Package Drawing Designator: CA and CB Type: 3-pin with 2 current path terminals, PFF leadform 14.0±0.2 3.0±0.2 1.50±0.10 4.0±0.2 5 4 1º±2° A NNNNNNN TTT - AAA 3.5±0.2 17.5±0.2 13.00±0.10 LLLLLLL YYWW Branded Face 4.40±0.10 1 B Standard Branding Reference View 2.9±0.2 5º±5° 1 2 +0.060 0.381 –0.030 3 10.00±0.10 3.5±0.2 7.00±0.10 N = Device part number T = Temperature code A = Amperage range L = Lot number Y = Last two digits of year of manufacture W = Week of manufacture = Supplier emblem For Reference Only; not for tooling use (reference DWG-9111, DWG-9110) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal intrusion B Branding scale and appearance at supplier discretion 0.51±0.10 1.9±0.2 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: CA and CB Type: 3-pin with 2 current path terminals, PSF leadform 14.0±0.2 3.0±0.2 4.0±0.2 1.50±0.10 4 5 A 2.75±0.10 NNNNNNN TTT - AAA 23.50±0.5 13.00±0.10 LLLLLLL 4.40±0.10 YYWW Branded Face 1 2.9±0.2 5º±5° 1 2 +0.060 0.381 –0.030 3 10.00±0.10 3.5±0.2 7.00±0.10 B Standard Branding Reference View N = Device part number T = Temperature code A = Amperage range L = Lot number Y = Last two digits of year of manufacture W = Week of manufacture = Supplier emblem For Reference Only; not for tooling use (reference DWG-9111, DWG-9110) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal intrusion B Branding scale and appearance at supplier discretion 0.51±0.10 1.9±0.2 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: CA and CB Type: 3-pin with 2 current path terminals, PSS leadform 14.0±0.2 3.0±0.2 4.0±0.2 5 4 1.50±0.10 A NNNNNNN TTT - AAA 2.75±0.10 23.50±0.5 LLLLLLL 13.00±0.10 YYWW 4.40±0.10 1 Branded Face 3.18±0.10 11.0±0.05 B Standard Branding Reference View N = Device part number T = Temperature code A = Amperage range L = Lot number Y = Last two digits of year of manufacture W = Week of manufacture = Supplier emblem +0.060 0.381 –0.030 1 2 3 10.00±0.10 For Reference Only; not for tooling use (reference DWG-9111, DWG-9110) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown 7.00±0.10 A Dambar removal intrusion B Branding scale and appearance at supplier discretion 0.51±0.10 1.9±0.2 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SA Type: 4-pin SIP Ø9.0 Branded Face 9.0 NNNNNNN LLLLLL (Pin side opposite) 2.0 Ø0.9 A 1 Standard Branding Reference View N = Device part number L = Lot number 7.25 5.00 0.41 1 2 3 4 0.38 1.27 TYP 8.1 3.0 For Reference Only; not for tooling use (reference dwg. 52-9000-0048) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Branding scale and appearance at supplier discretion Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SB Type: 4-pin SIP Ø8.96±0.1 Branded Face NNNNNNN 7.0 LLLLLL (Pin side opposite) 2.0 Ø0.9 A 1 Standard Branding Reference View N = Device part number L = Lot number 8.8 7.0 1 2 3 4 0.41 0.38 1.27 TYP 8.09±0.1 3.0 For Reference Only; not for tooling use (reference DWG-9018) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Branding scale and appearance at supplier discretion Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SE Type: 4-pin SIP 7.00±0.05 B 10.00±0.05 3.3±0.1 Branded Face 1.3±0.1 A 4.9±0.1 1 6.23±0.10 2 3 4 0.9±0.1 LLLLLLL NNN YYWW +0.06 0.38 –0.04 24.65±0.10 D 0.60±0.10 Standard Branding Reference View = Supplier emblem L = Lot identifier N = Last three numbers of device part number and optional subtype codes Y = Last two digits of year of manufacture W = Week of manufacture 11.60±0.10 1.0 REF For Reference Only, not for tooling use (reference DWG-9001) Dimensions in millimeters A Dambar removal protrusion (16X) 2.00±0.10 B Metallic protrusion, electrically connected to pin 4 and substrate (both sides) C Thermoplastic Molded Lead Bar for alignment during shipment D Branding scale and appearance at supplier discretion 1.0 REF A 1.60±0.10 C 1.27±0.10 0.71±0.10 0.71±0.10 5.50±0.10 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SG Type: 4-pin SIP 5.50±0.05 B 8.00±0.05 5.80±0.05 Branded Face 1.70±0.10 4.70±0.10 1 2 3 4 A 0.60±0.10 0.71±0.05 LLLLLLL NNN YYWW +0.06 0.38 –0.04 0.40±0.10 15.30±0.10 D Standard Branding Reference View = Supplier emblem L = Lot identifier N = Last three numbers of device part number and optional subtype codes Y = Last two digits of year of manufacture W = Week of manufacture 24.65±0.10 For Reference Only, not for tooling use (reference DWG-9002) Dimensions in millimeters A Dambar removal protrusion (16X) B Metallic protrusion, electrically connected to pin 4 and substrate (both sides) C Thermoplastic Molded Lead Bar for alignment during shipment D Branding scale and appearance at supplier discretion 1.0 REF A 1.60±0.10 C 1.27±0.10 0.71±0.10 0.71±0.10 5.50±0.10 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SH Type: 4-pin SIP 5.50±0.05 B 8.00±0.05 Branded Face 5.80±0.05 1.70±0.10 5.00±0.10 4.00±0.10 1 2 3 4 A 0.60±0.10 0.71±0.05 LLLLLLL NNN YYWW +0.06 0.38 –0.04 24.65±0.10 D = Supplier emblem L = Lot identifier N = Last three numbers of device part number and optional subtype codes Y = Last two digits of year of manufacture W = Week of manufacture 1.00±0.10 13.10±0.10 Standard Branding Reference View For Reference Only, not for tooling use (reference DWG-9003) Dimensions in millimeters A Dambar removal protrusion (16X) B Metallic protrusion, electrically connected to pin 4 and substrate (both sides) C Thermoplastic Molded Lead Bar for alignment during shipment D Branding scale and appearance at supplier discretion A 1.0 REF 1.60±0.10 C 1.27±0.10 0.71±0.10 0.71±0.10 5.50±0.10 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com Package Drawing Designator: SJ Type: 4-pin SIP 5.50±0.05 B 8.00±0.05 Branded Face 5.80±0.05 1.70±0.10 A 5.30±0.10 1 6.60±0.10 2 3 4 0.71±0.05 LLLLLLL 0.60±0.10 NNN YYWW +0.06 0.38 –0.04 D 24.65±0.10 Standard Branding Reference View = Supplier emblem L = Lot identifier N = Last three numbers of device part number and optional subtype codes Y = Last two digits of year of manufacture 10.90±0.10 1.0 REF For Reference Only, not for tooling use (reference DWG-9006) Dimensions in millimeters A Dambar removal protrusion (16X) 2.00±0.10 B Metallic protrusion, electrically connected to pin 4 and substrate (both sides) C Thermoplastic Molded Lead Bar for alignment during shipment D Branding scale and appearance at supplier discretion 1.0 REF A 1.60±0.10 1.27±0.10 C 0.71±0.10 0.71±0.10 5.50±0.10 Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000 For the latest version of this document, visit our website: www.allegromicro.com