DLA 06019

REVISIONS
LTR
DESCRIPTION
A
Added an approved source and updated.
B
Added missing PINs and 100V parts.
DATE
APPROVED
3 February 2014
Michael A. Radecki
6 May 2016
Michael A. Radecki
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.100
REV STATUS
OF PAGES
PMIC N/A
Original date of
drawing
12 July 2006
REV
B
B
B
B
B
B
B
B
B
PAGES
1
2
3
4
5
6
7
8
9
PREPARED BY
Patrick Kyne
CHECKED BY
Kenneth A. Bernier
APPROVED BY
Michael A. Radecki
SIZE
A
REV
AMSC N/A
DESIGN ACTIVITY
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OH
TITLE
CAPACITOR, FIXED, CERAMIC, CHIP,
HIGH FREQUENCY
CODE IDENT. NO.
037Z3
DWG NO.
B
PAGE
06019
1
OF
9
5910-2016-E05
1. SCOPE
1.1 Scope. This drawing and MIL-PRF-123 describe the requirements for high frequency ceramic chip capacitors.
1.2 Part or Identifying Number (PIN) The complete PIN is as follows:
06019
BP
102
B
J
Z
Drawing
number
Dielectric
(see 1.2.1)
Capacitance
value
(see 1.2.2)
Voltage
(see 1.2.3)
Capacitance
tolerance
(see 1.2.4)
Termination
finish
(see 1.2.5)
1.2.1 Dielectric. The dielectric type is identified by the following 2 letters as defined in 3.3.1: BP or BG.
1.2.2 Capacitance value. The nominal capacitance value, expressed in picofarads (pF) is identified by a three digit number; the first
two digits represent significant figures and the last digit specifies the number of zeros to follow. When the nominal value is less than 10
pF, the letter “R” is used to indicate the decimal point and the succeeding digit(s) of the group represent significant figure(s). 1R0
indicates 1.0 pF; R75 indicates .75 pF; and 0R5 indicates 0.5 pF. See table IV for values.
1.2.3 Voltage. The rated voltage for continuous operation at +125°C is identified by a single letter as shown in table I.
TABLE I. Rated voltage.
Symbol
Rated voltage (volts, dc)
A
B
K
50
100
150
1.2.4 Capacitance tolerance. The capacitance tolerance is identified by a single letter in accordance with table II.
TABLE II. Capacitance tolerance.
Symbol
Capacitance tolerance
B
.10 pF
C
D
F
.25 pF
.50 pF
±1 percent
G
±2 percent
J
±5 percent
±10 percent
±20 percent
K
M
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
2
1.2.5 Termination finish. Termination finish is identified by a single letter as shown in table III.
TABLE III. Termination finish.
Symbol
Termination finish
M
Palladium-silver
N
Silver-nickel-gold
U
Base metallization-barrier metal-solder coated (tin/lead alloy, with a minimum of 4 percent lead). Solder
has a melting point of +200°C or less. Solder coat thickness is a minimum of 60 microinches.
Z
Base metallization-barrier metal-tinned (tin/lead alloy, with a minimum of 4 percent lead)
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not
include documents cited in other sections of this specification or recommended for additional information or as examples. While every
effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
requirements of documents in sections 3 and 4 of this specification, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this
document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or
contract (see 6.2).
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-123
-
MIL-PRF-55681
-
MIL-PRF-55681/4
-
Capacitors, Fixed, Ceramic Dielectric, (Temperature Stable and General Purpose), High Reliability,
General Specification For
Capacitor, Chip, Multiple Layer, Fixed, Unencapsulated, Ceramic Dielectric, Established Reliability
and Non-Established Reliability, General Specification For
Capacitor, Chip, Multiple Layer, Fixed, Ceramic Dielectric, Established Reliability and NonEstablished Reliability, Styles CDR11, CDR12, CDR13, and CDR14 (High Frequency)
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-202-305
-
Method 305, Capacitance
(Copies of these documents are available online at http://quicksearch.dla.mil/.)
