TCM Series Datasheet

TCM Series
Conductive Polymer Solid Electrolytic Chip Multianode Capacitors
FEATURES
• Conductive polymer electrode, multianode design
• Benign failure mode under recommended use
conditions
• Extremely Low ESR
• 3x reflow 260°C compatible
• Volumetric efficiency
• High frequency capacitance retention
LEAD-FREE COMPATIBLE
COMPONENT
Elektra Award 2010
APPLICATIONS
• Telecommunication routers
• Basestations with high power DC/DCs
CASE DIMENSIONS: millimeters (inches)
MARKING
E, V CASE
Code
AVX LOGO
Polymer
Polarity
Band
(Anode+)
Capacitance Value in pF
156 = 15µF
V
156 J
XXXXX
Case Size
See table
above
EIA
Metric
7343-43
7361-38
Rated Voltage
J = 6.3V
L±0.20
W+0.20 (0.008)
(0.008)
-0.10 (0.004)
7.30 (0.287)
4.30 (0.169)
7.30 (0.287)
6.10 (0.240)
H+0.20 (0.008)
-0.10 (0.004)
4.10 (0.162)
3.55 (0.140)
W1±0.20
(0.008)
2.40 (0.094)
3.10 (0.120)
A+0.30 (0.012)
S Min.
-0.20 (0.008)
1.30 (0.051)
4.40 (0.173)
1.30 (0.051)
4.40 (0.173)
W1 dimension applies to the termination width for A dimensional area only.
ID Code
HOW TO ORDER
TCM
E
Type
E
EIA
Code
2917
2924
108
M
004
Capacitance Code
pF code: 1st two digits
represent significant figures,
3rd digit represents multiplier
(number of zeros to follow)
Tolerance
M=±20%
Rated DC Voltage
002=2.5Vdc
004=4Vdc
006=6.3Vdc
010=10Vdc
035=35Vdc
100=100Vdc
R
Packaging
R = Pure Tin 7" Reel
S = Pure Tin 13" Reel
0010
ESR in mΩ
TECHNICAL SPECIFICATIONS
Technical Data:
Capacitance Range:
Capacitance Tolerance:
Leakage Current DCL:
Rated Voltage (VR)
Category Voltage (VC)
Surge Voltage (VS)
Surge Voltage (VS)
Temperature Range:
Reliability:
+85°C:
+105°C:
+85°C:
+105°C:
All technical data relate to an ambient temperature of +25°C
10 μF to 1000 μF
±20%
0.1CV
2.5
4
6.3
10
35
100
2
3.2
5
8
28
80
3.3
5.2
8
13
46
130
2.5
4
6
10
35
100
-55ºC to +105ºC
1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance, 60% confidence level
NOTE: Conductive Polymer Capacitors are designed to operate within the limits of the environmental conditions specified for each series. If operated continuously
at their maximum temperature and / or humidity limit, or beyond these limits, capacitors may exhibit a parametric shift in capacitance and increases in ESR. These
changes may occur earlier if the specified environmental conditions are exceeded. Similarly, their normal operational time period will be significantly extended if their
general duty cycle includes operation below maximum temperature within humidity controlled environments. Careful attention should be paid to maximum temperature with associated high humidity environments as well as voltage derating, ripple current and current surges. Please reference the AVX Conductive Polymer
Capacitor Guidelines for more information or contact factory for application assistance.
116
022416
TCM Series
Conductive Polymer Solid Electrolytic Chip Multianode Capacitors
CAPACITANCE AND RATED VOLTAGE RANGE
(LETTER DENOTES CASE SIZE)
Capacitance
μF
Code
10
106
22
226
33
336
47
476
68
686
100
107
150
157
220
227
330
337
470
477
680
687
1000
108
2.5V (e)
Rated Voltage DC (VR) to 85°C
6.3V (J)
10V (A)
4V (G)
35V (V)
100V (A)
V(50)
E(25)
E(10,15)
E(7,10)
E(12)
E(6,10)
E(6,8,10,12)
Available Ratings, (ESR ratings in mOhms in brackets)
Engineering samples - please contact manufacturer
Note: Voltage ratings are minimum values. AVX reserves the right to supply higher ratings in the same case size, to the same reliability standards.
RATINGS & PART NUMBER REFERENCE
AVX
Part No.
Case Capacitance
Size
(μF)
Rated
Voltage
(V)
TCME108M002#0006
TCME108M002#0010
E
E
1000
1000
2.5
2.5
TCME108M004#0006
TCME108M004#0008
TCME108M004#0010
TCME108M004#0012
E
E
E
E
1000
1000
1000
1000
4
4
4
4
TCME477M006#0007
TCME477M006#0010
TCME687M006#0012
E
E
E
470
470
680
6.3
6.3
6.3
TCME337M010#0010
TCME337M010#0015
E
E
330
330
10
10
TCME226M035#0025
E
22
35
TCMV106M100#0050
V
10
100
Maximum
Operating
Temperature
(ºC)
DCL
Max.
