Package Information www.vishay.com Vishay Siliconix MLP 4.5 x 3.5-22L BWL Case Outline 2x D A 5 6 Pin 1 dot by marking A 0.08 C K1 0.1 C A D1-2 D1-1 A1 22 21 20 19 A2 18 17 D2-1 K4 D2-4 17 18 19 20 21 22 2x 12 E2-2 2 3 e K2 4 5 B 6 7 8 9 11 10 9 10 11 C DIM. 8 D2-3 MILLIMETERS E1-2 13 12 K3 E2-3 E1-1 13 5 b 4 E1-5 15 14 E1-3 E2-4 14 E2-1 15 3 E 2 1 16 16 E1-4 0.1 C B 1 7 D2-2 6 L INCHES MIN. NOM. MAX. MIN. NOM. A (8) 0.70 0.75 0.80 0.027 0.0029 0.031 A1 0.00 - 0.05 0.000 - 0.002 0.30 0.0078 A2 b (4) 0.20 ref. 0.20 0.25 0.008 ref. 0.0098 D 4.50 BSC 0.177 BSC e 0.50 BSC 0.019 BSC E L 3.50 BSC 0.35 0.40 MAX. 0.0110 0.137 BSC 0.45 0.013 0.015 N (3) 22 22 Nd (3) 6 6 Ne (3) 5 5 0.017 D1-1 0.35 0.40 0.45 0.013 0.015 0.017 D1-2 0.15 0.20 0.25 0.005 0.007 0.009 D2-1 1.02 1.07 1.12 0.040 0.042 0.044 D2-2 1.02 1.07 1.12 0.040 0.042 0.044 D2-3 1.47 1.52 1.57 0.057 0.059 0.061 D2-4 0.25 0.30 0.35 0.009 0.011 0.013 E1-1 1.095 1.145 1.195 0.043 0.045 0.047 E1-2 2.67 2.72 2.77 0.105 0.107 0.109 E1-3 0.35 0.40 0.45 0.013 0.015 0.017 E1-4 1.85 1.90 1.95 0.072 0.074 0.076 E1-5 0.095 0.145 0.195 0.0037 0.0057 0.0076 E2-1 3.05 3.10 3.15 0.120 0.122 0.124 E2-2 1.065 1.115 1.165 0.0419 0.0438 0.0458 E2-3 0.695 0.745 0.795 0.027 0.029 0.031 E2-4 0.40 0.45 0.50 0.015 0.017 0.019 K1 0.40 BSC 0.015 BSC K2 0.07 BSC 0.002 BSC K3 0.05 BSC 0.001 BSC K4 0.40 BSC 0.015 BSC Document Number: 67234 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 20-Oct-14 Package Information www.vishay.com Vishay Siliconix Notes 1. Use millimeters as the primary measurement 2. Dimensioning and tolerances conform to ASME Y14.5M. - 1994 3. N is the number of terminals, Nd is the number of terminals in X-direction and Ne is the number of terminals in Y-direction. 4. Dimension b applies to plated terminal and is measured between 0.20 mm and 0.25 mm from terminal tip 5. The pin #1 identifier must be existed on the top surface of the package by using indentation mark or other feature of package body 6. Exact shape and size of this feature is optional 7. Package warpage max. 0.08 mm 8. Applied only for terminals T14-0626-Rev. A, 20-Oct-14 DWG: 6028 Document Number: 67234 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 20-Oct-14