2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this
document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes
applicable laws and regulations unless a specific exemption has been obtained.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
3
Inches
.005
.010
.015
.020
.025
.030
.035
.055
.057
.102
.110
mm
0.13
0.25
0.38
0.51
0.64
0.76
0.89
1.40
1.45
2.59
2.79
L 3/
W
.055 ±.015
.055 ±.015
Dimensions
T
Min
Max
.020
.057
Y
.010 -.005 +.010
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Dimension L tolerance shall be ±.025 when termination finish U or Z is specified (see 1.2.5).
FIGURE 1. Dimensions and configuration.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
4
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-123 including those for deliverables,
data, production lot definition, traceability, and as specified herein. Unless otherwise stated, these capacitors shall be capable of
meeting all design, electrical, environmental, and mechanical requirements of MIL-PRF-123.
3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-123 and herein (see
figure 1).
3.2.1 Tin plated finishes. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable
provided that the minimum lead content is 4 percent (see 6.3).
3.3 Electrical characteristics.
3.3.1 Dielectric type. The dielectric type shall be BG (90 ±20ppm/°C) or BP (0 ±30 ppm/°C) ceramic in accordance with MIL-PRF-123.
Symbol
Capacitance change with reference to +25°C
Step A through step D of
MIL-PRF-123 table XVIII
BG
90 ± 20 ppm/°C
Percent rated
voltage
100
BP
0 ± 30 ppm/°C
100
Step E through step G of
MIL-PRF-123 table XVIII
0 ± 30 ppm/°C
90 ± 20 ppm/°C
3.3.2 Capacitance. Capacitance shall be in accordance with table IV when measured in accordance with method 305 of MIL-STD-202.
The following conditions shall apply:
≤ 1,000 pF
> 1,000 pF
1 MHz ± 50 kHz
1 V rms ± .2 V rms
1 kHz ± 50 Hz
1 V rms ± .2 V rms
3.3.3 Dissipation factor (+25°C). The dissipation factor shall be as follows:
BP
BG
All capacitance values: ≤ 0.15%
All capacitance values: ≤ 0.05%
6
3.3.4 Insulation resistance. At +25°C: 10 megohms, minimum
5
At +125°C: 10 megohms, minimum
3.3.5 Equivalent series resistance. In accordance with MIL-PRF-55681.
3.3.6 Series Resonance. In accordance with MIL-PRF-55681.
3.4 Marking. Marking shall be as specified in MIL-PRF-123. In addition, these capacitors shall be marked with a contrasting color dot
placed on the side of the capacitor to indicate the vertical plate orientation to that side. When laser marked, the marking shall be on the
surface which is parallel to the plane of the embedded electrodes (this is the larger area which is normally the imprint area). If the capacitor
is so marked, the vertical plane orientation is defined; therefore the contrasting color dot on the capacitor to indicate vertical plate orientation
to that side is optional. Packaging shall be marked as specified in MIL-PRF-123 except the PIN shall be as specified in 1.2 and the “JAN”
brand is not applicable.
3.5 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF55681/4 Qualified Products List for “S” failure rate level.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
5
3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of
supply.
3.7 Changes to product. Any changes in material or processes that alter the form, fit, or function such that it no longer meets the
requirements specified in this drawing will require approval prior to implementation.
3.8 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally preferable, or
biobased materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and
maintenance requirements, and promotes economically advantageous life cycle costs.
3.9 Workmanship. In accordance with MIL-PRF-123.
4. VERIFICATION
4.1 Qualification inspection. Qualification inspection is not required.
4.2 In-process inspection. In-process inspection shall be in accordance with MIL-PRF-123.
4.3 Conformance inspection.
4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of
MIL-PRF-123. In addition, the following tests and sampling requirements shall be included in group B inspection as subgroup 4 and
subgroup 5:
Subgroup 4
Solderability; 6 samples, accept/reject is 0.
Subgroup 5
ESR (UHF and RF) and resonance frequency; 6 samples, accept/reject is 0.
The remaining group C inspection requirements of MIL-PRF-123 shall be satisfied by the continued qualification of the supplier to the “S”
failure rate for the equivalent MIL-PRF-55681/4 capacitors.
4.4 Methods of inspection. Methods of inspection shall be as specified in MIL-PRF-123 and MIL-PRF-55681 for ESR and resonance
frequency.
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When
packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible
packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s
packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data
retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or
by contacting the responsible packaging activity.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
6
TABLE IV. Capacitor characteristics.
