V07N3 - AUGUST

LINEAR TECHNOLOGY
AUGUST 1997
IN THIS ISSUE…
COVER ARTICLE
The LT®1533 Heralds a New Class
of Low Noise Switching Regulators
.................................................. 1
Jeff Witt
Issue Highlights ........................2
VOLUME VII NUMBER 3
The LT1533 Heralds a
New Class of Low Noise
Switching Regulators
by Jeff Witt
LTC in the News ......................... 2
DESIGN FEATURES
The LTC®1067 and LTC1067-50:
Universal 4th Order Low Noise,
Rail-to-Rail Switched Capacitor
Filters ........................................6
Doug La Porte
LTC1422: Simple and Versatile
Hot Swap™ Solution ................11
David Soo
LTC1626 Low Voltage Monolithic
Step-Down Converter Operates
from a Single Li-Ion Cell ..........15
Tim Skovmand
LTC1340 Varactor Driver Saves
Power in Cellular Phones .........18
Dave Bell
DESIGN IDEAS
LT1635 1A Shunt Charger .......22
Mitchell Lee
Negative-to-Positive
Telecommunication Supply ..... 23
Kurk Mathews
Send Camera Power and Video
on the Same Coax Cable ..........24
Frank Cox
MUX the LTC1419
Without Software .................... 25
Kevin R. Hoskins
(More Design Ideas on pages 26–30;
complete list on page 22)
DESIGN INFORMATION
Understanding and Applying
Voltage References (Part Two)
................................................31
Mitchell Lee
New Device Cameos ..................37
Design Tools ............................39
Sales Offices ............................40
Every designer approaches switching
power supplies with trepidation or
dread—these circuits are infamous
as generators of noise or electromagnetic interference (EMI). However,
switching regulators are indispensable when systems require small size,
high efficiency, battery-powered
operation or isolated power. Modern
analog systems combine these
requirements with demands for ever
increasing performance; RF communications devices are becoming more
sensitive and analog-to-digital
converters are pushing analog measurements to greater resolution and
bandwidth. Such systems cannot tolerate interference from any source.
Noise is Due to
Fast Switches
Ill effects due to ripple voltages and
currents at the operating frequency of
a switching regulator can usually be
eliminated by careful design. Low ESR
capacitors, closed inductors, LC filters and proper trace routing to avoid
ground loops and IR drops will reduce
this noise to acceptable levels.
However, switching regulator EMI
problems are most often the result of
high frequency noise generated by
switching high potentials or currents.
In order to maintain high efficiency,
these transitions are designed to occur
as quickly as possible. These fast
edges will couple capacitively or
inductively to nearby circuitry, and
can radiate energy to nearby or even
remotely placed circuits. The magnitude of such stray coupling and its
potential for causing trouble are difficult to predict. Once discovered,
eliminating these effects requires a
lot of experimenting, numerous layout revisions, expensive shielding,
black art and good luck.
Introducing the LT1533
Low Noise Switcher
The LT1533 is a new switching regulator that provides a solution to EMI
problems through two flexible
approaches. First, the slew rates of
both the current through the power
switch and the voltage on it are easily
programmed with external resistors.
Limiting these slew rates will remove
the highest harmonics from the
switching waveforms. Second, the
LT1533, with two 1A power switches,
is designed to operate in push-pull
circuits. Such circuits, with their low
input and output current ripple, are
inherently quiet. The result is an
integrated switching regulator that
provides very quiet output power and
very low emissions. Figure 1 gives an
example of what can be achieved. The
top trace shows the output of a pushpull boost regulator generating 120mA
at 12V from an input of 5V. This trace
was measured using a 10MΩ
continued on page 3
, LTC and LT are registered trademarks of Linear Technology Corporation. Adaptive Power, Burst Mode, C-Load,
FilterCAD, Hot Swap, LinearView, Micropower SwitcherCAD and SwitcherCAD are trademarks of Linear Technology
Corporation. Other product names may be trademarks of the companies that manufacture the products.
EDITOR’S PAGE
Issue Highlights
Our cover article for this issue introduces the LT1533, a new switching
regulator that provides a solution to
EMI problems through two flexible
approaches. First, the slew rates of
both the current through the power
switch and the voltage on it are easily
programmed with external resistors.
Limiting these slew rates removes the
highest harmonics from the switching waveforms. Second, the LT1533
is designed to operate in push-pull
circuits. Such circuits, with their low
input and output current ripple, are
inherently quiet. The result is an
integrated switching regulator that
provides very quiet output power and
very low emissions.
Another power control device, the
LTC1626 low voltage monolithic
stepdown converter, also debuts in
this issue. The LTC1626 is a monolithic, low voltage, step-down current
mode DC/DC converter with an input
supply voltage range of 2.5V to 6V,
making it ideal for single-cell Li-Ion or
3- to 4-cell NiCd/NiMH applications.
A built-in 0.32Ω (at V IN = 4.5V)
P-channel switch allows up to 0.6A of
output current. The LTC1626 incorporates automatic power saving Burst
Mode™ operation to reduce gatecharge losses when the load current
drops below the level required for
continuous operation. With no load,
the converter draws only 160µA; in
shutdown it draws a mere 1µA—making it ideal for current-sensitive
applications.
Also introduced in this issue is a
specialized power device, the LTC1340
varactor driver. This novel product
neatly fills a “crack” that has appeared in the block diagram of portable
communications equipment—the
need to provide 5V swing to the VCO
control input even though the rest of
the product operates at 3V. The
LTC1340 is a low noise amplifier with
an output that can swing to nearly
twice the supply voltage. A 4MHz onchip charge-pump DC/DC converter
produces the doubled supply voltage
to power the amplifier. The IC, to2
gether with three ceramic capacitors,
consumes a mere 0.065 in2 of PC
board area.
On the filter front, we present the
LTC1067 and LTC1067-50 universal, 4th order switched capacitor filters
designed for rail-to-rail operation.
Each part contains two identical, high
accuracy, very wide dynamic-range
2nd order filter building blocks. Each
building block, together with three to
five resistors, provides 2nd order filter transfer functions, including
lowpass, bandpass, highpass, notch
and allpass. These parts can be used
to easily design 4th order or dual 2nd
order filters. Both parts are double
sampled and can operate on supplies
from ±5V to 3V.
Also included in this issue is a new
Hot Swap™ controller, the LTC1422.
Hot Swap controllers allow circuit
boards to be safely plugged into a live
backplane. Like the LTC1421 Hot
Swap controller, introduced in the
August 1996 issue of Linear Technology, the LTC1422 can handle supply
voltages in the 3V–12V range. The
difference between these two parts is
in the number of supplies that can be
independently controlled: the
LTC1421 is a 3-channel device,
whereas the LTC1422 is a singlechannel device.
This issue features an exceptionally large and varied selection of
Design Ideas. There’s a solar-powered battery charger, 3V to 1.xV, 12V
to 5V and –48V to 5V DC/DC converters, a circuit that allows video from
and power to a surveillance camera to
share the same coax cable, a shortcircuit protected isolated high-side
switch, some novel applications for
the LTC1590 12-bit DAC and a method
for MUXing the LTC1419 14-bit ADC
without software.
This issue also includes the conclusion of the in-depth examination
of voltage reference specifications, begun in the June 1997 issue of Linear
Technology. We conclude with a half
dozen New Device Cameos.
LTC in the News…
Linear Technology Corporation
announced on July 22 that net sales
for its fiscal year ended June 29 were
$379,251,000, a nominal increase over
net sales of the $377,771,000 for the
previous year. The Company also
reported record n e t i n c o m e o f
$134,371,000 for the year, a nominal
increase over last year’s $133,964,000.
Earnings per share decreased nominally from $1.72 in FY’97, as the
increase in net income was offset by an
increase in shares outstanding.
According to Robert Swanson,
president and CEO, “our business
accelerated nicely in the second half of
the year and we concluded the year
attaining record bookings, sales and
net profit. We are going into the new
year with good momentum. We are
even on Mars with several of our products on both the Pathfinder spacecraft
and the Sojourner robot.”
Net sales for the fourth quarter
were $104,075,000, a 16% increase
over the fourth quarter of the previous
year. Net income for the quarter was
$37,402,000 or $0.47 per share, compared with $31,357,000 or $0.40 per
share, an increase of 19% over the
fourth quarter of the previous year.
Sequentially, the results for the fourth
quarter were up 10% as compared to
net sales and net income reported for
the third quarter of $95,033,000 and
$33,980,000 or $0.43 per share.
Linear Technology is increasing its
quarterly dividend from $0.05 to $0.06
per share. Payment will be on August
20, 1997 to shareholders of record on
August 1, 1997.
These impressive financials are one
of the reasons that Linear Technology
has again appeared in the “The Business Week Global 1000,” where
companies are ranked according to their
market value. LTC’s market value was
ranked at 441, ahead of such firms as
Harris, Southwest Airlines and Maxim.
LTC has also been ranked in the “Top
200,” a listing of the leading electronic
companies worldwide, ranked by electronics sales revenue, in the July issue
of Electronic Business Today.
Chicago Corporation analyst David
Wu in New York said of LTC, “The global
markets are improving, orders are up,
and the telecom industry, in which
Linear participates strongly is up. In
the long run, Wu estimates “Linear’s
sales can grow in the area of 25%.”
Linear Technology Magazine • August 1997
DESIGN FEATURES
A Closer Look at the LT1533
The LT1533 is a fixed frequency current mode PWM switching regulator.
Output voltage is regulated by controlling the peak switch current on
each cycle of the oscillator, resulting
in good transient performance and
rapid current limiting. The oscillator
(see the block diagram in Figure 2)
drives a toggle flip-flop, alternately
enabling one of two 0.5Ω NPN power
switches, QA and QB. The switch
current is monitored by a sense resistor at the emitter of the switch. The
output voltage (either positive or negative) is compared with an accurate
internal 1.25V reference voltage by
an error amplifier whose current output, along with loop compensation
components tied to the VC pin, determine the peak switch current required
for regulation; a comparator turns off
the switch when this current level is
reached.
20mV/DIV
200µV/DIV
5µs/DIV
1533_01.eps
Figure 1. Output ripple of an LT1533
switching regulator producing 120mA
at 12V from a 5V input
LT1533, continued from page 1
oscilloscope probe with a six-inch
ground lead, demonstrating that there
is no significant inductively or capacitively coupled noise. Probing the
output of the LT1533 circuit with a
50Ω low noise amplifier reveals the
real performance (second trace): peakto-peak output ripple of the low noise
switcher is only 150µV in a 10kHz to
100MHz bandwidth.
SHDN
VIN
The slew-control circuitry monitors the collector voltages and emitter
currents of the power switches and
adjusts base drive to control both the
voltage and current slew rates. The
desired rates are programmed by tying
the RVSL and RCSL pins to ground with
resistors between 4k and 68k, corresponding to slew rates from ~80V/µs
to 5V/µs and 7A/µs to 0.4 A/µs. This
allows the circuit designer to directly
trade off quiet, low EMI operation
with high efficiency: low slew rates
result in slowly changing stray fields,
which generate less interference, but
increase the conduction losses in the
switches.
The LT1533 oscillator presents
additional opportunities for managing EMI. Its wide frequency range
(20kHz to 250kHz) allows the designer
to avoid sensitive frequencies. Operating frequency is set with a capacitor
PGND
COL A COL B
VC
LDO REGULATOR
NEGATIVE
FEEDBACK AMP
+
QA
QB
INTERNAL VCC
–
100k
NFB
+
OUTPUT
DRIVERS
50k
–
–
FB
+
–
ERROR AMP
+
gm
SLEW CONTROL
RVSL
RCSL
COMPARATOR
+
1.25V
–
S
Q
FF
R
RT
OSCILLATOR
CT
Q
SYNC
T
FF
Bk
GND
Q
1533_02.EPS
DUTY
Figure 2. LT1533 block diagram
Linear Technology Magazine • August 1997
3
DESIGN FEATURES
5V
47µF
6.3V
14
1
VIN
NC
COL A
25nH*
PGND
8
11
4
1
4
1
4
NFB
DUTY
COL B
SHDN
RCSL
SYNC
RVSL
CT
GND RT
9
6
18k
5
VC
FB
L1
300µH
1.2k
16
LT1533
3
D1
T1
2
L2
10µH
12V/200mA
C2
22µF
20V
C1
22µF
20V
220pF
15
12
4k–68k
13
4k–68k
D2
7
21.5k
10
*BEAD OR PCB TRACE
T1 = COILTRONICS CTX02 13666-X1
L1 = COILTRONICS CTX300-2
L2 = COILTRONICS DT1608C-103
D1, D2 = MOTOROLA MBRS1100T3
2.49k
15k
1000pF
1500pF 0.015µF
1533_03.EPS
Figure 3. 5V to 12V push-pull PWM converter
on the CT pin and a resistor of nominally 17k on the RT pin. The LT1533
can also be synchronized to an external clock, allowing accurate placement
of both switching frequency and
phase.
Push-Pull PWM Makes a
Quiet Boost Converter
The push-pull converter in Figure 3
produces 200mA at 12V from an input
of 5V. The oscillator is set to 80kHz
(note that the circuit operates at half
this frequency) and the LT1533
applies a pulse-width modulated 5V
to the primary side of the transformer.
The rectified secondary voltage is filtered by L1 to generate 12V on C1. In
this circuit, L1 is the primary energy
storage device, so the transformer
can be made fairly small. Additional
output filtering is provided by L2 and
C2.
This topology is inherently quiet.
Current through L1 into the primary
output capacitor C1 is a continuous
triangle wave with little high frequency
content, resulting in low conducted
output noise. With an appropriate
transformer turns ratio, RMS input
current is kept low, reducing the
potential for conducted noise on the
input.
It is advantageous to start with a
good topology, but high frequency
noise will still get around via stray
capacitance and mutual inductance;
the best way to deal with this is to
eliminate fast edges. Figure 4 shows
several waveforms from the circuit as
TRACE A
0.5A/DIV
TRACE A
0.5A/DIV
TRACE B
20mV/DIV
TRACE C
500µV/DIV
TRACE B
20mV/DIV
TRACE C
500µV/DIV
0.2µs/DIV
it delivers 120mA of output current.
The upper trace in each photo is the
current in switch QA as it turns off.
Trace B is the output voltage probed
with a 10MΩ scope probe with a sixinch ground lead. The lower trace is
the output measured with a low noise
amplifier. In the left photo the switch
slew rates are programmed to their
highest values with 3.9k resistors on
the RCSL and RVSL pins. The fast switch
transients induce high frequency
ripple on the output (the higher level
of noise on the middle trace is due to
the inductance of the scope probe’s
ground lead). By lowering the slew
rates (RCSL = 24k and RVSL = 8.2k) this
potentially troublesome output ripple
is eliminated, as shown in the right
photo. The efficiency penalty is minor;
the slower slew rates reduce efficiency
from 73% to 70%.
This combination of appropriate
circuit topology and controlled slew
rates produces the exceptionally clean
output shown in Figure 1. This circuit
is simply implemented with ordinary
PCB construction, and can be placed
in close proximity to sensitive circuits
without the need for expensive electrostatic or magnetic shielding.
DC Transformer
with Civilized Edges
Grounding the Duty pin of the LT1533
disables the feedback loop and runs
each switch at 50% duty cycle,
allowing the LT1533’s use in DC transformer circuits. Such circuits are
useful for generating bipolar or isolated supplies; Figure 5 shows an
0.2µs/DIV
1533_04.eps
Figure 4. Lowering the slew rates of the power switches (Trace A) eliminates high frequency ripple at the output (Traces B and C).
4
Linear Technology Magazine • August 1997
DESIGN FEATURES
5V
22µF
10V
14
1
8
VIN
NC
25nH*
LT1533
3
11
4
1
3.3
1
3.3
3
22µF
35V
COL B
RCSL 12
13
R
SHDN
SYNC
68k
4k–68k
VSL
RT
CT
9
6
5
18k
3300pF
VC
1, 2, 7, 8
47k
7
FB
GND
150k
12V
80mA
2.2µF
25V
150k
22µF
35V
5
15
DUTY
1
332k
2
2 × BAT85
16
PGND
LT1121-CS8
T1
2
COL A
NFB
8
4
LT1175-CS8
332k
3
2.2µF
25V
–12V
80mA
4 × 1N5819
10
10k
*BEAD OR PCB TRACE
T11533_05.EPS
= COILTRONICS CTX02 13716-X1
Figure 5. 5V to ±12V DC transformer
3.3V to 5V Boost Converter
example. The LT1533 switches 5V
across a 3.3:1 transformer and a diode
bridge rectifies the secondary side
voltages to produce nominally 16V
bipolar outputs that are regulated to
±12V. Short-circuit current limit at
the output is provided by the LT1533’s
switch current limit; the 1A switch
limit is transformed to 0.3A on the
secondary.
A common problem with isolatedoutput switchers is that fast edges
couple through stray capacitance
between the primary and secondary
VIN
3.3V
windings of the transformer to create
common mode noise on the outputs.
Also, linear regulators are incapable
of rejecting high frequency noise at
their inputs. Both problems are greatly
reduced by limiting the switch slew
rates. Shielding between the windings can be eliminated, reducing
transformer size and cost. LC filters
on the isolated side are unnecessary
with the linear regulators rejecting
ripple at the operating frequency and
the controlled slew rates eliminating
high frequency ripple.
L1
100µH
C2
33µF
10V
1
3
8
11
4
D1
VOUT
5V/350mA
C1
100µF
10V
14
VIN
NC
COL A
COL B
DUTY
NFB
PGND
LT1533
SHDN
RCSL
SYNC
RVSL
FB
GND RT
9
CT
6
2
10Ω
15
*50nH
16
12
4k–68k
13
4k–68k
7.50k
7
VC
5
18k
10
2.49k
10k
1000pF
2200pF
0.01µF
*BEAD OR PCB TRACE
L1 = COILTRONICS CTX100-4
D1 = MOTOROLA MBRS120T3
C1 = AVX TPSD107M010R0100
C2 = AVX TPSC336M010R0375
Figure 6. 3.3V to 5V boost converter
Linear Technology Magazine • August 1997
1533_06.EPS
Simple switching topologies can also
benefit from the LT1533’s low noise
features. In a boost regulator, for
example, the current into the output
capacitor is a square wave, which
contains the high frequency harmonics generated by a fast power switch.
