J-CAPTM Series Highest Joules/cc Conductive Polymer Solid Electrolytic Chip Capacitors FEATURES • Highest Energy per volume • Conductive polymer electrode • Benign failure mode under recommended use conditions • Low ESR • Undertab terminations layout: - High Volumetric Efficiency - Low profile case sizes - High capacitance in smaller dimensions - Close positioning of several parts for efficient high density PCB layout • 3x reflow 260°C compatible LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • Power backup for SSDs (MLC, SLC, EFD, PCIe), battery-powered portable equipment, industrial alarms, smart power meters, and mobile devices. CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L±0.20 (0.008) W+0.20 (0.008) -0.10 (0.004) WP±0.10 (0.004) H max. WN±0.10 (0.004) AP±0.10 (0.004) AN±0.10 (0.004) S Min. L 1210 3528-10 3.50 (0.138) 2.80 (0.110) 1.00 (0.039) 2.50 (0.098) 2.10 (0.083) 1.15 (0.045) 1.35 (0.053) 1.00 (0.039) T 1210 3528-12 3.50 (0.138) 2.80 (0.110) 1.20 (0.047) 2.50 (0.098) 2.10 (0.083) 1.15 (0.045) 1.35 (0.053) 1.00 (0.039) X 2917 7343-15 7.30 (0.287) 4.30 (0.169) 1.50 (0.059) 3.25 (0.128) 3.25 (0.128) 2.00 (0.079) 3.20 (0.126) 2.10 (0.083) 3 2924 7361-15 7.30 (0.287) 6.10 (0.240) 1.50 (0.059) 4.75 (0.187) 4.75 (0.187) 2.00 (0.079) 3.20 (0.126) 2.10 (0.083) 4 2924 7361-20 7.30 (0.287) 6.10 (0.240) 2.00 (0.079) 4.75 (0.187) 4.75 (0.187) 2.00 (0.079) 3.20 (0.126) 2.10 (0.083) W1 dimension applies to the termination width for A dimensional area only. MARKING L, T, X CASE 3, 4 CASE AVX LOGO Polymer Polarity Band (Anode+) MAXIMUM ENERGY PER CASE SIZE AVX LOGO Polymer Capacitance Value in pF 158 = 1500µF 158 J Polarity Band (Anode+) Rated Voltage J = 6.3V XXXXX Capacitance Value in pF 158 = 1500µF 158 J XXXXX ID Code Rated Voltage J = 6.3V ID Code Case Size L T X 3 4 Approved (mJ) 4.7 4.7 18.2 19.6 46.6 Polarity Band (Anode+) W L W H WP HOW TO ORDER TCN 4 Type 061316 Case Size See table above AP S AN WN 158 M 006 R 0055 Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Tolerance M = ±20% Rated DC Voltage 006 = 6.3Vdc 016 = 16Vdc 025 = 25Vdc 035 = 35Vdc 050 = 50Vdc Packaging R = Pure Tin 7" Reel ESR in mΩ 123 J-CAPTM Series Highest Joules/cc Conductive Polymer Solid Electrolytic Chip Capacitors TECHNICAL SPECIFICATIONS Technical Data: Capacitance Range: Capacitance Tolerance: Leakage Current DCL: Rated Voltage (VR) Surge Voltage (VS) Temperature Range: Reliability: ⱕ +85ºC: ⱕ +85ºC: All technical data relate to an ambient temperature of +25°C 4.7 μF to 1500 μF ±20% 0.1CV 6.3 16 25 35 50 8 21 33 46 65 -55°C to +105°C 1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance 60% confidence level NOTE: Conductive Polymer Capacitors are designed to operate within the limits of the environmental conditions specified for each series. If operated continuously at their maximum temperature and / or humidity limit, or beyond these limits, capacitors may exhibit a parametric shift in capacitance and increases in ESR. These changes may occur earlier if the specified environmental conditions are exceeded. Similarly, their normal operational time period will be significantly extended if their general duty cycle includes operation below maximum temperature within humidity controlled environments. Careful attention should be paid to maximum temperature with associated high humidity environments as well as voltage derating, ripple current and current surges. Please reference the AVX Conductive Polymer Capacitor Guidelines for more information or contact factory for application assistance. CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage DC to 85°C, [mJ] μF 4.7 10 22 33 47 Code 475 106 226 336 476 6.3V (J) 16V (C) 100 107 L(200) [1.2] 150 220 330 470 157 227 337 477 L(200)/T(200) T(200) [1.7] [2.6] [5.4] 1000 108 1500 158 X(50) 3(100) X(200)/4(55) 4(55) 25V (E) L(200)/T(200) [3.3] L(250)/T(150,200) [4.7] X(100) 4(70) 4(70) [14.9] [21.8] [32.7] T(200) T(250)* X(100) 3(70) 4(100) 4(70) 35V (V) L(300)/T(200) [1.8] T(200) [3.9] [4.3] [6.5] [9.2] X(100) [18.2] [19.6] 4(100) [38.8] [29.3] [11.6] [17.4] Available Ratings, (ESR ratings in mOhms in brackets) [Energy in mJ] Engineering samples - please contact manufacturer *Codes under development - subject to change Note: Voltage ratings are minimum values. AVX reserves the right to supply higher ratings in the same case size, to the same reliability standards. 