DSCC drawing
PIN
06019 - 1/
Capacitance
(pF)
Capacitance
tolerance
Rated temperature
and voltagetemperature limits
Rated
voltage
(V dc)
B - 0R1 - B B - 0R2 - B B - 0R3 - - B - 0R4 - - B - 0R5 - - B - 0R6 - - B - 0R7 - - B - 0R8 - - B - 0R9 - - B - 1R0 - - B - 1R1 - - B - 1R2 - - B - 1R3 - - B - 1R4 - - B - 1R5 - - B - 1R6 - - B - 1R7 - - B - 1R8 - - B - 1R9 - - B - 2R0 - - B - 2R1 - - B - 2R2 - - B - 2R4 - - B - 2R7 - - B - 3R0 - - B - 3R3 - - B - 3R6 - - B - 3R9 - - B - 4R3 - - B - 4R7 - - B - 5R1 - - B - 5R6 - - B - 6R2 - - B - 6R8 - - B - 7R5 - - B - 8R2 - - B - 9R1 - - B - 100 - - B - 110 - - B - 120 - - B - 130 - - B - 150 - - B - 160 - - B - 180 - - B - 200 - - B - 220 - - B - 240 - - B - 270 - - B - 300 - - B - 330 - - B - 360 - - -
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
B
B
B, C
B, C
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, D
B, C, J, K, M
B, C, J, K, M
B, C, J, K, M
B, C, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
See footnote at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
7
TABLE IV. Capacitor characteristics - Continued.
DSCC drawing
PIN
06019 - 1/
B - 390 - - B - 430 - - B - 470 - - B - 510 - - B - 560 - - B - 620 - - B - 680 - - B - 750 - - B - 820 - - B - 910 - - B - 101 - - BP111 - - BP121 - - BP131 - - BP151 - - BP161 - - BP181 - - BP201 - - BP221 - - BP241 - - BP271 - - BP301 - - BP331 - - BP361 - - BP391 - - BP431 - - BP471 - - BP511 - - BP561 - - BP621 - - BP681 - - BP751 - - BP821 - - BP911 - - BP102 - - -
Capacitance
(pF)
39
43
47
51
56
62
68
75
82
91
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
1,000
Capacitance
tolerance
Rated temperature
and voltagetemperature limits
Rated
voltage
(V dc)
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BG, BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
BP
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 150
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
50, 100
1/ Complete PIN shall include additional symbols to indicate voltage-temperature limits
(where applicable), rated voltage, capacitance tolerance (where applicable), and
termination finish
6. NOTES
(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)
6.1 Intended use. This drawing covers high frequency capacitors that are primarily intended for use in resonant circuits with high Q factor
and stability of capacitance with respect to temperature (-55°C to +125°C), frequency, and life. The capacitors covered by this drawing are
intended for use in high reliability applications. Capacitors conforming to this drawing are intended for use when military specifications do not
exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended
exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military
specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be
used for new design.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
8
6.2 Ordering data. The contract or purchase order should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for notification of change of product to acquiring activity, if applicable.
c. Requirements for packaging and packing.
6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems
after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating
conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the
formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information
on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin).
6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by a contractor-prepared
specification or drawing.
6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and
the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at
[email protected] or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, or
by telephone (614) 692-4709 or DSN 850-4709.
6.6 Changes from previous issue. The margins of this drawing are marked with vertical lines to indicate where changes from the
previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any
inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the
entire content irrespective of the marginal notations and relationship to the last previous issue.
6.7 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become
available. Assistance in the use of this drawing may be obtained online at [email protected], or by contacting DLA Land and
Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709.
Vendor CAGE
Vendor name and address
Vendor designation 1/
29990
American Technical Ceramics
One Norden Lane
Huntington Station, NY 11746-2142
100A (BG)
700A (BP)
04222
AVX Ceramics Corp.
P.O. Box 867
th
801 17 Avenue South
Myrtle Beach, SC 29577-0867
AQ12******H***
60212
Presidio Components Incorporated
7169 Construction Court
San Diego, CA 92121-2615
SR0505*********
1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests
are met.
DEFENSE SUPPLY CENTER, COLUMBUS
SIZE
CODE IDENT NO.
DWG NO.
COLUMBUS, OHIO
A
037Z3
06019
REV B
PAGE
9