Outline Dimensions Vishay High Power Products D2PAK, TO-262 DIMENSIONS FOR D2PAK in millimeters and inches Conforms to JEDEC outline D2PAK (SMD-220) (2)(3) E B Pad layout A A (E) c2 11.00 MIN. (0.43) A (3) L1 4 9.65 MIN. (0.38) (D1) (3) Detail A D H 1 2 17.90 (0.70) 15.00 (0.625) (2) 3 3.81 MIN. (0.15) L2 B B 2.32 MIN. (0.08) A 2 x b2 c 2.64 (0.103) 2.41 (0.096) (3) E1 C View A - A 2xb ± 0.004 M B 0.010 M A M B Plating 2x e Base Metal (4) b1, b3 H Gauge plane Seating plane Lead assignments Diodes 1. - Anode (two die)/open (one die) 2., 4. - Cathode 3. - Anode SYMBOL MILLIMETERS MIN. c1 (4) (c) B 0° to 8° MAX. L3 Lead tip A1 L (b, b2) L4 Section B - B and C - C Scale: None Detail “A” Rotated 90 °CW Scale: 8:1 INCHES MIN. MAX. NOTES SYMBOL MILLIMETERS MIN. MAX. INCHES MIN. MAX. NOTES A 4.06 4.83 0.160 0.190 D1 6.86 8.00 0.270 0.315 3 A1 0.00 0.254 0.000 0.010 E 9.65 10.67 0.380 0.420 2, 3 E1 7.90 8.80 0.311 0.346 3 b 0.51 0.99 0.020 0.039 b1 0.51 0.89 0.020 0.035 b2 1.14 1.78 0.045 0.070 b3 1.14 1.73 0.045 0.068 c 0.38 0.74 0.015 0.029 c1 0.38 0.58 0.015 0.023 c2 1.14 1.65 0.045 0.065 D 8.51 9.65 0.335 0.380 4 2.54 BSC 0.100 BSC H 14.61 15.88 0.575 0.625 4 L 1.78 2.79 0.070 0.110 L1 - 1.65 - 0.066 4 L2 1.27 1.78 0.050 0.070 2 L4 L3 Notes (1) Dimensioning and tolerancing per ASME Y14.5 M-1994 (2) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L1, D1 and E1 (4) Dimension b1 and c1 apply to base metal only (5) Datum A and B to be determined at datum plane H (6) Controlling dimension: inch Document Number: 95014 Revision: 31-Mar-09 e (7) 0.25 BSC 4.78 5.28 3 0.010 BSC 0.188 0.208 Outline conforms to JEDEC outline TO-263AB For technical questions concerning discrete products, contact: [email protected] For technical questions concerning module products, contact: [email protected] www.vishay.com 1 Outline Dimensions D2PAK, TO-262 Vishay High Power Products DIMENSIONS FOR TO-262 in millimeters and inches Modified JEDEC outline TO-262 (Datum A) (2) (3) E A A c2 B E A (3) L1 Seating plane D 1 2 3 C L2 B D1 (3) B C L (2) A c 3 x b2 3xb E1 A1 (3) Section A - A 2xe Plating 0.010 M A M B (4) b1, b3 Base metal Lead assignments Diodes 1. - Anode (two die)/open (one die) 2., 4. - Cathode 3. - Anode Lead tip SYMBOL c1 c (4) (b, b2) Section B - B and C - C Scale: None MILLIMETERS INCHES MIN. MAX. MIN. MAX. A 4.06 4.83 0.160 0.190 A1 2.03 3.02 0.080 0.119 b 0.51 0.99 0.020 0.039 b1 0.51 0.89 0.020 0.035 b2 1.14 1.78 0.045 0.070 b3 1.14 1.73 0.045 0.068 c 0.38 0.74 0.015 0.029 c1 0.38 0.58 0.015 0.023 c2 1.14 1.65 0.045 0.065 NOTES 4 4 4 D 8.51 9.65 0.335 0.380 D1 6.86 8.00 0.270 0.315 3 E 9.65 10.67 0.380 0.420 2, 3 E1 7.90 8.80 0.311 0.346 3 e 2.54 BSC 0.100 BSC L 13.46 14.10 0.530 0.555 L1 - 1.65 - 0.065 L2 3.56 3.71 0.140 0.146 Notes (1) Dimensioning and tolerancing as per ASME Y14.5M-1994 (2) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L1, D1 and E1 (4) Dimension b1 and c1 apply to base metal only (5) Controlling dimension: inches www.vishay.com 2 2 (6) 3 Outline conform to JEDEC TO-262 except A1 (maximum), b (minimum) and D1 (minimum) where dimensions derived the actual package outline For technical questions concerning discrete products, contact: [email protected] For technical questions concerning module products, contact: [email protected] Document Number: 95014 Revision: 31-Mar-09