V I S H AY I N T E R T E C H N O L O G Y, I N C . THIN FILM RESISTORS TNPS....ESCC Resistors - Avionics, Military, and Space Hi-Rel Thin Film Chip Resistors KEY BENEFITS • • • • High-reliability product ESA approved to ESCC 4001/029 Advanced thin film technology SnPb termination plating, minimum 6 % Pb APPLICATIONS • Aerospace • Avionics • Military RESOURCES • Datasheet: TNPS....ESCC: http://www.vishay.com/doc?28789 • For technical questions contact [email protected] One of the World’s Largest Manufacturers of Discrete Semiconductors and Passive Components PRODUCT SHEET 1/4 VMN-PT0381-1308 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 V I S H AY I N T E R T E C H N O L O G Y, I N C . THIN FILM RESISTORS TNPS....ESCC TNPS .... ESCC www.vishay.com Vishay Draloric Hi-Rel Thin Film ChipResistors Resistors Hi-Rel Thin Film Chip • High-reliability product • ESA approved to ESCC 4001/029 • Advanced thin film technology • SnPb termination plating, minimum 6 % Pb APPLICATIONS • Aerospace TNPS .... ESCC high-reliability thin film chip resistors are the premium choice for design and manufacture of equipment where a mature technology and proven reliability are of utmost importance. They are regularly used in communication and research satellites and fit equally well into aircraft and military electronic systems. • Avionics • Military METRIC SIZE IMPERIAL Approval of the TNPS .... ESCC products is granted by the European Space Components Coordination and registered in the ESCC Qualified Parts List, REP005. METRIC 0603 0805 1206 RR1608M RR2012M RR3216M TECHNICAL SPECIFICATIONS DESCRIPTION Metric size Resistance range TNPS0603 .... ESCC TNPS0805 .... ESCC RR1608M RR2012M RR3216M 10.0 Ω to 221 kΩ 10.0 Ω to 422 kΩ 10.0 Ω to 1.00 MΩ Resistance tolerance TNPS1206 .... ESCC ± 1 %; ± 0.5 %; ± 0.1 % Temperature coefficient ± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K Rated dissipation P70 0.1 W 0.125 W 0.25 W Operating voltage, Umax. ACRMS or DC 75 V 150 V 200 V Permissible film temperature, ϑF max. 125 °C Operating temperature range - 55 °C to 125 °C Max. resistance change at P70, |ΔR| max., after: ≤ (0.05 % R + 10 mΩ) 1000 h ≤ (0.1 % R + 20 mΩ) 2000 h Permissible voltage against ambient (insulation) 100 V Storage temperature range 200 V 300 V -55 °C to +125 °C Note • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. TEMPERATURE COEFFICIENT AND RESISTANCE RANGE DESCRIPTION Revision 09-Sep-13 Resistors - Avionics, Military, and Space FEATURES TCR ± 50 ppm/K ± 25 ppm/K ± 15 ppm/K RESISTANCE RANGE TOLERANCE TNPS0603 .... ESCC TNPS0805 .... ESCC ±1% 10.0 Ω to 221 kΩ 10.0 Ω to 422 kΩ TNPS1206 .... ESCC 10.0 Ω to 1.00 MΩ ± 0.5 % 10.0 Ω to 221 kΩ 10.0 Ω to 422 kΩ 10.0 Ω to 1.00 MΩ ± 0.1 % 10.0 Ω to 221 kΩ 10.0 Ω to 422 kΩ 10.0 Ω to 1.00 MΩ ± 0.1 % 10.0 Ω to 221 kΩ 10.0 Ω to 422 kΩ 10.0 Ω to 1.00 MΩ Notes • The indicated combinations of TCR, tolerance and resistance range are a subset of those combinations approved to ESCC 4001/029 • According to ESCC 4001/029, resistance values are to be selected from the E96 series only Revision: 09-Sep-13 PRODUCT Document Number: 28789 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT SHEET 2/4 SET FORTH AT www.vishay.com/doc?91000 VMN-PT0381-1308 ARE SUBJECT TO SPECIFIC DISCLAIMERS, THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 V I S H AY I N T E R T E C H N O L O G Y, I N C . THIN FILM RESISTORS TNPS....ESCC Hi-Rel Thin Film Chip Resistors TNPS .... ESCC www.vishay.com Vishay Draloric Power Dissipation P Resistors - Avionics, Military, and Space FUNCTIONAL PERFORMANCE TNPS1206 TNPS0805 TNPS0603 0.3 W 0.2 0.1 0 - 50 0 50 70 Current Noise A1 Derating 1 100 125 °C 150 Ambient Temperature ϑamb TNPS1206 TNPS0805 TNPS0603 µV/V 0.1 0.01 100 1K 10K Ω 