ISL6306 ® Data Sheet May 5, 2008 4-Phase PWM Controller with 8-Bit DAC Code Capable of Precision rDS(ON) or DCR Differential Current Sensing The ISL6306 controls microprocessor core voltage regulation by driving up to 4 synchronous-rectified buck channels in parallel. Multiphase buck converter architecture uses interleaved timing to multiply channel ripple frequency and reduce input and output ripple currents. Lower ripple results in fewer components, lower component cost, reduced power dissipation, and smaller implementation area. Microprocessor loads can generate load transients with extremely fast edge rates. The ISL6306 features a high bandwidth control loop and ripple frequencies up to >4MHz to provide optimal response to the transients. Today’s microprocessors require a tightly regulated output voltage position versus load current (droop). The ISL6306 senses current by utilizing patented techniques to measure the voltage across the on resistance, rDS(ON), of the lower MOSFETs or DCR of the output inductor during the lower MOSFET conduction intervals. Current sensing provides the needed signals for precision droop, channel-current balancing, and overcurrent protection. A programmable internal temperature compensation function is implemented to effectively compensate for the temperature coefficient of the current sense element. A unity gain, differential amplifier is provided for remote voltage sensing. Any potential difference between remote and local grounds can be completely eliminated using the remotesense amplifier. Eliminating ground differences improves regulation and protection accuracy. The threshold-sensitive enable input is available to accurately coordinate the start up of the ISL6306 with any other voltage rail. Dynamic-VID™ technology allows seamless on-the-fly VID changes. The offset pin allows accurate voltage offset settings that are independent of VID setting. FN9226.1 Features • Precision Multiphase Core Voltage Regulation - Differential Remote Voltage Sensing - ±0.5% System Accuracy Over Life, Load, Line and Temperature - Adjustable Precision Reference-Voltage Offset • Precision rDS(ON) or DCR Current Sensing - Accurate Load-Line Programming - Accurate Channel-Current Balancing - Differential Current Sense • Microprocessor Voltage Identification Input - Dynamic VID™ Technology - 8-Bit VID Input with Selectable VR11 Code and Extended VR10 Code at 6.25mV per Bit - 0.5V to 1.6V Operation Range • Thermal Monitoring • Integrated Programmable Temperature Compensation • Threshold-Sensitive Enable Function for Power Sequencing and VTT Enable • Overcurrent Protection • Overvoltage Protection • 2-, 3- or 4-Phase Operation • Adjustable Switching Frequency Up to 1MHz Per Phase • Package Option - QFN Compliant to JEDEC PUB95 MO-220 QFN - Quad Flat No Leads - Product Outline - QFN Near Chip Scale Package Footprint; Improves PCB Efficiency, Thinner in Profile • Pb-Free (RoHS Compliant) Ordering Information PART NUMBER (Note) ISL6306CRZ* PART MARKING TEMP. (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL6306 CRZ 0 to +70 40 Ld 6x6 QFN L40.6x6 ISL6306CRZ-TK ISL6306 CRZ 0 to +70 40 Ld 6x6 QFN L40.6x6 ISL6306IRZ* ISL6306 IRZ -40 to +85 40 Ld 6x6 QFN L40.6x6 *Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved. Dynamic VID™ is a trademark of Intersil Americas Inc. All other trademarks mentioned are the property of their respective owners. ISL6306 Pinout VID7 TM VR_HOT VR_FAN VR_RDY SS FS EN_VTT EN_PWR PWM3 ISL6306 (40 LD QFN) TOP VIEW 40 39 38 37 36 35 34 33 32 31 VID6 1 30 ISEN3+ VID5 2 29 ISEN3- VID4 3 28 ISEN2- VID3 4 27 ISEN2+ VID2 5 26 PWM2 GND 2 23 ISEN4- OFS 9 22 ISEN1- DAC 10 21 ISEN1+ 11 12 13 14 15 16 17 18 19 20 PWM1 8 VCC VRSEL TCOMP ISEN4+ VSEN 24 RGND 7 VDIFF VID0 IDROOP PWM4 FB 25 COMP 6 REF VID1 FN9226.1 May 5, 2008 ISL6306 ISL6306CR Block Diagram VDIFF VR_RDY VCC 0.875V RGND POWER-ON x1 EN_VTT RESET (POR) VSEN 0.875V EN_PWR OVP THREE-STATE SOFT-START AND FAULT LOGIC +175mV CLOCK AND SAWTOOTH GENERATOR ∑ SS OFS FS PWM1 PWM OFFSET ∑ PWM2 PWM REF DAC VRSEL ∑ PWM3 PWM VID7 VID6 VID5 VID4 DYNAMIC VID VID3 D/A ∑ PWM4 PWM VID2 E/A VID1 CHANNEL CURRENT BALANCE VID0 CHANNEL DETECT COMP ISEN1+ I_TRIP FB ISEN1- OC IDROOP 1 N ∑ I_AVG VR_HOT MONITORING CHANNEL ISEN2- CURRENT SENSE ISEN3+ ISEN3- THERMAL COMPENSATION GAIN THERMAL ISEN2+ TEMPERATURE COMPENSATION ISEN4+ VR_FAN ISEN4- TM TCOMP 3 GND FN9226.1 May 5, 2008 ISL6306 Typical Application - 4-Phase Buck Converter with rDS(ON) Sensing and External TCOMP +12V VIN VCC BOOT UGATE PVCC PHASE ISL6612 PWM DRIVER +12V VCC DIFF VSEN BOOT UGATE EN_VTT PVCC VR_RDY ISL6306 ISEN1+ ISEN1- VID7 VIN VCC RGND VTT NTC THERMISTOR GND +5V FB COMP REF IDROOP DAC V LGATE VID6 PHASE ISL6612 PWM DRIVER PWM1 GND PWM2 VID5 LGATE ISEN2+ VID4 ISEN2VID3 PWM3 VID2 ISEN3+ +12V VIN PWM4 VID0 ISEN4+ ISEN4- µP LOAD VCC ISEN3VID1 BOOT UGATE PVCC PHASE VRSEL VR_FAN GND ISL6612 PWM DRIVER VR_HOT LGATE GND TM +5V EN_PWR TCOMP OFS FS SS +12V R OFS RT VIN VCC +12V BOOT NTC UGATE PVCC PWM PHASE ISL6612 DRIVER LGATE GND 4 FN9226.1 May 5, 2008 ISL6306 Typical Application - 4-Phase Buck Converter with rDS(ON) Sensing and Integrated TCOMP +12V VIN VCC BOOT UGATE PVCC PHASE ISL6612 PWM DRIVER GND +5V FB IDROOP COMP REF VDIFF DAC VSEN VCC LGATE +12V VCC BOOT VIN RGND VTT UGATE EN_VTT PVCC VR_RDY ISL6306 ISEN1+ ISEN1- VID7 VID6 PHASE ISL6612 PWM DRIVER PWM1 PWM2 VID5 LGATE GND ISEN2+ VID4 ISEN2- VID3 PWM3 VID2 ISEN3+ +12V VIN PWM4 VID0 ISEN4+ ISEN4- µP LOAD VCC ISEN3VID1 BOOT UGATE PVCC PHASE VRSEL VR_FAN GND ISL6612 PWM DRIVER VR_HOT LGATE GND EN_PWR TM TCOMP OFS +5V FS SS +5V R OFS RF RS +12V VIN VCC BOOT +12V NTC UGATE PVCC PWM PHASE ISL6612 DRIVER LGATE GND 5 FN9226.1 May 5, 2008 ISL6306 Typical Application - 4-Phase Buck Converter with DCR Sensing and External TCOMP +12V VIN VCC BOOT UGATE PVCC PHASE ISL6612 PWM DRIVER +12V VCC DIFF VSEN BOOT EN_VTT UGATE PVCC VR_RDY ISL6306 ISEN1+ ISEN1- VID7 VIN VCC RGND VTT NTC THERMISTOR GND +5V FB COMP REF IDROOP DAC V LGATE VID6 PHASE ISL6612 PWM DRIVER PWM1 VID5 PWM2 VID4 ISEN2+ ISEN2- VID3 PWM3 VID2 ISEN3+ +12V VIN BOOT PWM4 VID0 µP LOAD VCC ISEN3VID1 UGATE ISEN4+ ISEN4- PVCC GND PWM PHASE VRSEL VR_FAN LGATE GND ISL6612 DRIVER VR_HOT LGATE GND TM +5V EN_PWR TCOMP OFS FS SS +12V R OFS RT VIN VCC +12V BOOT NTC UGATE PVCC PWM PHASE ISL6612 DRIVER LGATE GND 6 FN9226.1 May 5, 2008 ISL6306 Typical Application - 4-Phase Buck Converter with DCR Sensing and Integrated TCOMP +12V VIN VCC BOOT UGATE PVCC PHASE ISL6612 PWM DRIVER GND +5V FB COMP REF IDROOP DAC V +12V VCC DIFF VSEN BOOT EN_VTT UGATE PVCC VR_RDY ISL6306 ISEN1+ ISEN1- VID7 VIN VCC RGND VTT LGATE VID6 PHASE ISL6612 PWM DRIVER PWM1 VID5 PWM2 VID4 VID3 ISEN2+ ISEN2PWM3 VID2 ISEN3+ +12V VIN VCC ISEN3VID1 PWM4 VID0 ISEN4+ ISEN4- PVCC GND PWM µP LOAD BOOT UGATE PHASE VRSEL VR_FAN LGATE GND ISL6612 DRIVER LGATE VR_HOT TM GND EN_PWR TCOMP OFS FS SS +5V +5V +12V R OFS RF RS VIN VCC BOOT +12V NTC UGATE PVCC PWM PHASE ISL6612 DRIVER LGATE GND 7 FN9226.1 May 5, 2008 ISL6306 Absolute Maximum Ratings Thermal Information Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+6V All Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.3V to VCC + 0.3V ESD Ratings Human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV Machine model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>200V Charged device model . . . . . . . . . . . . . . . . . . . . . . . . . . . . >1.5kV Thermal Resistance (Notes 1, 2) θJA (°C/W) θJC (°C/W) QFN Package. . . . . . . . . . . . . . . . . . . . 34 6.5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5% Ambient Temperature ISL6306CRZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C ISL6306IRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379 2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Operating Conditions: VCC = 5V, Unless Otherwise Specified PARAMETER TEST CONDITIONS MIN TYP MAX UNITS VCC SUPPLY CURRENT Nominal Supply VCC = 5VDC; EN_PWR = 5VDC; RT = 100kΩ, ISEN1 = ISEN2 = ISEN3 = ISEN4 = -70µA - 15 20 mA Shutdown Supply VCC = 5VDC; EN_PWR = 0VDC; RT = 100kΩ - 10 12 mA VCC Rising 4.3 4.5 4.7 V VCC Falling 3.7 3.9 4.2 V 0.850 0.875 0.910 V - 130 - mV Falling 0.720 0.745 0.775 V Rising 0.850 0.875 0.910 V - 130 - mV 0.720 0.745 0.775 V POWER-ON RESET AND ENABLE POR Threshold EN_PWR Threshold Rising Hysteresis EN_VTT Threshold Hysteresis Falling REFERENCE VOLTAGE AND DAC System Accuracy of ISL6306CRZ (VID = 1V to 1.6V, TJ = 0°C to +70°C) (Note 3) -0.5 - 0.5 %VID System Accuracy of ISL6306CRZ (VID = 0.5V to 1V, TJ = 0°C to +70°C) (Note 3) -0.9 - 0.9 %VID System Accuracy of ISL6306IRZ (VID = 1V to 1.6V, TJ = -40°C to +85°C) (Note 3) -0.6 - 0.6 %VID System Accuracy of ISL6306IRZ (VID = 0.5V to 1V, TJ = -40°C to +85°C) (Note 3) -1 - 1 %VID -60 -40 -20 µA VID Input Low Level - - 0.4 V VID Input High Level 0.8 - - V VRSEL Input Low Level - - 0.4 V VRSEL Input High Level 0.8 - - V VID Pull-up 8 FN9226.1 May 5, 2008 ISL6306 Electrical Specifications Operating Conditions: VCC = 5V, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS DAC Source Current - 4 7 mA DAC Sink Current - - 300 µA REF Source Current 45 50 55 µA REF Sink Current 45 50 55 µA 392 400 408 mV 1.568 1.600 1.632 V 388 400 412 mV 1.552 1.600 1.648 V 225 250 275 kHz 0.08 - 1.0 MHz - 1.563 - mV/µs 0.625 - 6.25 mV/µs Sawtooth Amplitude - 1.5 - V Max Duty Cycle - 66.7 - % PIN-ADJUSTABLE OFFSET Voltage at OFS Pin of ISL6306CRZ Offset resistor connected to ground Voltage below VCC, offset resistor connected to VCC Voltage at OFS Pin of ISL6306IRZ Offset resistor connected to ground Voltage below VCC, offset resistor connected to VCC OSCILLATORS Accuracy of Switching Frequency Setting RT = 100kΩ Adjustment Range of Switching Frequency (Note 4) Soft-Start Ramp Rate RS = 100kΩ (Notes 5, 6) Adjustment Range of Soft-start Ramp Rate (Note 4) PWM GENERATOR ERROR AMPLIFIER Open-Loop Gain RL = 10kΩ to ground (Note 4) - 96 - dB Open-Loop Bandwidth CL = 100pF, RL = 10kΩ to ground (Note 4) - 20 - MHz Slew Rate CL = 100pF - 9 - V/µs Maximum Output Voltage 3.8 4.3 4.9 V Output High Voltage @ 2mA 3.6 - - V Output Low Voltage @ 2mA - - 1.2 V - 20 - MHz REMOTE-SENSE AMPLIFIER Bandwidth (Note 4) Output High Current VSEN - RGND = 2.5V -500 - 500 µA Output High Current VSEN - RGND = 0.6 -500 - 500 µA PWM OUTPUT PWM Output Voltage LOW Threshold ILOAD = ±500µA - - 0.5 V PWM Output Voltage HIGH Threshold ILOAD = ±500µA 4.3 - - V 76 80 84 µA 90 100 110 µA - 2 - V TM Input Voltage for VR_FAN Trip 1.6 1.65 1.69 V TM Input Voltage for VR_FAN Reset 1.89 1.93 1.98 V TM Input Voltage for VR_HOT Trip 1.35 1.4 1.44 V TM Input Voltage for VR_HOT Reset 1.6 1.65 1.69 V SENSE CURRENT OUTPUT (IDROOP and IOUT) Sensed Current Tolerance ISEN1 = ISEN2 = ISEN3 = ISEN4 = 80µA Overcurrent Trip Level Maximum Voltage at IDROOP Pin THERMAL MONITORING AND FAN CONTROL 9 FN9226.1 May 5, 2008 ISL6306 Electrical Specifications Operating Conditions: VCC = 5V, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Leakage Current of VR_FAN With externally pull-up resistor connected to VCC - - 30 µA VR_FAN Low Voltage With 1.25k resistor pull-up to VCC, IVR_FAN = 4mA - - 0.3 V Leakage Current of VR_HOT With externally pull-up resistor connected to VCC - - 30 µA VR_HOT Low Voltage With 1.25k resistor pull-up to VCC, IVR_HOT = 4mA - - 0.3 V VR READY AND PROTECTION MONITORS Leakage Current of VR_RDY With externally pull-up resistor connected to VCC - - 30 µA VR_RDY Low Voltage IVR_RDY = 4mA - - 0.3 V Undervoltage Threshold VDIFF Falling 48 50 52 %VID VR_RDY Reset Voltage VDIFF Rising 58 60 62 %VID Overvoltage Protection Threshold Before valid VID 1.250 1.275 1.300 V 150 175 200 mV 0.38 0.40 0.42 V After valid VID, the voltage above VID Overvoltage Protection Reset Threshold NOTES: 3. These parts are designed and adjusted for accuracy with all errors in the voltage loop included. 