Even when the rectifying diode is off,
fast voltage waveforms at the switch
couple through the Schottky diode’s
capacitance. Fast switching can also
excite high frequency resonant circuits
formed by the diode’s capacitance and
parasitic inductance due to board
traces. All of these effects can be
reduced by controlling the slew rate of
the switch. Figure 6 shows the LT1533
in a simple boost circuit generating
5.0V from a 3.3V input, a typical
requirement when interfacing 3.3V
logic systems to 5V high performance
ADCs. The collectors of the two power
switches are tied together and alternately energize the boost inductor.
Figure 7 shows several waveforms at
two different slew rate settings with
the circuit delivering 200mA of output current. Trace A is the switch
voltage, trace B is the current through
the output capacitor and trace C is
the AC-coupled output voltage in a
100MHz bandwidth. In the left photo,
the slew rates are set to their maximum values (RCSL = RVSL = 3.9kΩ).
The rapidly switched current combined with the finite series inductance
of the output capacitor result in large
continued on page 21
5
DESIGN FEATURES
The LTC1067 and LTC1067-50:
Universal 4th Order Low Noise,
Rail-to-Rail Switched Capacitor Filters
by Doug La Porte
Introduction
Modern products require ever smaller
and more efficient designs. Much of
yesterday’s desktop equipment has
been replaced by small, often batteryoperated, portable systems in today’s
world. Filter products must follow
this trend and must address the
requirements of today’s system
designer. These requirements include
small package size, operation at
reduced power supply voltages, low
power consumption and large output
voltage swings to accommodate high
dynamic-range signals.
The LTC1068 family of universal,
8th order switched capacitor filters
were the first products to answer the
bell. They are half the size of the
previous generation of devices and
their performance is superior in every
respect. Next, the LTC1069 family of
preconfigured, fully integrated,
switched capacitor filters raised the
bar in performance and ease of use.
The LTC1069’s performance specifications, coupled with standard SO-8
packaging and zero external components, match the needs of modern
systems. Now, a brand new family of
parts has been added to the Linear
Technology filter portfolio: the
LTC1067 and LTC1067-50.
Why Another Building Block?
The LTC1068 family provides an excellent solution for high performance
8th order filters, but many systems
do not need an 8th order filter; a 4th
order filter will do the job. These
systems will either use the LTC1068
with extra unused sections or one of
the older MF-10-type parts. The MF10, in its many versions, was a fine
product in its day, but its day has
passed. Modern systems must operate on low power supply voltages. The
MF-10 parts are only good down to a
6
5V supply and most systems today
use 3.3V supplies. To get acceptable
performance and high dynamic range
on a 3.3V power supply, the filter
must have a low noise input structure and provide a large output swing.
If the output only swings to 800mV
from the positive supply rail, you are
throwing away about 25% of the
available dynamic range. For this reason, a rail-to-rail output stage is
desired. On the lower supply voltages, the part’s DC offset also becomes
more significant. The LTC1067 and
LTC1067-50 were designed to fill the
needs of the 4th order filter market. It
is not just another version of the MF10, but a completely new design. It is
made for modern systems; it operates
on a 3V power supply, with low DC
offset, low input noise, rail-to-rail
output swing, low power consumption and small packaging. These new
parts also deliver much tighter frequency accuracy than any previous
product. This opens the door to reliable, repeatable narrow-band filter
designs.
LTC1067 and
LTC1067-50 Overview
The LTC1067 and the LTC1067-50
are universal, 4th order switched
capacitor filters with rail-to-rail
operation. Each part contains two
identical, high accuracy, very wide
dynamic-range 2nd order filter building blocks. The block diagram for
both parts is identical (see Figure 1).
Each building block, together with
three to five resistors, provides 2nd
order filter transfer functions, including lowpass, bandpass, highpass,
notch and allpass. These parts can be
used to easily design 4th order or
dual 2nd order filters.
Linear Technology’s new
FilterCAD™ for Windows® filter design
software fully supports designs with
these parts. FilterCAD is a very powerful Windows-based filter design
program, available free of charge from
Linear Technology. Consult Linear
Technology’s marketing or applications staff for more information.
Windows is a registered trademark of Microsoft Corp.
V+
(1)
INV A
(8)
V+
(3)
HPA/NA (7)
LPA (5)
BPB (11)
LPB (12)
–
∑
15k AGND
(15)
+
SA (4)
HPB/NB (10)
V–
(14)
BPA (6)
+
15k
INV B
(9)
∑
–
CLK (16)
1067_01.eps
SB (13)
Figure 1. LTC1067/LTC1067-50 block diagram
Linear Technology Magazine • August 1997
DESIGN FEATURES
1
2
3
V+
4
0.1µF
5
6
7
8
STAR
SYSTEM
GROUND
V+
CLK
NC
AGND
1
16
2
15
14
V + LTC1067 V –
LTC1067-50
13
SA
SB
12
LPA
LPB
11
BPA
BPB
10
HPA/NA HPB/NB
9
INV A
INV B
V
–
0.1µF
V+
0.1µF
STAR
SYSTEM
GROUND
CLOCK
SOURCE
Linear Technology Magazine • August 1997
1µF
14
DIGITAL
GROUND
PLANE
200Ω
CLOCK
SOURCE
FOR MODE 3, THE SA AND SB SUMMING NODE PINS
ARE TIED TO THE AGND PIN
1067_02b.eps
Figure 2b. Single-supply ground plane connections
supply and 4.35mA from a ±5V supply. The LTC1067-50 typically
consumes about one half of the
LTC1067’s supply current: 1.0mA
from a 3V supply, 1.45mA from a
4.75V supply and 2.35mA from a ±5V
supply. The LTC1067-50 is a lower
power, slightly faster version of the
LTC1067. However, the LTC1067 has
slightly lower noise, lower DC offset
and tighter fO tolerance than the
LTC1067-50. These parts allow the
designer to trade off one set of specifications for the other. The LTC1067
is preferred, by virtue of its higher
sampling rate, for notch and highpass
filters, due to the broad-band nature
of these filters.
Both parts are designed for single❏ Rail-to-rail input and output
or dual-supply-voltage applications.
operation
The parts have an integrated voltage
❏ Operation from single 3V to ±5V
divider network; only a decoupling
supply
capacitor is required to set a mid❏ 16-pin narrow SSOP or SO-16
supply potential for single-supply
packages
systems. Figure 2 shows the power
❏ >80dB dynamic range from a
supply connections for dual- and
3.3V supply
single-supply operation.
❏ Tight fO accuracy: ±0.2% typical,
The LTC1067 and LTC1067-50 are
±0.55% maximum
ideally suited for today’s systems.
❏ Low DC offset: ≤ 5mV typical
The ability to operate on low supply
❏ Low noise: < 70µVRMS (4th order
voltages, with low supply current,
Butterworth LPF)
combined with low noise, low DC offThese parts also consume small set and rail-to-rail output swing,
amounts of supply current. The makes these parts perfect for batteryLTC1067 typically draws 2.0mA from operated systems that require high
a 3V supply, 2.55mA from a 4.75V dynamic range. The small 16-pin narThe center frequency of each 2nd
order section is tuned by an external
clock. The LTC1067 has a 100:1 clockto-center frequency ratio. The
LTC1067-50’s clock-to-center frequency ratio is 50:1. Both of these
parts are double sampled. Double
sampling has the advantage of placing all aliasing and imaging issues at
twice the clock frequency. Ratios other
than 100:1 or 50:1 are achieved by
using external resistors and choosing
the operating mode configuration. For
more details on the operating modes,
consult the LTC1067/LTC1067-50
data sheet.
The LTC1067 and LTC1067-50
have the following salient features:
15
LTC1067-50
13
SA
SB
12
LPA
LPB
11
BPA
BPB
10
HPA/NA HPB/NB
9
INV A
INV B
8
Figure 2a. Dual-supply ground plane connections
AGND
4
7
1067_02a.eps
NC
16
V + LTC1067 V –
6
200Ω
CLK
3
5
DIGITAL
GROUND
PLANE
V+
row SSOP package is also in line with
the compact packaging requirements.
These parts also feature tight fO accuracy, allowing highly repeatable,
manufacturable narrow-bandwidth
bandpass and notch filters.
The LTC1067 and LTC1067-50 are
also mask programmable. This allows
the designer to specify the filter’s
response and have the part delivered
as a fully optimized, integrated solution that has been tested to meet the
exact system specifications. Maskprogrammed parts have all external
resistors integrated, have the supply
current adjusted for the specific
application and come in the small
SO-8 package. This results in a
minimal-real-estate, zero-externalcomponents design that is optimized
and tested to meet the design requirements. For more information on
mask-programmed parts, call Linear
Technology’s marketing department.
When designing filters, especially
high Q filters, consult the “Maximum
Q vs Center Frequency” curves and
the applications information in the
LTC1067/LTC1067-50 data sheet.
These curves serve as a guide to how
fast you can push any design and still
maintain a highly repeatable design.
Using the FilterCAD design software
will automatically alert you to any
design that is beyond the limits of the
part.
7
DESIGN FEATURES
Let the Games Begin:
Some LTC1067 and
LTC1067-50 Applications
CMOS LOGIC GATE
1
3.3V
2
0.1µF
3
High Dynamic-Range
Butterworth Lowpass Filter
with Built-In Track-and-Hold
Challenges Discrete Designs
R21, 40.2k
VIN
R11
52.3k
8
V–
SA
SB
LTC1067
LPA
LPB
BPA
BPB
HPA
HPB
INV A
INV B
TRACK HOLD
14
approaching the supply rails. Previous parts could not attain this high
dynamic range due to higher input
noise levels, poor linearity and limited output-stage signal swing. The
low noise and rail-to-rail output swing
are especially crucial on the lower
3.3V power supply, where every bit of
detectable signal range is precious.
Figure 6 shows the same plot for the
LTC1067-50 circuit. The dynamic
range is not quite equal to that of the
LTC1067, but is still very good. Recall
that, for the same clock frequency,
the LTC1067-50 based filter has
double the bandwidth and half the
supply current of the LTC1067.
The LTC1067 and LTC1067-50 also
perform a track-and-hold function.
Stopping the clock holds the output
of the filter at its last value. The
LTC1067 is the best performing part
in this area. The LTC1067’s hold step
is less than –100µV and the droop
rate is less than –50µV/ms over the
full temperature range. These num-
–10.00
–60.00
11
R32, 40.2k
10
R22, 76.8k
9
bers compare very favorably with dedicated track-and-hold amplifiers.
When the clock is restarted, the filter
resumes normal operation within ten
clock cycles and the output will then
correctly reflect the input as soon as
the filter’s mathematical response
allows.
Elliptic Lowpass Filter
The LTC1067 family is capable of
much more challenging filters. Figure
7 shows the schematic for a 25kHz
elliptic lowpass filter using the
LT1067-50 operating on a 5V supply.
Maximum attenuation one octave
from the –3dB corner is the design
goal for this filter. Figure 8 shows the
frequency response of the filter with
the –3dB cutoff at 25kHz and –48dB
of attenuation at 50kHz. The broadband noise of the filter is 85µVRMS
and the DC offset is less than 15mV
typically.
Although Figure 7 shows the filter
powered by a single 5V supply, 3.3V
–50.00
VSUPPLY = 3.3V
–70.00
–75.00
–80.00
–70.00
–75.00
–80.00
–85.00
–90.00
–90.00
–80.00
–95.00
–95.00
–100.00
–100.00
1067_04.EPS
Figure 4. Transfer function of the LTC1067
5kHz Butterworth LPF
0.1
1
INPUT VOLTAGE (Vp-p)
10
1067_05.EPS
Figure 5. Dynamic range of LTC1067
Butterworth LPF
VSUPPLY = 3.3V
–65.00
–70.00
100k
VSUPPLY = 5V
–60.00
VSUPPLY = 5V
–65.00
VSUPPLY = ±5V
–55.00
VSUPPLY = ±5V
–85.00
10k
FREQUENCY (Hz)
R42, 76.8k
12
–60.00
–90.00
1k
1µF
13
Figure 3. High dynamic-range Butterworth LPF with track-and-hold control
–55.00
–50.00
7
V+
15
1067_03.EPS
–50.00
–40.00
6
AGND
500kHz
VOUT
0
–30.00
5
NC
16
RL1, 59k
S/N +THD (dB)
GAIN (dB)
R31, 49.9k
10.000
–20.00
8
R41, 40.2k
CLK
V
S/N +THD (dB)
Figure 3 shows an LTC1067 configured as a 5kHz Butterworth lowpass
filter. This circuit runs on a 3.3V
power supply and uses an external
logic gate to stop the clock for trackand-hold operation. The transfer
function for this circuit, shown in
Figure 4, is the classical Butterworth
response. This circuit can be used
with either the LTC1067 or the
LTC1067-50. The broad-band noise
for the LTC1067 circuit is 45µVRMS
and the DC offset is typically less
than 10mV. For the LTC1067-50, the
broad-band noise is 55µVRMS and the
DC offset is typically less than 15mV.
This circuit has tremendous
dynamic range, even on low supply
voltages. Figure 5 shows a plot of the
LTC1067’s signal-to-noise plus total
harmonic distortion (SINAD) vs input
signal level for a 1kHz input at three
different power supply voltages.
SINAD is limited for small signals by
the noise floor of the LTC1067, for
medium signals by the part’s linearity and for large signals by the output
signal swing. The part’s low noise
input stage and excellent linearity
allow the SINAD to exceed 80dB for
signals as small as 700mVP-P, while
the rail-to-rail output stage maintains this level for input signals
4
+
0.1
1
INPUT VOLTAGE (VP-P)
10
1067_06.EPS
Figure 6. Dynamic range of LTC1067-50
Butterworth LPF
Linear Technology Magazine • August 1997
DESIGN FEATURES
1
5V
2
0.1µF
3
R61, 48.7k
4
R51
4.99k
R31, 49.9k
R21, 20k
R11
53.6k
5
6
7
8
VIN
+
CLK
NC
AGND
V+
V–
SA
SB
V
LTC1067-50
LPA
LPB
BPA
BPB
HPA
HPB
INV A
INV B
RH1, 93.1k
RL1, 25.5k
16
2
1.25MHz
15
1µF
14
5
R62, 6.04k
13
R52
12 4.99k
11
R32, 21k
10
R22, 24.9k
Narrow-band bandpass filters are difficult to design but are easily
achievable with these parts. Most
applications for these filters involve
extracting a low level signal from a
noisy environment. The noise may be
the standard broad-band, Gaussian10.000
0
–10.00
GAIN (dB)
–20.00
–30.00
–40.00
–50.00
–60.00
–70.00
–80.00
–90.00
1k
10k
FREQUENCY (Hz)
100k 200k
1067_08.EPS
Figure 8. Transfer function of LTC1067-50
25kHz LPF
Linear Technology Magazine • August 1997
R31, 200k
6
R21, 10k
7
R11
200k
8
IN
RG, 21k
CLK
NC
AGND
V+
V–
LTC1067
SA
SB
LPA
LPB
BPA
BPB
HPA/NA HPB/NB
INV A
INV B
16
fCLK = 500kHz
15
1µF
14
13
12
OUT
11
R32, 200k
10
R22, 10k
9
R12, 200k
9
1067_09.eps
RH2, 487k
RL2, 20k
–
Figure 9. Low noise, low voltage narrow BPF
1/2 LT1498
+
VOUT
Figure 7. 25kHz elliptic lowpass filter
Narrow-Band Bandpass Filter
Design Extracts Small Signals
Buried in Noise
4
0.1µF
1067_07.EPS
or ±5V supply operation is also
supported. The maximum cutoff frequency is 15kHz for the 3.3V supply
and 35kHz for the ±5V supply. The
same design and schematic used with
an LTC1067 will achieve a somewhat
lower noise, lower DC-offset filter.
With the LTC1067, the broad-band
noise is 70µVRMS and the DC offset is
typically less than 10mV. The maximum operating frequencies for the
LTC1067 are one half of those for the
LTC1067-50.
3
3.3V
type noise or it may consist of multiple interfering signals. For example,
the signal may be a low level tone or a
narrow-bandwidth modulated signal,
in a voice-band system. The presence
of the tone must be detected even
while the large voice signals are
present. A narrow-band bandpass filter will allow the tone to be separated
and detected even in this hostile environment. Numerous systems also
require a narrow bandpass filter to be
swept across a band looking for the
tones. Switched capacitor filters allow
the filter to be swept by simply changing the clock frequency.
To achieve success in designing
narrow-band bandpass filters, you
must start with precision components.
In an LC or RC design, you would
have to start with 0.1% resistors, 1%
inductors and 1% capacitors to have
any hope of finishing with a successful, repeatable design in production.
A competing solution, a digital filter
implementation, also requires precision components. The full input signal
(signal, noise and out-of-band interference) must be correctly digitized
and then processed with a DSP device
to finally determine the tone’s presence. If an out-of-band interfering
signal is 20dB greater than the desired
tone, the ADC must have an extra
20dB of dynamic range above the
signal’s requirement. To pull a smallsignal tone from a large signal
interferer, you may need a 16-bit ADC
to digitize the signal just to get 12-bit
resolution of the tone after process-
ing. The added cost, power, board
space and development time make
this approach unattractive.
A precision switched capacitor filter provides a simple, small, low power,
repeatable, inexpensive solution. The
older MF-10-type parts do not have
the necessary fO accuracy to achieve
a reliable, repeatable design. Figure 9
shows the schematic of a narrowband bandpass filter centered at 5kHz.
The design uses two identical cascaded sections, each with a Q of 20.
Multiply the individual Q of each section by 1.554 to calculate the total Q
of a filter with two identical fO, identical Q sections. This filter has a total Q
of 31. For tunable filter applications,
simply lowering the clock frequency
lowers the center frequency of the
filter. Figure 10 shows the frequency
response of this filter. The broadband noise of this filter is only
90µVRMS. Highly selective bandpass
filters are possible due to the
LTC1067’s excellent fO accuracy.
Higher Q, narrower bandwidth filters are achievable with 0.1% resistors
0
–10
GAIN (dB)
1
V+
–20
–30
–40
4.0
4.5
5.0
5.5
6.0
FREQUENCY (kHz)
1067_10.eps
Figure 10. Frequency response of narrow BPF
9
DESIGN FEATURES
The pole should be greater than thirty
times the notch frequency and less
than seventy-five times the notch frequency for the best results. Figure 12
shows the frequency response of the
filter. Note that the notch depth is
greater than –80dB. Without the use
of the C21 and C22, the notch depth
is only about –35dB.