(μA)
2.5 Volt @ 85°C
105
250
105
250
4 Volt @ 85°C
105
400
105
400
105
400
105
400
6.3 Volt @ 85°C
105
296
105
296
105
408
10 Volt @ 85°C
105
330
105
330
35 Volt @ 85°C
105
77
100 Volt @ 85°C
105
100
Moisture Sensitivity Level (MSL) is defined according to J-STD-020.
All technical data relates to an ambient temperature of +25ºC. Capacitance and
DF are measured at 120Hz, 0.5RMS with DC bias of 2.2 volts. DCL is measured
at rated voltage after 5 minutes.
ESR allowed to move up to 1.25 times catalog limit post mounting.
For typical weight and composition see page 223.
NOTE: AVX reserves the right to supply a higher voltage rating or tighter
tolerance part in the same case size, to the same reliability
standards.
DF
Max.
(%)
ESR
Max.
@ 100kHz
(mΩ)
MSL
10
10
6
10
8
8
8
8
100kHz RMS Current (mA)
45ºC
85ºC
105ºC
3
3
8300
6400
5800
4500
3700
2900
6
8
10
12
3
3
3
3
8300
7200
6400
5800
5800
5000
4500
4100
3700
3200
2900
2600
10
10
8
7
10
12
3
3
3
7700
6400
5800
5400
4500
4100
3500
2900
2600
8
8
10
15
3
3
6400
5200
4500
3600
2900
2300
8
25
3
4000
2800
1800
8
50
3
2900
2000
1300
RECOMMENDED DERATING FACTOR
Voltage and temperature derating as percentage of Vr
100%
95%
90%
85%
80%
75%
70%
Rated Voltage
Recommended Application
Voltage for Vr ≤ 10V
Recommended Application
Voltage for Vr ≥ 16V
65%
80%
72%
64%
60%
55%
50%
-55ºC
022416
85ºC
105ºC
117
TCM Series
Conductive Polymer Solid Electrolytic Chip Multianode Capacitors
PRODUCT CATEGORY 105°C
TEST
Condition
Endurance
Determine after application of rated voltage for 2000
+48/-0 hours at 85±2ºC and then leaving 1-2 hours at
room temperature. Also determine after application of
105ºC temperature, category voltage for 2000 +48/-0
hours and then leaving 1-2 hours at room temperature. Power supply impedance to be ≤0.1Ω/V.
Storage Life
Humidity
Temperature
Stability
Surge
Voltage
*Initial Limit
118
105ºC, 0V, 2000h
Determine after storage without applied voltage
at 65±2ºC and 95±2% relative humidity for 500
hours and then recovery 1-2 hours at room
temperature.
Step
1
2
3
4
5
6
Temperature°C
+20±2
-55+0/-3
+20±2
+85+3/-0
+105+3/-0
+20±2
Duration(min)
15
15
15
15
15
15
Test temperature: 105ºC+3/0ºC
Test voltage: Category voltage at 105ºC
Surge voltage: 1.3 x category voltage at 105ºC
Series protection resistance 1000±100Ω
Discharge resistance: 1000Ω
Number of cycles: 1000x
Cycle duration: 6 min; 30 sec charge,
5 min 30 sec discharge
Visual examination
DCL
ΔC/C
DF
ESR
Visual examination
DCL (VR ≤ 75V)
DCL (VR > 75V)
ΔC/C
DF
ESR
Visual examination
DCL
ΔC/C
DF
ESR
DCL
ΔC/C
DF
Characteristics
no visible damage
1.25 x initial limit
within ±20% of initial value
1.5 x initial limit
2 x initial limit
no visible damage
1.25 x initial limit
2 x initial limit
within ±20% of initial value
1.5 x initial limit
2 x initial limit
no visible damage
3 x initial limit
within +30/-20% of initial value
1.5 x initial limit
2 x initial limit
+20ºC -55ºC
IL*
n/a
n/a +0/-20%
IL* 1.5 x IL*
+20ºC +85ºC +105ºC +20ºC
IL*
10 x IL* 12.5 x IL* IL*
±10% +20/-0% +30/-0% ±10%
IL*
1.5 x IL* 2 x IL*
IL*
Visual examination
no visible damage
DCL
ΔC/C
initial limit
within +10/-20% of initial value for Vr ≤ 10V
within +20/-30% of initial value for Vr ≥ 16V
DF
1.25 x initial limit
Initial measurement max. 1hr after the removal from dry pack or after pretreatment at 85°C for 24 hours.
022416