4. Limits established by characterization and are not production tested. 5. During soft-start, VDAC rises from 0 to 1.1V first and then ramp to VID voltage after receiving valid VID. 6. Soft-start ramp rate is determined by the adjustable soft-start oscillator frequency at the speed of 6.25mV per cycle. 10 FN9226.1 May 5, 2008 ISL6306 Functional Pin Description VCC Supplies the power necessary to operate the chip. The controller starts to operate when the voltage on this pin exceeds the rising POR threshold and shuts down when the voltage on this pin drops below the falling POR threshold. Connect this pin directly to a +5V supply. GND Bias and reference ground for the IC. The bottom metal base of ISL6306 is the GND. EN_PWR VRSEL Use this pin to select Internal VID code. When it is connected to GND, the extended VR10 code is selected. When it’s floated or pulled to high, VR11 code is selected. This input can be pulled up as high as VCC plus 0.3V. VDIFF, VSEN, and RGND VSEN and RGND form the precision differential remote-sense amplifier. This amplifier converts the differential voltage of the remote output to a single-ended voltage referenced to local ground. VDIFF is the amplifier’s output and the input to the regulation and protection circuitry. Connect VSEN and RGND to the sense pins of the remote load. This pin is a threshold-sensitive enable input for the controller. Connecting the 12V supply to EN_PWR through an appropriate resistor divider provides a means to synchronize power-up of the controller and the MOSFET driver ICs. When EN_PWR is driven above 0.875V, the ISL6306 is active depending on status of EN_VTT, the internal POR, and pending fault states. Driving EN_PWR below 0.745V will clear all fault states and prime the ISL6306 to soft-start when re-enabled. FB and COMP EN_VTT This pin is another threshold-sensitive enable input for the controller. It’s typically connected to VTT output of VTT voltage regulator in the computer mother board. When EN_VTT is driven above 0.875V, the ISL6306 is active depending on status of ENLL, the internal POR, and pending fault states. Driving EN_VTT below 0.745V will clear all fault states and prime the ISL6306 to soft-start when re-enabled. The DAC pin is the output of the precision internal DAC reference. The REF pin is the positive input of the Error Amplifier. In typical applications, a 1kΩ, 1% resistor is used between DAC and REF to generate a precision offset voltage. This voltage is proportional to the offset current determined by the offset resistor from OFS to ground or VCC. A capacitor is used between REF and ground to smooth the voltage transition during Dynamic VID™ operations. FS PWM1, PWM2, PWM3, PWM4 Use this pin to set up the desired switching frequency. A resistor, placed from FS to ground will set the switching frequency. The relationship between the value of the resistor and the switching frequency will be described by an approximate equation. Pulse width modulation outputs. Connect these pins to the PWM input pins of the Intersil driver IC. The number of active channels is determined by the state of PWM3 and PWM4. Tie PWM3 to VCC to configure for 2-phase operation. Tie PWM4 to VCC to configure for 3-phase operation. SS ISEN1+, ISEN1-; ISEN2+, ISEN2-; ISEN3+, ISEN3-; ISEN4+ and ISEN4 Use this pin to set up the desired start-up oscillator frequency. A resistor, placed from SS to ground will set up the soft-start ramp rate. The relationship between the value of the resistor and the soft-start ramp-up time will be described by an approximate equation. VID7, VID6, VID5, VID4, VID3, VID2, VID1 and VID0 These are the inputs to the internal DAC that generates the reference voltage for output regulation. Connect these pins either to open-drain outputs with or without external pull-up resistors or to active pull-up outputs. All VID pins have 40µA internal pull-up current sources that diminish to zero as the voltage rises above the logic-high level. These inputs can be pulled up externally as high as VCC plus 0.3V. When an OFF VID code causes shut-down, the controller needs to be reset before it starts again. 11 Inverting input and output of the error amplifier respectively. FB can be connected to VDIFF through a resistor. A properly chosen resistor between VDIFF and FB can set the load line (droop), when IDROOP pin is tied to FB pin. The droop scale factor is set by the ratio of the ISEN resistors and the inductor DCR or the lower MOSFET rDS(ON). COMP is tied back to FB through an external RC network to compensate the regulator. DAC and REF The ISEN+ and ISEN- pins are current sense inputs to individual differential amplifiers. The sensed current is used for channel current balancing, overcurrent protection, and droop regulation. Inactive channels should have their respective current sense inputs left open (for example, open ISEN4+ and ISEN4- for 3-phase operation). For DCR sensing, connect each ISEN- pin to the node between the RC sense elements. Tie the ISEN+ pin to the other end of the sense capacitor through a resistor, RISEN. The voltage across the sense capacitor is proportional to the inductor current. Therefore, the sense current is proportional to the inductor current and scaled by the DCR of the inductor and RISEN. FN9226.1 May 5, 2008 ISL6306 When configured for rDS(ON) current sensing, the ISEN1-, ISEN2-, ISEN3-, and ISEN4- pins are grounded at the lower MOSFET sources. The ISEN1+, ISEN2+, ISEN3+, and ISEN4+ pins are then held at a virtual ground. Therefore, a resistor, connected between these current sense pins and the drain terminals of the associated lower MOSFET, will carry the current proportional to the current flowing through that channel. The sensed current is determined by the negative voltage across the lower MOSFET when it is ON, which is the channel current scaled by rDS(ON) and RISEN. VR_RDY VR_RDY indicates that the soft-start is completed and the output voltage is within the regulated range around VID setting. It is an open-drain logic output. When OCP or OVP occurs, VR_RDY will be pulled to low. It will also be pulled low if the output voltage is below the undervoltage threshold. OFS The OFS pin provides a means to program a DC offset current for generating a DC offset voltage at the REF input. The offset current is generated via an external resistor and precision internal voltage references. The polarity of the offset is selected by connecting the resistor to GND or VCC. For no offset, the OFS pin should be left unterminated. VR_HOT VR_HOT is used as an indication of high VR temperature. It is an open-drain logic output. It will be open when the measured VR temperature reaches a certain level. VR_FAN VR_FAN is an output pin with open-drain logic output. It will be open when the measured VR temperature reaches a certain level. Operation Multiphase Power Conversion Microprocessor load current profiles have changed to the point that the advantages of multiphase power conversion are impossible to ignore. The technical challenges associated with producing a single-phase converter which is both cost-effective and thermally viable have forced a change to the cost-saving approach of multiphase. The ISL6306 controller helps reduce the complexity of implementation by integrating vital functions and requiring minimal output components. The block diagrams on pages 4, 5, 6 and 7 provide top level views of multiphase power conversion using the ISL6306 controller. TCOMP Interleaving Temperature compensation scaling input. The voltage sensed on the TM pin is utilized as the temperature input to adjust ldroop and the overcurrent protection limit to effectively compensate for the temperature coefficient of the current sense element. To implement the integrated temperature compensation, a resistor divider circuit is needed with one resistor being connected from TCOMP to VCC of the controller and another resistor being connected from TCOMP to GND. Changing the ratio of the resistor values will set the gain of the integrated thermal compensation. When integrated temperature compensation function is not used, connect TCOMP to GND. The switching of each channel in a multiphase converter is timed to be symmetrically out of phase with each of the other channels. In a 3-phase converter, each channel switches 1/3 cycle after the previous channel and 1/3 cycle before the following channel. As a result, the 3-phase converter has a combined ripple frequency three times greater than the ripple frequency of any one phase. In addition, the peak-topeak amplitude of the combined inductor currents is reduced in proportion to the number of phases (Equations 1 and 2). Increased ripple frequency and lower ripple amplitude mean that the designer can use less per-channel inductance and lower total output capacitance for any performance specification. IDROOP IDROOP is the output pin of sensed average channel current which is proportional to load current. In the application which does not require loadline, leave this pin open. In the application which requires load line, connect this pin to FB so that the sensed average current will flow through the resistor between FB and VDIFF to create a voltage drop which is proportional to load current. TM Figure 1 illustrates the multiplicative effect on output ripple frequency. The three channel currents (IL1, IL2, and IL3) combine to form the AC ripple current and the DC load current. The ripple component has three times the ripple frequency of each individual channel current. Each PWM pulse is terminated 1/3 of a cycle after the PWM pulse of the previous phase. The peak-to-peak current for each phase is about 7A, and the DC components of the inductor currents combine to feed the load. TM is an input pin for VR temperature measurement. Connect this pin through NTC thermistor to GND and a resistor to VCC of the controller. The voltage at this pin is reverse proportional to VR temperature. ISL6306 monitors the VR temperature based on the voltage at TM pin and outputs VR_HOT and VR_FAN signals. 