Narrow-Band
Notch Filter Design
Reaches 80dB Notch Depth
Conclusion
Narrow-band notch filters are especially challenging designs. The
requirement for most notch filters is
to remove a particular tone and not
affect any of the remaining signal
bandwidth. This requires an infinitesimally narrow filter that can only
be approximated by a reasonably
narrow bandwidth. These types of
filters, like the narrow-band bandpass
discussed above, require precision fO
accuracy. Figure 11 shows the schematic of this type of filter. This filter is
a 1.02kHz notch filter that is often
used in telecommunication test
systems.
One of the challenges of designing
a switched capacitor notch filter
involves the broad-band nature of a
notch filter. The broad-band noise
can be aliased down into the band of
interest. Optimal high performance
notch filters should employ some form
of noise-band limiting. To accomplish
the noise-band limiting, the design in
Figure 11 places capacitors in parallel with the R2 resistors of each 2nd
order section. This forms a pole, set at
fP = 1/(2 • π • R2 • C2), that will limit
the bandwidth. This pole frequency
must be low enough to have a bandlimiting effect but must not be so low
as to affect the notch filter’s response.
0
–10
–20
–30
GAIN (dB)
or matched resistor networks. An
LTC1067 mask-programmed part is
ideal for these ultranarrow filters.
The well matched, on-chip resistors,
coupled with specified test conditions,
yield a fully functioning filter module,
in an SO-8 package, without any of
the hassles or cost of procuring precision resistors or resistor networks.
–40
–50
–60
–70
–80
–90
–100
900
1000
1100
FREQUENCY (Hz)
800
Modern systems’ requirements are
different from those of the past. The
LTC1067 and LTC1067-50 are brand
new filter products optimized for
today’s systems. They are small, highly
accurate, low power, rail-to-rail, low
noise building blocks that have tremendous versatility.
1
5V
0.1µF
2
1200
LT1067_12.eps
Figure 12. Measured frequency response of
Figure 11’s narrow-band notch filter
V+
CLK
NC
AGND
V+
V–
16
200Ω
fCLK = 125kHz
15
1µF
3
R61*
9.88k
R51*
4.99k
R32
61.9k
R21
10k
4
5
6
7
LTC1067
SA
SB
LPA
LPB
BPA
BPB
HPA/NA
C21**
300pF
R11
18.7k
VIN***
HPB/NB
14
13
R62*
10k
12
R52*
4.99k
11
R32
464k
10
R22
75k
VOUT
C22**
30pF
8
INV A
INV B
9
RH1
40.2k
1067_11.eps
* R51, R61, R52, R62 ARE 0.1% TOLERANCE RESISTORS
** C21 AND C22 IMPROVE THE NOTCH DEPTH WHERE
1
(30)(f NOTCH) <
< (75)(f NOTCH) WITHOUT
2π(R2X)(C2X)
C21 AND C22 THE NOTCH DEPTH IS LIMITED TO –35dB
*** VIN ≤ 1.25VP-P
Figure 11. Narrow-band notch filter
for
the latest information
on LTC products,
visit
www.linear-tech.com
10
Linear Technology Magazine • August 1997
DESIGN FEATURES
LTC1422: Simple and Versatile
Hot Swap Solution
by David Soo
Introduction
Typical Application
Like the LTC1421 Hot Swap controller, introduced in the August, 1996
issue of Linear Technology the
LTC1422 can handle supply voltages
in the 3V–12V range. The difference
between these two parts is in the
number of supplies that can be independently controlled: the LTC1421 is
a 3-channel device, whereas the
LTC1422 is a single-channel device.
Figure 1 shows a typical application using the LTC1422. In order to
protect the board and capacitors, a
series-pass transistor, Q1, is placed
between the connector and the capacitors. The voltage at the gate of the
pass transistor is raised at a conR1
0.005Ω
PLUG-IN CARD
VCC
Q1
MTB56N06V
VCC
8
+
ON 2
CONNECTOR 1
2.47
UVL
–
REF
CHARGE
PUMP
Cp3
10µs
FILTER
Cp1
2.0µA
LOGIC
+
1.232V
REFERENCE
REF
GLITCH
FILTER
Cp2
TIMER 3
REF
Q1
C2
0.33µF
–
C4
2200µF
50mV
R3
6.81K
1%
–
CONNECTOR 2
+
+
C1
1.0µF
–
–+
ON/RESET
GATE
6
SENSE
7
VOUT
5V/5A
R2
10Ω
5%
+
BACKPLANE
trolled rate. Because Q1 is an Nchannel transistor, the supply on the
board follows the gate ramp minus a
threshold voltage. The capacitorcharging current is limited to the
capacitor value times the ramp rate of
the pass-transistor gate (I = C × dv/dt).
Due to special enhancements to
the LTC1422, the supply pin can withstand any supply ramp-up rate.
Following the connection of power to
the chip, there is a time delay before
the GATE pin voltage starts to
increase. This allows time for the connector to seat after numerous
bounces. This time delay is programmed with the capacitor C2 on
the TIMER pin. The ON pin is normally pulled high to allow the part to
automatically turn on the pass transistor at power-up. If the ON pin is
brought low, the GATE pin will be
held at ground.
tantly, the LTC1422 combines these
features in a compact 8-pin package
that simplifies the design of any hotswapped system.
When a circuit board is plugged into a
live backplane, the supply bypass
capacitors can draw large transient
currents from the backplane power
bus as they charge. These inrush
currents can destroy board traces or,
at the least, disrupt the supply with a
large negative transient. There is a
need for a protection circuit to power
up the board in a controlled manner
and provide a low series-resistance
connection during normal operation.
The LTC1422 allows a board to be
safely inserted into and removed from
a live backplane. The rate at which
the supply ramps up at the board is
programmable. In addition to hot swap
protection, it has a voltage monitor
and reset output that can be used to
supervise the board’s circuitry. The
device also has overcurrent protection, which disconnects the board
during a short circuit. Most impor-
5 FB
R4
2.43K
1%
µP
12µA
Cp4
1 RESET
RESET
Q2
LTC1422
4 GND
GND
1422_01.EPS
Figure 1. LTC1422 typical application
Linear Technology Magazine • August 1997
11
DESIGN FEATURES
1
2
3
4
70
5
TA = 25°C
GLITCH FILTER TIME (µs)
60
ON
2.45V
VCC
50
40
30
20
1.232V
1.232V
10
0
TIMER
40
80
120
160
200
220
FEEDBACK TRANSIENT VOLTAGE (mV)
1422_03.EPS
Figure 3. Glitch filter time vs feedback
transient voltage
GATE
VOUT
RESET
Figure 2. Typical insertion timing
1422_02.EPS
1
2
30µs
3
4
5
6
40µs
ON
15µs
TIMER
The timing for the board during
board connection is shown in Figure
2. When the connector makes initial
contact at time point 1, the ON pin is
pulled high. If VCC is greater than the
2.45V undervoltage lockout threshold, the TIMER pin starts charging C2
with a 2µA current source. At time
point 2, the supply opens. VCC now
drops below the undervoltage threshold, signaling the LTC1422 to
discharge the TIMER pin and wait for
supply connection. Once the connector is seated, the TIMER pin completes
a full timing cycle by charging to the
1.232V threshold and the voltage at
the GATE pin begins to rise (time
point 3). The rate at which the voltage
at the gate of the pass transistor, Q1,
increases is controlled by sourcing a
10µA current source into C1. Onchip charge pumps provide gate drive
of at least twice VCC to Q1.
Voltage Monitor
GATE
VOUT
RESET
20µs
1422_04.EPS
Figure 4. Soft-reset timing
12
The LTC1422 uses a 1.232V reference, a precision voltage comparator
and an external resistive divider to
monitor the output supply voltage.
When the voltage at the FB pin rises
above its reset threshold voltage
(1.232V), comparator Cp2’s output
goes high and a timing cycle starts
(Figure 2, time point 4). After a complete timing cycle, RESET is pulled
high (time point 5). The 12µA pull-up
current source to VCC on RESET has
a series diode so the pin can be pulled
above VCC by an external pull-up
resistor without forcing current back
into the supply.
Linear Technology Magazine • August 1997
DESIGN FEATURES
1
pin goes low and stays low for one
timing cycle.
If the ON pin is held low for longer
than 40µs, the GATE will turn off and
the RESET pin will eventually go low
(time points 4, 5 and 6).
2
40µs
ON
10µs
VCC – VSENSE
VCC
1.232V
1.232V
1.232V
1.232V
TIMER
GATE
VOUT
RESET
1422_05.EPS
Figure 5. Electronic circuit-breaker timing
Glitch Filter
Soft Reset
The LTC1422 has a glitch filter to
prevent RESET from generating a
system reset when there are transients
on the FB pin. The filter is 20µs for
large transients (greater than 150mV)
and up to 80µs for small transients.
The relationship between glitch-filter
time and the feedback transient voltage is shown in Figure 3.
In some cases, a system reset without
a power-down is desirable. The ON
pin can signal the RESET pin to go
low without turning off the power (a
soft reset). This is accomplished by
holding the ON pin low for only 15µs
or less ( Figure 4, time point 1). At
about 30µs from the falling edge of
the ON pin (time point 2) the RESET
Hot Swapping Two Supplies
With two external pass transistors,
the LTC1422 can switch two supplies. In some cases, it is necessary to
bring the dominant supply up first
during power-up and ramp it down
last during the power-down phase.
The circuit in Figure 6 shows how to
program two different delays for the
pass transistors. The 5V supply is
powered up first. R1 and C3 are used
to set the rise and fall delays on the 5V
supply. Next, the 3.3V supply ramps
up with a 20ms delay set by R6 and
C2. On the falling edge, the 3.3V
supply ramps down first because R6
is bypassed by the diode, D1.
Electronic Circuit Breaker
The LTC1422 features an electronic
circuit-breaker function that protects
against short circuits or excessive
currents from the supply. By placing
a sense resistor between the supply
input and SENSE pin, the circuit
Q2
1/2 Si4936
3.3V IN
3.3V OUT
C4
470µF
16V
R7
10Ω
5%
Q1
CURRENT LIMIT = 5A
1/2 Si4936
5.0V OUT
5.0V IN
R2
0.01Ω
5%
5V OUT
3.3V OUT
RESET
ON
1
2
3
4
C1
0.33µF
16V
RESET
VCC
SENSE
ON
TIMER
GND
GATE
FB
8
C5
470µF
16V
R3
10Ω
5%
R1
10k
5%
D1
1N4148
7
R4
2.74k
1%
6
R6, 1M 5%
5
TRIP POINT = 4.6V
LTC1422
C3
0.047µF
25V
C2
0.022µF
25V
R5
1k
1%
GND
1422_06.EPS
Figure 6. Hot swapping 5V and 3.3V
Linear Technology Magazine • August 1997
13
DESIGN FEATURES
breaker will be tripped whenever the
voltage across the sense resistor is
greater than 50mV for more than
10µs. When the circuit breaker trips,
the GATE pin is immediately pulled to
ground and the external N-channel
MOSFET is quickly turned off (Figure
5, time point 1). When the ON pin is
cycled off for longer than 40µs and
then cycled on (time point 2), the
circuit breaker is reset and another
turn-on cycle is started. If the circuit
breaker feature is not required, the
SENSE pin should be shorted to VCC.
follower used in previous applications.
This allows the ground of the LTC1422
to connect to the negative terminal of
the 48V input. The clamp circuit consisting of R5 and D1 provides power
to the LTC1422.
The ON pin threshold is set at
1.232V by the reference and comparator Cp1 (Figure1). This allows
the resistive divider of R1 and R2 in
Figure 7 to monitor the input supply.
When the supply is greater than 37V
a timing cycle is generated and the
pass transistor Q1 is turned on.
Because the pass transistor is in a
Hot Swapping a 48V DC/DC
common-source configuration, care
Module with an Active-Low
must be taken to limit the inrush
On/Off Control Signal
current into capacitor C3. One way to
Using a 5.1V Zener and a resistor, the do this is to precharge C3 using resisLTC1422 can switch supplies much tor R4. As the input rises, current
greater than its 12V VCC pin rating. As flows through R4 and charges capacishown in Figure 7, the pass transis- tor C3. Once the input supply crosses
tor, Q1, is connected as a common 37V, there is a timing cycle followed
source driver rather than as the source by the ramp-up of the GATE pin. By
this time, capacitor C3 is sufficiently
charged, thereby limiting the inrush
current. Another method for limiting
the inrush current is to slow down the
ramp-up rate of the GATE pin.
The reset comparator is used to
monitor the gate voltage. 290ms after
the voltage at the GATE pin exceeds
5.8V, the RESET pin will source 12µA
into Q2. The high voltage transistor
Q2 is used to translate the RESET
signal to the module On/Off input.
Conclusion
Designing hot insertion systems
requires a significant effort by an
experienced analog designer. One way
to reduce the design effort is to use a
Hot Swap building block, such as the
LTC1422, which offers a charge-pump
gate driver, a millisecond timer and
other specialized features. With the
LTC1422, designers can easily create
safe and reliable hot-swapped
systems.
VIN+
VOUT+
5V
SENSE+
C3
100µF
100V
R1
36k
5%
AT&T
JW050A1-E
50W
SENSE–
R5
10k
5%
VIN–
VOUT–
ON/OFF
+
48V
–
1 RESET
Q2
MMBT5551LT1
2
3
4
R2
1.2k
5%
C1
0.47µF
25V
ON
TIMER
VCC
SENSE
GATE
FB
GND
LTC1422
8
7
6
5
C4
1µF
25V
D1
5.1V
1N751A
R6
1M
5%
R7
270k
5%
R3
10Ω
5%
C2
0.1µF
25V
Q1
IRF530
R4
CIRCUIT TURNS ON WHEN VIN > 37V
CIRCUIT FOR ACTIVE LOW TURN-ON MODULES
510Ω, 5%
OPTIONAL PRECHARGE
RESISTOR
1422-07.EPS
Figure 7. Hot swapping an AT&T 48V module
14
Linear Technology Magazine • August 1997
DESIGN FEATURES
LTC1626 Low Voltage Monolithic
Step-Down Converter Operates
by Tim Skovmand
from a Single Li-Ion Cell
Introduction
The LTC1626 is a monolithic, low
voltage, step-down current mode DC/
DC converter with an input supply
voltage range of 2.5V to 6V, making it
ideal for single-cell Li-Ion or 3- to 4cell NiCd/NiMH applications. A
built-in 0.32Ω P-channel switch (VIN =
4.5V) allows up to 0.6A of output
current. The maximum peak inductor
current is externally programmable
to minimize component size in lower
current applications.
The LTC1626 incorporates automatic power saving Burst Mode
operation to reduce gate-charge losses
when the load current drops below
the level required for continuous
operation. With no load, the converter
draws only 160µA; in shutdown it
draws a mere 1µA—making it ideal
for current-sensitive applications.
Single-Cell Li-Ion Operation
As shown in Figure 1, a fully charged
single-cell Li-Ion battery begins the
discharge cycle at either 4.1V or 4.2V
(depending upon the manufacturer’s
charge voltage specifications). During
the bulk of the discharge time, the cell
produces between 3.5V and 4.0V.
Finally, toward the end of discharge,
the cell voltage drops fairly quickly
Using the circuit shown in Figure 3,
efficiencies of greater than 90% are
maintained from 20mA to 250mA of
load current with a 3.5V input supply
voltage, as shown in Figure 4.
Current Mode Architecture
The LTC1626 is a current mode DC/
DC converter with Burst Mode operation. This results in a power supply
that has very high efficiency over a
wide load-current range, fast transient response and a very low dropout
characteristic.
An external, small valued sense
resistor, RSENSE, provides current feedback, which allows the LTC1626 to
continuously control the inductor
current. When the load is heavy, the
LTC1626 is in continuous operation.
During the switch on-time, a built-in
current comparator monitors the voltage between the SENSE+ and SENSE–
pins connected across the external
As the Li-Ion cell discharges, the
LTC1626 smoothly shifts from a high
efficiency switch-mode DC/DC regulator to a low dropout (100% duty
cycle) linear regulator. In this mode,
the voltage drop between the battery
input and the regulator output is
determined by the load current and
the series resistance of the internal Pchannel power MOSFET, the current
sense resistor and the inductor resistance. When the battery voltage rises
(VIN = 2.7V TO 4.5V)
+
0.1µF
+
VIN
PWR VIN
LBIN
4.5
Li-Ion CELL VOLTAGE (V)
High Efficiency Operation
100% Duty Cycle
in Dropout Mode
SINGLE
Li-Ion
CELL
5.0
again, the LTC1626 smoothly shifts
back to a high efficiency DC/DC
converter.
below 3V. It is recommended that the
discharge be terminated somewhere
between 2.2V and 2.8V (again,
depending upon the manufacturer’s
specifications).
The LTC1626 is specifically
designed to accommodate a singlecell Li-Ion discharge curve. For
example, using the circuit shown in
Figure 2, it is possible to produce a
stable 2.5V/0.25A regulated output
voltage with as little as a 2.7V from
the battery—thus obtaining the maximum possible run time.
CIN††
47µF
16V
L1*
22µH
RSENSE**
0.1Ω
VOUT
(2.5V/0.25A)
SW
LTC1626
LBOUT
4.0
D1
MBR0520LT1
PGND
SHDN
3.5
10k
1%
SHUTDOWN
SENSE+
ITH
3.0
1k
2.5
CT
SENSE–
SGND
100pF
CT
270pF
1.5
0
1
2
3
4
5
6
7
DISCHARGE TIME (HOURS)
Figure 1. Typical single-cell Li-Ion discharge
curve
Linear Technology Magazine • August 1997
COUT†
100µF
10V
VFB
3900pF
2.0
+
1000pF
10k
1%
*SUMIDA CDRH62-220
**IRC 1206-R100F
† AVX TPSD107K010
†† AVX TPSD476K016
Figure 2. Single-cell Li-Ion battery to 2.5V converter
15
DESIGN FEATURES
100
VIN (2.7V to 6V)
+
95
0.1µF
VIN
PWR VIN
SHUTDOWN
ITH
470Ω
CT
270pF
3900pF
CT
L*
33µH
RSENSE**
0.1Ω
SW
D1†
LTC1626
+
P GND
COUT††
100µF
6.3V
VIN = 3.5V
90
85
80
SENSE+
1000pF
SGND
VFB
100pF
L1 = 33 µH
V OUT = 2.5V
R SENSE = 0.1 Ω
C T = 270pF
75
10k
1%
SENSE–
*COILTRONICS CTX33-4
**IRC 1206-R100F
†MBRS130LT
††AVX TPSC107M006R0150
†††AVX TPSD476K016
VOUT
2.5V/0.25A
EFFICIENCY (%)
CIN†††
47µF
16V
70
0.01
10k
1%
1.00
0.10
OUTPUT CURRENT (A)
Figure 4. Efficiency vs output load current
Figure 3. High efficiency 2.5V step-down converter
Operating Frequency
The nominal off-time of the LTC1626
is set by an external timing capacitor
connected between the CT pin and
ground. The operating frequency is
then determined by the off-time and
the difference between VIN and VOUT.
