Packaging

TransGuard
PACKAGING
• Chips
• Axial Leads
• Radial Leads
142
®
Paper Carrier Configuration
8mm Tape Only
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
±0.20mm (±0.008)
P0
D0
T
P2
E1
BOTTOM
COVER
TAPE
TOP
COVER
TAPE
F
W
E2
B0
G
T1
T1
A0
CENTER LINES
OF CAVITY
CAVITY SIZE
SEE NOTE 1
P1
User Direction of Feed
8mm Paper Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
8mm
D0
1.50 +0.10
-0.0
(0.059 +0.004
-0.0
)
mm (inches)
E
P0
P2
1.75 ± 0.10
4.00 ± 0.10
2.00 ± 0.05
(0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002)
T1
G. Min.
R Min.
0.10
(0.004)
Max.
0.75
(0.030)
Min.
25.0 (0.984)
See Note 2
Min.
VARIABLE DIMENSIONS
Tape Size
8mm
P1
See Note 4
4.00 ± 0.10
(0.157 ± 0.004)
mm (inches)
E2 Min.
6.25
(0.246)
F
W
3.50 ± 0.05
(0.138 ± 0.002)
NOTES:
1. The cavity defined by A0, B0, and T shall be configured to provide sufficient clearance
surrounding the component so that:
a) the component does not protrude beyond either surface of the carrier tape;
b) the component can be removed from the cavity in a vertical direction without
mechanical restriction after the top cover tape has been removed;
c) rotation of the component is limited to 20º maximum (see Sketches A & B);
d) lateral movement of the component is restricted to 0.5mm maximum
(see Sketch C).
8.00 +0.30
-0.10
(0.315 +0.012
-0.004 )
A0 B0
T
See Note 1
1.10mm
(0.043) Max.
for Paper Base
Tape and
1.60mm
(0.063) Max.
for Non-Paper
Base Compositions
2. Tape with or without components shall pass around radius “R” without damage.
3. Bar code labeling (if required) shall be on the side of the reel opposite the sprocket
holes. Refer to EIA-556.
4. If P1 = 2.0mm, the tape may not properly index in all tape feeders.
Top View, Sketch "C"
Component Lateral
0.50mm (0.020)
Maximum
0.50mm (0.020)
Maximum
Bar Code Labeling Standard
AVX bar code labeling is available and follows latest version of EIA-556
143
Embossed Carrier Configuration
8 & 12mm Tape Only
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
±0.2mm (±0.008)
EMBOSSMENT
P0
T2
T
D0
P2
DEFORMATION
BETWEEN
EMBOSSMENTS
E1
A0
F
TOP COVER
TAPE
B1
T1
W
B0
K0
S1
E2
CENTER LINES
OF CAVITY
P1
MAX. CAVITY
SIZE - SEE NOTE 1
B1 IS FOR TAPE READER REFERENCE ONLY
INCLUDING DRAFT CONCENTRIC AROUND B0
D1 FOR COMPONENTS
2.00 mm x 1.20 mm AND
LARGER (0.079 x 0.047)
User Direction of Feed
8 & 12mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
D0
8mm
and
12mm
1.50 +0.10
-0.0
(0.059 +0.004
-0.0
)
mm (inches)
E
P0
P2
1.75 ± 0.10
4.0 ± 0.10
2.0 ± 0.05
(0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002)
S1 Min.
T Max.
T1
0.60
(0.024)
0.60
(0.024)
0.10
(0.004)
Max.
VARIABLE DIMENSIONS
Tape Size
B1
Max.
D1
Min.
E2
Min.
mm (inches)
F
P1
See Note 5
R
Min.
See Note 2
T2
W
Max.
A0 B0 K0
8mm
4.35
(0.171)
1.00
(0.039)
6.25
(0.246)
3.50 ± 0.05
4.00 ± 0.10
(0.138 ± 0.002) (0.157 ± 0.004)
25.0
(0.984)
2.50 Max.
(0.098)
8.30
(0.327)
See Note 1
12mm
8.20
(0.323)
1.50
(0.059)
10.25
(0.404)
5.50 ± 0.05
4.00 ± 0.10
(0.217 ± 0.002) (0.157 ± 0.004)
30.0
(1.181)
6.50 Max.
(0.256)
12.3
(0.484)
See Note 1
NOTES:
1. The cavity defined by A0, B0, and K0 shall be configured to provide the following:
Surround the component with sufficient clearance such that:
a) the component does not protrude beyond the sealing plane of the cover tape.
b) the component can be removed from the cavity in a vertical direction without mechanical
restriction, after the cover tape has been removed.
c) rotation of the component is limited to 20º maximum (see Sketches D & E).
d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch F).