12 FN9226.1 May 5, 2008 ISL6306 ( V IN – N V OUT ) V OUT I C, P-P = ----------------------------------------------------------L fS V IL1 + IL2 + IL3, 7A/DIV Another benefit of interleaving is to reduce input ripple current. Input capacitance is determined in part by the maximum input ripple current. Multiphase topologies can improve overall system cost and size by lowering input ripple current and allowing the designer to reduce the cost of input capacitance. The example in Figure 2 illustrates input currents from a 3-phase converter combining to reduce the total input ripple current. IL1, 7A/DIV PWM1, 5V/DIV IL2, 7A/DIV PWM2, 5V/DIV IL3, 7A/DIV PWM3, 5V/DIV 1µs/DIV FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS FOR 3-PHASE CONVERTER To understand the reduction of ripple current amplitude in the multiphase circuit, examine Equation 1 which represents an individual channel’s peak-to-peak inductor current. ( V IN – V OUT ) V OUT I P-P = ----------------------------------------------------L fS V (EQ. 1) IN In Equation 1, VIN and VOUT are the input and output voltages respectively, L is the single-channel inductor value, and fS is the switching frequency. INPUT-CAPACITOR CURRENT, 10A/DIV CHANNEL 1 INPUT CURRENT 10A/DIV CHANNEL 2 INPUT CURRENT 10A/DIV CHANNEL 3 INPUT CURRENT 10A/DIV 1µs/DIV FIGURE 2. CHANNEL INPUT CURRENTS AND INPUTCAPACITOR RMS CURRENT FOR THREE-PHASE CONVERTER The output capacitors conduct the ripple component of the inductor current. In the case of multiphase converters, the capacitor current is the sum of the ripple currents from each of the individual channels. Compare Equation 1 to the expression for the peak-to-peak current after the summation of N symmetrically phase-shifted inductor currents in Equation 2. Peak-to-peak ripple current decreases by an amount proportional to the number of channels. Output voltage ripple is a function of capacitance, capacitor equivalent series resistance (ESR), and inductor ripple current. Reducing the inductor ripple current allows the designer to use fewer or less costly output capacitors. 13 (EQ. 2) IN The converter depicted in Figure 2 delivers 36A to a 1.5V load from a 12V input. The RMS input capacitor current is 5.9A. Compare this to a single-phase converter also stepping down 12V to 1.5V at 36A. The single-phase converter has 11.9A RMS input capacitor current. The single-phase converter must use an input capacitor bank with twice the RMS current capacity as the equivalent 3-phase converter. Figures 21, 22 and 23 in the section entitled “Input Capacitor Selection” on page 30, can be used to determine the inputcapacitor RMS current based on load current, duty cycle, and the number of channels. They are provided as aids in determining the optimal input capacitor solution. Figure 23 shows the single-phase input-capacitor RMS current for comparison. PWM Operation The timing of each channel is set by the number of active channels. The default channel setting for the ISL6306 is four. The switching cycle is defined as the time between PWM pulse termination signals of each channel. The pulse termination signal is an internally generated clock signal which triggers the falling edge of PWM signal. The cycle time of the pulse termination signal is the inverse of the switching frequency set by the resistor between the FS pin and ground. Each cycle begins when the clock signal commands the channel PWM signal to go low. The PWM signals command the MOSFET driver to turn on/off the channel MOSFETs. For 4-channel operation, the channel firing order is 4-3-2-1: PWM3 pulse terminates 1/4 of a cycle after PWM4, PWM2 output follows another 1/4 of a cycle after PWM3, and PWM1 terminates another 1/4 of a cycle after PWM2. For 3-channel operation, the channel firing order is 3-2-1. Connecting PWM4 to VCC selects three channel operation and the pulse-termination times are spaced in 1/3 cycle increments. If PWM3 is connected to VCC, two channel operation is selected and the PWM2 pulse terminates 1/2 of a cycle later. Once a PWM signal transitions low, it is held low for a minimum of 1/3 cycle. This forced off time is required to ensure an accurate current sample. Current sensing is described in the next section. After the forced off time expires, the PWM output is enabled. The PWM output state FN9226.1 May 5, 2008 ISL6306 is driven by the position of the error amplifier output signal, VCOMP, minus the current correction signal relative to the sawtooth ramp as illustrated in Figure 7. When the modified VCOMP voltage crosses the sawtooth ramp, the PWM output transitions high. The MOSFET driver detects the change in state of the PWM signal and turns off the synchronous MOSFET and turns on the upper MOSFET. The PWM signal will remain high until the pulse termination signal marks the beginning of the next cycle by triggering the PWM signal low. INDUCTOR DCR SENSING An inductor’s winding is characteristic of a distributed resistance as measured by the DCR (Direct Current Resistance) parameter. Consider the inductor DCR as a separate lumped quantity, as shown in Figure 4. The channel current (IL) flowing through the inductor, will also pass through the DCR. Equation 3 shows the s-domain equivalent voltage across the inductor VL. V L = I L ⋅ ( s ⋅ L + DCR ) During the forced off-time following a PWM transition low, the associated channel current sense amplifier uses the ISEN inputs to reproduce a signal proportional to the inductor current (IL). This current gets sampled starting 1/6 period after each PWM goes low and continuously gets sampled for 1/3 period, or until the PWM goes high, whichever comes first. No matter the current sense method, the sense current (ISEN) is simply a scaled version of the inductor current. Coincident with the falling edge of the PWM signal, the sample and hold circuitry samples the sensed current signal (ISEN) as illustrated in Figure 3. Therefore, the sample current (In) is proportional to the output current and held for one switching cycle. The sample current is used for current balance, load-line regulation, and overcurrent protection. (EQ. 3) A simple RC network across the inductor extracts the DCR voltage, as shown in Figure 4. The voltage on the capacitor (VC) can be shown to be proportional to the channel current (IL) see Equation 4. L ⎛ s ⋅ ------------+ 1⎞ ⋅ ( DCR ⋅ I L ) ⎝ DCR ⎠ V C = --------------------------------------------------------------------( s ⋅ RC + 1 ) (EQ. 4) If the RC network components are selected such that the RC time constant (= R*C) matches the inductor time constant (= L/DCR), the voltage across the capacitor (VC) is equal to the voltage drop across the DCR (i.e., proportional to the channel current). VIN IL ( s ) L IL ISL6605 DCR + INDUCTOR VL VOUT COUT - Current Sampling PWM + R - VC(s) C PWM(n) ISEN ISL6306 INTERNAL CIRCUIT 0.5Tsw SAMPLE CURRENT, In SWITCHING PERIOD RISEN(n) (PTC) In SAMPLE AND HOLD ISEN-(n) + TIME - FIGURE 3. SAMPLE AND HOLD TIMING Current Sensing The ISL6306 supports inductor DCR sensing, MOSFET rDS(ON) sensing, or resistive sensing techniques. The internal circuitry, shown in Figures 4, 5, and 6, represents one channel of an N-channel converter. This circuitry is repeated for each channel in the converter, but may not be active depending on the status of the PWM3 and PWM4 pins, as described in “PWM Operation” on page 13. 14 ISEN+(n) DCR I SEN = I ----------------LR ISEN FIGURE 4. DCR SENSING CONFIGURATION With the internal low-offset current amplifier, the capacitor voltage (VC) is replicated across the sense resistor (RISEN). Therefore the current out of ISEN+ pin (ISEN) is proportional to the inductor current. FN9226.1 May 5, 2008 ISL6306 Equation 5 shows that the ratio of the channel current to the sensed current (ISEN) is driven by the value of the sense resistor and the DCR of the inductor. DCR I SEN = I L ⋅ -----------------R (EQ. 5) I VIN R DS ( ON ) SEN = I L --------------------------R ISEN In IL ISEN SAMPLE AND HOLD RESISTIVE SENSING For accurate current sense, a dedicated current-sense resistor (RSENSE) in series with each output inductor can serve as the current sense element (see Figure 5). This technique is more accurate, but reduces overall converter efficiency due to the additional power loss on the current sense element (RSENSE). ISEN+(n) RISEN (PTC) + N-CHANNEL MOSFETs ISL6306 INTERNAL CIRCUIT Equation 6 shows the ratio of the channel current to the sensed current (ISEN). R SENSE I SEN = I L ⋅ ----------------------R (EQ. 6) ISEN L IL RSENSE VOUT ISEN-(n) I x R λ DS ( ON ) L + EXTERNAL CIRCUIT FIGURE 6. MOSFET rDS(ON) CURRENT-SENSING CIRCUIT Equation 7 shows the ratio of the channel current to the sensed current ISEN. R DS ( ON ) I SEN = I L -----------------------R ISEN (EQ. 7) COUT ISL6306 INTERNAL CIRCUIT RISEN(n) In SAMPLE AND HOLD ISEN-(n) + - ISEN+(n) R SENSE I SEN = I ------------------------L R ISEN Both inductor DCR and MOSFET rDS(ON) value will increase as the temperature increases. Therefore the sensed current will increase as the temperature of the current sense element increases. In order to compensate the temperature effect on the sensed current signal, a Positive Temperature Coefficient (PTC) resistor can be selected for the sense resistor (RISEN), or the integrated temperature compensation function of ISL6306 should be utilized. The integrated temperature compensation function is described in “Temperature Compensation” on page 25. Channel-Current Balance FIGURE 5. SENSE RESISTOR IN SERIES WITH INDUCTORS MOSFET rDS(ON) SENSING The controller can also sense the channel load current by sampling the voltage across the lower MOSFET rDS(ON) (see Figure 6). The amplifier is ground-reference by connecting the ISEN- pin to the source of the lower MOSFET. ISEN+ pin is connected to the PHASE node through the current sense resistor (RISEN). The voltage across RISEN is equivalent to the voltage drop across the rDS(ON) of the lower MOSFET while it is conducting. The resulting current out of the ISEN+ pin is proportional to the channel current IL. 15 The sensed current (IN) from each active channel are summed together and divided by the number of active channels. The resulting average current (IAVG) provides a measure of the total load current. Channel current balance is achieved by comparing the sampled current of each channel to the average current to make an appropriate adjustment to the WPM duty cycle of each channel. Intersil’s patented current-balance method is illustrated in Figure 7. In the figure, the average current combines with the Channel 1 current (I1) to create an error signal (IER). The filtered error signal modifies the pulse width commanded by VCOMP to correct any unbalance and force IER toward zero. The same method for error signal correction is applied to each active channel. FN9226.1 May 5, 2008 ISL6306 VCOMP + + - FILTER PWM1 SAWTOOTH SIGNAL f(jω) I4 * IER IAVG - ÷N + Σ I3 * I2 I1 NOTE: *Channels 3 and 4 are optional for 2 or 3 phase designs. FIGURE 7. CHANNEL 1 PWM FUNCTION AND CURRENTBALANCE ADJUSTMENT Channel current balance is essential in achieving the thermal advantage of multiphase operation. With good current balance, the power loss is equally dissipated over multiple devices and a greater area. Voltage Regulation The ISL6306 incorporates an internal differential remotesense amplifier in the feedback path. The amplifier removes the voltage error encountered when measuring the output voltage relative to the local controller ground reference point resulting in a more accurate means of sensing output voltage. Connect the microprocessor sense pins to the noninverting input, VSEN, and inverting input, RGND, of the remote-sense amplifier. The remote-sense output (VDIF), is connected to the inverting input of the error amplifier through an external resistor. A digital-to-analog converter (DAC) generates a reference voltage based on the state of logic signals at pins VID7 through VID0. The