Evaluation Kit

THAN0211_Rev.1.00_E
THC63LVD1027(-Q) Evaluation Kit
LVDS Dual Link Evaluation Board
Parts Number: THEVA1027-V2
1. General Description
THEVA1027-V2 is designed to evaluate THC63LVD1027(-Q) for transmission video data.
THC63LVD1027(-Q) chipset can transmit 35bit data via dual channel LVDS.
The maximum input clock frequency of THC63LVD1027(-Q) is 135MHz, and the maximum output clock
frequency of THC63LVD1027-Q is 100MHz.
2. Features
THC63LVD1027
・Low power single 3.3V CMOS design
・Power down mode
・Wide dot clock range suited for TV signal(480i to 1080p), PC signal(VGA to UXGA)
・PLL requires no external components
・Single/Dual LVDS (Open-LDI) in, Single/Dual LVDS (Open-LDI) out
・Distribution signal duplication mode
・Support Reduced Swing LVDS for Lower EMI
・64 Pin TSSOP with Exposed PAD (0.5mm lead pitch)
3. Overview
Figure 1 THEVA1027-V2
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
1/7
Security E
THAN0211_Rev.1.00_E
4. Power Supply Setup
This chapter shows power supply condition.
Caution: Please check if there is no power-GND short on below red trace before supplying any power.
3.3V Power Supply to Each Board
Each evaluation board requires 3.3V power supply. Please use “CON1” connector typically.
Figure 2 THEVA1027-V2 power supply for evaluation board
Power Supply from / to Connector
3.3V power supply can be connected to CON103 and CON102 by using W101 and W102 solder jumper.
THEVA1027-V2
W101: Connect the 3.3V power supply with pin#1 and 2 of CON103.
W102: Connect the 3.3V power supply with pin#29 and 30 of CON102.
Figure 3 THEVA1027-V2 power supply from / to each connector
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
2/7
Security E
THAN0211_Rev.1.00_E
5. Function Setting
Setting pin of each board is shown in yellow area of Figure 4.
Setting pins
Figure 4 THEVA1027-V2 position of function setting pin
Pin#2 of each 3HEADER is connected to IC’s setting pin.
Each setting pin’s high or low setting can set by connecting pin#2 of 3HEADER and high level or low level.
(a)3HEADER Description
(b)High Level Setting
(c)Low Level Setting
Figure 5 Schematic diagram of High / Low setting description
6. Status Indicate LED
LED “D101” indicates 3.3V power supply status.
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
3/7
Security E
THAN0211_Rev.1.00_E
7. Function
This chapter shows function setting of THEVA1027-V2.
Table 1 THEVA1027-V2 function setting description
Silk
Symbol
PD
PD
RS
Function
Power down function setting
H : Normal Operation
L : Power Down Mode (All outputs are Hi-Z)
LVDS swing mode.
RS
RS
LVDS Swing
H
350mV
L
200mV
Pixel data mode select
MODE1
MODE0
MODE1
MODE0
MODE1
L
L
H
L
H
MODE0
RCLK2+/-
Function
L
L
L
H
H
Clock input
Hi-Z
Hi-Z
Clock input
-
Dual-in / Dual -out
Distribution
Single-in / Dual -out
Dual-in / Single-out
Reserved
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
4/7
Security E
D
C
B
A
1
GND
52271-3069(NC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RA1RA1+
RB1RB1+
RC1RC1+
RCLK1RCLK1+
RD1RD1+
RE1RE1+
RA2RA2+
RB2RB2+
RC2RC2+
RCLK2RCLK2+
RD2RD2+
RE2RE2+
SML-310MT
D101
R101
150Ω
GND
W101
Solder Jumper
VDD3.3
C102
10uF
GND
CON103
GND
GND
2
CON101
VCC
1
L101
2
2
MPZ1608R471A
VDD3.3
GND
C101
10uF
VCC
3
RE2+
RE2-
RD2+
RD2-
RCLK2+
RCLK2-
RC2+
RC2-
RB2+
RB2-
RA2+
RA2-
RE1+
RE1-
RD1+
RD1-
RCLK1+
RCLK1-
RC1+
RC1-
RB1+
RB1-
RA1+
RA1-
3
R113
100Ω
R112
100Ω
R111
100Ω
R110
100Ω
R109
100Ω
R108
100Ω
R107
100Ω
R106
100Ω
R105
100Ω
R104
100Ω
R103
100Ω
R102
100Ω
PD
2
4
GND
4
Header101
MODE1 2
3HEAD(NC)
VCC
1
3
VDD3.3
CAP2
RS
CAP2
0.01uF
0.1uF
C111
C110
Header102
MODE0 2
CAP31
CAP31
PD
C107 0.1uF VCC
RA1RA1+
RB1RB1+
RC1RC1+
RCLK1RCLK1+
RD1RD1+
RE1RE1+
RA2RA2+
RB2RB2+
RC2RC2+
RCLK2RCLK2+
RD2RD2+
RE2RE2+
C109 0.1uF VCC
0.1uF
C105
0.01uF
C103
3HEAD(NC)
GND
1
3
1
1
3
RS
CAP
GND
VDD
RA1RA1+
RB1RB1+
RC1RC1+
RCLK1RCLK1+
RD1RD1+
RE1RE1+
RA2RA2+
RB2RB2+
RC2RC2+
RCLK2RCLK2+
RD2RD2+
RE2RE2+
VDD
GND
CAP
PD
IC101
5
Header103
RS
3HEAD(NC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
5
2
GND
Header104
3HEAD(NC)
GND
CAP
GND
VDD
TA1TA1+
TB1TB1+
TC1TC1+
TCLK1TCLK1+
TD1TD1+
TE1TE1+
TA2TA2+
TB2TB2+
TC2TC2+
TCLK2TCLK2+
TD2TD2+
TE2TE2+
VDD
GND
MODE1
MODE0
THC63LVD1027
EXPGND
65
5/7
1
Copyright(C) 2016 THine Electronics, Inc.
