Application Note 85 August 2000 Low Noise Varactor Biasing with Switching Regulators Vanquishing Villainous Vitiators Vis-à-Vis Vital Varactors Jim Williams and David Beebe INTRODUCTION “hyperabrupt” devices. Response modification is possible, with compromises in performance, particularly with regard to linearity and sensitivity.2 Telecommunication, satellite links and set-top boxes all require tuning a high frequency oscillator. The actual tuning element is a varactor diode, a 2-terminal device that changes capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizing loop, as detailed in Figure 1. A phase locked loop (PLL) compares a divided down representation of the oscillator with a frequency reference. The PLL’s output is level shifted to provide the high voltage necessary to bias the varactor, which closes a feedback loop by voltage tuning the oscillator. This loop forces the voltage controlled oscillator (VCO) to operate at a frequency determined by the frequency reference and the divider’s division ratio. Note 1. Theoretical considerations of varactor diodes are treated in Appendix A, “Zetex Variable Capacitance Diodes,” guest written by Neil Chadderton of Zetex. Note 2. The reader is again referred to Appendix A for in-depth discussion of varactor diodes. 200 DIODE CAPACITANCE (pF) 100 Varactor Biasing Considerations The high voltage bias is required to achieve wide-range varactor operation. Figure 2 shows varactor capacitance vs reverse voltage curves for a family of devices. A 10:1 capacitance shift is available, although a 0.1V to 30V swing is required. The curves shown are characteristic of typical ZC836 ZC835 ZC834 ZC833 ZC832 ZC831 ZC830 10 1 0.1 1 10 REVERSE VOLTAGE, VR (V) 100 AN85 A02b Figure 2. Typical Capacitance Voltage Characteristics for the Zetex ZC830-6 Range. 0.1V to 30V Swing Results in ≈10× Capacitance Shift LOOP COMPENSATION CAPACITOR 5V POWER FREQUENCY REFERENCE 32V POWERED (TYPICAL) PHASE LOCKED LOOP OUTPUT AMPLIFIER LEVEL SHIFT ×10 PLL OUTPUT 0V TO 3V (TYPICAL) FILTER 0V TO 30V OUTPUT OSCILLATOR VARACTOR TUNING DIODE FREQUENCY OUTPUT VOLTAGE CONTROLLED OSCILLATOR (VCO) ÷× AN85 F01 Figure 1. Typical Phase Lock Loop-Based Frequency Synthesizer. Level Shift Furnishes 0V to 30V Bias to VCO Varactor Diode, Although a 32V Supply is Required AN85-1 Application Note 85 The bias voltage requirement has traditionally been met by utilizing existing high voltage rails. The current trend towards low voltage powered systems means the high voltage bias must be locally generated. This implies some form of voltage step-up switching regulator. This is certainly possible, but varactor noise sensitivity complicates design. In particular, the varactor responds to any form of amplitude variation of its bias, resulting in an undesired capacitance shift. Such a shift causes VCO frequency movement, resulting in spurious oscillator outputs. DC and low frequency shifts are removed by PLL loop action, but activity outside the loop’s passband causes undesired outputs. Most applications require spurious oscillator output content to be 80dB or more below the nominal output frequency3. This implies a low noise, high voltage supply, mandating caution in the switching regulator design. Switching regulators are often associated with noisy operation, making a varactor bias application seem hazardous. Careful preparation can eliminate this concern, allowing a practical switching regulator-based approach to varactor biasing. Low Noise Switching Regulator Design In theory, a simple flyback regulator will work, but component choice and attention to layout are critical to achieving low noise. Additionally, component count, size and cost are usually considerations in varactor bias applications. Figure 3 shows a step-up switching regulator that, properly incarnated, permits low noise varactor biasing. The circuit is a simple boost regulator. L1, in L1 10µH 5 1 VIN SW D2 R1* 12.5k FB GND 2 C2 4.7µF 50V C3 0.12µF Note 3. Spurious oscillator outputs are referred to as “spurs” in RF parlance. VOUT VIN L1 C1 D1 1 C2 D2 5 2 3 3 SHUTDOWN 4 R2* 499Ω R2 AN85 F03 *1% METAL FILM RESISTORS C1: TAIYO YUDEN JMK212BJ475MG C2: MURATA GRM235Y5V475Z50 D1: 1N4148 D2: ON SEMICONDUCTOR MBR0540 OR LITE ON/DIODES INC. B0540W L1: MURATA LQH3C100 Figure 3. LT1613-Based Boost Regulator with Appropriate Component Selection and Layout Has Low Noise Characteristics Needed for Varactor Biasing AN85-2 Layout is the most crucial design aspect for obtaining low noise. Figure 4 shows a suggested layout. Ground, VIN and VOUT are distributed in planes, minimizing impedance. The LT1613 GND pin (Pin 2) carries high speed, switched current; its path to the circuit’s power exit should be direct and highly conductive at all frequencies. R2’s return current, to the extent possible, should not mix with Pin 2’s large dynamic currents. C1 and C2 should be located close to Pin 5 and D1 respectively. Their grounded ends VOUT 32V LT1613 SHDN Layout Issues D1 5V C1 4.7µF 6.3V 4 conjunction with the SW pin’s