124 061316 J-CAPTM Series Highest Joules/cc Conductive Polymer Solid Electrolytic Chip Capacitors RATINGS & PART NUMBER REFERENCE Maximum Case Capacitance Rated Operating Voltage Size (μF) Temperature (V) (ºC) AVX Part No. TCNL107M006#0200 TCNL157M006#0200 TCNT157M006#0200 TCNT227M006#0200 TCNX477M006#0050 TCNX108M006#0200 TCN3108M006#0100 TCN4108M006#0055 TCN4158M006#0055 L L T T X X 3 4 4 100 150 150 220 470 1000 1000 1000 1500 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 105 105 105 85 85 85 105 85 85 TCNL336M016#0200 TCNT336M016#0200 TCNL476M016#0250 TCNT476M016#0150 TCNT476M016#0200 TCNX157M016#0100 TCN4227M016#0070 TCN4337M016#0070 L T L T T X 4 4 33 33 47 47 47 150 220 330 16 16 16 16 16 16 16 16 85 85 85 85 85 85 105 105 TCNT226M025#0200 TCNX476M025#0100 TCN3107M025#0070 TCN4107M025#0100 TCN4157M025#0070 T X 3 4 4 22 47 100 100 150 25 25 25 25 25 105 105 105 105 105 TCNL475M035#0300 TCNT475M035#0200 TCNT106M035#0200 TCNX476M035#0100 TCN4107M035#0100 L T T X 4 4.7 4.7 10 47 100 35 35 35 35 35 105 85 85 105 105 DCL Max. (μA) DF Max. (%) 6.3 Volt @ 85°C 60 10 90 10 90 10 132 10 282 10 600 30 600 20 600 20 900 20 16 Volt @ 85°C 52.8 6 52.8 6 75.2 6 75.2 6 75.2 6 240 6 352 20 528 20 25 Volt @ 85°C 55 6 117.5 6 250 6 250 6 375 6 35 Volt @ 85°C 16.5 6 16.5 10 35 10 165 10 350 10 ESR Max. @ 100kHz (mΩ) MSL Product Category Energy (mJ) ENERGY Energy/volume (mJ/cm3) Energy/area (mJ/cm2) 200 200 200 200 50 200 100 55 55 3 3 3 3 3 3 4 4 4 3 3 3 5 5 5 3 5 5 1.2 1.7 1.7 2.6 5.4 11.6 11.6 11.6 17.4 118 177 147 216 115 246 176 132 198 11.8 17.7 17.7 26.0 17.3 36.9 26.4 26.4 39.6 200 200 250 150 200 100 70 70 3 3 3 3 3 3 4 4 5 5 5 5 5 5 2 3 3.3 3.3 4.7 4.7 4.7 14.9 21.8 32.7 334 277 476 395 395 316 249 374 33.4 33.4 47.6 47.6 47.6 47.4 49.8 74.7 200 100 70 100 70 3 3 4 4 4 3 2 2 2 2 4.3 9.2 19.6 19.6 29.3 364 195 298 219 335 43.9 29.3 44.6 43.9 67.0 300 200 200 100 100 3 3 3 3 4 2 5 5 2 3 1.8 1.8 3.9 18.2 38.8 186 154 328 387 435 18.6 18.6 39.5 58.0 87.1 Energy is calculated by this formula (consider derating factor): Energy = ½ C x ((Vr x X)2 – Vx2) where C = Capacitance Vr = Rated Voltage X = Recommended derating factor Vx= 3V (invariable) Moisture Sensitivity Level (MSL) is defined according to J-STD-020. All technical data relates to an ambient temperature of +25ºC. Capacitance is measured at 120Hz, 0.5RMS with DC bias of 2.2 volts. DCL is measured at rated voltage after 5 minutes. ESR allowed to move up to 1.25 times catalog limit post mounting. For typical weight and composition see page 223. NOTE: AVX reserves the right to supply a higher voltage rating in the same case size, to the same reliability standards. RECOMMENDED DERATING FACTOR Voltage and temperature derating as percentage of Vr Product Category 2 Product Category 3 Product Category 5 100% 100% 100% 95% 90% 85% 80% 75% 70% Rated Voltage 95% 90% Recommended Application Voltage for Vr ≤ 16V 85% 80% Recommended Application Voltage for Vr ≥ 20V 75% 70% Rated Voltage 95% 90% Recommended Application Voltage for Vr ≤ 16V 85% 80% Recommended Application Voltage for Vr ≥ 20V 75% 70% 65% 65% 65% 60% 60% 60% 55% 55% 55% 50% -55ºC 50% -55ºC 061316 85ºC 105ºC 85ºC 105ºC Rated Voltage Recommended Application Voltage for Vr ≤ 16V Recommended Application Voltage for Vr ≥ 20V 50% -55ºC 85ºC 125 J-CAPTM Series Highest