Figure 5 is a graph of normalized
operating frequency versus power
supply voltage for the 2.5V regulator
shown in Figure 3. Note that the frequency is relatively constant when
the supply voltage is between 3.6V
and 6V, but drops as the supply voltage approaches the 2.5V regulated
output voltage.
The LTC1626 is capable of operating at frequencies up to 700kHz, but
the highest efficiency is achieved
16
Low Voltage,
Low RDS(ON) Switch
The integrated P-channel switch in
the LTC1626 is designed to provide
extremely low resistance at low supply voltages. Figure 6 is a graph of
switch resistance vs supply voltage.
Note that the RDS(ON) is typically
0.32Ω at 4.5V and only rises to
approximately 0.40Ω at 3.0V. This
low switch resistance ensures high
efficiency switching as well as low
dropout DC characteristics at low
supply voltages.
Low-Battery Detection
A built-in low-battery detector senses
the input voltage through an external
resistive divider. The divided voltage
connects to the (–) input of a voltage
comparator (LBIN) and is compared to
the internal 1.25V reference voltage.
The LBOUT pin is an N-channel
open drain that goes low when the
battery voltage drops below the
threshold voltage. In shutdown, the
comparator is disabled and LBOUT is
in the high impedance state. Figure 7
is a schematic diagram detailing the
low-battery comparator connection
and operation.
Typical Applications
3- or 4-Cell NiCd/NiMH
DC/DC Converter
Figure 8 is a schematic diagram that
shows the LTC1626 being powered
from a 3- or 4-cell NiCd or NiMH
battery pack. (This circuit is also suitable for operation from three or four
alkaline cells.) All the components
2.00
1.80
NORMALIZED FREQUENCY
between 200kHz and 400kHz. As the
frequency increases, losses due to
the gate charge of the P-channel power
MOSFET increase. In space-sensitive
applications, high frequency operation allows the use of smaller
components at the cost of a few efficiency points.
1.60
1.40
1.20
1.00
0.80
L1 = 33 µH
V OUT = 2.5V
R SENSE = 0.1 Ω
C T = 270pF
0.60
0.40
0.20
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
INPUT VOLTAGE (V)
Figure 5. Normalized operating frequency vs
supply voltage
1.00
0.90
TJ = 25˚C
0.80
0.70
RDS(ON) (Ω)
sense resistor in series with the
inductor. When the voltage across the
resistor reaches the comparator’s
threshold value, the internal P-channel MOSFET is switched off. By using
a current mode architecture, the
inductor current is predictable and
well controlled under all operating
conditions, making the selection of
the inductor much easier.
Current mode control also gives
the LTC1626 excellent start-up and
short-circuit recovery characteristics.
For example, when the output is
shorted to ground, the off-time is
extended to prevent inductor current
run away. When the short is removed,
the output capacitor begins to charge
and the off-time gradually decreases.
The output returns smoothly to regulation without overshooting.
0.60
0.50
0.40
0.30
0.20
0.10
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
INPUT VOLTAGE (V)
Figure 6. P-channel switch resistance vs
input voltage
Linear Technology Magazine • August 1997
DESIGN FEATURES
output voltage is set at 2.5V, but is
easily programmed to 3.3V for 4-cell
applications. Simply modify the two
output ladder resistors, R1 and R2,
from 10k each to 15k and 9.09k,
respectively, as shown in Figure 8.
VIN
LTC1626
R2
1%
CFLTR
0.01µF
1.25V
LBOUT
+
LBIN
–
R1
1%
connected to ground. The table in
Figure 9 shows the output current
capability as a function of battery
voltage.
Conclusion
The LTC1626 is specifically designed
to operate from a single-cell Li-Ion
battery. With its low dropout, high
efficiency and micropower operating
modes, it is ideal for battery operated
products and efficiency-sensitive devices such as cellular phones and
handheld industrial and medical
instruments.
Single Li-Ion
3.3V Buck/Boost Converter
The circuit shown in Figure 9 produces 3.3V from an input voltage
ranging from 2.5V to 4.5V. The two
windings of a common inductor core
are used to implement this circuit.
Note that the current sense resistor is
Figure 7. Low-battery detector
shown in this schematic are surface
mount and have been selected to minimize the board space and height. The
(VIN = 2.7V TO 6V)
+
3 OR 4
CELL
NiCD OR
NiMH
+
0.1µF
VIN
PWR VIN
LBIN
CIN††
47µF
16V
L1*
22µH
RSENSE**
0.1Ω
VOUT
2.5V/0.25A
SW
LTC1626
LBOUT
*SUMIDA CDRH62-220
**IRC 1206-R100F
†AVX TPSD107K010
††AVX TPSD476K016
SHDN
R1
10k
1%
D1
MBR0520LT1
PGND
SHUTDOWN
SENSE+
CT
1k
+
1000pF
ITH
SGND
SENSE–
VFB
CT
270pF
3900pF
COUT†
100µF
10V
FOR 3.3V:
R1 = 15k 1%
R2 = 9.09k 1%
R2
10k
1%
100pF
Figure 8. 3- or 4-cell NiCd/NiMH to 2.5V converter
(2.5V TO 4.2V)
L1B
L1A
3
2
L1B
+
0.1µF
VIN
PWR VIN
LBIN
+
CIN††
100µF
16V
33µF
10V*
SW
1
LTC1626
L1A
LBOUT
PGND
MANUFACTURER
PART NO.
COILTRONICS
DALE
CTX33-4
LPT4545-330LA
L1B
33µH
3300pF
SENSE–
CT
75pF
VOUT
3.3V
15k
1%
COUT †
100µF
10V
SGND
SENSE+
100pF
*SANYO OS-CON CAPACITOR
**IRC 1206-R100F
†AVX TPSD107M010R0100
†† AVX TPSE107M016R0100
* DESIGN LIMIT
VFB
CT
1k
200
350
0500*
0500*
0500*
+
3
ITH
2.5
3.0
3.5
4.0
4.2
2
D1
MBRS130LT1
4
SHUTDOWN
SHDN
L1A
33µH
IOUT (mA)
+
TOP VIEW
1
4
Li-Ion
SINGLE
CELL
VIN (V)
1000pF
9.09k
1%
RSENSE**
0.1Ω
Figure 9. Single-cell Li-Ion to 3.3V buck/boost converter
Linear Technology Magazine • August 1997
17
DESIGN FEATURES
LTC1340 Varactor Driver Saves Power
in Cellular Phones
by Dave Bell
Introduction
Designers of wireless communications
equipment are constantly striving to
increase the operating time from a
battery charge. For example, just a
few years ago thirty to forty hours
standby time was considered stateof-the-art for a Global System for
Mobile Communication (GSM) cellular telephone. Today GSM phones
that operate for more than one hundred hours in standby are available.
One of the obvious tactics for achiev-
Even in phones that operate
almost exclusively from 3V
supplies, the frequency
synthesizer may still be
powered from a low noise
5V power supply. This
penalizes the product with
high power consumption
and greater complexity.
ing such long standby time is reduction of the operating voltage, since
reduced operating voltage usually
produces a substantial reduction in
operating power. Whereas most cellular phones used to operate from 5V
supplies, newer models generally operate most circuitry in the range of 3V
to conserve power.
Good things in life usually have
their trade-offs, and so does reduced
operating voltage. Most functions
inside a cellular phone can now be
obtained with operation specified
down to 3V. However, a few circuits
still require higher operating voltages. The transmit power amplifier
generally requires higher operating
voltages to deliver the necessary output power—reducing the operating
voltage here doesn’t reduce the total
power needed. Another area that still
causes problems is the frequency synthesizer. Even in phones that operate
almost exclusively from 3V supplies,
18
the frequency synthesizer may still be
powered from a low noise 5V power
supply. This penalizes the product
with high power consumption and
greater complexity.
Many component manufacturers
now offer frequency synthesizer ICs
and voltage controlled oscillators
(VCOs) that are specified for operation down to 3V, but these still don’t
represent a total solution. The problem lies with the tuning characteristics
of the varactor diode inside the VCO;
even though the VCO itself may be
operable from a 3V supply, the control voltage input (the cathode of a
varactor diode within the VCO’s resonant LC tank) usually requires a swing
greater than 0V to 3V to span the
necessary frequency range. This is
especially true when considering the
extra tuning range needed to account
for production VCO tolerances. What
is really needed is a simple method for
boosting the control voltage applied
to the VCO’s varactor diode—and
that’s precisely what the LTC1340
varactor driver is designed to do.
The LTC1340 is a low noise amplifier with an output that can swing to
nearly twice the supply voltage. A
4MHz on-chip charge-pump DC/DC
converter produces the doubled supply voltage to power the amplifier.
Size is extremely important in modern cellular telephones, so the
LTC1340 is packaged in the diminutive MSOP package. The IC, together
with three ceramic capacitors,
consumes a mere 0.065 in2 of PC
board area.
Frequency
Synthesizer Basics
Figure 1 depicts a basic phase locked
loop (PLL) frequency synthesizer block
diagram. The output of the voltage
controlled oscillator (VCO) is fed to a
phase detector via a programmable
frequency divider. The phase detector
compares the phase of this divided
signal with a reference oscillator.
During the period between rising edges
of the two signals, one of two current
sources is enabled at the output of
the phase detector; a current is
sourced if the VCO phase is lagging,
and a current is sinked if the VCO
phase is leading. These current pulses
occur once per cycle at the reference
oscillator frequency and are integrated
on the loop compensation capacitor.
The net effect is that the control voltage applied to the VCO increases if
VCC
LTC1340
VARACTOR
DRIVER
REFERENCE
FREQUENCY
VCC
VCO
RF
OUTPUT
PHASE
DETECTOR
LOOP
COMP
FREQUENCY
DIVIDER
1340_01.EPS
DIVIDER
PROGRAMMING
FROM µC
Figure 1. Frequency-synthesizer block diagram
Linear Technology Magazine • August 1997
DESIGN FEATURES
CCP
0.1µF
(EXTERNAL)
LTC1340
CP
AVCC
47.9pF
PGND
VCC
0.1µF
SHDN
DOUBLER
CHARGE
PUMP WITH
INTERNAL
FLYING
CAPACITOR
50Ω
–
1.15M
62.3pF
VS
0.62V
1.5M
OUT
±20µA
+
COUT
(EXTERNAL)
+
–
AGND
PGND
IN
1340_02.eps
Figure 2. LTC1340 block diagram
the phase is lagging and decreases if
the phase is leading until the phase
error approaches zero.
Loop compensation components
are selected to optimize settling time
for the PLL, while keeping “reference
spurs” at acceptable levels (reference
spurs are unwanted sidebands in the
VCO output spectrum at harmonics
of the reference frequency). The VCO
feedback divider ratio is controlled by
a microcontroller to program the
desired output frequency to multiples
of the reference oscillator frequency.
As mentioned earlier, the phase
detector output comprises two current sources. Operating the phase
detector output voltage too close to
either ground or the positive supply
rail causes one of the two current
sources to saturate. Usually about
400mV headroom is needed for the
current sources to perform within
specifications. This means that the
VCO control-voltage range is reduced
even further because of the headroom required at the phase detector
output, with this penalty increasing
as a percentage of the total range as
supply voltage is reduced. For
example, with a 3V power supply the
allowable control voltage is approximately 0.4V to 2.6V. The LTC1340
varactor driver is designed to be
inserted between the phase detector
and the VCO in order to provide a
much larger voltage swing at the VCO
while keeping the phase detector current sources in the linear region.
Linear Technology Magazine • August 1997
LTC1340 Circuit Description
Noise is the Nemesis
The LTC1340 is conceptually simple—
it is a low noise amplifier combined
with a charge-pump voltage doubler
on the same IC (refer to Figure 2). This
is possible because the intended load,
a varactor diode, is reverse biased
and thus requires practically zero DC
current. All that is needed is sufficient output current to slew the
varactor diode’s junction capacitance
in parallel with the amplifier’s own
output filter capacitor. The amplifier
is capable of delivering approximately
±20µA from its output, so the slew
rate isn’t anything to brag about, but
it’s sufficiently fast for GSM cellular
telephones that must be able to “frequency hop” in approximately 500µs.
A 2MHz on-chip oscillator drives a
biphase charge-pump DC/DC converter, resulting in charge pulses being
delivered at a 4MHz rate. This high
frequency operation has two benefits:
it allows the use of small on-chip
charge-pump capacitors, and it makes
the resultant output ripple easy to
filter. The entire amplifier operates
from the AVCC pin, which is generally
tied directly to the charge-pump output (CP). Although the amplifier
output stage obviously needs this
boosted supply, the amplifier input
stage also benefits. Because of the
boosted supply on the input stage,
the amplifier input is rail-to-rail and
operates properly with a phase
detector signal anywhere between the
input rails.
Low noise is without a doubt the most
critical parameter of the varactor
driver. Noise at the amplifier output
results in unwanted frequency modulation of the VCO, which appears as
sidebands in the output spectrum.
Most RF communications systems
have stringent limits on “out-of-band”
energy, so this noise must be kept to
very low levels. Output noise for the
LTC1340 is typically only 15µVRMS
(25µVRMS maximum) over the 1kHz to
100kHz bandwidth. This keeps the
out-of-band energy about 15dB below
the GSM cellular phone specification
limits with a typical VCO.
Output noise comes primarily from
three sources. The charge-pump DC/
DC converter obviously produces
some 4MHz ripple on the CP pin. This
can be reduced by a filter network
between the CP and AVCC pins, but
this measure is generally unnecessary because of the low ripple present
at the charge-pump output, and the
amplifier’s excellent high frequency
power supply rejection ratio (PSRR).
A transconductance amplifier was
intentionally chosen because it has a
high impedance current source output. This high impedance, coupled
with an output filter capacitor, results
in excellent PSRR even at 4MHz. In
fact, the 4MHz charge-pump ripple
has been reduced to the point where
it is undetectable in output spectrum
plots in an actual frequency synthesizer system. The ground side of the
filter capacitor may be placed directly
19
DESIGN FEATURES
COUT = 470pF
COUT = 1nF
Figure 3. LTC1340 small-signal response
adjacent to the VCO’s ground, alleviating additional noise that might
result from high frequency ground
differential between the LTC1340 and
the VCO.
The amplifier’s input stage also
contributes to output noise, but this
effect has been minimized by keeping
the input stage quiescent current as
high as possible without exceeding
the desired power budget. The size of
the input transistors was also
optimized to put the 1/f noise corner
frequency at approximately 10kHz—
right where the PLL loop response
typically begins to correct for phase
noise. The high impedance feedback
divider also produces thermal noise,
and this, surprisingly, has the largest
effect on output noise. The resistor
values must be kept large to minimize
DC loading on the amplifier output,
but large on-chip capacitors across
the resistors are used to keep noise in
check. Above 2kHz the feedback
impedance is dominated by the capacitors, minimizing the noise
contribution from the high value
resistors.
Other Design Considerations
Although MOSFET transistors have a
much higher 1/f corner frequency
than bipolar transistors, they were
chosen for the input stage to keep
bias current to a minimum. Input
bias current is guaranteed to be 1nA
maximum (25°C) in order to minimize
reference spurs that can result from
input bias current. Because the phase
detector output impedance is high
when both current sources are
disabled, even small amounts of bias
current can result in voltage changes
on the small loop compensation
20
VCC = 6V
TA = 25°C
COUT = 1nF
IOUT = 0A
VSHDN = VCC
11
10
OUTPUT VOLTAGE (V)
COUT = 220pF
12
9
VCC = 5V
8
7
6
VCC = 2.7V
5
4
3
2
1
0
0
1
2
3
4
INPUT VOLTAGE (V)
5
6
1340_04,eps
Figure 4. LTC1340 DC transfer curve
the small PCB area needed, make the
LTC1340 very attractive for modern
cellular telephones.
GSM Frequency Synthesizer
Evaluation Circuit
An evaluation circuit has been developed to demonstrate the performance
of the LTC1340 varactor driver in an
actual frequency synthesizer application. This circuit replicates a
complete transmit frequency synthesizer for a GSM cellular telephone.
Configuration switches allow programming the output to 890MHz,
902.4MHz or 915MHz (bottom, middle
and top of the GSM band).
The GSM cellular protocol supports “frequency hopping”—changing
the frequency rapidly between time
slots. In the case of a GSM cellular
telephone, one synthesizer is often
used for both transmit and receive on
a time-division multiplexed basis. This
requires that the frequency synthesizer be able to change to a new
frequency and stabilize in just over
500µs. The evaluation circuit may
10
0
–10
–20
10dB/DIV
COUT = 0pF
capacitor between phase detector
samples. These voltage changes look
like a low amplitude sawtooth
waveform and result in unwanted
frequency modulation of the VCO at
the reference frequency.
The transconductance amplifier
architecture results in some additional benefits. The current-source
output topology of a transconductance
amplifier naturally provides nearly
rail-to-rail output swing, and this is
essential for maximizing the varactor
drive range. Because the output
capacitor establishes the dominant
pole for the amplifier’s feedback loop,
the amplifier’s bandwidth and slew
rate can be tailored by proper selection of this capacitor. A 1nF output
capacitor results in a bandwidth of
approximately 125kHz. The minimum
recommended output capacitor for
stability is 220pF, resulting in a bandwidth of approximately 560kHz. Both
bandwidth and slew rate are inversely
proportional to output capacitance
over a wide range of values. The relationships among output capacitance,
bandwidth and slew rate can be seen
in Figure 3.