ground-referred switching, provides voltage step-up. D1 and C2 filter the output to DC, D2 clips possible L1 negative excursions and the feedback resistor ratio sets the loop servo point, and hence, the output voltage. C3 tailors loop frequency response, minimizing switching-frequency ripple components at the output. C1 and C2 are specified for low loss dynamic characteristics and the LT®1613’s 1.7MHz switching frequency allows miniature, small value components. This relatively high switching frequency also means that ancillary “downstream” filtering is possible with similarly miniature, small value components. C3 R1 AN85 F04 GROUND Figure 4. Layout Requires Attention to Component Placement and Ground Current Flow Management. Compact Layout Reduces Parasitic Inductance, Radiation and Crosstalk. Grounding Scheme Minimizes Return Current Mixing Application Note 85 should tie directly to the ground plane. L1 has a low impedance path to VIN; its driven end returns directly to LT1613 Pin 1. D1 and D2 should have short, low inductance runs to C2 and Pin 2, respectively; their common connection mating tightly with Pin 1 and L1. Pin 1 has a small area, minimizing radiation. Note that this point is enclosed by planes operating at AC ground, forming a shield. The feedback node (Pin 3) is further shielded from switching radiation, preventing unwanted interaction. Finally, L1 should be oriented so its radiation causes minimal circuit disruption. LT1613 regulator, an amplifier-based level shift and a GHz range VCO. The amplifier is biased by a filtered LT1004 reference to a 12V output, simulating a typical varactor bias point. The LT1613 configuration’s low noise output receives additional filtering via the 100Ω-0.1µF network at the amplifier power pin and by the amplifier’s power supply rejection ratio (PSRR). The RC combination provides a theoretical (unloaded) break below 20kHz; the amplifier’s PSRR benefit is derived from Figure 7. This graph shows PSRR vs frequency for a typical amplifier. There is a steep roll-off beyond 100Hz, although almost 20dB attenuation is available in the MHz region. This implies that the amplifier provides some beneficial filtering of the LT1613’s residual 1.7MHz switching components. Level Shifts The low voltage PLL output (see Figure 1) requires an analog level shift to bias the varactor. Figure 5 shows some alternatives. Figure 5a is an amplifier powered from the LT1613’s 32V output. The feedback ratio sets a gain of 10, resulting in a 0V to 30V output for a 0V to 3V input. Figure 5b is a noninverting common base stage. Gain is less well controlled than in Figure 5a, but overall frequency synthesizer loop action obviates this concern. Figure 5c’s common emitter circuit is similar except that it inverts. A final RC filter section is placed directly at the VCO varactor bias input. Ideally this filter’s break frequency is far removed from the 1.7MHz switching rate for maximum ripple attenuation. In practice, the filter is within the PLL loop, placing restrictions on how much delay it can introduce. A PLL loop bandwidth of 5kHz is usually desirable, dictating a filter point of about 50kHz to ensure closedloop stability. As such, the final RC filter (1.6k-0.002µF) is set at this frequency. It is worth noting that the varactor’s input resistance is quite high—essentially that of a reverse-biased diode—and no filter buffering is required to drive it. Test Circuit Figure 6 combines the above considerations into a realistic test circuit. The 5V powered design is composed of the 32V OPTIONAL FEEDBACK TO PLL OUTPUT AMP 32V 0V TO 3V FROM 5V POWERED PLL + TO VARACTOR VIA RC FILTER 358 TYPE – FROM 5V POWERED PLL 0V TO 3V 10k 2N3904 33k 10k 10k OPTIONAL FEEDBACK TO PLL OUTPUT AMP 32V TO VARACTOR VIA RC FILTER FROM 5V POWERED PLL 0V TO 3V TO VARACTOR VIA RC FILTER 33k 2N3904 33Ω 90k 5V (5a) (5b) AN85 F05 (5c) Figure 5. Level Shift Options Include Op Amp (5a), Noninverting Common Base (5b) and Inverting Common Emitter (5c). Op Amp’s Operating Point is Inherently Stable; 5b and 5c Rely on PLL Closed-Loop Action Unless Optional Feedback is Used AN85-3 Application Note 85 L1 10µH D1 32V 5V 5 1 VIN C1 4.7µF 6.3V D2 R1* 12.5k LT1613 4 C2 4.7µF 50V SW SHDN FB C3 0.12µF 100Ω 3 0.1µF R2* 499Ω GND 2 2.7k +V 10k 5V LT1004 1.2V *1% METAL FILM RESISTORS C1: TAIYO YUDEN JMK212BJ475MG C2: MURATA GRM235Y5V475Z50 D1: 1N4148 D2: MBR0540 OR BO540W L1: MURATA LQH3C100 VCO: MINI-CIRCUITS POS-1400 NOTE: DO NOT USE OTHER SIDE OF 358 DUAL OP AMP. WIRE AS GROUNDED INPUT FOLLOWER. ALTERNATELY, LT1006 MAY BE USED VCO + + 358 TYPE (SEE NOTES) 1µF – VARACTOR BIAS INPUT 1.6k 0.002µF VCO OUTPUT 0.975GHz TO 1.4GHz 0.001µF AN85 F06 90k 10k Figure 6. Noise Test Circuit Includes Step-Up Switching Regulator, Biased Op Amp Level Shift, Filtering Elements and GHz Range VCO. Switching Regulator-Associated L1 is the Only Inductor Required POWER SUPPLY REJECTION RATIO (dB) 120 TA = 25°C 100 80 60 Effects of Poor Measurement Technique 40 20 0 0.1 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M