3
282836-2(NC)
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
MODE1
MODE0
VCC
TA1TA1+
TB1TB1+
TC1TC1+
TCLK1TCLK1+
TD1TD1+
TE1TE1+
TA2TA2+
TB2TB2+
TC2TC2+
TCLK2TCLK2+
TD2TD2+
TE2TE2+
VCC
CAP63
CAP63
0.1uF
C106
0.1uF
6
4.7nF
C119
C120
GND
0.1uF
4.7nF
C108
C118
C104 0.01uF
6
Title
Date:
File:
A3
Size
GND
TA1TA1+
TB1TB1+
TC1TC1+
TCLK1TCLK1+
TD1TD1+
TE1TE1+
TA2TA2+
TB2TB2+
TC2TC2+
TCLK2TCLK2+
TD2TD2+
TE2TE2+
7
52271-3069(NC)
CON102
8
8
Revision
1.00
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VDD3.3
W102
Solder Jumper
2016/03/07
Sheet 1 of 1
C:\Users\..\THEVA1027-V2_R100.SchDocDrawn By:
Number
THEVA1027(-Q)-V2
7
D
C
B
A
THAN0211_Rev.1.00_E
8. Schematic
Figure 6 THEVA1027-V2 Schematic
THine Electronics, Inc.
Security E
THAN0211_Rev.1.00_E
9. Bills of Materials
Table 2 THEVA1027-V2 BOM
Comment
Capacitor2012
Capacitor1005
Capacitor1005
Capacitor1005
282836-2
CN-FFC(1.0)30PD
LED1608
3HEAD
THC63LVD1027
Inductor1608
Resistor1608
Description
2012
1005
1005
1005
282836-2
CN-FFC(1.0)30PD
1608
3HEAD
TSSOP64
1608
1608
Value
10uF
0.01uF
0.1uF
4.7nF
282836-2(NC)
52271-3069(NC)
SML-310MT
3HEAD(NC)
Note
16V
16V
16V
16V
5mm pitch
1mm pitch
Green
2.54mm pitch
MPZ1608R471A
150Ω
0.1W
Resistor1005
1005
100Ω
0.1W
Designator
C101, C102
C103, C104, C111
C105, C106, C107, C108, C109, C110, C120
C118, C119
CON101
CON102, CON103
D101
Header101, Header102, Header103, Header104
IC101
L101
R101
R102, R103, R104, R105, R106, R107, R108,
R109, R110, R111, R112, R113
Q'ty
2
3
7
2
1
2
1
4
1
1
1
12
10. Set Items
Table 3 THEVA1027-V2 Set Items
TYPE
Part No.
DC Connector
282836-2
FFC Connector for LVDS Link
52271-3069
FFC 30pin 1mm Pitch for LVDS Link
98267-0475
It’s possible to mount these parts on this board and use.
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
6/7
Security E
THAN0211_Rev.1.00_E
11. Notices and Requests
Please kindly read, understand and accept this “Noticees and Requests” before using this product.
For the Material:
1. The product specifications described in this material are subject to change without prior notice.
2. The circuit diagrams described in this material are examples of the application which may not always
apply to design of respective customers. THine Electronics, Inc. (“THine”) is not responsible for
possible errors and omissions in this material. Please note if the errors or omissions should be found in
this material, THine may not be able to correct them immediately.
3. This material contains THine’s copyright, know-how or other proprietary. Copying or disclosing of the
contents of this material to any third party without THine’s prior permission is strictly prohibited.
For the Product:
1. This product is solely designed for evaluation purpose, and other purposes including mass production
and distribution are not intended.
2. This product has been solely manufactured for electric design engineers but not for end-users.
3. This product is not radiation-tolerant product.
4. This product is presumed to be used for general electric device, not for applications which require
extremely high-reliability/safety (including medical device concerned with critical care, aerospace
device, or nuclear power control device). Also, when using this product for any device concerned with
control and/or safety of transportation mean, traffic signal device, or other various types of safety
device, such use must be after applying appropriate measures to the product.
5. This product has been designed with the utmost care to accomplish the purpose of evaluation of IC
products manufactured by THine Electronics, Inc., however, THine MAKES NO WARRANTIES OR
REPRESENTATIONS WITH REGARD TO ANY PERFORMANCE OR FUNCTION OF THIS
PRODUCT IN ANY CIRCUMSTANCE.
6. This product has been manufactured with the utmost care in quality control and product reliability,
however, there may be faults or defects with a low but fixed probability, as inevitable phenomenon
concerned with semiconductor manufacturing processes. Therefore, Customers are encouraged to have
sufficiently redundant or error-preventive design applied to the use of the product so as not to have
THine’s product cause any social or public damage. Replacement of the product is only available in
case of obvious defects of mount devices at the point of unpacking the product. Neither replacement
nor failure analysis of the product is available in any other case of defects with the product and/or the
product’s components.
7. Customers are asked, if required, to judge by themselves on whether this product falls under the
category of strategic goods under the Foreign Exchange and Foreign Trade Control Law.
8. Please Note that if infringement of any third party’s industrial ownership should occur by using this
product, THine will be exempted from any responsibility unless it directly relates to the production
process or functions of the product.
9. Developing, designing and manufacturing of Customers’ own products, equipments or system by using
of this product is strictly prohibited in any way.
THine Electronics, Inc.
[email protected]
THine Electronics, Inc.
Copyright(C) 2016 THine Electronics, Inc.
7/7
Security E