Voltage source VS in Figure 2 produces intentional offset in the
LTC1340’s transfer function. Referring now to Figure 4, it can be seen
that this offset allows the amplifier
output to go within 100mV of ground
even though its noninverting input is
at approximately 400mV. Because the
amplifier has a gain of approximately
2.3, the amplifier output can be saturated high while the input is still
approximately 400mV below the input
supply (assuming a 3V nominal supply voltage). This transfer function
provides for rail-to-rail output swing
while keeping the phase detector current sources in the linear region.
The whole point of reduced
operating voltages in portable communication equipment is power
reduction, so any additional current
consumed by the LTC1340 itself must
be kept small. Only 380µA total current is drawn from a 3V input supply,
allowing significant reductions in
overall system power consumption.
This power efficiency, coupled with
–30
–40
–50
–60
–70
–80
–90
–5 –4 –3 –2 –1 0
SPAN = 1MHz
1
2 3 4 5
1340_05.EPS
RBW = 300Hz
Figure 5. Spectrum plot of frequency
synthesizer’s RF output
Linear Technology Magazine • August 1997
DESIGN FEATURES
Summary
also be programmed to hop between
the bottom and top frequencies once
every millisecond, demonstrating its
ability to hop and settle within 500µs.
Figure 5 shows a spectrum analyzer
plot measured at the synthesizer’s RF
output. The excellent noise performance of the LTC1340 can be seen
from the roughly –75dBc measure-
ment ±100kHz off carrier (each horizontal division is 100kHz). Small
“reference spurs” can be observed at
±200kHz off carrier due to the
synthesizer’s 200kHz reference frequency. The amplitude of these
reference spurs can be traded against
PLL settling time by optimization of
the loop filter components.
for
the latest information
on LTC products,
visit
www.linear-tech.com
The LTC1340 varactor driver is the
smallest, most power-efficient solution for delivering increased varactor
drive to low voltage VCOs. This novel
product neatly fills a “crack” that has
appeared in the block diagram of
portable communications equipment—the need to provide 5V swing
to the VCO control input even though
the rest of the product operates at
3V.
Authors can be contacted
at (408) 432-1900
LT1533, continued from page 5
TRACE A
5V/DIV
TRACE A
5V/DIV
TRACE B
0.5A/DIV
TRACE B
0.5A/DIV
TRACE C
20mV/DIV
TRACE C
20mV/DIV
5µs/DIV
5µs/DIV
1533_07.eps
Figure 7. Limiting switch slew rates (Traces A and B) lowers the high frequency content of the boost regulator’s output ripple (Trace C).
voltage spikes on the output. The
right photo shows the same waveforms with the slew rates lowered
(RCSL = RVSL = 22k), eliminating the
troublesome transients. The penalty
is a drop in efficiency from
85% to 80%.
Conclusion: a Switcher
for Sensitive Systems
With two 1A power switches, the ability to control positive or negative
outputs, and a wide input operating
Linear Technology Magazine • August 1997
range (2.7 to 30V), the LT1533 is a
highly flexible switching regulator.
Thermal shutdown, in addition to
switch-current limit, provides circuit
protection. The LT1533 is packaged
in the narrow 16-lead SO, and is
available in commercial and industrial grades.
The LT1533 allows the circuit
designer to add a switching regulator
to sensitive analog systems without
fear of introducing uncontrollable
noise and interference. The program-
mable operating frequency and switch
slew rates allow final tuning to occur
in the circuit, when the system is
running and interference problems
may first become apparent. In addition to providing a way to deal with
unforeseen problems, this flexibility
means that sacrifices in efficiency
will be limited to those needed for
proper system performance. The
LT1533 is the switching regulator of
choice for high performance analog
systems.
21
DESIGN IDEAS
LT1635 1A Shunt Charger
Most battery chargers comprise
nothing more than a series-pass
regulator with current limit. In solarpowered systems, you can’t count on
sufficient headroom to keep a series
regulator alive, so a shunt method is
preferred. A simple shunt battery
charger is shown in Figure 1. It consists of an op amp driving a shunt
transistor and ballast resistor, and is
built around an LT1635. This device
contains both an op amp and a reference, making it perfectly suited for
regulator and charger applications.
Operation is straightforward: the
battery voltage is sensed by a feedback divider composed of two 1M
resistors. The internal 200mV reference is amplified to 7.05V and
compared against the feedback. RT1
introduces a TC that accurately tracks
the battery’s correct charging voltage
by Mitchell Lee
over a wide temperature range.
Because RT1 is designed to compensate
for changes in battery temperature, it
should be located close to the battery
and as far as possible from the shunt
elements. When the battery charges
to 14.1V, the op amp output begins to
rise, turning on the Darlington shunt
and resisting further increases in voltage. Full panel power is divided equally
between the transistor and 7.5Ω
resistor when the battery is completely
charged. Don’t forget to provide adequate heat sinking and air flow for
up to 15W dissipation.
The charger is designed to handle
1A continuous, which is compatible
with a “20W” panel. There is no need
to disconnect or diode isolate the
charger during periods of darkness,
because the standby current is only
230µA—less than 10% of the self
discharge of even a small battery.
If a different or adjustable output
is desired, the feedback ratio can be
easily modified at the 1M divider.
14.1V is a compromise between an
aggressive charge voltage and a conservative float voltage. Given the cyclic
nature of insolation, allowing periodic charging at 14.1V is not
detrimental to Gelcell™ batteries. The
circuit in Figure 1 will work with
larger or smaller batteries than that
shown. As a rule of thumb, the panel
should be sized from 1W per 10Ah
battery capacity (a float charge under
good conditions with a good battery)
to 5W per 1Ah battery capacity (1 day
recharge of a completely discharged
battery under favorable conditions of
insolation).
Gelcell is a trademark of Johnson Controls, Inc.
DESIGN IDEAS
LT1635 1A Shunt Charger .......22
Mitchell Lee
Negative-to-Positive
Telecommunication Supply ..... 23
14.1V
Kurk Mathews
Send Camera Power and Video
on the Same Coax Cable ..........24
2A
100nF
Frank Cox
MUX the LTC1419
Without Software .................... 25
1M
3
1A SOLAR
ARRAY
+
Kevin R. Hoskins
Low Cost 3.3V to 1.xV 6 Amp
Power Supply .......................... 26
200mV
8
REF
1/2 LT1635
–
1 7.05V
2
–
220Ω
6
TIP121
12V, 5Ah
Gelcell
4
7.5Ω/10W
DALE HLM-10
1M
Short-Circuit-Proof Isolated
High-Side Switch .....................27
7
OA
1/2 LT1635
64.5k
Sam Nork
105Ω
Mitchell Lee
The LTC1590 Dual 12-Bit DAC
is Extremely Versatile .............28
+
2.43k
RT1
7.5k
Kevin R. Hoskins
12V Wall Cube to 5V/400mA DC/DC
Converter is 85% Efficient .......30
RT1 = THERM-O-DISC 1K752J
Steve Pietkiewicz
Figure 1. 1A shunt battery charger (IDARK = 230µA; VFLOAT = 14.1V)
Authors can be contacted
at (408) 432-1900
22
Linear Technology Magazine • August 1997
DESIGN IDEAS
Negative-to-Positive
Telecommunication Supply
An increasing number of telecommunication circuits require a positive
supply voltage derived from a –48V
input. The traditional approach to
negative-to-positive conversion has
been to use a buck-boost converter
(see Figure 1). Unfortunately, this
topology suffers drawbacks as the
power level and input-to-output voltage difference increases.
A more appropriate solution for
–48V to 5V conversion is shown in
Figure 2. The LT1680 is used to implement a forward converter with its
output referenced to the input common. Compared to the buck-boost
converter, switch current is reduced
by a factor of two and output capacitor ripple is reduced by a factor of five.
The LT1680 is referenced to –48V
and requires a 12V bias supply. The
12V is generated by using the RUN/
SHDN and a bootstrap winding on the
output inductor, L1. When input voltage is first applied, R1 begins charging
C1. As C1 charges, Q1 is held on by
R2, shorting R3. R4 and R5 form a
voltage divider that holds the RUN/
SHDN pin below its 1.25V threshold
until the 12VIN pin reaches approximately 14V. Once out of standby, Q1
is turned off by Q2, reducing the run
threshold to approximately 9V and
allowing C1 time to discharge slightly
before the overwinding on L1 takes
over. The only remaining issue is feedback. Q3 translates the output voltage
to a current, which flows to the VFB
pin.
The LT1680’s unique differential
current sense amplifier has an input
common mode range of –0.3V to 60V.
T1 = COILTRONICS VP5-1200, 1:1:1:1:1:1
(SIX WINDINGS, EACH 77 µH)
L1 = PHILIPS EFD20-3F3-E63-S CORE SET (A l = 63nH/T2)
OUTPUT 18T BIFILAR 22AWG,
BIAS 54T BIFILAR 32 AWG
* = SANYO CV-GX
by Kurk Mathews
If VIN is expected to exceed 60V, the
sense resistor could be relocated in
the main FET’s source and the input
capacitors’ voltage increased. Because
the forward converter is fundamentally an isolated topology, an
optocoupler and reference could be
added to provide isolation between
the input and output of the supply.
+VOUT
+
+
–VIN
DI_1680_01.eps
Figure 1. Buck/boost converter
33Ω
1.5nF
T1
L1, OUTPUT
20µH
INPUT
COM
+
220µF* 220µF*
35V + 35V
24k
5V/6A
1k
1µF
63V
300pF
24k
+
33Ω
MBR2045CT
1.5nF
220µF* 220µF*
35V + 35V
R1
24k
MBR0520LT1
+
50Ω
1W
0.015Ω
1W
IRF640
–48V
330µF
6.3V
SANYO
OSCON
10Ω
4.22k
Q3
2N5401
R4
78.7k
15
SYNC
9
10
13
S– GATE
S+
11 RUN/SHDN
1
SL_ADJ
BAV21
L1,
BIAS
R2
1M
C1
220µF
35V
+
14 12V
IN
LT1680
VFB
0.1µF
R5
7.5k
5VREF
CT
IAVG
16
2
3
Q1
2N7000
20k
Q2
2N3904
16k
SS
4
VC
2.2nF
7
SGND PGND VREF
5
6
12
8
0.22µF
0.1µF
R3
4.75k
1µF
1nF
20k
1.2k
0.1µF
1k
Figure 2. –48V to 5V Telecommunication supply
Linear Technology Magazine • August 1997
23
DESIGN IDEAS
Send Camera Power and Video
on the Same Coax Cable
by Frank Cox
Because remotely located video
surveillance cameras do not always
have a ready source of power, it is
convenient to run both the power and
the video signal through a single coax
cable. One way to do this is to use an
inductor to present a high impedance
to the video and a low impedance to
the DC. The difficulty with this method
is that the frequency spectrum of a
monochrome video signal extends
down to at least 30Hz. The composite
color video spectrum goes even lower,
with components at 15Hz. This implies
a rather large inductor. For example,
a 0.4H inductor has an impedance of
only 75Ω at 30Hz, which is about the
minimum necessary. Large inductors
have a large series resistance that
wastes power. More importantly, large
inductors can have a significant
amount of parasitic capacitance and
stand a good chance of going into self
resonance below the 4MHz video
bandwidth and thus corrupting the
signal. The circuit shown in Figure 1
takes a different approach to the problem by using all active components.
The circuitry at the monitor end of
the coax cable supplies all the power
to the system. U1, an LT1206 current
feedback amplifier, forms a gyrator or
synthetic inductor. The gyrator isolates the low impedance power supply
from the cable by maintaining a reasonably high impedance over the video
bandwidth while, at the same time,
contributing only 0.1Ω of series resis-
C2
4.7µF
TANT
C3
1000µF
+
12V
CAMERA
U3
OUT LT1086CT-12 IN
+
C5
0.1µF
tance. This op amp needs to have
enough bandwidth for video and sufficient output drive to supply 120mA
to the camera. The selected part has
a guaranteed output current of 250mA
and a 3dB bandwidth of 60MHz, making it a good fit. Because the video
needs to be capacitively coupled, there
is no need for split supplies; hence a
single 24V supply is used. The 24V
supply also gives some headroom for
the voltage drop in long cable runs.
The camera end has an LT1086
fixed 12V regulator (U3) to supply
12V to a black and white CCD video
camera. U4, an LT1363 op amp, supplies the drive for Q1, a fast, high
current transistor. Q1, in turn, modulates the video on the 20V DC. The
Q1
ZETEX ZTX749
C6
1000µF
+
R4
2k
100' RG58U/U
20V DC
R5
10k
+
R1
10k
C1
20µF
3
R2
10k
2
C4
1000µF
7
+
U4
LT1363
–
+
VIDEO
OUT
6
4
R6
75Ω
C7
1000µF
R3
1k
562Ω
24V
24V
24V
C10
1000µF
R7
2.32k
0.1µF
C9
20µF FILM
R9
500k
R8
11.5k
R12
10k
4.7µF
FILM
3
R13
10k
24V
2
1
2
+
7
6
U2
LT1363
–
R17
75Ω
4
R15
280Ω
5
3
6
TO
MONITOR
R14
562Ω
7
U1
LT1206CT
–
C13
100µF
R10
0.1Ω
4
+
0.1µF
+
4.7µF
TANT
+
+
R16
280Ω
C11
51pF
NC
+
C12
1000µF
R11, 100Ω
DI_VID_01.eps
Figure 1. Circuit transmits video and 12V power on the same coax cable
24
Linear Technology Magazine • August 1997
DESIGN IDEAS
collector of Q1 is the input to the 12V
regulator. This point is AC ground
because it is well bypassed as required by U3. U1 is set up to deliver
20V to the cable. Because the 12V
regulator in the camera end needs
1.5V of dropout voltage, the balance
of 6.5V can be dropped in the series
resistance of the cable. The output of
the LT1206 is set to 20V to give headroom between the supply and the
video.
U2, another LT1363 video-speed
op amp, receives video from the cable,
supplies some frequency equalization
and drives the cable to the monitor.
Equalization is used to compensate
for high frequency roll off in the camera cable. The components shown
(R16, C11) gave acceptable monochrome video with 100 feet of RG58
B/U cable.
MUX the LTC1419 Without Software
by Kevin R. Hoskins
The circuit shown in Figure 1 uses
hardware instead of software routines to select multiplexer channels
in a data acquisition system. The
circuit features the LTC1419 800ksps
14-bit ADC. It receives and converts
signals from a 74HC4051 8-channel
multiplexer. Three of the four output
bits from an additional circuit, the
74HC4520 dual 4-bit binary counter,
are used to select a multiplexer channel. A logic high power -on or
processor-generated reset is applied
to the counter’s pin 7.
After the counter is cleared, the
multiplexer’s channel selection input
is 000 and the input to channel 0 is
applied to the LTC1419’s S/H input.
The channel-selection counter is
clocked by the rising edge of the convert start (CONVST) signal that
initiates a conversion. As each
CONVST pulse increments the
counter from 000 to 111, each multiplexer channel is individually selected
and its input signal is applied to the
5V
AIN 1
AIN 2
AIN 3
AIN 4
AIN 5
AIN 6
AIN 7
14
15
12
1
5
2
4
+
0.1µF
VCC
0
16
0.1µF
1
COM
2
1
3
1µF
3
INH
4
GND
5
VSS
A
B
2
6
3
8
4
+
10µF
6
7
0.1µF
5
6
7
0.1µF
C
7
8
9
74HC4520
14
13
12
11
10
3
4
5
6
–5V
1Q0 1Q1 1Q2 1Q3
1
1CLK
2Q3
2
1CE
2Q2
7
1CLEAR
2Q1
15
2CLEAR
2Q0
16
VCC
2CE
2CLK
9
10
11
12
13
14
0
+
AIN
AVDD
–
AIN
DVDD
VREF
VSS
COMP
BUSY
AGND
CS
D13 (MSB)
CONVST
D12
RD
D11
SHDN
D10
D0
D9
D1
D8
D2
D7
D3
D6
D4
DGND
D5
28
fSAMPLE = 100ksps
fIN = 1.19kHz
VIN = ±2.5V
–20
27
26
–40
25
BUSY
24
23
CONVERT
CONTROL
22
21
20
–60
–80
–100
–120
19
–140
18
0
17
10
20
30
40
50
INPUT FREQUENCY (kHz)
16
15
DI_MUX_02.EPS
DI_MUX_01.EPS
5V
GND
8
0.1µF
LTC1419
AMPLITUDE (dB)
AIN O
10µF
+
74HC4051
13
–5V
10µF
5V
LTC1419. After each of the eight channels has been selected, the counter
rolls over to zero and the process
repeats. At any time, the input multiplexer channel can be reset to 0 by
applying a logic-high pulse to pin 7 of
the counter.
This data acquisition circuit has a
throughput of 800ksps or 100ksps/
channel. As shown in Figure 2, the
SINAD is 76.6dB for a full-scale ±2.5V,
1.19kHz sine wave input signal.
0.1µF
DATA 0–13
Figure 2. FFT of the MUXed
LTC1419’s conversion of a full-scale
1.19kHz sine wave
CLEAR
COUNT
Figure 1. This simple stand-alone circuit requires no software to sequentially sample and
convert eight analog signal channels at 14-bit resolution and 100ksps/channel.
Linear Technology Magazine • August 1997
25
DESIGN IDEAS
Low Cost 3.3V to 1.xV 6 Amp
Power Supply
As voltage requirements for microprocessors drop, the need for high
power DC/DC conversion from a 3.xV
supply to a lower voltage keeps growing. The LTC1430 is a very attractive
choice for such DC/DC applications,
due to its low cost, high efficiency and
high output power capability. However, there are two problems: first,
3.xV does not provide enough gate
drive to ensure low RDS(ON) using external logic-level FETs; and second,
the LTC1430 has a 4V minimum input requirement. These obstacles are
both overcome by using an LTC15175 regulated charge pump to generate
the input voltage for the LTC1430.
The circuit shown in Figure 1 uses
the LTC1430 to produce a synchronous 3.3V to 1.9V step-down DC/DC
converter. The circuit achieves 90.5%
efficiency at 3 amps of output current
and has a 6 amp maximum output
capability. (Refer to the LTC1430 data
sheet for detailed description of
LTC1430-based designs). Power for
the LTC1430 is derived from the output of the LTC1517-5.