AN85 F07 Figure 7. Typical Op Amp Power Supply Rejection Ratio Degrades with Frequency, Although Nearly 20dB is Available in LT1613’s MHz Switching Range Noise Performance Careful measurements permit verification of circuit noise performance.4 Figure 8 shows about 2mV ripple at the LT1613’s 32V output. Figure 9, taken at the amplifier power pin, shows the effect of the 100Ω-0.1µF filter. Ripple and noise are reduced to about 500µV. Figure 10, recorded at the amplifier output, shows the influence of amplifier PSRR. Ripple and noise are further reduced to AN85-4 about 300µV. The actual ripple component is about 100µV. The final RC filter, located directly at the VCO varactor input, gives about 20dB further attenuation. Figure 11 shows ripple and noise inside 20µV with a ripple component of about 10µV. The above results require good measurement technique. The measurements were taken utilizing a purely coaxial probing environment. Deviations from this regime will produce misleading and unduly pessimistic indications.5 For example, Figure 12 shows a 50% amplitude error over Figure 8, even though it nominally monitors the same point. The difference is that Figure 12 utilizes a 3" probe ground lead instead of Figure 8’s coaxial ground tip adapter. Similarly, Figure 9’s amplifier power pin 500µV measurement degrades to Figure 13’s indicated 2mV representation using the 3" probe ground strap. The same Note 4. See Appendix B, “Preamplifier and Oscilloscope Selection,” for equipment recommendations to make the high sensitivity oscilloscope measurements described in this section. See also Appendix C, “Probing and Connection Techniques for Low Level, Wideband Signal Integrity.” Note 5. Additional discourse along these lines is presented in Appendix C, “Probing and Connection Techniques for Low Level, Wideband Signal Integrity.” See also Reference 2-5. Application Note 85 500µV/DIV AC COUPLED 500µV/DIV AC COUPLED 500ns/DIV 500ns/DIV AN85 F08 Figure 8. LT1613-Based Output Shows 2mVP-P Ripple and Noise AN85 F09 Figure 9. RC Filter at Amplifier’s Power Input Pin Reduces Ripple and Noise to 500µVP-P 10µV/DIV AC COUPLED 500µV/DIV AC COUPLED 500ns/DIV 500ns/DIV AN85 F10 Figure 10. Amplifier Output Shows Additional Filtering Due to Amplifier PSRR. Aberrations Are Inside 300µV 500µV/DIV AC COUPLED AN85 F11 Figure 11. VCO Varactor Bias Input, After 50kHz RC Filter, Displays Less Than 20µV Ripple and Noise. Content Coherent with LT1613’s 1.7MHz Switching is Inside 10µV 500µV/DIV AC COUPLED 500ns/DIV AN85 F12 Figure 12. Improper Probing Technique. 3" Ground Lead Causes 50% Display Error vs Figure 8’s Purely Coaxial Measurement 500ns/DIV AN85 F13 Figure 13. 3" Ground Lead Degrades Figure 9’s 500µV Reading to 2mV AN85-5 Application Note 85 ground strap causes pronounced error in Figure 14’s apparent 2mV amplifier output vs Figure 10’s correct 300µV excursion. Figure 15 shows a 70µV indication at the VCO varactor input using the 3" ground strap. That’s a long way from Figure 11’s 20µV data taken with the coaxial ground tip adapter!6 In Figure 16 the coaxial ground tip adapter is used but the VCO varactor input shows a blizzard of noise compared to Figure 11’s orderly trace. The reason is that a 12" voltmeter lead was connected to the point. Pickup and stray RF act against the node’s finite output impedance, corrupting the measurement. Figure 17, also taken at the VCO input, is better but still shows greater than 50% error. The culprit Note 6. If you don’t think 70µV is a “long way” from 20µV, consider your reaction to a 3.5× income tax reduction. Note 7. The reader is not being requested to indulge wishful thinking. Such a probe is more easily realized than might be supposed. See Appendix C, “Probing and Connection Techniques for Low Level, Wideband Signal Integrity.” 10µV/DIV AC COUPLED 500µV/DIV AC COUPLED 500ns/DIV 500ns/DIV AN85 F14 Figure 14. Probe Ground Strap Causes Erroneous 2mV Indication. Actual Value is Figure 10’s 300µV Reading AN85 F15 Figure 15. Probe Ground Strap Causes 3.5× Readout Error vs Figure 11’s Correctly Measured 20µV 10µV/DIV AC COUPLED 10µV/DIV AC COUPLED 500ns/DIV AN85 F16 Figure 16. Effect of 12" Voltmeter Probe on VCO Varactor Input. Coaxially Connected ‘Scope Probe is in Use. 2.5× Measurement Error Referred to Figure 11 Results AN85-6 here is a second probe, located at the LT1613 VSW pin, used to trigger the oscilloscope. Even with coaxial techniques in use at both probe points, the trigger probe dumps transient currents into the ground plane. This introduces small common mode voltages, resulting in the apparent noise increase. The cure is to trigger the oscilloscope with a noninvasive probe.7 500ns/DIV AN85 F16 Figure 17. Oscilloscope Trigger Channel Probe at LT1613 SW Pin Causes 50% Measurement Error vs Figure 11 Application Note 85 Frequency-Domain Performance Although the varactor bias noise amplitude measurements are critical, it is difficult to correlate them with frequency-domain performance. Varactor bias noise amplitude translates into