REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested source of supply. 10 Jan 90 David E. Moore B Deleted suggested source of supply. 29 Jun 90 David E. Moore C Deleted and added suggested sources of supply. Modified 3.1.2 and figure 1. Added note for standoff. Editorial changes throughout. 24 Feb 92 David E. Moore D Changes in accordance with NOR 5910-R015-96 23 May 96 Andrew R. Ernst E Altered maximum length. Added and removed suggested sources of supply. 25 August 99 Kendall A. Cottongim F Removed suggested source of supply. 10 May 00 Kenneth A. Bernier G Editorial changes made throughout. 6 October 2004 Kendall A. Cottongim H Changed drawing to source control with approved sources of supply. Added pure tin prohibition paragraph 3.1.3 and manufacturer eligibility paragraph 3.14. Editorial changes. 15 Dec 09 Michael A. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV H H H H H H H PAGES 1 2 3 4 5 6 7 DESIGN ACTIVITY PMIC N/A Original date of drawing: 22 December 1987 PREPARED BY ROBERT E. GRILLOT CHECKED BY HERALDINE JOHNSON APPROVED BY DAVID W. WITHROW SIZE A REV AMSC N/A Source control drawing DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 TITLE CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (8 CAPACITOR SECTIONS) BX CODE IDENT. NO. 14933 DWG NO. H PAGE 87119 1 OF 7 5910-E449 1. SCOPE 1.1 Scope. This drawing, MIL-PRF-39014, and MIL-PRF-39014/5 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87119- XX Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39014 - Capacitors, Fixed, Ceramic Dielectric (General Purpose) Established Reliability and Nonestablished Reliability, General Specification for. MIL-PRF-39014/5 - Capacitors, Fixed, Ceramic Dielectric (General Purpose), Established Reliability, Styles CKR11, CKR12, CKR14, CKR15, and CKR16. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Electronics and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-39014 and herein (see figure 1). 3.1.1 Leads. Leads shall be as specified on figure 1. 3.1.2 Case. Molded or conformally coated. 3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.4 Operating temperature range. The operating temperature range shall be -55°C to +125°C. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 2 Inches .002 .003 .004 .010 .012 .015 .018 mm 0.05 0.08 0.10 0.25 0.30 0.38 0.46 Inches .058 .060 .100 .115 .135 .300 1.050 mm 1.47 1.52 2.54 2.92 3.43 7.62 26.67 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Standoff shape is optional. The minimum height of the standoff shall be .015 (0.38 mm). 4. Lead spacing .100 ± .010 (25.4 ± 0.25) noncumulative. FIGURE 1. Case dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 3 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 100 V dc at +85°C, 50 V dc at +125°C. 3.2.2 Dielectric type. BX, in accordance with MIL-PRF-39014/5. 3.2.3 Voltage temperature limits. In accordance with MIL-PRF-39014/5. 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25°C. 3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25°C, rated voltage: 100,000 megohms or 1,000 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. Capacitors shall withstand a dc test potential of 250 percent of rated voltage for a period of not less than 1 second nor more than 5 seconds at +25°C. The charging current shall not exceed 50 milliamperes. 3.2.8 Capacitance tolerance. K = ±10 percent, M = ±20 percent. 3.3 Solderability of terminals. In accordance with MIL-PRF-39014. 3.4 Vibration. In accordance with method 204 of MIL-STD-202, test condition B (10 to 20,000 Hz, 15 g’s). 3.5 Shock. In accordance with MIL-PRF-39014. 3.6 Immersion cycling. In accordance with MIL-PRF-39014. 3.7 Moisture resistance. In accordance with MIL-PRF-39014. 3.8 Life. 200 percent of rated voltage applied at +125°C for 1,000 hours. 3.9 Thermal shock. In accordance with method 107 of MIL-STD-202, test condition B except low temperature is -55°C. 3.10 Voltage conditioning. In accordance with MIL-PRF-39014, 200 percent of rated voltage. 3.11 Terminal strength. Capacitors shall withstand a steady pull of 5 pounds for 5 seconds in a direction parallel to the leads. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified herein (see 1.2), the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-123, MIL-PRF-39014, or MIL-PRF-49470 Qualified Products Database for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification sampling and inspection are not required. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 4 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-39014, provided they are listed in this drawing. PPM testing and calculation is not applicable. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). TABLE I. Electrical characteristics. DSCC drawing 8711901 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 Capacitance Capacitance tolerance .001 µF .001 µF .0012 µF .0012 µF .0015 µF .0015 µF .0018 µF .0018 µF .0022 µF .0022 µF .0027 µF .0027 µF .0033 µF .0033 µF .0039 µF .0039 µF .0047 µF .0047 µF .0056 µF K M K M K M K M K M K M K M K M K M K DSCC drawing 8711920 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Capacitance Capacitance tolerance .0056 µF .0068 µF .0068 µF .0082 µF .0082 µF .01 µF .01 µF .015 µF .015 µF .022 µF .022 µF .033 µF .033 µF .047 µF .047 µF .068 µF .068 µF .1 µF .1 µF M K M K M K M K M K M K M K M K M K M 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CDROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 5 c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of change of product to acquiring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at [email protected] or if in writing to: Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 850-0561. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be achieved online at [email protected] or by contacting Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 8500561. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 6 DSCC drawing PIN 8711901 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Vendor similar type 1/ Vendor CAGE SPC11X102KHA SPC11X102MHA SPC11X122KHA SPC11X122MHA SPC11X152KHA SPC11X152MHA SPC11X182KHA SPC11X182MHA SPC11X222KHA SPC11X222MHA SPC11X272KHA SPC11X272MHA SPC11X332KHA SPC11X332MHA SPC11X392KHA SPC11X392MHA SPC11X472KHA SPC11X472MHA SPC11X562KHA SPC11X562MHA SPC11X682KHA SPC11X682MHA SPC11X822KHA SPC11X822MHA SPC11X103KHA SPC11X103MHA SPC11X153KHA SPC11X153MHA SPC11X223KHA SPC11X223MHA SPC11X333KHA SPC11X333MHA SPC11X473KHA SPC11X473MHA SPC11X683KHA SPC11X683MHA SPC11X104KHA SPC11X104MHA 96095 Vendor name and address Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87119 REV H PAGE 7