INTERSIL ISL6336BCRZ

ISL6336B
®
Data Sheet
August 31, 2010
6-Phase PWM Controller with Light Load
Efficiency Enhancement and Current
Monitoring
The ISL6336B controls microprocessor core voltage
regulation by driving up to 6 interleaved synchronous-rectified
buck channels in parallel. Multiphase buck converter
architecture uses interleaved timing to multiply channel ripple
frequency and reduce input and output ripple currents. Lower
ripple results in fewer components, lower component cost,
reduced power dissipation, and smaller implementation area.
Microprocessor loads can generate load transients with
extremely fast edge rates and require high efficiency over
the full load range. The ISL6336B utilizes Intersil’s
proprietary Active Pulse Positioning (APP) and Adaptive
Phase Alignment (APA) modulation scheme and a
proprietary active phase dropping/adding and diode
emulation scheme to achieve extremely fast transient
response with fewer output capacitors and high efficiency
from light load to full load.
The ISL6336B is compliant with Intel’s VR11.1 specification.
Features include a pin (IMON) for current monitoring and a
Power State Indicator (PSI#) input pin to initiate a proprietary
phase dropping and diode emulation scheme for higher
efficiency at light load by dropping to 1- or 2-phase operation
with optional diode emulation to reduce switching and core
losses in the converter. After the PSI# signal is de-asserted,
the dropped phase(s) are added back to sustain heavy load
transient and efficiency.
Today’s microprocessors require a tightly regulated output
voltage position versus load current (droop). The ISL6336B
senses the output current continuously by utilizing patented
techniques to measure the voltage across a dedicated
current sense resistor or the DCR of the output inductor.
Current sensing provides the needed signals for precision
droop, channel-current balancing, and overcurrent
protection. A programmable integrated temperature
compensation function is implemented to effectively
compensate the temperature variation of the current sense
element. A current limit function provides overcurrent
protection for the individual phase.
FN6696.2
Features
• Intel VR11.1 Compliant
• H_CPURST_N Input to Eliminate Required Extensive
External Circuitry for Proper PSI# Operation of Intel’s
Eaglelake Chipset Platforms
• Proprietary Active Pulse Positioning and Pin Adaptive
Phase Alignment Modulation Scheme
• Proprietary Active Phase Adding and Dropping with Diode
Emulation for Enhanced Light Load Efficiency
• Precision Multiphase Core Voltage Regulation
- Differential Remote Voltage Sensing
- ±0.5% System Accuracy Over Life, Load, Line and
Temperature
- Bi-Directional Adjustable Reference-Voltage Offset
• Precision Resistor or DCR Current Sensing
- Accurate Load-Line Programming
- Accurate Channel-Current Balancing
- Accurate Current Monitoring Output Pin (IMON)
• Microprocessor Voltage Identification Input
- Dynamic VID™ Technology
- 8-Bit VID Input With VR11 Code
• Thermal Monitor and OV Protection with OVP Output
• Average Overcurrent Protection and Channel-Current Limit
• Precision Overcurrent Protection on IMON Pin
• Integrated Open Sense Line Protection
• Integrated Programmable Temperature Compensation
• 1- to 6-Phase Operation; Coupled Inductor Compatible
• Adjustable Switching Frequency up to 1MHz Per Phase
• Package Option
- QFN Compliant to JEDEC PUB95 MO-220 QFN - Quad
Flat No Leads - Product Outline
• Pb-Free (RoHS Compliant)
A unity gain, differential amplifier is provided for remote voltage
sensing and eliminates any potential difference between
remote and local grounds. This improves regulation and
protection accuracy. The threshold-sensitive enable input is
available to accurately coordinate the start up of the ISL6336B
with any other voltage rail. Dynamic-VID™ technology allows
seamless on-the-fly VID changes. The offset pin allows
accurate voltage offset settings that are independent of VID
setting.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2008, 2009, 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL6336B
Ordering Information
PART
NUMBER
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL6336BCRZ*
ISL6336B CRZ
0 to +70
48 Ld 7x7 QFN
L48.7x7
ISL6336BIRZ*
ISL6336B IRZ
-40 to +85
48 Ld 7x7 QFN
L48.7x7
*Add “-T” for tape and reel. Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J
STD-020.
