5.12 Allow 200 mm (7.87") overhead clearance / All housings are 360 ° rotatable 1/4" NPT QUALITY ASSURANCE - ISO 9001 THE QUALITY ASSURANCE SYSTEM IN PLACE AT MAGNETROL GUARANTEES THE HIGHEST LEVEL OF QUALITY DURING THE DESIGN, THE CONSTRUCTION AND THE SERVICE OF CONTROLS. OUR QUALITY ASSURANCE SYSTEM IS APPROVED AND CERTIFIED TO ISO 9001 AND OUR TOTAL COMPANY IS COMMITTED TO PROVIDING FULL CUSTOMER SATISFACTION BOTH IN QUALITY PRODUCTS AND QUALITY SERVICE. PRODUCT WARRANTY :2008 ALL MAGNETROL MECHANICAL LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR FIVE FULL YEARS FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION. MAGNETROL SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION OR USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME MAGNETROL PRODUCTS. BULLETIN N°: EFFECTIVE: SUPERSEDES: UNDER RESERVE OF MODIFICATIONS Heikensstraat 6, 9240 Zele, België -Belgique Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93 • E-Mail: [email protected] DEUTSCHLAND Alte Ziegelei 2-4, D-51491 Overath Tel. +49 (0)2204 / 9536-0 • Fax. +49 (0)2204 / 9536-53 • E-Mail: [email protected] INDIA B-506, Sagar Tech Plaza, Saki Naka Junction, Andheri (E), Mumbai - 400072 Tel. +91 22 2850 7903 • Fax. +91 22 2850 7904 • E-Mail: [email protected] ITALIA Via Arese 12, I-20159 Milano Tel. +39 02 607.22.98 • Fax. +39 02 668.66.52 • E-Mail: [email protected] RUSSIA 198095 Saint-Petersburg, Marshala Govorova street, house 35A, office 427 Tel. +7 812 320 70 87 • E-Mail: [email protected] U.A.E. UNITED KINGDOM DAFZA Office 5EA 722 • PO Box 293671 • Dubai Tel. +971-4-6091735 • Fax +971-4-6091736 • E-Mail: [email protected] Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL Tel. +44 (0)1444 871313 • Fax +44 (0)1444 871317 • E-Mail: [email protected] www.magnetrol.com BENELUX FRANCE OUR NEAREST REPRESENTATIVE BE 47-116.8 SEPTEMBER 2015 December 2014