AN43 Digital indicator for bondedjauge strain gauges Transducers excitation 10 000 counts LED display Zero and span adjustment on front panel Analog output 4-20 mA or 0-10 V 2 alarm tresholds (option) Average, minimum, maximum value Digital tare (re-zero) Conforms to CE (European directive 89/336/CEE) The AN43 digital indicator provides the necessary low-voltage excitation required for bonded metal strain gauges, thus making these indicators easy to use with most pressure and force transducers. Independent zero and span adjustment is available from the front panel. Caractéristiques (20 °C) Display -1999 to +9999 counts, red LED. Overrange : display dEP Decimal point programmed on front panel. Power supply 230 V / 50 Hz. Consumption : 6 W Excitation voltage output 5 V, 10 V, by jumper Complet bridge 100 to 5000 Ω Input 0-30 mV Operating temperature 0 ... 60°C Storage temperature -40 ... 85°C Tightness IP20 according to NF EN 60529 Accuracy ± 0,1% F.S. ± 1 digit. Reading rate 7 reading/second Alarms 2 independent thresholds programmable in hysteresis Resolution ± 3 counts Fully adjustable switches on the display range Relays on when signal above set point (can be reversed). Load rating: 3A-24 Vdc ; 0,5 A-220 Vac Direct current: 150 W to 24 Vdc, 50 W to 220 Vdc Alternating current : 250 Vac. Analog output (non isolated) 0-10 V (standard) or 4-20 mA (option), lowscale and high-scale values are adjustable on the full range. Max current output limited to 50 mA/750 Ω Max current (voltage output) limited to 10mA/75 Ω. www.baumer.com/process Modifications reserved. Options 110 V/50 Hz, 48 V/50 Hz, 24 V/50 Hz, 24 Vdc power supply Front panel IP 55 Front Keypads Analog output 4-20 mA Calibration with certificate Q1060 Data sheet D21.03 Page 1 Wiring AN 43 supply 1 23 230V [NE] 230V [PH] alarms 1 23 45 8 7 6 5 4 3 2 1 T R A N S D U C E R RAZ tare + power supply + signal (transducer) + analog output - Bld Al1 Al2 PRESSURE leaflet n° E101-E111 E801-EY81 EMD1-EG51 EFO 304036 FORCE leaflet n° FXF1-FXC1 FXD1 FXG1-FXK1 304051 304053 304010 304042 Dimensions (mm) UK/08-2007 This data sheet must only be copied in full. Panel cut out 500 g Ordering Details - AN43 AN4xxxxxx Family Accessories electronic Type Digital indicator for bondedjauge strain gauges 1´ digit A 2 ... 4´ digit N 43 Power supply 220 Vac (standard) 110 Vac 24 Vac 24 Vdc 48 Vac 5´ digit Output signal (copy) 0-10 Vcc (standard) 4-20 mA 7´ digit Tresholds 2 Tresholds 8´ digit Transmitter with indicator calibrated together Without Phisical unit display (to specifybar, psi, daN) End points calibration (zero and span) Q1060 calibration certificate 21 points Q1060 calibration certificate 11 points 9´ digit www.baumer.com/process Modifications reserved. A D E F J 02 03 2 0 1 2 3 5 Data sheet D21.03 Page 2