spurious VCO outputs and that is the measurement of ultimate concern. Although it is possible to view the GHz range VCO on an oscilloscope (Figure 18), this time domain measurement lacks adequate sensitivity to detect spurious activity. A spectrum analyzer is required. Figure 19, a spectral plot of VCO output, shows a center frequency of 1.14GHz, with no apparent spurious activity within the ≈ 90dB measurement noise floor. A marker has been placed at 1.7MHz (3.5 divisions from center), corresponding to the LT1613’s switching frequency. No readily distinguishable activity is apparent at about – 90dBc. Succeeding figures “sanity check” this performance by systematically degrading the circuit and noting results. In Figure 20, the VCO varactor input’s RC filter has been replaced with a direct connection. Now the 1.7MHz spurious outputs are easily seen, about – 62dBc. In Figure 21, a 12" voltmeter lead as been connected to the measurement point, resulting in a 4dB AN85 F18 AN85 F19 Figure 18. GHz Range VCO Output is Viewable on Oscilloscope, But Spurious Activity is Undetectable. Spectral Measurements Are Required AN85 F20 Figure 20. “Sanity Checking” Figure 19’s Results by Replacing RC Filter at VCO Varactor Input with Direct Connection. LT1613 1.7MHz Switching Frequency Related Activity Appears at – 62dBc Figure 19. HP-4396B Spectrum Analyzer Indicates Spurious Outputs at Least –90dBc Referred to 1.14GHz VCO Center Frequency AN85 F21 Figure 21. Similar Measurement Conditions to Previous Figure with 12" Voltmeter Probe Added. “Spurs” Increase by 4dB to – 58dBc AN85-7 Application Note 85 degradation, to about – 58dBc. Figure 22 shows pronounced effects due to poor LT1613 layout (power ground pin routed circuitously, rather than directly, back to input common) and component choice (lossy capacitor substituted for C2). Spurious activity jumps to – 48dBc. In Figure 23 proper layout and components are used, but the varactor bias line has been placed in close proximity to switching inductor L1. Additionally, the bias line and RC filter components have been distanced from the ground plane. The resultant electromagnetic pickup and increase in bias line effective inductance cause 1.7MHz “spurs” at – 54dBc. Additional harmonically related activity, although less severe, is also apparent. Figure 24 indicates favorable results when the bias line and RC filter are restored to their proper orientation. The plot is essentially identical to Figure 19. The lesson here is clear. Layout and measurement practice are at least as important as circuit design. As always, the “hidden schematic” dominates performance.8 Note 8: Charly Gullett of Intel Corporation originated the quoted descriptive, an author favorite. AN85 F22 Figure 22. Deliberate Degradation of LT1613’s Grounding Scheme and Output Capacitor Raise Spurious Outputs to – 48dBc AN85 F22 Figure 23. Results with Varactor Bias Line Deliberately Routed Near LT1613’s Switching Inductor, and RC Filter Components Lifted from Ground Plane. 1.7MHz “Spurs” at –54dBc; Other Harmonically Related Components Also Appear AN85-8 AN85 F24 Figure 24. Varactor Bias Line and RC Filter Replaced in Proper Orientation. Figure 19’s Silence is Restored Application Note 85 REFERENCES 1. Chadderton, Neil, “Zetex Variable Capacitance Diodes,” Application Note 9, Issue 2, January 1996. Zetex Applications Handbook, 1998. Zetex plc. UK. 3. Williams, Jim, “High Speed Amplifier Techniques,” Linear Technology Corporation, Application Note 47, August 1991. 2. Williams, Jim, “A Monolithic Switching Regulator with 100µV Output Noise,” Linear Technology Corporation, Application Note 70, October 1997. 4. Hurlock, Les, “ABCs of Probes,” Tektronix, Inc., 1990 APPENDIX A small change in bias voltage. This is particularly useful in battery powered systems where the available bias voltage is limited. The following section, excerpted with permission from Zetex Application Note 9 (see Reference 1), reviews theoretical considerations of varactor diodes. ZETEX VARIABLE CAPACITANCE DIODES 5. McAbel, W. E., “Probe Measurements,” Tektronix, Inc., 1971. The varactor can be modelled as a variable capacitance (Cjv), in series with a resistance (Rs). (Please refer to Figure A1.) Neil Chadderton, Zetex plc Cjv RS Background The varactor diode is a device that is processed so to capitalise on the properties of the depletion layer of a P-N diode. Under reverse bias, the carriers in each region (holes in the P type and electrons in the N type) move away from the junction, leaving an area that is depleted of carriers. Thus a region that is essentially an insulator has been created, and can be compared to the classic parallel plate capacitor model. The effective width of this depletion region increases with reverse bias, and so the capacitance decreases. Thus the depletion layer effectively creates a voltage dependent junction capacitance, that can be varied between the forward conduction region and the reverse breakdown voltage (typically +0.7V to –35V respectively for the ZC830 