720 MHz SAW Filter 10 MHz Bandwidth Part Number: SF0720BA03165S DESCRIPTION • • • 720 MHz SAW bandpass filter with minimum 3 dB bandwidth of 10 MHz. 5 x 5 mm ceramic LCC package, 8 pads. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 3 dB/div Phase 10 deg/div Delay 100 ns/div Center = 720 MHz, 20 MHz/div (250 kHz incr) S11 (620-820 MHz) S22 (620-820 MHz) Spectrum Microwave, Inc. 324 Clark Street, Worcester, MA 01606, USA Phone 508-852-5400 Fax 508-852-8456 www.SpectrumMicrowave.com DSSF0720BA03165S Rev - 8-Jan-2010 ECN 36691 Page 1 of 3 720 MHz SAW Filter 10 MHz Bandwidth Part Number: SF0720BA03165S SPECIFICATION Parameter Center Frequency, FC 1 Minimum Insertion Loss Absolute Delay 1 dB Bandwidth 2 3 dB Bandwidth 2 Min Typ Max - 720 - Units MHz - 2.9 4 dB - 0.06 0.1 - 6.3 - MHz us 10 14.7 - MHz Lower 3 dB Frequency 2 - 712.7 715 MHz Upper 3 dB Frequency 2 725 727.4 - MHz - 22.1 24 MHz Amplitude Ripple (Fc± 4 MHz) - 1.5 3 dB p-p Phase Deviation (Fc± 4 MHz) - 3 10 deg p-p 20 dB Bandwidth 2 Group Delay Ripple (Fc± 4 MHz) - 15 30 Rejection (500-700 MHz) 2 40 45 - dB ns p-p Rejection (740-950 MHz) 2 40 48 - dB Input Return Loss (Fc± 4 MHz) 10 14 - dB Output Return Loss (Fc± 4 MHz) 10 14 - dB - -35 - Temperature Coefficient of frequency ppm/˚C Source/Load Impedance 50 ohms Ambient Temperature 25 ˚C Notes: 1. Defined as the average of the lower and upper 3 dB frequencies at room ambient. 2. All dB levels are defined relative to the insertion loss. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 - 85 85 +13 Units ˚C ˚C dBm MATCHING CIRCUIT 2 Input 50 Ω Single-ended 6 Output 50 Ω Single-ended All other pads GND GND Ls1 = 8.2 nH, Ls2 = 8.2 nH Notes: • Recommend ±2% matching tolerances. Typical inductor Q=40. • Values shown are for reference only and may change depending on board layout. Spectrum Microwave, Inc. 324 Clark Street, Worcester, MA 01606, USA Phone 508-852-5400 Fax 508-852-8456 www.SpectrumMicrowave.com DSSF0720BA03165S Rev - 8-Jan-2010 ECN 36691 Page 2 of 3 720 MHz SAW Filter 10 MHz Bandwidth Part Number: SF0720BA03165S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are ±0.15 mm except where indicated. Pad Configuration: Input: 2 Output: 6 To be grounded: all other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating MARKING SMI 3165S YYDDD 1 Manufacturer ID Part Number Date Code (YY=year, DDD=day) ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave, Inc. 324 Clark Street, Worcester, MA 01606, USA Phone 508-852-5400 Fax 508-852-8456 www.SpectrumMicrowave.com DSSF0720BA03165S Rev - 8-Jan-2010 ECN 36691 Page 3 of 3