DAC decodes the 8 6-bit logic signal (VID) into one of the discrete voltages shown in Table 1. Each VID input offers a 45µA pull-up to an internal 2.5V source for use with open-drain outputs. The pull-up current diminishes to zero above the logic threshold to protect voltage-sensitive output devices. External pull-up resistors can augment the pull-up current sources if case leakage into the driving device is greater than 45µA. The compensation network shown in Figure 8 assures that the steady-state error in the output voltage is limited only to the error in the reference voltage (output of the DAC) and offset errors in the OFS current source, remote-sense and error amplifiers. Intersil specifies the guaranteed tolerance of the ISL6306 to include the combined tolerances of each of these elements. The output of the error amplifier (VCOMP) is compared to the sawtooth waveform to generate the PWM signals. The PWM signals control the timing of the Intersil MOSFET drivers and regulate the converter output to the specified reference voltage. The internal and external circuitry, which control voltage regulation, are illustrated in Figure 8. EXTERNAL CIRCUIT R C CC COMP ISL6306 INTERNAL CIRCUIT DAC RREF REF CREF + - FB RFB IDROOP + VDROOP VDIFF VOUT+ VOUT- IAVG VCOMP ERROR AMPLIFIER VSEN + RGND DIFFERENTIAL REMOTE-SENSE AMPLIFIER FIGURE 8. OUTPUT VOLTAGE AND LOAD-LINE REGULATION WITH OFFSET ADJUSTMENT 16 FN9226.1 May 5, 2008 ISL6306 TABLE 1. VR10 VID TABLE (WITH 6.25mV EXTENSION) VID4 VID3 VID2 VID1 VID0 VID5 VID6 VOLTAGE 400mV 200mV 100mV 50mV 25mV 12.5mV 6.25mV (V) TABLE 1. VR10 VID TABLE (WITH 6.25mV EXTENSION) (Continued) VID4 VID3 VID2 VID1 VID0 VID5 VID6 VOLTAGE 400mV 200mV 100mV 50mV 25mV 12.5mV 6.25mV (V) 0 1 0 1 0 1 1 1.60000 1 0 1 0 0 0 1 1.36250 0 1 0 1 0 1 0 1.59375 1 0 1 0 0 0 0 1.35625 0 1 0 1 1 0 1 1.58750 1 0 1 0 0 1 1 1.35000 0 1 0 1 1 0 0 1.58125 1 0 1 0 0 1 0 1.34375 0 1 0 1 1 1 1 1.57500 1 0 1 0 1 0 1 1.33750 0 1 0 1 1 1 0 1.56875 1 0 1 0 1 0 0 1.33125 0 1 1 0 0 0 1 1.56250 1 0 1 0 1 1 1 1.32500 0 1 1 0 0 0 0 1.55625 1 0 1 0 1 1 0 1.31875 0 1 1 0 0 1 1 1.55000 1 0 1 1 0 0 1 1.31250 0 1 1 0 0 1 0 1.54375 1 0 1 1 0 0 0 1.30625 0 1 1 0 1 0 1 1.53750 1 0 1 1 0 1 1 1.30000 0 1 1 0 1 0 0 1.53125 1 0 1 1 0 1 0 1.29375 0 1 1 0 1 1 1 1.52500 1 0 1 1 1 0 1 1.28750 0 1 1 0 1 1 0 1.51875 1 0 1 1 1 0 0 1.28125 0 1 1 1 0 0 1 1.51250 1 0 1 1 1 1 1 1.27500 0 1 1 1 0 0 0 1.50625 1 0 1 1 1 1 0 1.26875 0 1 1 1 0 1 1 1.50000 1 1 0 0 0 0 1 1.26250 0 1 1 1 0 1 0 1.49375 1 1 0 0 0 0 0 1.25625 0 1 1 1 1 0 1 1.48750 1 1 0 0 0 1 1 1.25000 0 1 1 1 1 0 0 1.48125 1 1 0 0 0 1 0 1.24375 0 1 1 1 1 1 1 1.47500 1 1 0 0 1 0 1 1.23750 0 1 1 1 1 1 0 1.46875 1 1 0 0 1 0 0 1.23125 1 0 0 0 0 0 1 1.46250 1 1 0 0 1 1 1 1.22500 1 0 0 0 0 0 0 1.45625 1 1 0 0 1 1 0 1.21875 1 0 0 0 0 1 1 1.45000 1 1 0 1 0 0 1 1.21250 1 0 0 0 0 1 0 1.44375 1 1 0 1 0 0 0 1.20625 1 0 0 0 1 0 1 1.43750 1 1 0 1 0 1 1 1.20000 1 0 0 0 1 0 0 1.43125 1 1 0 1 0 1 0 1.19375 1 0 0 0 1 1 1 1.42500 1 1 0 1 1 0 1 1.18750 1 0 0 0 1 1 0 1.41875 1 1 0 1 1 0 0 1.18125 1 0 0 1 0 0 1 1.41250 1 1 0 1 1 1 1 1.17500 1 0 0 1 0 0 0 1.40625 1 1 0 1 1 1 0 1.16875 1 0 0 1 0 1 1 1.40000 1 1 1 0 0 0 1 1.16250 1 0 0 1 0 1 0 1.39375 1 1 1 0 0 0 0 1.15625 1 0 0 1 1 0 1 1.38750 1 1 1 0 0 1 1 1.15000 1 0 0 1 1 0 0 1.38125 1 1 1 0 0 1 0 1.14375 1 0 0 1 1 1 1 1.37500 1 1 1 0 1 0 1 1.13750 1 0 0 1 1 1 0 1.36875 1 1 1 0 1 0 0 1.13125 1 1 1 0 1 1 1 1.12500 17 FN9226.1 May 5, 2008 ISL6306 TABLE 1. VR10 VID TABLE (WITH 6.25mV EXTENSION) (Continued) VID4 VID3 VID2 VID1 VID0 VID5 VID6 VOLTAGE 400mV 200mV 100mV 50mV 25mV 12.5mV 6.25mV (V) TABLE 1. VR10 VID TABLE (WITH 6.25mV EXTENSION) (Continued) VID4 VID3 VID2 VID1 VID0 VID5 VID6 VOLTAGE 400mV 200mV 100mV 50mV 25mV 12.5mV 6.25mV (V) 1 1 1 0 1 1 0 1.11875 0 0 1 1 1 1 1 0.90000 1 1 1 1 0 0 1 1.11250 0 0 1 1 1 1 0 0.89375 1 1 1 1 0 0 0 1.10625 0 1 0 0 0 0 1 0.88750 1 1 1 1 0 1 1 1.10000 0 1 0 0 0 0 0 0.88125 1 1 1 1 0 1 0 1.09375 0 1 0 0 0 1 1 0.87500 1 1 1 1 1 0 1 OFF 0 1 0 0 0 1 0 0.86875 1 1 1 1 1 0 0 OFF 0 1 0 0 1 0 1 0.86250 1 1 1 1 1 1 1 OFF 0 1 0 0 1 0 0 0.85625 1 1 1 1 1 1 0 OFF 0 1 0 0 1 1 1 0.85000 0 0 0 0 0 0 1 1.08750 0 1 0 0 1 1 0 0.84375 0 0 0 0 0 0 0 1.08125 0 1 0 1 0 0 1 0.83750 0 0 0 0 0 1 1 1.07500 0 1 0 1 0 0 0 0.83125 0 0 0 0 0 1 0 1.06875 0 0 0 0 1 0 1 1.06250 0 0 0 0 1 0 0 1.05625 0 0 0 0 1 1 1 1.05000 0 0 0 0 1 1 0 1.04375 0 0 0 1 0 0 1 1.03750 0 0 0 1 0 0 0 1.03125 0 0 0 1 0 1 1 1.02500 0 0 0 1 0 1 0 1.01875 0 0 0 1 1 0 1 1.01250 0 0 0 1 1 0 0 1.00625 0 0 0 1 1 1 1 1.00000 0 0 0 1 1 1 0 0.99375 0 0 1 0 0 0 1 0.98750 0 0 1 0 0 0 0 0.98125 0 0 1 0 0 1 1 0.97500 0 0 1 0 0 1 0 0.96875 0 0 1 0 1 0 1 0.96250 0 0 1 0 1 0 0 0.95625 0 0 1 0 1 1 1 0.95000 0 0 1 0 1 1 0 0.94375 0 0 1 1 0 0 1 0.93750 0 0 1 1 0 0 0 0.93125 0 0 1 1 0 1 1 0.92500 0 0 1 1 0 1 0 0.91875 0 0 1 1 1 0 1 0.91250 0 0 1 1 1 0 0 0.90625 18 TABLE 2. VR11 VID 8 BIT VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VOLTAGE 0 0 0 0 0 0 0 0 OFF 0 0 0 0 0 0 0 1 OFF 0 0 0 0 0 0 1 0 1.60000 0 0 0 0 0 0 1 1 1.59375 0 0 0 0 0 1 0 0 1.58750 0 0 0 0 0 1 0 1 1.58125 0 0 0 0 0 1 1 0 1.57500 0 0 0 0 0 1 1 1 1.56875 0 0 0 0 1 0 0 0 1.56250 0 0 0 0 1 0 0 1 1.55625 0 0 0 0 1 0 1 0 1.55000 0 0 0 0 1 0 1 1 1.54375 0 0 0 0 1 1 0 0 1.53750 0 0 0 0 1 1 0 1 1.53125 0 0 0 0 1 1 1 0 1.52500 0 0 0 0 1 1 1 1 1.51875 0 0 0 1 0 0 0 0 1.51250 0 0 0 1 0 0 0 1 1.50625 0 0 0 1 0 0 1 0 1.50000 0 0 0 1 0 0 1 1 1.49375 0 0 0 1 0 1 0 0 1.48750 0 0 0 1 0 1 0 1 1.48125 0 0 0 1 0 1 1 0 1.47500 0 0 0 1 0 1 1 1 1.46875 FN9226.1 May 5, 2008 ISL6306 TABLE 2. VR11 VID 8 BIT (Continued) TABLE 2. VR11 VID 8 BIT (Continued) VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VOLTAGE VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VOLTAGE 0 0 0 1 1 0 0 0 1.46250 0 1 0 0 0 0 0 0 1.21250 0 0 0 1 1 0 0 1 1.45625 0 1 0 0 0 0 0 1 1.20625 0 0 0 1 1 0 1 0 1.45000 0 1 0 0 0 0 1 0 1.20000 0 0 0 1 1 0 1 1 1.44375 0 1 0 0 0 0 1 1 1.19375 0 0 0 1 1 1 0 0 1.43750 0 1 0 0 0 1 0 0 1.18750 0 0 0 1 1 1 0 1 1.43125 0 1 0 0 0 1 0 1 1.18125 0 0 0 1 1 1 1 0 1.42500 0 1 0 0 0 1 1 0 1.17500 0 0 0 1 1 1 1 1 1.41875 0 1 0 0 0 1 1 1 1.16875 0 0 1 0 0 0 0 0 1.41250 0 1 0 0 1 0 0 0 1.16250 0 0 1 0 0 0 0 1 1.40625 0 1 0 0 1 0 0 1 1.15625 0 0 1 0 0 0 1 0 1.40000 0 1 0 0 1 0 1 0 1.15000 0 0 1 0 0 0 1 1 1.39375 0 1 0 0 1 0 1 1 1.14375 0 0 1 0 0 1 0 0 1.38750 0 1 0 0 1 1 0 0 1.13750 0 0 1 0 0 1 0 1 1.38125 0 1 0 0 1 1 0 1 1.13125 0 0 1 0 0 1 1 0 1.37500 0 1 0 0 1 1 1 0 1.12500 0 0 1 0 0 1 1 1 1.36875 0 1 0 0 1 1 1 1 1.11875 0 0 1 0 1 0 0 0 1.36250 0 1 0 1 0 0 0 0 1.11250 0 0 1 0 1 0 0 1 1.35625 0 1 0 1 0 0 0 1 1.10625 0 0 1 0 1 0 1 0 1.35000 0 1 0 1 0 0 1 0 1.10000 0 0 1 0 1 0 1 1 1.34375 0 1 0 1 0 0 1 1 1.09375 0 0 1 0 1 1 0 0 1.33750 0 1 0 1 0 1 0 0 1.08750 0 0 1 0 1 1 0 1 1.33125 0 1 0 1 0 1 0 1 1.08125 0 0 1 0 1 1 1 0 1.32500 0 1 0 1 0 1 1 0 1.07500 0 0 1 0 1 1 1 1 1.31875 0 1 0 1 0 1 1 1 1.06875 0 0 1 1 0 0 0 0 1.31250 0 1 0 1 1 0 0 0 1.06250 0 0 1 1 0 0 0 1 1.30625 0 1 0 1 1 0 0 1 1.05625 0 0 1 1 0 0 1 0 1.30000 0 1 0 1 1 0 1 0 1.05000 0 0 1 1 0 0 1 1 1.29375 0 1 0 1 1 0 1 1 1.04375 0 0 1 1 0 1 0 0 1.28750 0 1 0 1 1 1 0 0 1.03750 0 0 1 1 0 1 0 1 1.28125 0 1 0 1 1 1 0 1 1.03125 0 0 1 1 0 1 1 0 1.27500 0 1 0 1 1 1 1 0 1.02500 0 0 1 1 0 1 1 1 1.26875 0 1 0 1 1 1 1 1 1.01875 0 0 1 1 1 0 0 0 1.26250 0 1 1 0 0 0 0 0 1.01250 0 0 1 1 1 0 0 1 1.25625 0 1 1 0 0 0 0 1 1.00625 0 0 1 1 1 0 1 0 1.25000 0 1 1 0 0 0 1 0 1.00000 0 0 1 1 1 0 1 1 1.24375 0 1 1 0 0 0 1 1 0.99375 0 0 1 1 1 1 0 0 1.23750 0 1 1 0 0 1 0 0 0.98750 0 0 1 1 1 1 0 1 1.23125 0 1 1 0 0 1 0 1 0.98125 0 0 1 1 1 1 1 0 1.22500 0 1 1 0 0 1 1 0 0.97500 0 0 1 1 1 1 1 1 1.21875 0 1 1 0 0 1 1 1 0.96875 19 FN9226.1 May 5, 2008 ISL6306 TABLE 2. VR11 VID 8 BIT (Continued) TABLE 2. VR11 VID 8 BIT (Continued) VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VOLTAGE VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VOLTAGE 0 1 1 0 1 0 0 0 0.96250 1 0 0 1 0 0 0 0 0.71250 0 1 1 0 1 0 0 1 0.95625 1 0 0 1 0 0 0 1 0.70625 0 1 1 0 1 0 1 0 0.95000 1 0 0 1 0 0 1 0 0.70000 0 1 1 0 1 0 1 1 0.94375 1 0 0 1 0 0 1 1 0.69375 0 1 1 0 1 1 0 0 0.93750 1 0 0 1 0 1 0 0 0.68750 0 1 1 0 1 1 0 1 0.93125 1 0 0 1 0 1 0 1 0.68125 0 1 1 0 1 1 1 0 0.92500 1 0 0 1 0 1 1 0 0.67500 0 1 1 0 1 1 1 1 0.91875 1 0 0 1 0 1 1 1 0.66875 0 1 1 1 0 0 0 0 0.91250 1 0 0 1 1 0 0 0 0.66250 0 1 1 1 0 0 0 1 0.90625 1 0 0 1 1 0 0 1 0.65625 0 1 1 1 0 0 1 0 0.90000 1 0 0 1 1 0 1 0 0.65000 0 1 1 1 0 0 1 1 0.89375 1 0 0 1 1 0 1 1 0.64375 0 1 1 1 0 1 0 0 0.88750 1 0 0 1 1 1 0 0 0.63750 0 1 1 1 0 1 0 1 0.88125 1 0 0 1 1 1 0 1 0.63125 0 1 1 1 0 1 1 0 0.87500 1 0 0 1 1 1 1 0 0.62500 0 1 1 1 0 1 1 1 0.86875 1 0 0 1 1 1 1 1 0.61875 0 1 1 1 1 0 0 0 0.86250 1 0 1 0 0 0 0 0 0.61250 0 1 1 1 1 0 0 1 0.85625 1 0 1 0 0 0 0 1 0.60625 0 1 1 1 1 0 1 0 0.85000 1 0 1 0 0 0 1 0 0.60000 0 1 1 1 1 0 1 1 0.84375 1 0 1 0 0 0 1 1 0.59375 0 1 1 1 1 1 0 0 0.83750 1 0 1 0 0 1 0 0 0.58750 0 1 1 1 1 1 0 1 0.83125 1 0 1 0 0 1 0 1 0.58125 0 1 1 1 1 1 1 0 0.82500 1 0 1 0 0 1 1 0 0.57500 0 1 1 1 1 1 1 1 0.81875 1 0 1 0 0 1 1 1 0.56875 1 0 0 0 0 0 0 0 0.81250 1 0 1 0 1 0 0 0 0.56250 1 0 0 0 0 0 0 1 0.80625 1 0 1 0 1 0 0 1 0.55625 1 0 0 0 0 0 1 0 0.80000 1 0 1 0 1 0 1 0 0.55000 1 0 0 0 0 0 1 1 0.79375 1 0 1 0 1 0 1 1 0.54375 1 0 0 0 0 1 0 0 0.78750 1 0 1 0 1 1 0 0 0.53750 1 0 0 0 0 1 0 1 0.78125 1 0 1 0 1 1 0 1 0.53125 1 0 0 0 0 1 1 0 0.77500 1 0 1 0 1 1 1 0 0.52500 1 0 0 0 0 1 1 1 0.76875 1 0 1 0 1 1 1 1 0.51875 1 0 0 0 1 0 0 0 0.76250 1 0 1 1 0 0 0 0 0.51250 1 0 0 0 1 0 0 1 0.75625 1 0 1 1 0 0 0 1 0.50625 1 0 0 0 1 0 1 0 0.75000 1 0 1 1 0 0 1 0 0.50000 1 0 0 0 1 0 1 1 0.74375 1 1 1 1 1 1 1 0 OFF 1 0 0 0 1 1 0 0 0.73750 1 1 1 1 1 1 1 1 OFF 1 0 0 0 1 1 0 1 0.73125 1 0 0 0 1 1 1 0 0.72500 1 0 0 0 1 1 1 1 0.71875 20 FN9226.1 May 5, 2008 ISL6306 Load-Line Regulation Output-Voltage Offset Programming Some microprocessor manufacturers require a preciselycontrolled output resistance. This dependence of output voltage on load current is often termed “droop” or “load line” regulation. By adding a well controlled output impedance, the output voltage can effectively be level shifted in a direction which works to achieve the load-line regulation required by these manufacturers. The ISL6306 allows the designer to accurately adjust the offset voltage. When a resistor (ROFS) is connected between OFS to VCC, the voltage across it is regulated to 1.6V. This causes a proportional current (IOFS) to flow into OFS. If ROFS is connected to ground, the voltage across it is regulated to 0.4V, and IOFS flows out of OFS. A resistor between DAC and REF (RREF) is selected so that the product (IOFS x ROFS) is equal to the desired offset voltage. These functions are shown in Figure 9. In other cases, the designer may determine that a more cost-effective solution can be achieved by adding droop. Droop can help to reduce the output-voltage spike that results from fast load-current demand changes. The magnitude of the spike is dictated by the ESR and ESL of the output capacitors selected. By positioning the no-load voltage level near the upper specification limit, a larger negative spike can be sustained without crossing the lower limit. By adding a well controlled output impedance, the output voltage under load can effectively be level shifted down so that a larger positive