and ZC740 series diodes). Different junction profiles can be produced that exhibit different Capacitance-Voltage (C-V) characteristics. The Abrupt junction type of example, shows a small range of capacitance due to its diffusion profile, and as a consequence of this is capable of high Q and low distortion, while the Hyperabrupt variety allows a larger change in capacitance for the same range of reverse bias. So called Hyper-hyperabrupt, or octave tuning variable capacitance diodes show a large change in capacitance for a relatively AN85 A01 Figure A1. Common Model for the Varactor Diode The capacitance, Cjv, is dependent upon the reverse bias voltage, the junction area, and the doping densities of the semiconductor material, and can be described by: Cjv = Cj 0 (1 + Vr/ϕ)N where: Cj0 = Junction capacitance at 0V Cjv = Junction capacitance at applied bias voltage Vr Vr = Applied bias voltage ϕ = Contact potential N = Power law of the junction or slope factor The series resistance exists as a consequence of the remaining undepleted semiconductor resistance, a contribution due to the die substrate, and a small lead and package component, and is foremost in determining the performance of the device under RF conditions. AN85-9 Application Note 85 This follows, as the quality factor, Q, is given by: 1 2πfCjv RS where: Cjv = Junction capacitance at applied bias voltage Vr RS = Series Resistance f = Frequency DIODE CAPACITANCE (pF) Q= 300 10 0.1 1 10 REVERSE VOLTAGE, VR (V) 100 AN85 A02a Figure A2a. Typical Capacitance-Voltage Characteristics for the ZC740-54 Range 200 100 DIODE CAPACITANCE (pF) Important Parameters ZC754 ZC753 ZC752 ZC751 ZC750 ZC749 ZC748 ZC747 ZC746 ZC745 ZC744 ZC743 ZC742 ZC741 ZC740 1 So, to maximise Q, Rs must be minimised. This is achieved by the use of an epitaxial structure so minimising the amount of high resistivity material in series with the junction. Note: Zetex has produced a set of SPICE models to enable designers to simulate their circuits in SPICE, PSPICE and similar simulation packages. The models use a version of the above capacitance equation and so the model parameters may also be of interest for other software packages. Information is also provided to allow inclusion of parasitic elements to the model. These models are available on request, from any Zetex sales office. 100 This section reviews the important characteristics of varactor diodes with particular reference to the Zetex range of variable capacitance diodes. ZC836 ZC835 ZC834 ZC833 ZC832 ZC831 ZC830 10 1 0.1 1 10 REVERSE VOLTAGE, VR (V) 100 AN85 A02b The capacitance ratio, commonly expressed as Cx/Cy (where x and y are bias voltages), is a useful parameter that shows how quickly the capacitance changes with applied bias voltage. So, for an Abrupt junction device, a AN85-10 Figure A2b. Typical Capacitance-Voltage Characteristics for the ZC830-6 Range 200 100 DIODE CAPACITANCE (pF) The characteristic of prime concern to the designer is the Capacitance-Voltage relationship, illustrated by a C-V curve, and expressed at a particular voltage by Cx, where x is the bias voltage. The C-V curve summarises the range of useful capacitance, and also shows the shape of the relationship, which may be relevant when a specific response is required. Figures A2a, A2b and A2c show families of C-V curves for the ZC740-54 (Abrupt), ZC830-6 (Hyperabrupt), and ZC930 (Hyper-hyperabrupt) ranges respectively. Obviously, the choice of device type depends upon the application, but aspects to consider include: the range of frequencies the circuit must operate with, and hence an appropriate capacitance range; the available bias voltage; and the required response. ZC934 10 ZC933 ZC932 ZC931 ZC930 1 1 10 REVERSE VOLTAGE, VR (V) 20 AN85 FA02c Figure A2c. Typical Capacitance-Voltage Characteristics for the ZC930-4 Range Application Note 85 700 TJ = 0°C TO 85°C 600 500 ppm/°C C2/C20 figure of 2.8 may be typical, whereas a C2/C20 ration of 6 may be expected for a Hyperabrupt device. This feature of the Hyperabrupt variety can be particularly important when assessing devices for battery-powered applications, where the bias voltage range may be limited. In this instance, the ZC930 series that feature a better than 2:1 tuning range for a 0 to 6V bias may be of particular interest. 400 300 TYPICAL 200 100 The quality factor, Q, at a particular condition is a useful parameter in assessing the performance of a device with respect to tuned circuits, and the resulting loaded Q. 0 1 100 10 30 REVERSE VOLTAGE, VR (V) AN85 A04a Also of interest, with respect to stability, is the temperature coefficient of capacitance, as capacitance changes with VR, and is shown for the three ranges in Figures A4a, A4b and A4c respectively. 