The LTC1517-5 is a switched
capacitor charge pump available in a
tiny, 5-pin SOT-23 package. The part
uses Burst Mode operation to generate
a 5V output from a 2.7V to 5V input.
It achieves regulation by sensing the
output voltage via an internal reference, comparator and resistor divider
(see Figure 3). When the output has
drooped below the lower trip point of
the comparator, the charge pump is
enabled, boosting VOUT back above
the upper trip point. The LTC1517-5
also contains thermal-shutdown and
short-circuit protection.
The regulated 5V supply powers
the internal circuitry of the LTC1430
and ensures that the LTC1430 can
provide adequate gate drive to the
external N-channel FETs. With
insufficient gate drive, output power
and efficiency will be significantly
reduced due to high RDS(ON) of the
FETs. In this circuit, typical supply
100
EFFICIENCY (%)
90
2
+
5
1
LTC1517-5
3
4
C3
0.22µF
C6 TO C9*
330µF
6.3V
C10
×4
0.1µF
R2
24k
C2
Y5V CERAMIC
10µF
D1
BAT54
C5
1µF
ON OFF
R1
100Ω
Q2
Si4410
R3
1k
C4
0.1µF
1
2
3
4
5
6
7
8
LTC1430CS
16
G1
G2
15
PVCC1
PVCC2
14
PGND
VCC
13
IFB
GND
12
–
IMAX
SENSE
11
FB
FREQSET
10
SENSE +
COMP
9
SHDN
SS
C12
0.1µF
80
70
60
40
0.1
1
LOAD CURRENT (A)
10
1517_02.EPS
Figure 2. Efficiency curve for Figure 1’s
circuit
current drawn by the LTC1430 is
between 25mA and 30mA, the vast
majority of which is needed to charge
and discharge the external FETs.
Because the LTC1517-5 has a maximum effective output impedance of
50Ω, this current can be comfortably
supplied from a 3.3V input. If the
input voltage drops to 3V or lower, the
LTC1517-5 output may also drop.
However, with the FETs shown in
Figure 1, the LTC1517-5 will provide
a 4.5V minimum supply to the
LTC1430 at input voltages down to
3V.
C11
1µF
L1
2.4µH, 8A
SUMIDA
CDRH127-2R4
Q1
Si4410
5V
VIN = 3.3V
VOUT = 1.9V
50
VIN
3.3V
C1
Y5V CERAMIC
3.3µF
by Sam Nork
D2
MBRS120
C16
0.018µF
R5
4.99K
1%
VOUT
1.9V
6A
+
R6
10K
1%
C17 TO C21 *
330µF
6.3V
×5
R4
5.2k
C13
390pF
C14
0.012µF
+
C15
10µF
10V
1517 TA03
*AVX TPS TANTALUM
Figure 1. 3.3V to 1.9V/6A power supply
26
Linear Technology Magazine • August 1997
DESIGN IDEAS
Pulling the SHDN pin on the
LTC1430 low will shut down the power
supply. Q1 and Q2 will be forced off
and the LTC1430 quiescent current
will drop to 1µ A. Although the
LTC1517-5 does not have a shutdown
feature, the no-load operating current
is an extremely low 6µA. This keeps
the overall shutdown current below
10µA plus external FET leakage. (For
further reductions in shutdown current, an 8-pin LTC1522 may be used
in place of the LTC1517-5; the
LTC1522 is the same as an LTC1517-5
with shutdown.) The additional
LTC1517-5 circuitry will not take up
much board space. The entire circuit
consumes only 0.045 in2.
C1
0.22µF
C1 –
VIN
C1 +
VOUT
CHARGE PUMP
CIN
3.75M
COUT
+
800kHz
OSC
1.25M
–
THERMAL
SHDN
1.25V
REF
LTC1517-5
1517 BD
Figure 3. LTC1517-5 simplified block diagram
Authors can be contacted
at (408) 432-1900
Short-Circuit-Proof Isolated
High-Side Switch
Figure 1 shows a MOSFET switch,
driven by the LTC1177-5 2.5kVRMS
isolator. This device allows a logic
signal to control a power MOSFET
and provides complete galvanic isolation. The device includes an internal
current limiting circuit, but at higher
voltages limiting the current is just
not enough for effective protection of
the MOSFET. Foldback (shown on the
LTC1177 data sheet) helps, but the
part has trouble starting certain types
of loads when foldback current limiting is used. The circuit shown here
latches off in an overcurrent condition and is restarted by cycling the
logic input.
Q1 and Q2 form an SCR with a
holding current of less than 100nA. If
the load current exceeds approximately 1A, the SCR fires, shorting the
MOSFET gate to source. The LTC1177
output current (about 7µA) is more
than adequate to hold the SCR on
Linear Technology Magazine • August 1997
indefinitely. The circuit resets when
the logic input briefly cycles off.
Inductive loads present a special
problem. If the load creeps up on the
overcurrent threshold and fires the
SCR, the load’s inductance will carry
the MOSFET source far below ground,
which could destroy the MOSFET.
Diode D1 clamps the gate at ground,
5V
by Mitchell Lee
turning the MOSFET back on, and
safely dissipates the stored magnetic
energy in the MOSFET.
As shown the output rise time is
about 2ms, allowing the circuit to
successfully charge capacitors of up
to 100µF. Increase C1 proportionately to handle higher value load
capacitors.
2.5kV
ISOLATION BARRIER
24V
OFF
100Ω
ON
VIN
C1
10nF
OUT
LTC1177
G1
SENSE
G2
Q2
2N3904
10M
D1
1N914
Q1
2N3906
MTD3055EL
20M
10M
0.5Ω
1W
LOAD
Figure 1. Short-circuit protected, isolated high-side switch
27
DESIGN IDEAS
The LTC1590 Dual 12-Bit DAC
is Extremely Versatile
by Kevin R. Hoskins
0.1µF
5V
VIN A
±10V
15V
1
16
2
0.01µF
33pF
VREF A RFB A
DATA IN
SERIAL CLOCK
CHIP SELECT/
DAC LOAD
DATA OUT
CLEAR
13 DIN
14 CLK
11 CS/LD
4 DOUT
15 CLR
7 AGND
24-BIT SHIFT REGISTER AND LATCH
CMOS multiplying DACs make versatile building blocks that go beyond
their basic function of converting digital data into analog signals. This
Design Idea details some of the other
circuits that are possible when using
the LTC1590 dual, serially interfaced
12-bit DAC.
The circuit shown in Figure 1 uses
the LTC1590 to create a digitally controlled attenuator using DACA and a
programmable gain amplifier (PGA)
using DACB. The attenuator’s gain is
set using the following equation:
2
–
OUT2A 4
3
+
DACA
8
1
1/2 LT1358
VOUT A
VOUT = –VIN D
2n
LTC1590
n
OUT2B 5
5
+
OUT1B 6
6
–
DACB
VOUT = –VIN 2
D
7
VOUT B
1/2 LT1358
VREF B RFB B
10 DGND
VOUT = –VIN D
2n
OUT1A 3
0.01µF
4
33pF
9
8
DI1590_01.EPS
= output voltage
= input voltage
= DAC resolution in bits
= value of code applied
to DAC
The attenuator’s gain varies from
4095/4096 to 1/4096. A code of 0
can be used to completely attenuate
the input signal.
The PGA’s gain is set using the
following equation:
0.1µF
The gain is adjustable from 4096/
4095 to 4096/1. A code of 0 is meaningless, since this results in infinite
gain and the amplifier operates open
loop. With either configuration, the
attenuator’s and PGA’s gain are set
with 12 bits accuracy.
Further modification to the basic
attenuator and PGA is shown in Figure 2. In this circuit, DAC A ’s
attenuator circuit is modified to give
the output amplifier a gain set by the
ratio of resistors R3 and R4. The
28
1k
15k
2
VREF A RFB A
DATA IN
SERIAL CLOCK
CHIP SELECT/
DAC LOAD
DATA OUT
CLEAR
13 DIN
14 CLK
11 CS/LD
4 DOUT
15 CLR
7 AGND
10 DGND
15V
R4
15k
1
16
n
= output voltage
= input voltage
= DAC resolution in bits
= value of code applied
to DAC
VIN A
±10V
5V
VOUT = –VIN 2
D
where VOUT
VIN
n
D
–15V
Figure 1. Driving DACA’s reference input (VREF) and tying the feedback resistor (RFB) to the op
amp’s output creates a 12-bit accurate attenuator. Reversing the VREF and RFB connections
configures DACB as a programmable-gain amplifier.
24-BIT SHIFT REGISTER AND LATCH
where VOUT
VIN
n
D
VIN B
±10V
R3
1k
0.01µF
33pF
2
–
OUT2A 4
3
+
OUT2B 5
5
+
OUT1B 6
6
–
OUT1A 3
DACA
8
1/2 LT1358
1
VOUT A
VOUT = –VIN 16D
2n
LTC1590
DACB
1/2 LT1358
VREF B RFB B
9
8
15k
4
n
VOUT = –VIN 2
16D
7
VOUT B
0.01µF
33pF
DI1590_02.EPS
R1
1k
1k
R2
15k
–15V
VIN B
±10V
Figure 2. Modifying the basic attenuator and PGA creates gain for the attenuator (R3 and R4)
and attenuation at the PGA’s input (R1 and R2).
Linear Technology Magazine • August 1997
DESIGN IDEAS
15V
10k
10k
0.01µF
VIN A
10k
2
3
–
8
U2A
1/2 LT1358
1
+
0.1µF
5V
15V
15V
0.01µF
16
1
2
0.01µF
3
13 DIN
DATA IN
14 CLK
SERIAL CLOCK
11 CS/LD
CHIP SELECT/
DAC LOAD
4 DOUT
DATA OUT
15 CLR
CLEAR
7 AGND
24-BIT SHIFT REGISTER AND LATCH
VREF A RFB A
OUT2A 4
–
8
U3A
1/2 LT1358
3
2
1
+
8
+
U4A
1/2 LT1358
RI
OUT2B 5
5
DACB
OUT1B 6
6
+
U3B
1/2 LT1358
–
4
7
RI
6
–
5
+
0.01µF
D
2n+1 • π • RI • CI
CI
U4B
1/2 LT1358
4
6
VOUT A
CI
fC =
VREF B RFB B
5
1
–
U1 LTC1590
9
10k
2
DACA
10 DGND
VIN B
OUT1A 3
7
VOUT B
0.01µF
8
+
U2B
1/2 LT1358
–
–15V
7
–15V
4 0.01µF
10k
10k
DI1590_03.EPS
–15V
Figure 3. This LTC1590-controlled dual single-pole lowpass filter uses RI and the DAC’s input code to create an effective resistance that sets the
integrator’s time constant and, therefore, the circuit’s cutoff frequency.
equation for this attenuator with output gain is
VOUT = –VIN 16D
2n
With the values shown, the
attenuator’s gain has a range of
–1/256 to –16. This range is easily
modified by changing the ratio of R3
and R4. In the other half of the circuit,
an attenuator has been added to the
input of DACB, configured as a PGA.
The equation for this PGA with input
attenuation is
n
VOUT = –VIN 2
16D
This sets the gain range from effectively –1/16 to –256. Again, this range
Linear Technology Magazine • August 1997
can be modified by changing the ratio
of R1 and R2.
The LTC1590 can also be used as
the control element that sets a lowpass filter’s cutoff frequency. This is
shown in Figure 3. The DAC becomes
an adjustable resistor that sets the
time constant of the integrator formed
by U4 and CI. With the integrator
enclosed within a feedback loop, a
lowpass filter is created.
The cutoff frequency range is a
function of the DAC’s resolution and
the digital data that sets the effective
resistance. The effective resistance is
n
RREF = RI 2
D
Using this effective resistance, the
cutoff frequency is
fC =
D
2n+1 • π • RI • CI
The cutoff frequency range varies
from 0.0000389/RC to 0.159/RC. As
an example, to set the minimum cutoff frequency to 10Hz, make RI =
8.25k and CI = 470pF. At an input
code of 1, the cutoff frequency is
10Hz. The cutoff frequency increases
linearly with increasing code,
becoming 40.95kHz at a code of 4095.
Generally, as the code changes by ±1
bit, the cutoff frequency changes by
an amount equal to the frequency at
D = 1. In this example, the cutoff frequency changes in 10Hz steps.
29
DESIGN IDEAS
12V Wall Cube to 5V/400mA DC/DC
Converter is 85% Efficient by Steve Pietkiewicz
The ubiquitous 12V wall cube,
power source of countless electronic
products, generates an unregulated
DC voltage between 8V and 18V,
depending on line voltage and load. If
you use a linear regulator to drop the
voltage to 5V, a 400mA load means
the linear regulator must dissipate
5W under worst-case conditions. To
deal with this heat, you must provide
adequate heat sinking, increasing
your product’s size and weight. Additionally, the heat is sometimes
objectionable to customers. These
factors can negate the cost advantage
of a linear regulator. Figure 1’s circuit, a negative buck converter,
delivers 5V at loads up to 400mA from
a 7V–25V input with peak efficiency
of 85%, eliminating the need for a
heat sink. Since the LT1307B (U1) is
intended for use with a low input
voltage, Q1 and Q2 are used to make
a simple preregulator, providing 1.9V
for U1’s VIN pin. The IC switches at
600kHz, allowing a low cost 22µH
inductor and 10µF ceramic output
capacitor to be used. Q3 is needed to
level shift the output voltage because
U1’s feedback pin is referenced to the
negative input. Output ripple measures 10mVP-P at a load of 400mA.
The circuit’s efficiency is detailed in
Figure 2, and response to a load step
from 150mA to 300mA is shown in
Figure 3. Input bypass capacitor C1
sees worst-case RMS ripple current
equal to one-half the output current
and should have an ESR of less than
0.5Ω. Take care during construction
to keep R1–R3 and Q3 close to U1’s
FB pin and away from the SW pin to
prevent unwanted coupling. Use a
ground plane and keep traces for the
power components short and direct.
Although it might seem unsettling
that the negative side of the wall cube
is not grounded, remember that the
9V wall cube floats. The circuit merely
regulates the negative side, rather
than the more conventional positive
side.
5V
400mA
+
12V
UNREGULATED
SUPPLY
–
C2
10µF
CERAMIC
10k
Q2
2N3904
1N5818
3
6
SW
U1
LT1307B
FB
30k
Q1
2N3904
VC
1
1µF
CERAMIC
10k
L1
22µH
VIN
SHDN
5
Q3
2N3906
2
GND
4
30k
R1
12.1k
1%
R2
42.2k, 1%
R3
100k
+
C1
33µF
25V
1000pF
L1 = SUMIDA CD54-220
DI_ADAP_01.EPS
Figure 1. This negative buck converter delivers 5V at 400mA from a 7V–25V input.
90
88
VIN = 8V
86
EFFICIENCY (%)
84
VOUT
0.5V/DIV
VIN = 12V
82
VIN = 18V
80
78
IL1
0.5A/DIV
ILOAD
0.3A/0.15A
76
74
72
70
50
100
150 200 250 300
LOAD CURRENT (mA)
350
400
50µs/DIV
DI_ADAP_03.eps
DI-ADAP_02.EPS
Figure 2. Efficiency peaks at 85%; it is above
80% over an input range of 8V–18V.
30
Figure 3. Load-step response; the load changes from
150mA to 300mA.
Linear Technology Magazine • August 1997
DESIGN INFORMATION
Understanding and Applying
Voltage References (Part Two)
by Mitchell Lee
Board Leakage
A new specter has entered the field of
references: board leakage caused by
the residues of water-soluble flux.
The effect is not unlike that produced
by the sticky juice extravasated from
a ruptured electrolytic capacitor.
Leakage from ground, supply rails
and other circuit potentials into NC,
trim and other sensitive pins through
conductive flux residues will cause
output voltage shifts. Even if the leakage paths do not shift the reference
out of spec, external leakage can
manifest itself as long-term output
voltage drift, as the resistance of the
flux residue changes with shifts in
relative humidity and the diffusion of
external contaminants. Water-soluble
flux residues must be removed from
the board and package surfaces, or
completely avoided. In one case, the
author observed an LT1009 shifted
out of spec by a gross leakage path of
approximately 80kΩ between the trim
pin and a nearby power supply trace.
The leakage was traced to watersoluble flux.
Figure 8 shows how a good reference can go bad with only a very small
leakage. A hypothetical industrial control board contains an LT1027A
producing 5V for various data acquisition circuits. A nearby trace carries
24V. Just 147MΩ leakage into the
noise filtering pin (NR) causes a typical device to shift +200ppm, and out
of spec. Clearly, a 24V circuit trace
doesn’t belong anywhere near a 0.02%
reference. This example is oversimplified but clearly demonstrates the
potential for disaster.
A tightly packed circuit board may
leave no choice but to agglomerate
incompatible traces. In this case, use
a guard ring to eliminate reference
shift (see Figure 9). The output of the
reference is divided down to 4.4V,
equal to the potential on the NR pin,
and used to bias a guard ring encircling the trace connecting NR to the
noise filter capacitor. This reduces
the effect of board leakage paths by
more than two orders of magnitude,
shunting the errant leakage away from
the guarded traces.
Trim-Induced
Temperature Drift
About half of LTC’s reference offerings include a pin for external
(customer) trimming. Trimming may
be necessary to calibrate the system,
but it can also adversely affect the
tempco of the reference. For example,
in the LT1019 bandgap reference,
external trim resistors won’t match
the tempco of the internal resistors.
The mismatch causes a small
(1ppm/°C) worst-case shift in the
output voltage tempco, as explained
on the data sheet. The LT1021-5 and
LT1236-5 standard trim circuit can
be modified, as shown in Figure 10, to
prevent upsetting the references’
VIN
LT1027
VIN
1µF
MYLAR
5V
GUARD
RING
NR
REFACC_08.eps
5V
VOUT
GND
GND
30k
Linear Technology Magazine • August 1997
Burn-in can help “relax” a stuffed
board, but additional mechanical
stress may be introduced when the
board is mounted into the product.
Stress has a directly measurable effect
on reference output. If the stress
changes over a period of time, it may
manifest itself as unacceptable longterm drift. Circuit boards are not
perfectly elastic, so bending forces
may cause permanent deformation
and a permanent step-change in reference output voltage. Devices in
OUT
LT1236-5
IN
OR
LT1021-5
TRIM
GND
VOUT
R1
27k
R2
50k
1N4148
220k
REFACC_09.eps
Figure 8. Board leakage can wreak havoc with
a precision reference. Here, a 147MΩ leakage
path to 24V pushes the 5V output out of spec.