spike can be sustained without crossing the upper specification limit. Once the desired output offset voltage has been determined, use Equations 11 and 12 to set ROFS: For Positive Offset (connect ROFS to VCC): 1.6 × R REF R OFS = -----------------------------V OFFSET (EQ. 11) For Negative Offset (connect ROFS to GND): 0.4 × R REF R OFS = -----------------------------V OFFSET (EQ. 12) As shown in Figure 8, a current proportional to the average current of all active channels (IAVG) flows from FB through a load-line regulation resistor RFB. The resulting voltage drop across RFB is proportional to the output current, effectively creating an output voltage droop with a steady-state value defined as Equation 8: V DROOP = I AVG R FB FB DYNAMIC VID D/A DAC RREF (EQ. 8) E/A REF The regulated output voltage is reduced by the droop voltage (VDROOP). The output voltage as a function of load current is derived by combining Equation 8 with the appropriate sample current expression defined by the current sense method employed. ⎛ I OUT R X ⎞ - ------------------ R FB⎟ V OUT = V REF – V OFS – ⎜ -----------⎝ N R ISEN ⎠ VCC OR GND (EQ. 9) - Where VREF is the reference voltage, VOFS is the programmed offset voltage, IOUT is the total output current of the converter, RISEN is the sense resistor connected to the ISEN+ pin, and RFB is the feedback resistor, N is the active channel number, and RX is the DCR, rDS(ON), or RSENSE depending on the sensing method. Therefore the equivalent loadline impedance, i.e. Droop impedance, is equal to Equation 10: R FB R X -----------------R LL = -----------N R ISEN (EQ. 10) 21 ROFS 1.6V + + 0.4V VCC - OFS ISL6306 GND FIGURE 9. OUTPUT VOLTAGE OFFSET PROGRAMMING Dynamic VID Modern microprocessors need to make changes to their core voltage as part of normal operation. They direct the core-voltage regulator to do this by making changes to the VID inputs during regulator operation. The power management solution is required to monitor the DAC inputs and respond to on-the-fly VID changes in a controlled manner. Supervising the safe output voltage transition within the DAC range of the processor without discontinuity or disruption is a necessary function of the core-voltage regulator. FN9226.1 May 5, 2008 ISL6306 The ISL6306 checks the VID inputs six times every switching cycle. If the VID code is found to have been changed, the controller waits for half of a switching cycle before executing a 6.25mV step change. If the difference between DAC level and the new VID code changes during the half-cycle waiting period, no change to the DAC output is made. If the VID code is more than 1 bit higher or lower than the DAC (not recommended), the controller will execute 6.26mV step change six times per cycle until VID and DAC are equal. Therefore it is important to carefully control the rate of VID stepping in 1-bit increments. In order to ensure the smooth transition of output voltage during VID change, a VID step change smoothing network, composed of RREF and CREF, can be used. The selection of RREF is based on the desired offset voltage as detailed in “OutputVoltage Offset Programming” on page 21. The selection of CREF is based on the time duration for 1 bit VID change and the allowable delay time. Assuming the microprocessor controls the VID change at 1-bit every TVID, the relationship between the time constant of RREF and CREF network and TVID is given by Equation 13. (EQ. 13) C REF R REF = T VID Operation Initialization Prior to converter initialization, proper conditions must exist on the enable inputs and VCC. When the conditions are met, the controller begins soft-start. Once the output voltage is within the proper window of operation, VR_RDY asserts logic high. ISL6306 INTERNAL CIRCUIT EXTERNAL CIRCUIT +12V VCC POR CIRCUIT ENABLE COMPARATOR + 10kΩ EN_PWR 910Ω 0.875V + EN_VTT - Enable and Disable While in shutdown mode, the PWM outputs are held in a high-impedance state to assure the drivers remain off. The following input conditions must be met before the ISL6306 is released from shutdown mode. 1. The bias voltage applied at VCC must reach the internal power-on reset (POR) rising threshold. Once this threshold is reached, proper operation of all aspects of the ISL6306 is guaranteed. Hysteresis between the rising and falling thresholds assure that once enabled, the ISL6306 will not inadvertently turn off unless the bias voltage drops substantially (see “Electrical Specifications” on page 8). 2. The ISL6306 features an enable input (EN_PWR) for power sequencing between the controller bias voltage and another voltage rail. The enable comparator holds the ISL6306 in shutdown until the voltage at EN_PWR rises above 0.875V. The enable comparator has about 130mV of hysteresis to prevent bounce. It is important that the driver ICs reach their POR level before the ISL6306 becomes enabled. The schematic in Figure 10 demonstrates sequencing the ISL6306 with the ISL66xx family of Intersil MOSFET drivers, which require 12V bias. 3. The voltage on EN_VTT must be higher than 0.875V to enable the controller. This pin is typically connected to the output of VTT VR. When all conditions above are satisfied, ISL6306 begins the soft-start and ramps the output voltage to 1.1V first. After remaining at 1.1V for some time, ISL6306 reads the VID code at VID input pins. If the VID code is valid, ISL6306 will regulate the output to the final VID setting. If the VID code is OFF code, ISL6306 will shut down, and cycling VCC, EN_PWR or EN_VTT is needed to restart. Soft-Start ISL6306 based VR has 4 periods during soft-start as shown in Figure 11. After VCC, EN_VTT and EN_PWR reach their POR/enable thresholds, The controller will have fixed delay period TD1. After this delay period, the VR will begin first soft-start ramp until the output voltage reaches 1.1V VBOOT voltage. Then, the controller will regulate the VR voltage at 1.1V for another fixed period TD3. At the end of TD3 period, ISL6306 reads the VID signals. If the VID code is valid, ISL6306 will initiate the second soft-start ramp until the voltage reaches the VID voltage minus offset voltage. 0.875V The soft-start time is the sum of the 4 periods as shown in Equation 14. SOFT-START AND FAULT LOGIC T SS = TD1 + TD2 + TD3 + TD4 FIGURE 10. POWER SEQUENCING USING THRESHOLDSENSITIVE ENABLE (EN) FUNCTION 22 (EQ. 14) TD1 is a fixed delay with the typical value as 1.36ms. TD3 is determined by the fixed 85µs plus the time to obtain valid VID voltage. If the VID is valid before the output reaches the 1.1V, the minimum time to validate the VID input is 500ns. Therefore the minimum TD3 is about 86µs. FN9226.1 May 5, 2008 ISL6306 During TD2 and TD4, ISL6306 digitally controls the DAC voltage change at 6.25mV per step. The time for each step is determined by the frequency of the soft-start oscillator which is defined by the resistor Rss from SS pin to GND. The second soft-start ramp time TD2 and TD4 can be calculated based on Equations 15 and 16: Undervoltage Detection 1.1xR SS TD2 = ------------------------ ( μs ) 6.25x25 (EQ. 15) ( V VID – 1.1 )xR SS TD4 = ------------------------------------------------ ( μs ) 6.25x25 (EQ. 16) Regardless of the VR being enabled or not, the ISL6306 overvoltage protection (OVP) circuit will be active after its POR. The OVP thresholds are different under different operation conditions. When VR is not enabled and before the second soft-start, the OVP threshold is 1.275V. Once the controller detects valid VID input, the OVP trip point will be changed to VID plus 175mV. For example, when VID is set to 1.5V and the Rss is set at 100kΩ, the first soft-start ramp time TD2 will be 704µs and the second soft-start ramp time TD4 will be 256µs. After the DAC voltage reaches the final VID setting, VR_RDY will be set to high with the fixed delay TD5. The typical value for TD5 is 85µs. VOUT, 500mV/DIV TD1 TD2 TD3 TD4 TD5 EN_VTT VR_REDY 500µs/DIV FIGURE 11. SOFT-START WAVEFORMS The undervoltage threshold is set at 50% of the VID code. When the output voltage at VSEN is below the undervoltage threshold, VR_RDY is pulled low. Overvoltage Protection Two actions are taken by the ISL6306 to protect the microprocessor load when an overvoltage condition occurs. At the inception of an overvoltage event, all PWM outputs are commanded low instantly (less than 20ns) until the voltage at VDIFF falls below 0.4V. This causes the Intersil drivers to turn on the lower MOSFETs and pull the output voltage below a level that might cause damage to the load. The PWM outputs remain low until VDIFF falls below 0.4V, and then PWM signals enter a high-impedance state. The Intersil drivers respond to the high-impedance input by turning off both upper and lower MOSFETs. If the overvoltage condition reoccurs, the ISL6306 will again command the lower MOSFETs to turn on. The ISL6306 will continue to protect the load in this fashion as long as the overvoltage condition occurs. Once an overvoltage condition is detected, normal PWM operation ceases until the ISL6306 is reset. Cycling the voltage on EN_PWR, EN_VTT or VCC below the PORfalling threshold will reset the controller. Cycling the VID codes will not reset the controller. Fault Monitoring and Protection VR_RDY The ISL6306 actively monitors output voltage and current to detect fault conditions. Fault monitors trigger protective measures to prevent damage to a microprocessor load. One common power good indicator is provided for linking to external system monitors. The schematic in Figure 12 outlines the interaction between the fault monitors and the VR_RDY signal. DELAY 50% DAC VR_RDY Signal The VR_RDY pin is an open-drain logic output to indicate that the soft-start period is completed and the output voltage is within the regulated range. VR_RDY is pulled low during shutdown and releases high after a successful soft-start and a fixed delay TD5. VR_RDY will be pulled low when an undervoltage or overvoltage condition is detected, or the controller is disabled by a reset from EN_PWR, EN_VTT, POR, or VID OFF-code. OC - + UV SOFT-START, FAULT AND CONTROL LOGIC - 100µA + I1 REPEAT FOR EACH CHANNEL - 100µA OC + IAVG + VDIFF OV VID + 0.175V FIGURE 12. VR_RDY AND PROTECTION CIRCUITRY 23 FN9226.1 May 5, 2008 ISL6306 Overcurrent Protection Thermal Monitoring (VR_HOT/VR_FAN) ISL6306 has two levels of overcurrent protection. Each phase is protected from a sustained overcurrent condition on a delayed basis, while the combined phase currents are protected on an instantaneous basis. There are two thermal signals to indicate the temperature status of the voltage regulator: VR_HOT and VR_FAN. Both VR_FAN and VR_HOT are open-drain outputs, and external pull-up resistors are required. In instantaneous protection mode, the ISL6306 utilizes the sensed average current IAVG to detect an overcurrent condition. See “Channel-Current Balance” on page 15 for more detail on how the average current is measured. The average current is continually compared with a constant 100μA reference current as shown in Figure 12. Once the average current exceeds the reference current, a comparator triggers the converter to shutdown. VR_FAN signal indicates that the temperature of the voltage regulator is high and more cooling airflow is needed. VR_HOT signal can be used to inform the system that the temperature of the voltage regulator is too high and the CPU should reduce its power consumption. VR_HOT signal may be tied to the CPU’s PROC_HOT signal. In individual overcurrent protection mode, the ISL6306 continuously compares the current of each channel with the same 100μA reference current. If any channel current exceeds the reference current continuously for eight consecutive cycles, the comparator triggers the converter to shutdown. The diagram of thermal monitoring function block is shown in Figure 14. One NTC resistor should be placed close to the power stage of the voltage regulator to sense the operational temperature, and one pull-up resistor is needed to form the voltage divider for TM pin. As the temperature of the power stage increases, the resistance of the NTC will reduce, resulting in the reduced voltage at TM pin. Figure 15 shows the TM voltage over the temperature for a typical design with a recommended 6.8kΩ NTC (P/N: NTHS0805N02N6801 from Vishay) and 1kΩ resistor RTM1. We recommend using those resistors for the accurate temperature compensation. OUTPUT CURRENT 0A OUTPUT VOLTAGE 0V There are two comparators with hysteresis to compare the TM pin voltage to the fixed thresholds for VR_FAN and VR_HOT signals respectively. VR_FAN signal is set to high when TM voltage is lower than 33% of VCC voltage, and is pulled to GND when TM voltage increases to above 39% of VCC voltage. VR_FAN is set to high when TM voltage goes below 28% of VCC voltage, and is pulled to GND when TM voltage goes back to above 33% of VCC voltage. Figure 16 shows the operation of those signals. 