2. Tape with or without components shall pass around radius “R” without damage.
3. Bar code labeling (if required) shall be on the side of the reel opposite the round sprocket holes.
Refer to EIA-556.
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. If P1 = 2.0mm, the tape may not properly index in all tape feeders.
Top View, Sketch "F"
Component Lateral Movements
0.50mm (0.020)
Maximum
0.50mm (0.020)
Maximum
144
Packaging of Chip Components
Automatic Insertion Packaging
REEL DIMENSIONS
mm (inches)
Tape
Size
A
Max.
B*
Min.
C
D*
Min.
N
Min.
8mm
330
(12.992)
1.5
(0.059)
13.0 +0.50
-0.20
(0.512 +0.020
-0.008 )
12mm
20.2
(0.795)
W1
W2
Max.
W3
8.40 +1.5
-0.0
(0.331 +0.059
-0.0
)
14.4
(0.567)
7.90 Min.
(0.311)
10.9 Max.
(0.429)
12.4 +2.0
-0.0
(0.488 +0.079
-0.0
)
18.4
(0.724)
11.9 Min.
(0.469)
15.4 Max.
(0.607)
50.0
(1.969)
Metric dimensions will govern.
English measurements rounded and for reference only.
145
TransGuard®
AVX Multilayer Ceramic Transient Voltage Suppressors
PACKAGING - AXIAL LEADS / TAPE AND REEL
CLASS I / RS-296
5mm ± 0.5mm
(0.200" ± 0.020")
52.4mm ± 1.5mm
(2.063" ± 0.059")
6.35mm ± 0.4mm
(0.250" ± 0.016")
1.4mm
(0.055" MAX.)
1.2mm
(0.047" MAX.)
1.6mm
(0.063" MAX.)
356mm
(14.00" MAX.)
76mm
(3.000")
25.4mm
(1.000")
84mm
(3.300")
70mm
(2.750")
A.
B*.
C.
D1-D2.
E.
F.
G.
H.
I.
J.
K.
Optional
Design
H
D1
F
C
E
A
B
K
Leader Tape: 300mm min. (12")
Splicing: Tape Only
Missing Parts: 0.25% of component count max.No consecutive missing parts
J
I
G
146
D2
Radial Leads/Packaging
REEL DIRECTION
QUANTITY PER REEL
PART
PCS
VR15, VR20
3000
CG20, CG21
Leads on top of
carrier strip,
body away
Unreel from
LEFT to RIGHT
OVER TOP of reel
S
T
S
K
E
D
Q
R
C
L
W
A
B
F
G
F
O
E
DESCRIPTION
A – Reel Diameter
B – Reel Outside Width
C – Reel Inside Width
D – Core Diameter (O.D.)
E – Hub Recess Diameter
F – Hub Recess Depth
G – Arbor Hole Diameter
DIMENSIONS (MM)
304.80 - 355
50.80 maximum
38.10 - 46.02
102.01 maximum
86.36 maximum
9.50 minimum
25.40 - 30.48
B
X
DIMENSIONS (MM)
A. Feed Hole Pitch
B. Feed Hole Diameter
C. Feed Hole Location
12.70 ± .20
3.99 ± .20
9.02 ± .51
D. Component Lead Spacing
+.79
5.00+.79
-.20 or 2.54 -.20
E. Component Lead Location
3.81 ±.51 or 5.00 ±.51
for 2.54 lead spacing
2.00 maximum
F. Component Lead Protrusion
(edge of carrier to cut end of lead)
K. Component Body Location
C
M
DESCRIPTION
A
D
N
L. Carrier Tape Width
M. Carrier Tape Assembly Thickness
N. Carrier Tape Spliced Thickness
O. Carrier Tape Spliced Length
Q. Adhesive Tape Border
R. Component Bent Leads (either direction)
S. Component Misalignment
T. Component Pitch
W. Adhesive Tape Width
X. Carrier Tape Thickness
Y. Cumulative Pitch over 20 Pitches
6.35 ±.41
18.01 +1.02
-.51
.71 ± .20
1.42 maximum
50.80 - 88.90
3.00 maximum
.79 maximum
.99 maximum
12.70 ±.99
5.00 minimum
.51 ±.10
254 ±2.00
147