700 TEMP = 25°C TYPICAL 600 RS (mΩ) 500 ZC830 AT 470MHz 400 300 ZC833 AT 300MHz 200 ZC836 AT 150MHz 100 0 1 10 REVERSE VOLTAGE, VR (V) 100 AN85 FA03 Figure A3. Typical RS vs VR Relationship for ZC830 Series Diodes 700 TJ = 0°C TO 100°C 600 500 ppm/°C The specified VR is very important in assessing this parameter, because as well as the C-V dependence as detailed previously, a significant part of the series resistance (RS), is due to the remaining undepleted epitaxial layer, which is also dependant upon VR. This RS-VR relationship is shown in Figure A3 for the ZC830, ZC833 and ZC836 Hyperabrupt devices, measured at frequencies of 470MHz, 300MHz and 150MHz respectively, and also serves to illustrate the excellent performance of Zetex Variable Capacitance Diodes at VHF and UHF. Figure A4a. Temperature Coefficient of Capacitance vs VR for the ZC740 Series 400 300 TYPICAL 200 100 0 1 100 10 30 REVERSE VOLTAGE, VR (V) AN85 A04a Figure A4b. Temperature Coefficient of Capacitance vs VR for the ZC830 Series 1400 TEMPERATURE COEFFICIENT (ppm/°C) Zetex guarantees a minimum Q at test conditions of 50MHz, and a relatively low VR of 3 or 4V, and ranges 100 to 450 depending on device type. TJ = 25°C TO 125°C 1200 1000 800 TYPICAL 600 400 200 0 0.1 1 10 REVERSE VOLTAGE, VR (V) AN85 A04c Figure A4c. Temperature Coefficient of Capacitance vs VR for the ZC930 Series AN85-11 Application Note 85 The reverse breakdown voltage, V(BR) also has a bearing on device selection, as this parameter limits the maximum VR that may be used when biasing for minimum capacitance. Zetex variable capacitance diodes typically possess a V(BR) of 35V. The maximum frequency of operation will depend on the required capacitance and the series resistance (and hence useful Q), that is possessed by a particular device type, but also of consequence are the parasitic components exhibited by the device package. These depend on the size, material and construction of the package. For example, the Zetex SOT-23 package has a typical stray capacitance of 0.08pF, and a total lead inductance of 2.8nH, while the E-line package shows less than 0.2pF and 5nH respectively. These low values allow a wide frequency application, for example, the ZC830 and ZC930 series, configured as series pairs are ideal for low cost microwave designs extending to 2.5GHz and above. APPENDIX B PREAMPLIFIER AND OSCILLOSCOPE SELECTION The low level measurements described require some form of preamplification for the oscilloscope. Current generation oscilloscopes rarely have greater than 2mV/DIV sensitivity, although older instruments offer more capability. Figure B1 lists representative preamplifiers and oscilloscope plug-ins suitable for noise measurement. These units feature wideband, low noise performance. It is particularly significant that many of these instruments are no longer produced. This is in keeping with current instrumentation trends, which emphasize digital signal acquisition as opposed to analog measurement capability. INSTRUMENT TYPE MANUFACTURER Amplifier Hewlett-Packard The monitoring oscilloscope should have adequate bandwidth and exceptional trace clarity. In the latter regard high quality analog oscilloscopes are unmatched. The exceptionally small spot size of these instruments is well-suited to low level noise measurement.1 The digitizing uncertainties and raster scan limitations of DSOs impose display resolution penalties. Many DSO displays will not even register the small levels of switching-based noise. Note 1: In our work we have found Tektronix types 454, 454A, 547 and 556 excellent choices. Their pristine trace presentation is ideal for discerning small signals of interest against a noise floor limited background. MODEL MAXIMUM NUMBER BANDWIDTH SENSITIVITY/GAIN AVAILABILITY COMMENTS 461A 150MHz Gain = 100 Secondary Market Differential Amplifier Preamble 1855 100MHz Gain = 10 Current Production Stand-Alone, Settable Bandstops Differential Amplifier Tektronix 1A7/1A7A 1MHz 10µV/DIV Secondary Market Requires 500 Series Mainframe, Settable Bandstops Differential Amplifier Tektronix 7A22 1MHz 10µV/DIV Secondary Market Requires 7000 Series Mainframe, Settable Bandstops Differential Amplifier Tektronix 5A22 1MHz 10µV/DIV Secondary Market Requires 5000 Series Mainframe, Settable Bandstops Differential Amplifier Tektronix ADA-400A 1MHz 10µV/DIV Current Production Stand-Alone with Optional Power Supply, Settable Bandstops 1822 10MHz Gain = 1000 Current Production Stand-Alone, Settable Bandstops SR-560 1MHz Gain = 50000 Current Production Stand-Alone, Settable Bandstops, Battery or Line Operation Differential Amplifier Preamble Differential Amplifier Stanford Research Systems 50Ω Input, Stand-Alone Figure B1. Some Applicable High Sensitivity, Low Noise Amplifiers. Trade-Offs Include Bandwidth, Sensitivity and Availability AN85-12 Application Note 85 APPENDIX C PROBING AND CONNECTION TECHNIQUES FOR LOW LEVEL, WIDEBAND SIGNAL INTEGRITY1 The most carefully prepared breadboard cannot fulfill its mission if signal connections introduce distortion. Connections to the circuit are crucial for accurate information extraction. The low level, wideband measurements demand care in routing signals to test instrumentation. Pickup Ground Loops Poor Probing Technique Figure C1 shows the effects of a ground loop between pieces of line-powered test equipment. Small current flow between test equipment’s nominally grounded chassis creates 60Hz modulation in the measured circuit output. This problem can be avoided by grounding all line powered test equipment at the same outlet strip or otherwise ensuring that all chassis are at the same ground potential. Similarly, any test arrangement that permits circuit current flow in chassis interconnects must be avoided. Figure C3’s photograph shows a short ground strap affixed to a scope probe. The probe connects to a point which provides a trigger signal for the oscilloscope. Circuit output noise is monitored on the oscilloscope via the coaxial cable shown in the photo. 