2ms/DIV FIGURE 13. OVERCURRENT BEHAVIOR IN HICCUP MODE. FSW = 500kHz At the beginning of overcurrent shutdown, the controller places all PWM signals in a high-impedance state within 20ns commanding the Intersil MOSFET driver ICs to turn off both upper and lower MOSFETs. The system remains in this state a period of 4096 switching cycles. If the controller is still enabled at the end of this wait period, it will attempt a softstart. If the fault remains, the trip-retry cycles will continue indefinitely (as shown in Figure 13) until either controller is disabled or the fault is cleared. Note that the energy delivered during trip-retry cycling is much less than during full-load operation, so there is no thermal hazard during this kind of operation. 24 VCC VR_FAN R TM1 0.33VCC VR_HOT TM oc R NTC 0.28VCC FIGURE 14. BLOCK DIAGRAM OF THERMAL MONITORING FUNCTION FN9226.1 May 5, 2008 ISL6306 Temperature Compensation VTM/VCC vs TEMPERATURE ISL6306 supports inductor DCR sensing, MOSFET rDS(ON) sensing, or resistive sensing techniques. Both inductor DCR and MOSFET rDS(ON) have the positive temperature coefficient, which is about +0.38%/°C. Because the voltage across inductor or MOSFET is sensed for the output current information, the sensed current has the same positive temperature coefficient as the inductor DCR or MOSFET rDS(ON). 100 90 VTM/VCC (%) 80 70 60 50 40 30 20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) In order to obtain the correct current information, there should be a way to correct the temperature impact on the current sense component. ISL6306 provides two methods: integrated temperature compensation and external temperature compensation. Integrated Temperature Compensation FIGURE 15. THE RATIO OF TM VOLTAGE TO NTC TEMPERATURE WITH RECOMMENDED PARTS When TCOMP voltage is equal or greater than VCC/15, ISL6306 will utilize the voltage at TM and TCOMP pins to compensate the temperature impact on the sensed current. The block diagram of this function is shown in Figure 17. TM 0.39*VCC 0.33*VCC 0.28*VCC V CC Isen4 CHANNEL R TM1 VR_FAN TM VR_HOT TEMPERATURE (°C) T1 T2 Based on the NTC temperature characteristics and the desired threshold of VR_HOT signal, the pull-up resistor RTM1 of TM pin is given by: (EQ. 17) RNTC(T3) is the NTC resistance at the VR_HOT threshold temperature T3. The NTC resistance at the set point T2 and release point T1 of VR_FAN signal can be calculated as: R NTC ( T2 ) = 1.267xR NTC ( T3 ) (EQ. 18) R NTC ( T1 ) = 1.644xR NTC ( T3 ) (EQ. 19) With the NTC resistance value obtained from Equations 18 and 19, the temperature value T2 and T1 can be found from the NTC datasheet. 25 SENSE Non-linear NON-LINEAR A/D A/D Isen1 I4 I3 I2 I1 R NTC T3 FIGURE 16. VR_HOT AND VR_FAN SIGNAL vs TM VOLTAGE R TM1 = 2.75xR NTC ( T3 ) oc Isen3 Isen2 Channel current CURRENT sense D/A V CC ki R TC1 TCOMP 4-bit 4-BIT A/D A/D DROOP AND OVERCURRENT Droop & PROTECTION Over current protection R TC2 FIGURE 17. BLOCK DIAGRAM OF INTEGRATED TEMPERATURE COMPENSATION When the TM NTC is placed close to the current sense component (inductor or MOSFET), the temperature of the NTC will track the temperature of the current sense component. Therefore the TM voltage can be utilized to obtain the temperature of the current sense component. Based on VCC voltage, ISL6306 converts the TM pin voltage to a 6-bit TM digital signal for temperature compensation. With the non-linear A/D converter of ISL6306, TM digital signal is linearly proportional to the NTC temperature. For accurate temperature compensation, the ratio of the TM voltage to the NTC temperature of the practical design should be similar to that in Figure 15. FN9226.1 May 5, 2008 ISL6306 Depending on the location of the NTC and the airflow, the NTC may be cooler or hotter than the current sense component. TCOMP pin voltage can be utilized to correct the temperature difference between NTC and the current sense component. When a different NTC type or different voltage divider is used for the TM function, TCOMP voltage can also be used to compensate for the difference between the recommended TM voltage curve in Figure 16 and that of the actual design. According to the VCC voltage, ISL6306 converts the TCOMP pin voltage to a 4-bit TCOMP digital signal as TCOMP factor N. TCOMP factor N is an integer between 0 and 15. The integrated temperature compensation function is disabled for N = 0. For N = 4, the NTC temperature is equal to the temperature of the current sense component. For N < 4, the NTC is hotter than the current sense component. The NTC is cooler than the current sense component for N > 4. When N > 4, the larger TCOMP factor N, the larger the difference between the NTC temperature and the temperature of the current sense component. ISL6306 multiplexes the TCOMP factor N with the TM digital signal to obtain the adjustment gain to compensate the temperature impact on the sensed channel current. The compensated channel current signal is used for droop and overcurrent protection functions. 9. Run the actual board under full load again with the proper resistors connected to the TCOMP pin. 10. Record the output voltage as V1 immediately after the output voltage is stable with the full load. Record the output voltage as V2 after the VR reaches the thermal steady state. 11. If the output voltage increases over 2mV as the temperature increases, i.e. V2 - V1 > 2mV, reduce N and redesign RTC2; if the output voltage decreases over 2mV as the temperature increases, i.e. V1 - V2 > 2mV, increase N and redesign RTC2. The design spreadsheet is available for those calculations. External Temperature Compensation By setting the voltage of TCOMP pin to 0, the integrated temperature compensation function is disabled. And one external temperature compensation network, shown in Figure 18, can be used to cancel the temperature impact on the droop (i.e. load line). COMP FB IDROOP Design Procedure 1. Properly choose the voltage divider for TM pin to match the TM voltage VS temperature curve with the recommended curve in Figure 15. 2. Run the actual board under the full load and the desired cooling condition. 3. After the board reaches the thermal steady state, record the temperature (TCSC) of the current sense component (inductor or MOSFET) and the voltage at TM and VCC pins. 4. Use Equation 20 to calculate the resistance of the TM NTC, and find out the corresponding NTC temperature TNTC from the NTC datasheet. R NTC ( T V TM xR TM1 = ------------------------------) V CC – V NTC TM (EQ. 20) 5. Use Equation 21 to calculate the TCOMP factor N: 209x ( T CSC – T ) NTC N = -------------------------------------------------------- + 4 3xT NTC + 400 (EQ. 21) 6. Choose an integral number close to the above result for the TCOMP factor. If this factor is higher than 15, use N = 15. If it is less than 1, use N = 1. 7. Choose the pull-up resistor RTC1 (typical 10kΩ). 8. If N = 15, do not need the pull-down resistor RTC2, otherwise obtain RTC2 by Equation 22: NxR TC1 R TC2 = ----------------------15 – N (EQ. 22) 26 oc VDIFF FIGURE 18. VOLTAGE AT IDROOP PIN WITH A RESISTOR PLACED FROM IDROOP PIN TO GND WHEN LOAD CURRENT CHANGES The sensed current will flow out of IDROOP pin and develop the droop voltage across the resistor equivalent (RFB) between FB and VDIFF pins. If RFB resistance reduces as the temperature increases, the temperature impact on the droop can be compensated. An NTC resistor can be placed close to the power stage and used to form RFB. Due to the non-linear temperature characteristics of the NTC, a resistor network is needed to make the equivalent resistance between FB and VDIFF pin is reverse proportional to the temperature. The external temperature compensation network can only compensate the temperature impact on the droop, while it has no impact to the sensed current inside ISL6306. Therefore this network cannot compensate for the temperature impact on the overcurrent protection function. Current Sense Output The current from IDROOP pin is the sensed average current inside ISL6306. In typical application, IDROOP pin is connected to FB pin for the application where load line is FN9226.1 May 5, 2008 ISL6306 required. When load line function is not needed, IDROOP pin can used to obtain the load current information: with one resistor from IDROOP pin to GND, the voltage at IDROOP pin will be proportional to the load current. The resistor from IDROOP to GND should be chosen to ensure that the voltage at IDROOP pin is less than 2V under the maximum load current. General Design Guide This design guide is intended to provide a high-level explanation of the steps necessary to create a multiphase power converter. It is assumed that the reader is familiar with many of the basic skills and techniques referenced below. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts for all common microprocessor applications. Power Stages The first step in designing a multiphase converter is to determine the number of phases. This determination depends heavily on the cost analysis which in turn depends on system constraints that differ from one design to the next. Principally, the designer will be concerned with whether components can be mounted on both sides of the circuit board; whether through-hole components are permitted; and the total board space available for power-supply circuitry. Generally speaking, the most economical solutions are those in which each phase handles between 15A and 20A. All surface-mount designs will tend toward the lower end of this current range. If through-hole MOSFETs and inductors can be used, higher per-phase currents are possible. In cases where board space is the limiting constraint, current can be pushed as high as 40A per phase, but these designs require heat sinks and forced air to cool the MOSFETs, inductors and heat-dissipating surfaces. MOSFETs The choice of MOSFETs depends on the current each MOSFET will be required to conduct; the switching frequency; the capability of the MOSFETs to dissipate heat; and the availability and nature of heat sinking and air flow. dead time when inductor current is flowing through the lower-MOSFET body diode. This term is dependent on the diode forward voltage at IM, VD(ON); the switching frequency, fS; and the length of dead times, td1 and td2, at the beginning and the end of the lower-MOSFET conduction interval respectively. ⎛I ⎞ IM I M I P-P P-P-⎞ t P LOW, 2 = V D ( ON ) f S ⎛ ----d1 + ⎜ ------ – -----------⎟ t d2 ⎝ N- + ---------2 ⎠ 2 ⎠ ⎝N (EQ. 24) Thus the total maximum power dissipated in each lower MOSFET is approximated by the summation of PLOW,1 and PLOW,2. UPPER MOSFET POWER CALCULATION In addition to rDS(ON) losses, a large portion of the upperMOSFET losses are due to currents conducted across the input voltage (VIN) during switching. Since a substantially higher portion of the upper-MOSFET losses are dependent on switching frequency, the power calculation is more complex. Upper MOSFET losses can be divided into separate components involving the upper-MOSFET switching times; the lower-MOSFET body-diode reverserecovery charge (Qrr) and the upper MOSFET rDS(ON) conduction loss. When the upper MOSFET turns off, the lower MOSFET does not conduct any portion of the inductor current until the voltage at the phase node falls below ground. Once the lower MOSFET begins conducting, the current in the upper MOSFET falls to zero as the current in the lower MOSFET ramps up to assume the full inductor current. In Equation 25, the required time for this commutation is t1 and the approximated associated power loss is PUP,1. I M I P-P⎞ ⎛ t 1 ⎞ P UP,1 ≈ V IN ⎛ ----- ⎜ ---- ⎟ f ⎝ N- + ---------2 ⎠ ⎝ 2⎠ S (EQ. 25) At turn on, the upper MOSFET begins to conduct and this transition occurs over a time t2. In Equation 26, the approximate power loss is PUP,2. ⎛ I M I P-P⎞ ⎛ t 2 ⎞ P UP, 2 ≈ V IN ⎜ ----- – -----------⎟ ⎜ ---- ⎟ f S 2 ⎠⎝ 2⎠ ⎝N (EQ. 26) LOWER MOSFET POWER CALCULATION The calculation for heat dissipated in the lower MOSFET is simple, since virtually all of the heat loss in the lower MOSFET is due to current conducted through the channel resistance (rDS(ON)). In Equation 23, IM is the maximum continuous output current; IPP is the peak-to-peak inductor current (see Equation 1); d is the duty cycle (VOUT/VIN); and L is the per-channel inductance. P LOW, 1 = r DS ( ON ) I L, 2P-P ( 1 – d ) ⎛ I M⎞ 2 ⎜ ⎟ ( 1 – d ) + --------------------------------------⎝ N⎠ (EQ. 23) 12 An additional term can be added to the lower-MOSFET loss equation to account for additional loss accrued during the 27 A third component involves the lower MOSFET’s reverserecovery charge (Qrr). Since the inductor current has fully commutated to the upper MOSFET before the lowerMOSFET’s body diode can draw all of Qrr, it is conducted through the upper MOSFET across VIN. The power dissipated as a result is PUP,3 and is approximately P UP,3 = V IN Q rr f S (EQ. 27) Finally, the resistive part of the upper MOSFET’s is given in Equation 28 as PUP,4. The total power dissipated by the upper MOSFET at full load can now be approximated as the summation of the results FN9226.1 May 5, 2008 ISL6306 from Equations 25, 26, and 27. Since the power equations depend on MOSFET parameters, choosing the correct MOSFETs can be an iterative process involving repetitive solutions to the loss equations for different MOSFETs and different switching frequencies. 2 2 I P-P ⎛ I M⎞ P UP,4 ≈ r DS ( ON ) ⎜ -----⎟ d + ----------- d 12 ⎝ N⎠ (EQ. 28) Current Sensing Resistor The resistors connected between these pins and the respective phase nodes determine the gains in the load-line regulation loop and the channel-current balance loop as well as setting the overcurrent trip point. Select values for these resistors based on the room temperature rDS(ON) of the lower MOSFETs, DCR of inductor or additional resistor; the full-load operating current, IFL; and the number of phases, N using Equation 29. I FL -------N (EQ. 29) In certain circumstances, it may be necessary to adjust the value of one or more ISEN resistor. When the components of one or more channels are inhibited from effectively dissipating their heat so that the affected channels run hotter than desired, choose new, smaller values of RISEN for the affected phases (see the section entitled “Channel-Current Balance” on page 15). Choose RISEN2 in proportion to the desired decrease in temperature rise in order to cause proportionally less current to flow in the hotter phase. ΔT R ISEN ,2 = R ISEN ----------2 ΔT 1 ∑ RISEN ( n ) (EQ. 32) n Compensation The two opposing goals of compensating the voltage regulator are stability and speed. Depending on whether the regulator employs the optional load-line regulation as described in Load-Line Regulation, there are two distinct methods for achieving these goals. COMPENSATING LOAD-LINE REGULATED CONVERTER The load-line regulated converter behaves in a similar manner to a peak-current mode controller because the two poles at the output-filter LC resonant frequency split with the introduction of current information into the control loop. The final location of these poles is determined by the system function, the gain of the current signal, and the value of the compensation components, RC and CC. Since the system poles and zero are affected by the values of the components that are meant to compensate them, the solution to the system equation becomes fairly complicated. Fortunately there is a simple approximation that comes very close to an optimal solution. Treating the system as though it were a voltage-mode regulator by compensating the LC poles and the ESR zero of the voltage-mode approximation yields a solution that is always stable with very close to ideal transient performance. C2 (OPTIONAL) (EQ. 30) RC In Equation 30, make sure that ΔT2 is the desired temperature rise above the ambient temperature, and ΔT1 is the measured temperature rise above the ambient temperature. While a single adjustment according to Equation 30 is usually sufficient, it may occasionally be necessary to adjust RISEN two or more times to achieve optimal thermal balance between all channels. CC COMP FB + RFB VDROOP IDROOP ISL6306 RX R ISEN = ---------------------70 ×10 – 6 V DROOP R FB = -------------------------------I FL r DS ( ON ) VDIFF Load-Line Regulation Resistor The load-line regulation resistor is labelled RFB in Figure 8. Its value depends on the desired full load droop voltage (VDROOP in Figure 8). If Equation 29 is used to select each ISEN resistor, the load-line regulation resistor is as shown in Equation 31. V DROOP R FB = -----------------------–6 70 ×10 (EQ. 31) If one or more of the ISEN resistors is adjusted for thermal balance, as in Equation 30, the load-line regulation resistor should be selected according to Equation 32 where IFL is the full-load operating current and RISEN(n) is the ISEN resistor connected to the nth ISEN pin. 28 FIGURE 19. COMPENSATION CONFIGURATION FOR LOAD-LINE REGULATED ISL6306 CIRCUIT The feedback resistor, RFB, has already been chosen as outlined in “Load-Line Regulation Resistor” on page 28. Select a target bandwidth for the compensated system, f0. The target bandwidth must be large enough to assure adequate transient performance, but smaller than 1/3 of the per-channel switching frequency. The values of the compensation components depend on the relationships of f0 to the LC pole frequency and the ESR zero frequency. For each of the three cases which follow, there is a separate set of equations for the compensation components. FN9226.1 May 5, 2008 ISL6306 1 ------------------- > f 0 2π LC C2 2πf 0 V P-P LC R C = R FB -------------------------------------0.75V RC CC IN 0.75V IN C C = ------------------------------------2πV P-P R FB f 0 COMP FB C1 Case 2: 1 1 ------------------- ≤ f 0 < ----------------------------2πC ( ESR ) 2π LC V P-P ( 2π ) 2 f 02 LC R C = R FB --------------------------------------------0.75 V RFB R1 IDROOP ISL6306 Case 1: VDIFF (EQ. 33) IN 0.75V IN C C = -------------------------------------------------------------2 ( 2π ) f 02 V P-P R FB LC Case 3: 1 f 0 > -----------------------------2πC ( ESR ) 2π f 0 V P-P L R C = R FB ----------------------------------------0.75 V IN ( ESR ) 0.75V IN ( ESR ) C C C = -----------------------------------------------2πV P-P R FB f 0 L In Equation 33, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VPP is the peak-topeak sawtooth signal amplitude as described in Figure 7 and “Electrical Specifications” on page 8. The optional capacitor C2, is sometimes needed to bypass noise away from the PWM comparator (see Figure 20). Keep a position available for C2, and be prepared to install a highfrequency capacitor of between 22pF and 150pF in case any leading-edge jitter problem is noted. Once selected, the compensation values in Equation 33 assure a stable converter with reasonable transient performance. In most cases, transient performance can be improved by making adjustments to RC. Slowly increase the value of RC while observing the transient performance on an oscilloscope until no further improvement is noted. Normally, CC will not need adjustment. Keep the value of CC from Equation 33 unless some performance issue is noted. COMPENSATION WITHOUT LOAD-LINE REGULATION The non load-line regulated converter is accurately modeled as a voltage-mode regulator with two poles at the LC resonant frequency and a zero at the ESR frequency. A type III controller, as shown in Figure 20, provides the necessary compensation. 