Board Stress
147MΩ
147MΩ
VOUT
Most manufacturers of high-accuracy
systems run their products through a
burn-in procedure. Burn-in solves
two problems at once: it relieves
stresses built into the reference and
circuit board during assembly and it
ages the reference beyond the highest
long-term drift region, which occurs
when power is first applied to the
part. A typical burn-in procedure calls
for operating the board at 125°C
ambient for 168 hours. If the main
concern is stress relief, a shorter,
unpowered burn-in cycle can be used.
10V
10V
LT1027
Burn-In
24V
24V
NR
inherently low temperature coefficients. Trimming the LT1027 has little
effect on the output voltage tempco,
and it needs no special consideration.
Always check the reference data sheet
for specific recommendations.
Figure 9. Adding a guard ring protects against
errant leakage paths.
REFACC_10.eps
Figure 10. The LT1021 or LT1236 output trim
is made temperature insensitive by the
addition of a diode and a resistor.
31
DESIGN INFORMATION
160
9"
LONGEST DIMENSION
OUTPUT DEVIATION (ppm)
ORIGINAL CIRCUIT BOARD
7"
120
S8
LONGEST
AXIS
80
SLOTTED CIRCUIT BOARD
40
SLOTTED AREA
APPROXIMATELY
1/2 INCH BY 1/2 INCH
4ppm = 10µV = METER RESOLUTION
0
0
1
10
20
30
DEFLECTION NUMBER
40
MSOP
REFACC_12.eps
Figure 12. Isolating stress by slotting the
circuit board reduces reference variations by
more than an order of magnitude.
2
REFACC_13.eps
3
4
REFACC_11.eps
Figure 11. Reference sensitivity to stress was
evaluated by assembling devices on a 7" × 9"
circuit board and flexing, as shown in steps
1–4.
metal (TO-5 and TO-46) packages are
largely immune to board stress, owing
to the rigidity of the package and the
flexibility of the leads. Plastic and
surface mount packages are another
matter.
Board stress effects are easily
observed by monitoring the output of
a reference while applying a bending
force to the board. A controlled
experiment was performed to measure the effect of board stress on an
LT1460CS8-2.5 surface mount reference. Devices were mounted in the
center of 7" × 9" rectangular boards,
as shown in Figure 11. The boards
were then deflected out-of-plane 18
mils per inch, as shown in steps 1
through 4. Figure 12 shows the net
effect on the output of one representative sample measured over eight
cycles of flexure.
The original board showed about
60ppm peak-to-peak shift. The board
was then slotted on a vertical mill,
forming a 0.5" × 0.5" tab with the
reference located in its center (also
illustrated in Figure 11). The test continued with the slotted configuration,
and the output voltage variations were
reduced to ±1 count (10µV) on the
meter, or approximately 4ppm peak32
to-peak. This represents a tenfold
improvement in stress-induced output voltage shift.
Several other techniques can be
employed to minimize this effect, without resorting to a milled board.
Anything that can be done to restrict
the board from bending is helpful. A
small, thick board is better than a
large, thin board. Stiffeners help
immunize the board against flexure.
Mount the circuit board with grommets, flexible standoffs or card-cage
style so that minimal force is applied
to the mounting holes and board.
Part placement and orientation are
just as important. If a board is
squeezed from opposite edges, the
bending force tends to concentrate in
a line down the center. Locate the
reference away from the middle of the
board. Since the longer side of a board
is more flexible than the shorter, locate
the reference along the shorter edge.
These recommendations are generalities; the placement, mounting
method and orientation of other components and assemblies on the circuit
board will influence the mechanical
strengths and weaknesses of the circuit board.
Bench tests indicate that the
strongest axis for plastic packages is
along the shorter dimension of the
body of the plastic. Figure 13 shows
the correct orientation for surface
mount parts. Note that the part’s
longest axis is placed perpendicular
to that of the circuit board. The devices in Figure 13 are shown in the
center of the board for illustrative
Figure 13. Arranging the longest axes of the
board and package in perpendicularity
minimizes stress-induced output changes.
purposes only; comments about
placement still apply.
In spite of all precautions, extraneous effects may adversely affect the
reference’s resistance to board stress.
Watch out for adhesives and solder
and flux debris under the package.
These will create pressure points and
induce unpredictable stresses in the
package. If a board has been subjected to a high bending force, some of
the glass fibers and layers may break
or shear apart, permanently weakening the board. Subsequent bending
forces will concentrate their stress at
points thus weakened.
Figure 14 shows various schemes
for routing stress-relief slots on a
circuit board, along with optimum
package orientation. Note that the
longest axis of the reference is aligned
with the tab, not the shortest axis of
the circuit boar d. This is in
(c)
(a)
(b)
(d)
(e)
REFACC_14.eps
Figure 14. Slotting the area around the
reference can help isolate it from board stress
if properly applied (see text).
Linear Technology Magazine • August 1997
DESIGN INFORMATION
OUTPUT VOLTAGE NOISE (20µV/DIV)
LT1021-7 (TO-5 PACKAGE)
f = 0.01Hz TO 10Hz
R3
249k
0.1%
–
FOAM CUP
REMOVED
1/2
LT1495
ZTX214C
2XAAA
ALKALINE
CELLS
0
2
4
6
8
TIME (MINUTES)
10
R4
24kΩ
5%
+
+
20µV
1/2
LT1495
LT1634A-1.25
12
1µA
R2
1.00MΩ
0.1%
COM
–
R1
200kΩ
0.1%
REFACC_16.eps
1.5V
R1, R2, R3 = MAR5 SERIES
IRC (512) 992-7900
REFACC_15.eps
Figure 16. This pocket reference operates for five years on one set of AAA cells.
Figure 15. Air turbulence induces low
frequency noise and compromises reference
accuracy.
Temperature-Induced Noise
anticipation of flexing forces transmitted into the tab. The best
orientation for the tab is in line with
the longest axis of the board as in (b),
(c) and (d). Bending forces along the
weaker (longer) axis of the board could
be coupled into (a) and (e). Note that
the ICs are aligned to resist this
force. Use configuration (c) when the
part is located along the longer edge
of the board, and (d) when it is located along the shorter edge. Use (b)
when the part is not located along
any edge.
Even though references operate on
very meager supply currents, dissipation in the reference is enough to
cause small temperature gradients in
the package leads. Variations in
thermal resistance, caused by uneven
air flow, lead to differential lead
Table 3. Guaranteed supply current (mA) over temperature
Part
Bandgap
LT1004
LT1009
Buried
Zener
Mode***
1.25V
2.5V
4.5V
5.0V
✓
shunt
0.01
0.02
✓
shunt
✓
series
LT1019A
1.5
1.5
1.5
1.5
1.3
1.3
1.3
1.3
LT1021
✓
series
1.5
LT1027
✓
series
2.8
shunt
0.6
✓
LT1031
LT1034
✓
LT1236
LT1460
✓
series
*
shunt
✓
series
✓
series
✓
shunt
LT1634
1.5
2.0
2.0
0.02
0.02
0.165
0.1*
1.5
1.5
0.165
0.165
0.012
LT1634A
LTZ1000
10V
0.4
LT1019
LT1029
7.0V
0.012
✓
shunt
1.1**
***The LT1034 dual reference includes both a bandgap and a buried Zener
***Does not include heater current; recommended Zener current 5mA
***Current for shunt references is minimum operating current;
***for series references it is maximum quiescent current.
Linear Technology Magazine • August 1997
33
DESIGN INFORMATION
Table 4. Guaranteed percentage initial accuracy at 25˚C
Part
Bandgap
LT1004
Buried
Zener
Mode
1.25V
2.5V
✓
shunt
0.32
0.81
LT1009
✓
shunt
0.2
LT1019
✓
series
series
✓
LT1019A
4.5V
5.0V
0.2
0.2
0.2
0.2
0.05
0.05
0.05
0.05
LT1021B
1.0
✓
LT1021C
series
1.0
LT1027A
0.02
LT1027B
0.05
✓
0.7
0.05
LT1021D
LT1027C
7.0V
0.5
0.05
0.7
0.5
0.05
series
LT1027D
0.05
LT1027E
0.1
LT1029
1.0
✓
shunt
LT1029A
0.2
LT1031B
0.05
✓
LT1031C
series
0.1
LT1031D
LT1034
10V
0.2
✓
*
shunt
✓
series
1.2
1.6
LT1236A
LT1236B, C
4.3, –2.9
0.5
0.5
0.1
0.1
LT1460A
0.075
0.075
0.075
LT1460B, C, D
0.1
0.1
0.1
0.125
0.125
0.125
LT1460F
0.125
0.15
0.15
LT1460G
0.25
0.25
0.25
LT1460E
LT1634,A
LTZ1000
✓
series
✓
shunt
✓
0.1
shunt
4.2, –2.8
*The LT1034 dual reference includes both a bandgap and a buried Zener reference
34
Linear Technology Magazine • August 1997
DESIGN INFORMATION
Table 5. Temperature coefficient (ppm/˚C)
Buried
Zener
Part
Bandgap
Mode
LT1004
✓
shunt
LT1009
✓
shunt
LT1019
✓
series
LT1019A
Temperature
Range
0˚C–70˚C
–55˚C–125˚C
0˚C–70˚C
–55˚C–125˚C
0˚C–70˚C
–40˚C–85˚C
1.25V
75**
75**
2.5V
75**
75**
25
35
20
20
4.5V
5.0V
20
20
20
20
20
20
–55˚C–125˚C
25
25
25
25
0˚C–70˚C
5
5
5
5
–55˚C–125˚C
10
10
10
10
LT1021B
5
✓
LT1021C
series
TMIN≤TJ≤TMAX
20
LT1027A
2
LT1027B
2
✓
series
TMIN≤TJ≤TMAX
5
LT1027E
7.5
✓
shunt
LT1029A
20
0˚C–70˚C
34
–55˚C–125˚C
40
TMIN≤TJ≤TMAX
20
✓
series
TMIN≤TJ≤TMAX
15
25
✓
LT1034B
*
shunt
TMIN≤TJ≤TMAX
40
40
40 (typ)
20
20
40 (typ)
LT1236A
✓
LT1236B
series
5
5
10
10
15
15
10
10
10
15
15
15
20
20
20
25
25
25
TMIN≤TJ≤TMAX
LT1236C
LT1460A, B
LT1460C
✓
series
LT1460D, E
TMIN≤TJ≤TMAX
LT1460F, G
LT1634
✓
LT1634A
LTZ1000
20
5
LT1031D
LT1034
5
20
LT1031B
LT1031C
10V
3
LT1027D
LT1029
5
20
LT1021D
LT1027C
7.0V
✓
shunt
TMIN≤TJ≤TMAX
shunt
TJ = 65˚C
20
10
0.1
**The LT1034 dual reference includes both a bandgap and a buried Zener reference
**Absolute output voltage over temperature guaranteed; tempco is estimated for purposes of comparison
Linear Technology Magazine • August 1997
35
DESIGN INFORMATION
temperatures, thereby causing thermoelectric voltage noise at the output
of the reference. Figure 15 dramatically demonstrates this effect. The
first half of the plot was made with an
LT1021H-7 buried Zener reference,
which was shielded from ambient air
with a small foam cup (Dart Container Corporation Stock No. 8J8 or
similar). The cup was removed at six
minutes elapsed time for the second
half of the test. Ambient in both cases
was a lab bench-top with no excessive
turbulence from air conditioners,
opening/closing doors, foot traffic or
547 exhaust. Removing the foam cup
increased the output noise by almost
an order of magnitude in the 0.01Hz
to 10Hz band.
The kovar leads of the TO-5 working against copper circuit traces are
the primary culprit. Copper lead
frames used on DIP and surface mount
packages are not nearly as sensitive
to air turbulence because they are
intrinsically matched. Still, external
components create thermocouples of
their own with potentials of 10 µV/°C
or more per junction. In a LT1021-7
reference, this represents more than
1ppm/°C shift from each thermoelectric generator. Temperature gradients
across the circuit board and dissipation within external components can
9V-12V
INPUT
+
220Ω
4.7Ω
47µF
RED LED**
ZBD949*
10Ω
1/2W
IN
LT1021-5
OUT
5V/200mA
OUTPUT
2.0Ω
GND
+
10µF
Ta
* ZETEX INC (516) 864-7630
** GLOWS IN CURRENT LIMIT. DO NOT OMIT.
REFACC_17.eps
Figure 17. Ultralow noise 5V, 200mA supply
output noise is 7µVRMS over a 10Hz to 10kHz
bandwidth. Reference noise is guaranteed to
less than 11µVRMS. Standard 3-terminal
regulators have one hundred times the noise
and no guarantees.
36
lead to the same kind of noise as was
shown in Figure 15.
Temperature gradients may arise
from heat generators on the board.
Position the reference and its associated external components far from
heat sources and, if necessary, use
routing techniques to create an isothermal island around the reference
circuitry. Minimize air movement
either by adding a small enclosure
around the reference circuitry, or by
encapsulating the reference circuitry
in self-expanding polyurethane foam.
Reference Applications
The unique pocket reference shown
in Figure 16 is a good match for a pair
of AAA alkaline cells, because the
circuit draws less than 16µA supply
current. Two outputs are provided: a
buffered, 1.5V voltage output, and a
regulated 1µA current source. The
current source compliance ranges
from approximately 1V to –43V.
The reference is self-biased, completely eliminating line regulation as
a concern. Start-up is guaranteed by
the LT1495 op amp, whose output
saturates at 11mV from the negative
rail. Once powered, there is no reason
to turn the circuit off. One AAA alkaline contains 1200mAH capacity,
enough to power the circuit throughout the 5-year shelf life of the battery.
Voltage output accuracy is about
0.17% and current output accuracy
is about 1.2%. Trim R1 to calibrate
the voltage (1kΩ per 0.1%), and R3 to
calibrate the output current (250Ω
per 0.1%).
Low noise synthesizers need quiet
power supplies for their VCOs and
other critical circuitry. 3-terminal
regulators exhibit far too much noise
for this application, calling instead
for a regulator constructed from a
reference. A practical example is
shown in Figure 17. Current through
the LT1021-5 reference is used to
drive the base of a PNP pass device,
resulting in an available output current of at least 1A. In this example,
the current is intentionally limited to
200mA by the addition of emitter
degeneration and base clamping. The
low noise of the reference is preserved,
giving a 100-fold improvement over
the noise of an equivalent 5V, 3-terminal regulator, not to mention
improved initial accuracy and longterm stability. Typical output noise is
7µ VP-P over a 10kHz bandwidth.
Conclusion
When specifying a reference, keep in
mind that initial accuracy, temperature coefficient, and long-term
stability all play a role in overall accuracy of the finished product. By taking
some care in applying the reference,
and by avoiding some key pitfalls, the
reference’s inherent accuracy can be
preserved. Tables 3–5 compare quiescent current, initial accuracy and
temperature coefficient for each of
LTC’s references.
For Further Reading
“The Ultra-Zener—A Portable
Replacement for the Weston Cell?” by
Peter J. Spreadbury; IEEE Transactions on Instrumentation and
Measurement, Vol. 40, No. 2, April
1991, pages 343–346
Application Note 42: Voltage Reference Circuit Collection, by Brian
Huffman; Linear Technology Corporation, June 1991.
Part one of this article appeared in
the June 1997 issue of Linear
Technology.
for
the latest information
on LTC products,
visit
www.linear-tech.com
Linear Technology Magazine • August 1997
NEW DEVICE CAMEOS
New Device Cameos
The LT1497:
Dual 50MHz, 125mA
Current Feedback Amplifier
The LT1497 dual 50MHz current feedback amplifier is ideal for driving
twisted pairs, buffering low impedance loads and driving multiple
back-terminated cables. The device
features high output drive and low
distortion from a modest supply current. From a low 7mA maximum
supply current per amplifier, each
output drives a minimum of ±100mA
to within 2V of each supply. Distortion at up to 1MHz is better than
–70dBc driving ±40mA peak signals
into a 135Ω twisted pair.
Operation is fully specified for
supplies from ±2.5V to ±15V. The
amplifiers have current and thermal
limiting to provide protection against
fault conditions. The LT1497 bridges
the performance between the 30mA
output, 100MHz LT1229 and the
250mA output, 60MHz LT1207 dual
current feedback amplifiers.
The LT1497 is available in a low
thermal resistance SO-16 package
for operation with supplies up to ±15V.
For operation at ±5V and below, the
device is also available in a low thermal resistance SO-8 package.
The LT1634: Micropower,
Precision Voltage Reference
The LT1634 is LTC’s newest micropower, precision, shunt voltage
reference. The LT1634 provides
excellent precision and drift performance at micropower bias currents.
A low operating current of 10µA, guaranteed temperature drift of 25ppm/˚C,
tight initial voltage accuracy of 0.05%
are some of the virtues of the LT1634.
The LT1634 comes in four popular
voltages: 1.25V, 2.50V, 4.096V and
5.0V.
The bandgap reference uses
trimmed precision thin-film resistors
to achieve 0.05% initial voltage accuracy. Advances in design, processing
and packaging guarantee 10µA operation and low temperature-cycling
Linear Technology Magazine • August 1997
hysteresis. Improved curvature correction techniques guarantee 25ppm
maximum temperature drift. Board
space is minimized with surface
mount SO-8 and MSOP and throughhole TO-92 (Z) packages. To further
reduce board space, the LT1634 requires no output compensation
capacitor: it is stable with any capacitive load over the full operating current
range of 10µA to 20mA.
The LT1634 is a high performance
upgrade to the LM185/LM385,
LT1004 and LT1034. The performance
of the LT1634 makes it the ideal choice
for applications where high precision
and minimum power consumption
are important. LT1634 is available in
the commercial grade.