100µV/DIV Figure C2 also shows 60Hz modulation of the noise measurement. In this case, a 4-inch voltmeter probe at the feedback input is the culprit. Minimize the number of test connections to the circuit and keep leads short. Note 1: Veterans of LTC Application Notes, a hardened crew, will recognize this Appendix from AN70 (see Reference 2). Although that publication concerned considerably more wideband noise measurement, the material is directly applicable to this effort. As such, it is reproduced here for reader convenience. 500µV/DIV 2ms/DIV AN85 C01 Figure C1. Ground Loop Between Pieces of Test Equipment Induces 60Hz Display Modulation 5ms/DIV AN85 C02 Figure C2. 60Hz Pickup Due to Excessive Probe Length at Feedback Node AN85-13 Figure C3. Poor Probing Technique. Trigger Probe Ground Lead Can Cause Ground Loop-Induced Artifacts to Appear in Display Application Note 85 AN85-14 Application Note 85 Figure C4 shows results. A ground loop on the board between the probe ground strap and the ground referred cable shield causes apparent excessive ripple in the display. Minimize the number of test connections to the circuit and avoid ground loops. Figure C10’s trace shows this to be true. The former example’s aberrations and excessive noise have disappeared. The switching residuals are now faintly outlined in the amplifier noise floor. Maintain coaxial connections in the noise signal monitoring path. Violating Coaxial Signal Transmission—Felony Case Direct Connection Path In Figure C5, the coaxial cable used to transmit the circuit output noise to the amplifier-oscilloscope has been replaced with a probe. A short ground strap is employed as the probe’s return. The error inducing trigger channel probe in the previous case has been eliminated; the ’scope is triggered by a noninvasive, isolated probe.2 Figure C6 shows excessive display noise due to breakup of the coaxial signal environment. The probe’s ground strap violates coaxial transmission and the signal is corrupted by RF. Maintain coaxial connections in the noise signal monitoring path. A good way to verify there are no cable-based errors is to eliminate the cable. Figure C11’s approach eliminates all cable between breadboard, amplifier and oscilloscope. Figure C12’s presentation is indistinguishable from Figure C10, indicating no cable-introduced infidelity. When results seem optimal, design an experiment to test them. When results seem poor, design an experiment to test them. When results are as expected, design an experiment to test them. When results are unexpected, design an experiment to test them. Test Lead Connections Violating Coaxial Signal Transmission— Misdemeanor Case Figure C7’s probe connection also violates coaxial signal flow, but to a less offensive extent. The probe’s ground strap is eliminated, replaced by a tip grounding attachment. Figure C8 shows better results over the preceding case, although signal corruption is still evident. Maintain coaxial connections in the noise signal monitoring path. Proper Coaxial Connection Path In Figure C9, a coaxial cable transmits the noise signal to the amplifier-oscilloscope combination. In theory, this affords the highest integrity cable signal transmission. In theory, attaching a voltmeter lead to the regulator’s output should not introduce noise. Figure C13’s increased noise reading contradicts the theory. The regulator’s output impedance, albeit low, is not zero, especially as frequency scales up. The RF noise injected by the test lead works against the finite output impedance, producing the 200µV of noise indicated in the figure. If a voltmeter lead must be connected to the output during testing, it should be done through a 10kΩ-10µF filter. Such a network eliminates Figure C13’s problem while introducing minimal error in the monitoring DVM. Minimize the number of test lead connections to the circuit while checking noise. Prevent test leads from injecting RF into the test circuit. Note 2: To be discussed. Read on. 100µV/DIV 5µs/DIV AN85 C04 Figure C4. Apparent Excessive Ripple Results from Figure C3’s Probe Misuse. Ground Loop on Board Introduces Serious Measurement Error AN85-15 Application Note 85 Figure C5. Floating Trigger Probe Eliminates Ground Loop, But Output Probe Ground Lead (Photo Upper Right) Violates Coaxial Signal Transmission 500µV/DIV 5µs/DIV