29 FIGURE 20. COMPENSATION CIRCUIT FOR ISL6306 BASED CONVERTER WITHOUT LOAD-LINE REGULATION The first step is to choose the desired bandwidth, f0, of the compensated system. Choose a frequency high enough to assure adequate transient performance but not higher than 1/3 of the switching frequency. The type-III compensator has an extra high-frequency pole, fHF. This pole can be used for added noise rejection or to assure adequate attenuation at the error-amplifier high-order pole and zero frequencies. A good general rule is to choose fHF = 10f0, but it can be higher if desired. Choosing fHF to be lower than 10f0 can cause problems with too much phase shift below the system bandwidth. In the solutions to the compensation equations, there is a single degree of freedom. For the solutions presented in Equation 34, RFB is selected arbitrarily. The remaining compensation components are then selected according to Equation 34. C ( ESR ) R 1 = R FB ----------------------------------------LC – C ( ESR ) LC – C ( ESR ) C 1 = ----------------------------------------R FB 0.75V IN C 2 = -------------------------------------------------------------------( 2π ) 2 f 0 f HF LCR FB V P-P 2 V P-P ⎛ 2π⎞ f 0 f HF LCR FB ⎝ ⎠ R C = -------------------------------------------------------------------⎛2πf ⎞ 0.75 V ⎝ HF LC – 1⎠ IN ⎞ 0.75V IN ⎛2πf ⎝ HF LC – 1⎠ C C = --------------------------------------------------------------------( 2π ) 2 f 0 f HF LCR FB V P-P (EQ. 34) In Equation 34, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VP-P is the peak-topeak sawtooth signal amplitude as described in Figure 7 and “Electrical Specifications” on page 8. FN9226.1 May 5, 2008 ISL6306 Output Filter Design The output inductors and the output capacitor bank together to form a low-pass filter responsible for smoothing the pulsating voltage at the phase nodes. The output filter also must provide the transient energy until the regulator can respond. Because it has a low bandwidth compared to the switching frequency, the output filter necessarily limits the system transient response. The output capacitor must supply or sink load current while the current in the output inductors increases or decreases to meet the demand. In high-speed converters, the output capacitor bank is usually the most costly (and often the largest) part of the circuit. Output filter design begins with minimizing the cost of this part of the circuit. The critical load parameters in choosing the output capacitors are the maximum size of the load step, ΔI; the load-current slew rate, di/dt; and the maximum allowable output-voltage deviation under transient loading, ΔVMAX. Capacitors are characterized according to their capacitance (ESR) and ESL (equivalent series inductance). At the beginning of the load transient, the output capacitors supply all of the transient current. The output voltage will initially deviate by an amount approximated by the voltage drop across the ESL. As the load current increases, the voltage drop across the ESR increases linearly until the load current reaches its final value. The capacitors selected must have sufficiently low ESL and ESR so that the total outputvoltage deviation is less than the allowable maximum. Neglecting the contribution of inductor current and regulator response, the output voltage initially deviates by an amount: di ΔV ≈ ( ESL ) ----- + ( ESR ) ΔI dt (EQ. 35) The filter capacitor must have sufficiently low ESL and ESR so that ΔV < ΔVMAX. Most capacitor solutions rely on a mixture of high-frequency capacitors with relatively low capacitance in combination with bulk capacitors having high capacitance but limited high-frequency performance. Minimizing the ESL of the high-frequency capacitors allows them to support the output voltage as the current increases. Minimizing the ESR of the bulk capacitors allows them to supply the increased current with less output voltage deviation. The ESR of the bulk capacitors also creates the majority of the output-voltage ripple. As the bulk capacitors sink and source the inductor AC ripple current (see “Interleaving” on page 12 and Equation 2), a voltage develops across the bulk-capacitor ESR equal to IC,P-P (ESR). Thus, once the output capacitors are selected, the maximum allowable ripple voltage, VP-P(MAX), determines the lower limit on the inductance. ⎛V – N V ⎞ OUT⎠ V OUT ⎝ IN L ≥ ( ESR ) -----------------------------------------------------------f S V IN V PP( MAX ) (EQ. 36) transient, the capacitor voltage becomes slightly depleted. The output inductors must be capable of assuming the entire load current before the output voltage decreases more than ΔVMAX. This places an upper limit on inductance. Equation 37 gives the upper limit on L for the cases when the trailing edge of the current transient causes a greater output-voltage deviation than the leading edge. Equation 38 addresses the leading edge. Normally, the trailing edge dictates the selection of L because duty cycles are usually less than 50%. Nevertheless, both inequalities should be evaluated, and L should be selected based on the lower of the two results. In each equation, L is the per-channel inductance, C is the total output capacitance, and N is the number of active channels. 2NCVO - ΔV MAX – ΔI ( ESR ) L ≤ -------------------( ΔI ) 2 ( 1.25 ) NC L ≤ -------------------------- ΔV MAX – ΔI ( ESR ) ⎛ V IN – V O⎞ ⎝ ⎠ ( ΔI ) 2 (EQ. 37) (EQ. 38) Switching Frequency There are a number of variables to consider when choosing the switching frequency, as there are considerable effects on the upper-MOSFET loss calculation. These effects are outlined in “MOSFETs” on page 27, and they establish the upper limit for the switching frequency. The lower limit is established by the requirement for fast transient response and small output-voltage ripple as outlined in “Output Filter Design” on page 30. Choose the lowest switching frequency that allows the regulator to meet the transient-response requirements. Switching frequency is determined by the selection of the frequency-setting resistor, RT (see the figures labelled Typical Applications on pages 4, 5, 6, and 7). Equation 39 is provided to assist in selecting the correct value for RT. 10 2.5X10 R T = -------------------------FS (EQ. 39) Input Capacitor Selection The input capacitors are responsible for sourcing the AC component of the input current flowing into the upper MOSFETs. Their RMS current capacity must be sufficient to handle the AC component of the current drawn by the upper MOSFETs which is related to duty cycle and the number of active phases. Since the capacitors are supplying a decreasing portion of the load current while the regulator recovers from the . 30 FN9226.1 May 5, 2008 ISL6306 For a two phase design, use Figure 21 to determine the input-capacitor RMS current requirement given the duty cycle, maximum sustained output current (IO), and the ratio of the per-phase peak-to-peak inductor current (IL,P-P) to IO. Select a bulk capacitor with a ripple current rating which will minimize the total number of input capacitors required to support the RMS current calculated. The voltage rating of the capacitors should also be at least 1.25 times greater than the maximum input voltage. . INPUT-CAPACITOR CURRENT (IRMS/IO) 0.3 0.2 0.1 Figures 22 and 23 provide the same input RMS current information for three and four phase designs respectively. Use the same approach to selecting the bulk capacitor type and number as described above. IL,P-P = 0 IL,P-P = 0.5 IO IL,P-P = 0.75 IO 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO/VIN) FIGURE 21. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR 2-PHASE CONVERTER INPUT-CAPACITOR CURRENT (IRMS/IO) 0.3 IL,P-P = 0 IL,P-P = 0.5 IO IL,P-P = 0.25 IO IL,P-P = 0.75 IO MULTIPHASE RMS IMPROVEMENT 0.2 0.1 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO/VIN) FIGURE 22. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR 3-PHASE CONVERTER Figure 23 is provided as a reference to demonstrate the dramatic reductions in input-capacitor RMS current upon the implementation of the multiphase topology. For example, compare the input RMS current requirements of a two-phase converter versus that of a single phase. Assume both converters have a duty cycle of 0.25, maximum sustained output current of 40A, and a ratio of IL,P-P to IO of 0.5. The single phase converter would require 17.3ARMS current capacity while the two-phase converter would only require 10.9ARMS. The advantages become even more pronounced when output current is increased and additional phases are added to keep the component cost down relative to the single phase approach. Layout Considerations The following layout strategies are intended to minimize the impact of board parasitic impedances on converter performance and to optimize the heat-dissipating capabilities of the printed-circuit board. These sections highlight some important practices which should not be overlooked during the layout process. 0.6 INPUT-CAPACITOR CURRENT (IRMS/IO) Low capacitance, high-frequency ceramic capacitors are needed in addition to the bulk capacitors to suppress leading and falling edge voltage spikes. The result from the high current slew rates produced by the upper MOSFETs turn on and off. Select low ESL ceramic capacitors and place one as close as possible to each upper MOSFET drain to minimize board parasitic impedances and maximize suppression. 0.4 Component Placement 0.2 IL,P-P = 0 IL,P-P = 0.5 IO IL,P-P = 0.75 IO 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO/VIN) FIGURE 23. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR SINGLE-PHASE CONVERTER 31 Within the allotted implementation area, orient the switching components first. The switching components are the most critical because they carry large amounts of energy and tend to generate high levels of noise. Switching component placement should take into account power dissipation. Align the output inductors and MOSFETs such that space between the components is minimized while creating the PHASE plane. Place the Intersil MOSFET driver IC as close as possible to the MOSFETs they control to reduce the parasitic impedances due to trace length between critical driver input FN9226.1 May 5, 2008 ISL6306 and output signals. If possible, duplicate the same placement of these components for each phase. Next, place the input and output capacitors. Position one high-frequency ceramic input capacitor next to each upper MOSFET drain. Place the bulk input capacitors as close to the upper MOSFET drains as dictated by the component size and dimensions. Long distances between input capacitors and MOSFET drains result in too much trace inductance and a reduction in capacitor performance. Locate the output capacitors between the inductors and the load, while keeping them in close proximity to the microprocessor socket. The ISL6306 can be placed off to one side or centered relative to the individual phase switching components. Routing of sense lines and PWM signals will guide final placement. Critical small signal components to place close to the controller include the ISEN resistors, RT resistor, feedback resistor, and compensation components. Bypass capacitors for the ISL6306 and ISL66XX driver bias supplies must be placed next to their respective pins. Trace parasitic impedances will reduce their effectiveness. Plane Allocation and Routing Dedicate one solid layer, usually a middle layer, for a ground plane. Make all critical component ground connections with vias to this plane. Dedicate one additional layer for power planes; breaking the plane up into smaller islands of common voltage. Use the remaining layers for signal wiring. Route phase planes of copper filled polygons on the top and bottom once the switching component placement is set. Size the trace width between the driver gate pins and the MOSFET gates to carry 4A of current. When routing components in the switching path, use short wide traces to reduce the associated parasitic impedances. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 32 FN9226.1 May 5, 2008 ISL6306 Package Outline Drawing L40.6x6 40 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 3, 10/06 4X 4.5 6.00 36X 0.50 A B 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 40 31 30 1 6.00 4 . 10 ± 0 . 15 21 10 0.15 (4X) 11 20 0.10 M C A B TOP VIEW 40X 0 . 4 ± 0 . 1 4 0 . 23 +0 . 07 / -0 . 05 BOTTOM VIEW SEE DETAIL "X" 0.10 C 0 . 90 ± 0 . 1 ( C BASE PLANE ( 5 . 8 TYP ) SEATING PLANE 0.08 C SIDE VIEW 4 . 10 ) ( 36X 0 . 5 ) C 0 . 2 REF 5 ( 40X 0 . 23 ) 0 . 00 MIN. 0 . 05 MAX. ( 40X 0 . 6 ) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 33 FN9226.1 May 5, 2008