Joules/cc Conductive Polymer Solid Electrolytic Chip Capacitors PRODUCT CATEGORY 2, 3 (TEMPERATURE RANGE -55°C TO +105°C) TEST Endurance Storage Life Humidity Temperature Stability Surge Voltage *Initial Limit Condition Characteristics Determine after application of rated voltage for 2000 +48/-0 hours at 85±2ºC and then leaving 1-2 hours at room temperature. Also determine after application of 105ºC temperature, category voltage for 2000 +48/-0 hours and then leaving 1-2 hours at room temperature. Power supply impedance to be ≤ 0.1Ω/V. 105ºC, 0V, 2000h ΔC/C DF ESR Visual examination DCL ΔC/C Determine after storage without applied voltage at 65±2ºC and 95±2% relative humidity for 500 hours and then recovery 1-2 hours at room temperature. Step 1 2 3 4 5 6 Visual examination DCL Temperature°C +20±2 -55+0/-3 +20±2 +85+3/-0 +105+3/-0 +20±2 Duration(min) 15 15 15 15 15 15 Test temperature: 105ºC+3/0ºC Test voltage: Category voltage at 105ºC Surge voltage: 1.3 x category voltage at 105ºC Series protection resistance 1000±100Ω Discharge resistance: 1000Ω Number of cycles: 1000x Cycle duration: 6 min; 30 sec charge, 5 min 30 sec discharge DF ESR Visual examination DCL ΔC/C DF ESR DCL ΔC/C DF no visible damage 1.25 x initial limit within +10/-20% of initial value for Vr ≤ 16V within ±20% of initial value for Vr ≥ 20V 1.5 x initial limit 2 x initial limit no visible damage 1.25 x initial limit within +10/-20% of initial value for Vr ≤ 16V within ±20% of initial value for Vr ≥ 20V 1.5 x initial limit 2 x initial limit no visible damage 3 x initial limit within +30/-20% of initial value 1.5 x initial limit 2 x initial limit +20ºC -55ºC IL* n/a n/a +0/-20% IL* 1.5 x IL* +20ºC +85ºC +105ºC +20ºC IL* 10 x IL* 12.5 x IL* IL* ±5% +20/-0% +30/-0% ±5% IL* 1.5 x IL* 2 x IL* IL* Visual examination no visible damage DCL initial limit ΔC/C within +10/-20% of initial value for Vr ≤ 16V within +20/-30% of initial value for Vr ≥ 20V DF 1.25 x initial limit Initial measurement max. 1hr after the removal from dry pack or after pretreatment at 85°C for 24 hours. PRODUCT CATEGORY 5 (TEMPERATURE RANGE -55°C TO +85°C) TEST Endurance Storage Life Humidity Temperature Stability Surge Voltage *Initial Limit 126 Condition Characteristics Determine after application of rated voltage for 2000 +48/-0 hours at 85±2ºC and then leaving 1-2 hours at room temperature. Power supply impedance to be ≤0.1Ω/V. 85ºC, 0V, 2000h Temperature°C +20±2 -55+0/-3 +20±2 +85+3/-0 +20±2 ΔC/C DF ESR Visual examination DCL ΔC/C Determine after storage without applied voltage at 65±2ºC and 95±2% relative humidity for 500 hours and then recovery 1-2 hours at room temperature. Step 1 2 3 4 5 Visual examination DCL Duration(min) 15 15 15 15 15 Test temperature: 85+3/0ºC Test voltage: Rated voltage Surge voltage: 1.3 x rated voltage Series protection resistance 1000±100Ω. Discharge resistance: 1000Ω Number of cycles: 1000x Cycle duration: 6 min; 30 sec charge, 5 min 30 sec discharge DF ESR Visual examination DCL ΔC/C DF ESR DCL ΔC/C DF Visual examination no visible damage 1.25 x initial limit within +10/-20% of initial value for Vr ≤ 16V within ±20% of initial value for Vr ≥ 20V 1.5 x initial limit 2 x initial limit no visible damage 1.25 x initial limit within +10/-20% of initial value for Vr ≤ 16V within ±20% of initial value for Vr ≥ 20V 1.5 x initial limit 2 x initial limit no visible damage 5 x initial limit within +40/-20% of initial value 1.5 x initial limit 2 x initial limit +20ºC -55ºC +20ºC +85ºC +20ºC IL* n/a IL* 10 x IL* IL* n/a +0/-20% ±5% +20/-0% ±5% IL* 1.5 x IL* IL* 1.5 x IL* IL* no visible damage DCL initial limit ΔC/C within +10/-20% of initial value for Vr ≤ 16V within +20/-30% of initial value for Vr ≥ 20V DF 1.25 x initial limit Initial measurement max. 1hr after the removal from dry pack or after pretreatment at 85°C for 24 hours. 061316