100K 1M Resistance Value R Non-Linearity A 3 Current Noise A1 in accordance with IEC 60195 120 dB 100 80 60 40 10 TNPS1206 TNPS0805 TNPS0603 100 1K 10K 100K Ω 1M Resistance Value R Non-Linearity A3 in accordance with IEC/TR 60440 Revision: 09-Sep-13 Document Number: 28789 5 3/4 [email protected] VMN-PT0381-1308 For technical questions, contact: THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRODUCT SHEET THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 V I S H AY I N T E R T E C H N O L O G Y, I N C . THIN FILM RESISTORS TNPS....ESCC TNPS .... ESCC www.vishay.com Vishay Draloric DESCRIPTION SCREENING TESTS Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade ceramic substrate (Al2O3) and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are deposited on both sides. A special laser is used to achieve the target value by smoothly fine trimming resistive layer without damaging the ceramics. A further conditioning is applied in order to stabilize the trimming result. The resistor elements are covered by a protective coating designed for electrical, mechanical, and climatic protection. The terminations receive a final SnPb plating, controlled for a minimum lead content of 6 %. The resistance value is stamped on the coating with a four-character code system according to IEC 60062 (1). The result of the determined production is verified by an extensive testing procedure performed on 100 % of the individual chip resistors. Only accepted products are placed into a special matrix case packaging or into antistatic blister tape in accordance with IEC 60286-3 (1). These products are subjected to a screening test according to the ruling of the generic specification ESCC 4001 and the detail specification ESCC 4001/029. ASSEMBLY Deliverable item to the Lot Validation Tests is the test report together with the used samples, shipped in waffle tray package. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow, or vapor phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters, and aqueous solutions. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. Solderability is specified for 2 years after production. The permitted storage time is 20 years. The production is succeeded by production test sequences for resistance, plating properties, solderability, and dimensions. This sequence is followed by screening tests for overload, non-linearity, temperature coefficient, resistance at room temperature, and a visual inspection. A Certificate of Conformity provides summary information by reporting the numbers of rejects for each test or inspection. LOT VALIDATION TESTS Execution of Lot Validation Tests according to the ruling of ESCC 4001 is available as a separate order item. This is to be combined with the dedicated order line for the required amount of samples, using packaging code “LX”. The applicable scope of the Lot Validation Tests, graduated to Group 1, Group 2, and Group 3, is illustrated in the datasheet with the number of samples required for each level. APPROVALS The resistors are approved to ESCC 4001/029. Conformity is indicated by the ESCC Qualified Components logo on the package label. Approval is granted by the European Space Components Coordination and registered in the ESCC Qualified Parts List, REP005. Revision 09-Sep-13 Resistors - Avionics, Military, and Space Hi-Rel Thin Film Chip Resistors The detail specification ESCC 4001/029 has been established after successful completion of an Evaluation Test Programme according to ESCC 2264000. Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents Revision: 09-Sep-13 Document Number: 28789 4 4/4 [email protected] VMN-PT0381-1308 For technical questions, contact: THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PRODUCT SHEET