AN85 C06 Figure C6. Signal Corruption Due to Figure C5’s Noncoaxial Probe Connection AN85-16 Application Note 85 Figure C7. Probe with Tip Grounding Attachment Approximates Coaxial Connection 100µV/DIV 5µs/DIV AN85 C08 Figure C8. Probe with Tip Grounding Attachment Improves Results. Some Corruption is Still Evident AN85-17 Application Note 85 Figure C9. Coaxial Connection Theoretically Affords Highest Fidelity Signal Transmission 100µV/DIV 5µs/DIV AN85 C10 Figure C10. Life Agrees with Theory. Coaxial Signal Transmission Maintains Signal Integrity. Switching Residuals Are Faintly Outlined in Amplifier Noise AN85-18 Application Note 85 Figure C11. Direct Connection to Equipment Eliminates Possible Cable-Termination Parasitics, Providing Best Possible Signal Transmission 100µV/DIV 5µs/DIV AN85 C12 Figure C12. Direct Connection to Equipment Provides Identical Results to Cable-Termination Approach. Cable and Termination Are Therefore Acceptable AN85-19 Application Note 85 200µV/DIV 5µs/DIV AN85 C13 Figure C13. Voltmeter Lead Attached to Regulator Output Introduces RF Pickup, Multiplying apparent Noise Floor Isolated Trigger Probe The text associated with Figure C5 somewhat cryptically alluded to an “isolated trigger probe.” Figure C14 reveals this to be simply an RF choke terminated against ringing. The choke picks up residual radiated field, generating an isolated trigger signal. This arrangement furnishes a ’scope trigger signal with essentially no measurement corruption. The probe’s physical form appears in Figure C15. For good results, the termination should be adjusted for minimum ringing while preserving the highest possible amplitude output. Light compensatory damping produces Figure C16’s output, which will cause poor ’scope triggering. Proper adjustment results in a more favorable output (Figure C17), characterized by minimal ringing and welldefined edges. Trigger Probe Amplifier The field around the switching magnetics is small and may not be adequate to reliably trigger some oscilloscopes. In such cases, Figure C18’s trigger probe amplifier is useful. It uses an adaptive triggering scheme to compensate for variations in probe output amplitude. A stable 5V trigger output is maintained over a 50:1 probe output range. A1, operating at a gain of 100, provides wideband AC gain. The output of this stage biases a 2-way peak detector (Q1 through Q4). The maximum peak is stored in Q2’s emitter capacitor, while the minimum excursion is retained in Q4’s emitter capacitor. The DC value of the midpoint of A1’s AN85-20 output signal appears at the junction of the 500pF capacitor and the 3MΩ units. This point always sits midway between the signal’s excursions, regardless of absolute amplitude. This signal-adaptive voltage is buffered by A2 to set the trigger voltage at the LT1394’s positive input. The LT1394’s negative input is biased directly from A1’s output. The LT1394’s output, the circuit’s trigger output, is unaffected by >50:1 signal amplitude variations. An X100 analog output is available at A1. Figure C19 shows the circuit’s digital output (Trace B) responding to the amplified probe signal at A1 (Trace A). Figure C20 is a typical noise testing setup. It includes the breadboard, trigger probe, amplifier, oscilloscope and coaxial components. L1 PROBE SHIELDED CABLE BNC CONNECTION TO TERMINATION BOX L1: J.W. MILLER #100267 TERMINATION BOX 1k DAMPING ADJUST 4700pF BNC OUTPUT AN70 FC14 Figure C14. Simple Trigger Probe Eliminates Board Level Ground Loops. Termination Box Components Damp L1’s Ringing Response Figure C15. The Trigger Probe and Termination Box. Clip Lead Facilitates Mounting Probe, Is Electrically Neutral Application Note 85 AN85-21 Application Note 85 10mV/DIV 10mV/DIV 10µs/DIV 10µs/DIV AN85 C16 Figure C16. Misadjusted Termination Causes Inadequate Damping. Unstable Oscilloscope Triggering May Result AN85 C17 Figure C17. Properly Adjusted Termination Minimizes Ringing with Small Amplitude Penalty 50Ω ANALOG BNC OUTPUT TO ’SCOPE TRIGGER INPUT 5V 2k 3 Q1 6 Q2 2 5V 4 + 3M 500pF 0.005µF A1 LT1227 5V + 0.005µF – 2k 5 1 – 750Ω 13 1k 15 10Ω 3M 10 14 Q3 5V 12 A2 LT1006 Q4 11 470Ω + + 10µF 0.1µF 100µF 0.1µF + 2k 0.1µF 470Ω Q1, Q2, Q3, Q4 = CA3096 ARRAY: TIE SUBSTRATE (PIN 16) TO GROUND = 1N4148 TRIGGER PROBE AND TERMINATION BOX (SEE FIGURE C14 FOR DETAILS) Figure C18. Trigger Probe Amplifier Has Analog and Digital Outputs. Adaptive Threshold Maintains Digital Output Over 50:1 Probe Signal Variations A = 1V/DIV AC COUPLED B = 5V/DIV 10µs/DIV (UNCALIB) AN85 C19 Figure C19. Trigger Probe Amplifier Analog (Trace A) and Digital (Trace B) Outputs AN85-22 – LT1394 DIGITAL TRIGGER OUT BNC TO ’SCOPE AN85 C18 Figure C20. Typical Noise Test Setup Includes Trigger Probe, Amplifier, Oscilloscope and Coaxial Components Application Note 85 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. AN85-23 Application Note 85 AN85-24 Linear Technology Corporation an85f LT/TP 0800 4K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com LINEAR TECHNOLOGY CORPORATION 2000