The LTC1659: Ultrasmall,
8-Lead MSOP Packaged, Low
Power, 12-Bit Multiplying
Voltage-Output DAC
The latest addition to LTC’s family of
12-bit voltage-output DACs is the
multiplying LTC1659. Packaged in
an 8-lead MSOP, the LTC1659 operates on a single supply of 2.7V to
5.5V. The LTC1659 requires an external reference voltage source. The
gain between the reference pin and
the output is VIN(CODE/4096). For
applications that require rail-to-rail
output, connect VCC to the reference
pin for an output swing from GND to
VCC. The LTC1659 features a DOUT
pin that allows data daisy-chaining,
and a simple 3-line (CLK, DIN, CS/LD)
serial interface, allowing easy connection to microcontrollers and
microprocessors.
The LTC1448: Dual Low
Power, 12-Bit Multiplying,
Voltage-Output DAC
The latest addition to LTC’s family of
dual 12-bit voltage-output DACs is
the multiplying LTC1448. Packaged
in an SO-8, the LTC1448 operates on
a single supply of 2.7V to 5.5V. The
LTC1448 requires an external refer-
ence voltage source. The gain between the reference pin and the output
is VIN(CODE/4096). For applications
that require rail-to-rail output,
connect VCC to the reference pin for
an output swing from GND to VCC.
The LTC1448 features a simple 3-line
(CLK, DIN, CS/LD) serial interface,
allowing easy connection to microcontrollers and microprocessors.
The LTC1412: Low Power,
3Msps 12-Bit ADC
Adding to LTC’s family of high speed,
low power analog-to-digital converters, the LTC1412 samples analog
input signals at up to 3Msps with 12bit resolution and accuracy. The
LTC1412 operates on a ±5V supply
and dissipates just 150mW at full
conversion speed. The converter has
an analog input range of ±2.5V. It is
designed for high speed, high
resolution signal processing applications, including telecom digital-data
transmission applications, wide
bandwidth multichannel data acquisition and baseband signal recovery
through undersampling. Its simple
parallel interface and conversion start
signal input make it easy to use in
DSP-based designs. The LTC1412
includes an internal reference and
conversion clock, microprocessor or
microcontroller compatible 12-bit
parallel interface and a fully differential input that achieves better than
70dB CMRR over a 0Hz to 3MHz bandwidth. Data is available immediately,
without pipeline delay, at the conclusion of a conversion. The LTC1412 is
available in a space-efficient 28-pin
SO package.
The LTC1412’s unique S/H has
two very beneficial features that apply when sampling either single-ended
or differential signals. The first is a
wide, 40MHz full-power input bandwidth. This wide input bandwidth
allows the LTC1412 to undersample
signals far above the converter’s
Nyquist frequency and preserve their
fidelity. The second is a common mode
37
NEW DEVICE CAMEOS
rejection of 60dB. When sampling
differentially, the common mode
rejection is especially useful for
suppressing the perturbing effects of
common mode noise and ground
loops.
The LTC1412 combines excellent
dynamic performance with a high
speed conversion rate. The signal-tonoise + distortion (SINAD) is 72dB
and the total harmonic distortion
(THD) is –84dB when sampling a
1.5MHz full-scale input signal at
3Msps.
The LTC1414: Low Power,
2.2Msps 14-Bit ADC
Following on the success of the
LTC1419, the world’s cleanest 14-bit
ADC, LTC has just released the
LTC1414. This new high speed, low
power analog-to-digital converter
samples analog input signals at up to
2.2Msps with 14-bit resolution and
accuracy.
The LTC1414 operates on a ±5V
supply and dissipates just 150mW at
full conversion speed. The converter
has an analog input range of ±2.5V. It
is designed for high speed, high
resolution applications, including
telecom digital-data transmission,
DSP-based signal processing,
wide bandwidth multichannel data
acquisition and baseband signal
recovery through undersampling. The
L TC1414 includes an internal
reference, a fast 14-bit parallel interface, and a fully differential input
S/H. Conversion results are available
without a pipeline delay. The LTC1414
is available in a space-efficient 28pin narrow SSOP package.
The LTC1414’s S/H has a wide,
20MHz full power input bandwidth.
This allows the LTC1414 to
undersample signals far above the
converter’s Nyquist frequency and
preserve their fidelity. Its input common mode rejection is better than
70dB over a 0Hz to 3MHz bandwidth.
This is especially useful for suppressing the deleterious effects of
common mode noise and ground loops
when sampling differentially. These
features of the LTC1414’s unique S/H
apply when sampling either singleended and differential signals.
The LTC1414’s high speed conversion rate does not sacrifice dynamic
performance. The signal-to-noise +
distortion (SINAD) is 80.5dB and the
spurious-free dynamic range is 95dB
with a 100kHz input signal. This spurious-free dynamic range is an
increase of 10dB over 12-bit devices.
The SINAD is 78dB at fS = 2.2Msps
and fIN = 1.1MHz.
Authors can be contacted
at (408) 432-1900
for
the latest information
on LTC products,
visit
www.linear-tech.com
For further information on any
of the devices mentioned in this
issue of Linear Technology, use
the reader service card or call
the LTC literature service
number:
1-800-4-LINEAR
Ask for the pertinent data sheets
and Application Notes.
38
Linear Technology Magazine • August 1997
DESIGN TOOLS
DESIGN TOOLS
Applications on Disk
Noise Disk — This IBM-PC (or compatible) program
allows the user to calculate circuit noise using LTC op
amps, determine the best LTC op amp for a low noise
application, display the noise data for LTC op amps,
calculate resistor noise and calculate noise using specs
for any op amp.
Available at no charge
SPICE Macromodel Disk — This IBM-PC (or compatible) high density diskette contains the library of LTC
op amp SPICE macromodels. The models can be used
with any version of SPICE for general analog circuit
simulations. The diskette also contains working circuit
examples using the models and a demonstration copy
of PSPICE™ by MicroSim.
Available at no charge
SwitcherCAD™ — The SwitcherCAD program is a powerful PC software tool that aids in the design and
optimization of switching regulators. The program can
cut days off the design cycle by selecting topologies,
calculating operating points and specifying component values and manufacturer’s part numbers. 144
page manual included.
$20.00
SwitcherCAD supports the following parts: LT1070
series: LT1070, LT1071, LT1072, LT1074 and LT1076.
LT1082. LT1170 series: LT1170, LT1171, LT1172 and
LT1176. It also supports: LT1268, LT1269 and LT1507.
LT1270 series: LT1270 and LT1271. LT1371 series:
LT1371, LT1372, LT1373, LT1375, LT1376 and
LT1377.
Micropower SwitcherCAD™ — The MicropowerSCAD
program is a powerful tool for designing DC/DC converters based on Linear Technology’s micropower
switching regulator ICs. Given basic design parameters, MicropowerSCAD selects a circuit topology and
offers you a selection of appropriate Linear Technology
switching regulator ICs. MicropowerSCAD also performs circuit simulations to select the other components
which surround the DC/DC converter. In the case of a
battery supply, MicropowerSCAD can perform a battery life simulation. 44 page manual included.
$20.00
MicropowerSCAD supports the following LTC micropower DC/DC converters: LT1073, LT1107, LT1108,
LT1109, LT1109A, LT1110, LT1111, LT1173, LTC1174,
LT1300, LT1301 and LT1303.
Technical Books
1990 Linear Databook, Vol I —This 1440 page collection of data sheets covers op amps, voltage regulators,
references, comparators, filters, PWMs, data conversion and interface products (bipolar and CMOS), in
both commercial and military grades. The catalog
features well over 300 devices.
$10.00
1992 Linear Databook, Vol II — This 1248 page
supplement to the 1990 Linear Databook is a collection
of all products introduced in 1991 and 1992. The
catalog contains full data sheets for over 140 devices.
The 1992 Linear Databook, Vol II is a companion to the
1990 Linear Databook, which should not be discarded.
$10.00
Linear Technology Magazine • August 1997
1994 Linear Databook, Vol III —This 1826 page
supplement to the 1990 and 1992 Linear Databooks is
a collection of all products introduced since 1992. A
total of 152 product data sheets are included with
updated selection guides. The 1994 Linear Databook
Vol III is a companion to the 1990 and 1992 Linear
Databooks, which should not be discarded. $10.00
1995 Linear Databook, Vol IV —This 1152 page
supplement to the 1990, 1992 and 1994 Linear Databooks is a collection of all products introduced since
1994. A total of 80 product data sheets are included
with updated selection guides. The 1995 Linear Databook Vol IV is a companion to the 1990, 1992 and 1994
Linear Databooks, which should not be discarded.
$10.00
1996 Linear Databook, Vol V —This 1152 page supplement to the 1990, 1992, 1994 and 1995 Linear
Databooks is a collection of all products introduced
since 1995. A total of 65 product data sheets are
included with updated selection guides. The 1996
Linear Databook Vol V is a companion to the 1990,
1992, 1994 and 1995 Linear Databooks, which should
not be discarded.
$10.00
1990 Linear Applications Handbook, Volume I —
928 pages full of application ideas covered in depth by
40 Application Notes and 33 Design Notes. This catalog covers a broad range of “real world” linear circuitry.
In addition to detailed, systems-oriented circuits, this
handbook contains broad tutorial content together
with liberal use of schematics and scope photography.
A special feature in this edition includes a 22-page
section on SPICE macromodels.
$20.00
1993 Linear Applications Handbook, Volume II —
Continues the stream of “real world” linear circuitry
initiated by the 1990 Handbook. Similar in scope to the
1990 edition, the new book covers Application Notes
40 through 54 and Design Notes 33 through 69.
References and articles from non-LTC publications
that we have found useful are also included. $20.00
1997 Linear Applications Handbook, Volume III —
This 976 page handbook maintains the practical outlook
and tutorial nature of previous efforts, while broadening topic selection. This new book includes Application
Notes 55 through 69 and Design Notes 70 through
144. Subjects include switching regulators, measurement and control circuits, filters, video designs,
interface, data converters, power products, battery
chargers and CCFL inverters. An extensive subject
index references circuits in LTC data sheets, design
notes, application notes and Linear Technology magazines.
$20.00
Interface Product Handbook — This 424 page handbook features LTC’s complete line of line driver and
receiver products for RS232, RS485, RS423, RS422,
V.35 and AppleTalk ® applications. Linear’s particular
expertise in this area involves low power consumption,
high numbers of drivers and receivers in one package,
mixed RS232 and RS485 devices, 10kV ESD protection of RS232 devices and surface mount packages.
Available at no charge
Power Solutions Brochure — This 84 page collection
of circuits contains real-life solutions for common
power supply design problems. There are over 88
circuits, including descriptions, graphs and performance specifications. Topics covered include battery
chargers, PCMCIA power management, microprocessor power supplies, portable equipment power supplies,
micropower DC/DC, step-up and step-down switching
regulators, off-line switching regulators, linear regulators and switched capacitor conversion.
Available at no charge
High Speed Amplifier Solutions Brochure —
This 72 page collection of circuits contains real-life
solutions for problems that require high speed
amplifiers. There are 82 circuits including descriptions, graphs and performance specifications. Topics
covered include basic amplifiers, video-related applications circuits, instrumentation, DAC and photodiode
amplifiers, filters, variable gain, oscillators and current
sources and other unusual application circuits.
Available at no charge
Data Conversion Solutions Brochure — This 52 page
collection of data conversion circuits, products and
selection guides serves as excellent reference for the
data acquisition system designer. Over 60 products
are showcased, solving problems in low power, small
size and high performance data conversion applications—with performance graphs and specifications.
Topics covered include ADCs, DACs, voltage references and analog multiplexers. A complete glossary
defines data conversion specifications; a list of selected application and design notes is also included.
Available at no charge
Telecommunications Solutions Brochure — This 72
page collection of circuits, new products and selection
guides covers a wide variety of products targeted for
the telecommunications industry. Circuits solving real
life problems are shown for central office switching,
cellular phone, base station and other telecom applications. New products introduced include high speed
amplifiers, A/D converters, power products, interface
transceivers and filters. Reference material includes a
telecommunications glossary, serial interface standards, protocol information and a complete list of key
application notes and design notes.
Available at no charge
continued on page 40
Acrobat is a trademark of Adobe Systems, Inc. AppleTalk
is a registered trademark of Apple Computer, Inc. PSPICE
is a trademark of MicroSim Corp.
Information furnished by Linear Technology Corporation
is believed to be accurate and reliable. However, Linear
Technology makes no representation that the circuits
described herein will not infringe on existing patent rights.
39
DESIGN TOOLS, continued from page 39
CD-ROM
LinearView — LinearView™ CD-ROM version 2.0 is
Linear Technology’s latest interactive CD-ROM. It allows you to instantly access thousands of pages of
product and applications information, covering Linear
Technology’s complete line of high performance analog products, with easy-to-use search tools.
The LinearView CD-ROM includes the complete product specifications from Linear Technology’s Databook
library (Volumes I–V) and the complete Applications
Handbook collection (Volumes I–III). Our extensive
collection of Design Notes and the complete collection
of Linear Technology magazine are also included.
A powerful search engine built into the LinearView CDROM enables you to select parts by various criteria,
such as device parameters, keywords or part numbers.
All product categories are represented: data conversion, references, amplifiers, power products, filters
and interface circuits. Up-to-date versions of Linear
Technology’s software design tools, SwitcherCAD,
Micropower SwitcherCAD, FilterCAD, Noise Disk and
Spice Macromodel library, are also included. Everything you need to know about Linear Technology’s
products and applications is readily accessible via
LinearView. LinearView 2.0 runs under Windows ® 3.1,
Windows 95 and Macintosh ® System 7.0 or later.
Available at no charge.
World Wide Web Site
Linear Technology Corporation’s customers can now
quickly and conveniently find and retrieve the latest
technical information covering the Company’s products on LTC’s new internet web site. Located at
www.linear-tech.com, this site allows anyone with
internet access and a web browser to search through
all of LTC’s technical publications, including data sheets,
application notes, design notes, Linear Technology
magazine issues and other LTC publications, to find
information on LTC parts and applications circuits.
Other areas within the site include help, news and
information about Linear Technology and its sales
offices.
Other web sites usually require the visitor to download
large document files to see if they contain the desired
information. This is cumbersome and inconvenient. To
save you time and ensure that you receive the correct
information the first time, the first page of each data
sheet, application note and Linear Technology magazine is recreated in a fast, download-friendly format.
This allows you to determine whether the document is
what you need, before downloading the entire file.
The site is searchable by criteria such as part numbers,
functions, topics and applications. The search is performed on a user-defined combination of data sheets,
application notes, design notes and Linear Technology
magazine articles. Any data sheet, application note,
design note or magazine article can be downloaded or
faxed back. (Files are downloaded in Adobe Acrobat™
PDF format; you will need a copy of Acrobat Reader to
view or print them. The site includes a link from which
you can download this program.)
World Headquarters
Linear Technology Corporation
1630 McCarthy Boulevard
Milpitas, CA 95035-7417
Phone: (408) 432-1900
FAX: (408) 434-0507
U.S. Area
Sales Offices
NORTHEAST REGION
Linear Technology Corporation
3220 Tillman Drive, Suite 120
Bensalem, PA 19020
Phone: (215) 638-9667
FAX: (215) 638-9764
Linear Technology Corporation
266 Lowell St., Suite B-8
Wilmington, MA 01887
Phone: (508) 658-3881
FAX: (508) 658-2701
NORTHWEST REGION
Linear Technology Corporation
1900 McCarthy Blvd., Suite 205
Milpitas, CA 95035
Phone: (408) 428-2050
FAX: (408) 432-6331
SOUTHEAST REGION
Linear Technology Corporation
17000 Dallas Parkway
Suite 219
Dallas, TX 75248
Phone: (214) 733-3071
FAX: (214) 380-5138
Linear Technology Corporation
5510 Six Forks Road
Suite 102
Raleigh, NC 27609
Phone: (919) 870-5106
FAX: (919) 870-8831
CENTRAL REGION
Linear Technology Corporation
Chesapeake Square
229 Mitchell Court, Suite A-25
Addison, IL 60101
Phone: (708) 620-6910
FAX: (708) 620-6977
SOUTHWEST REGION
Linear Technology Corporation
21243 Ventura Blvd.
Suite 227
Woodland Hills, CA 91364
Phone: (818) 703-0835
FAX: (818) 703-0517
Linear Technology Corporation
15375 Barranca Parkway
Suite A-211
Irvine, CA 92718
Phone: (714) 453-4650
FAX: (714) 453-4765
International
Sales Offices
FRANCE
Linear Technology S.A.R.L.
Immeuble “Le Quartz”
58 Chemin de la Justice
92290 Chatenay Malabry
France
Phone: 33-1-41079555
FAX: 33-1-46314613
GERMANY
Linear Technology GmbH
Oskar-Messter-Str. 24
85737 Ismaning
Germany
Phone: 49-89-962455-0
FAX: 49-89-963147
JAPAN
Linear Technology KK
5F NAO Bldg.
1-14 Shin-Ogawa-cho Shinjuku-ku
Tokyo, 162
Japan
Phone: 81-3-3267-7891
FAX: 81-3-3267-8510
KOREA
Linear Technology Korea Co., Ltd
Namsong Building, #403
Itaewon-Dong 260-199
Yongsan-Ku, Seoul 140-200
Korea
Phone: 82-2-792-1617
FAX: 82-2-792-1619
SINGAPORE
Linear Technology Pte. Ltd.
507 Yishun Industrial Park A
Singapore 2776
Phone: 65-753-2692
FAX: 65-754-4113
SWEDEN
Linear Technology AB
Sollentunavägen 63
S-191 40 Sollentuna
Sweden
Phone: 46-8-623-1600
FAX: 46-8-623-1650
TAIWAN
Linear Technology Corporation
Rm. 602, No. 46, Sec. 2
Chung Shan N. Rd.
Taipei, Taiwan, R.O.C.
Phone: 886-2-521-7575
FAX: 886-2-562-2285
UNITED KINGDOM
Linear Technology (UK) Ltd.
The Coliseum, Riverside Way
Camberley, Surrey GU15 3YL
United Kingdom
Phone: 44-1276-677676
FAX: 44-1276-64851
LINEAR TECHNOLOGY CORPORATION
1630 McCarthy Boulevard
Milpitas, CA 95035-7417
(408) 432-1900 FAX (408) 434-0507
www.linear-tech.com
For Literature Only: 1-800-4-LINEAR
Acrobat is a trademark of Adobe Systems, Inc.; Windows is
a registered trademark of Microsoft Corp.; Macintosh is a
registered trademark of Apple Computer, Inc.
© 1997 Linear Technology Corporation/Printed in U.S.A./40K
Linear Technology Magazine • August 1997