70 MHz SAW Filter 1.5 MHz Bandwidth Part Number SF0070BA13048S DESCRIPTION • • • 70 MHz SAW bandpass filter with 1.5 MHz bandwidth. 13.3 x 6.5 mm SMP. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay Deviation : S11 (200Ω balanced) 1.6 10 1 12 500 MHz/div dB/div dB/div deg/div ns/div S22 (200Ω balanced) IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0070BA13048S Rev - 18-Aug-2006 Page 1 of 3 70 MHz SAW Filter 1.5 MHz Bandwidth Part Number SF0070BA13048S SPECIFICATION Parameter Center Frequency (Fc) 1 Insertion Loss 1 dB Bandwidth 3 dB Bandwidth 36 dB Bandwidth Passband Ripple 2 Phase Deviation from Linear 2 Group Delay Variation 2 Absolute Delay System Source and Load Impedance, Balanced Temperature Coefficient of Frequency (Tc) 3 Ambient Temperature (Tref) Notes: Min 69.90 1.00 1.50 - Typ 70.00 9.2 1.34 1.69 3.10 0.8 6.5 320 2.1 200 -23 25 Max 70.10 9.7 65.4 3.30 1 8 425 - Units MHz dB MHz MHz MHz dB p-p deg p-p ns p-p us Ω ppm/˚C °C 1. Average of lower and upper 3 dB frequencies. 2. Evaluated over 60% of the 3 dB bandwidth. 3. Typical change of filter frequency response with temperature is ∆f = (T-Tref) * Tc * Fc, in ppm. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level Min Max -40 - 85 10 Units ˚C dBm MATCHING CIRCUIT Input 200 Ω Balanced Typical component values: (Minimum inductor Q = 45) Output 200 Ω Balanced L1 L3 C1 = = = 100 120 41 nH nH pF L2 L4 C2 = = = 100 120 39 nH nH pF Notes: 1. Recommend use of 2% tolerance matching components. 2. Component values shown are for guidance only and may change depending on board layout. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0070BA13048S Rev - 18-Aug-2006 Page 2 of 3 70 MHz SAW Filter 1.5 MHz Bandwidth Part Number SF0070BA13048S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are ±0.15 mm except for the overall length and width, which are nominal values. Pad Configuration: Inputs: Outputs: Ground: Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating 10,1 5,6 2,3,4,7,8,9 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. © 2006 All rights reserved. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0070BA13048S Rev - 18-Aug-2006 Page 3 of 3