Pinout
2
TM
VR_HOT
H_CPURST_N
VR_RDY
OVP
SS
FS
EN_VTT
EN_PWR
ISEN6+
ISEN6-
PWM6
ISL6336B
(48 LD QFN)
TOP VIEW
48
47
46
45
44
43
42
41
40
39
38
37
VID7
1
36 PWM3
VID6
2
35 ISEN3-
VID5
3
34 ISEN3+
VID4
4
33 ISEN1+
VID3
5
32 ISEN1-
VID2
6
31 PWM1
GND
VID1
7
VID0
8
29 ISEN4-
PSI#
9
28 ISEN4+
OFS 10
27 ISEN2+
IMON 11
26 ISEN2-
DAC 12
25 PWM2
13
14
15
16
17
18
19
20
21
22
23
24
REF
APA
COMP
FB
VDIFF
RGND
VSEN
TCOMP
VCC
ISEN5+
ISEN5-
PWM5
30 PWM4
FN6696.2
August 31, 2010
ISL6336B
Controller and Driver Recommendations
CONTROLLER
ISL6336B
DRIVER
COMMENTS
When PSI# is asserted (LOW), the controller generates a 3-level PWM pattern on the phases that are active in PSI# mode. The
active phases in PSI# mode must use VR11.1 drivers, ISL6622, ISL6620 for diode emulation.
GATE DRIVE
VOLTAGE
# OF GATE
DRIVES
DIODE
EMULATION
(DE)
GATE DRIVE
OPTIMIZATION
(GVOT)
COMMENTS
ISL6622,
ISL6622A,ISL6622B
12V
Dual Output
(Single Phase)
Yes
Yes
For phases that are active in PSI# mode and its coupled
channel in coupled inductor applications. Can also be
used on all channels.
ISL6620, ISL6620A
5V
Dual Output
(Single Phase)
Yes
No
For phases that are active in PSI# mode and its coupled
channel in coupled inductor applications. Can also be
used on all channels.
ISL6612, ISL6612A
12V
Dual Output
(Single Phase)
No
No
Can be used with phases that are inactive in PSI# mode
ISL6596, ISL6609
5V
Dual Output
(Single Phase)
No
No
Can be used with phases that are inactive in PSI# mode
ISL6614, ISL6614A
12V
Quad Output
(Two Phase)
No
No
Can be used with phases that are inactive in PSI# mode
ISL6610, ISL6610A
5V
Quad Output
(Two Phase)
No
No
Can be used with phases that are inactive in PSI# mode
NOTE: Intersil 5V and 12V drivers are mostly pin-to-pin compatible and allow for dual footprint layout implementation to optimize MOSFET selection and
efficiency. Dual = One Synchronous Channel; Quad = Two Synchronous Channels.
3
FN6696.2
August 31, 2010
ISL6336B
ISL6336B Block Diagram
VDIFF
VR_RDY
OVP
H_CPURST_N
VCC
PSI# APA
0.875V
RGND
POWER-ON
x1
VSEN
S
OVP
DRIVE
EN_VTT
RESET (POR)
R
0.875V
Q
EN_PWR
OVP
TRI-STATE
SOFT-START
AND
FAULT LOGIC
+175mV
CLOCK,
RAMP GENERATOR,
APA CONTROL
SS
OFS
OFFSET
FS
APP AND APA
MODULATOR
PWM1
APP AND APA
MODULATOR
PWM2
APP AND APA
MODULATOR
PWM3
APP AND APA
MODULATOR
PWM4
APP AND APA
MODULATOR
PWM5
APP AND APA
MODULATOR
PWM6
REF
DAC
VID7
VID6
VID5
DYNAMIC
VID
DAC
VID4
VID3
VID2
E/A
VID1
VID0
CHANNEL CURRENT
BALANCE AND
CURRENT LIMIT
COMP
CHANNEL
DETECT
ISEN1+
FB
ISEN1I_TRIP
1.12V
OC2
OC1
1
N
ISEN2+
∑
TEMPERATURE
COMPENSATION
IMON
1.12V
CHANNEL
ISEN2-
CURRENT
ISEN3+
SENSE
ISEN3ISEN4+
I_TOT
ISEN4ISEN5+
THERMAL
MONITORING
TEMPERATURE
COMPENSATION
GAIN
ISEN5ISEN6+
ISEN6-
GND
4
TM
VR_HOT
TCOMP
FN6696.2
August 31, 2010
ISL6336B
Typical Application - 5-Phase Buck Converter with Thermal Compensation
+5V
ISL6620
VCC
BOOT
UGATE
EN
PHASE
PWM
+5V
GND
LGATE
+5V
ISL6596
COMP APA REF
FB
VSEN
VTT
EN
PHASE
GND
GND
EN_VTT
ISL6596
VCC
BOOT
UGATE
EN
PHASE
PWM1
VID6
ISEN1ISEN1+
VID5
VID4
VID3
VID2
PWM4
ISEN4ISEN4+
VID1
VID0
PSI#
OVP
PWM
GND
PWM2
ISEN2ISEN2+
+5V
PWM5
IMON
PWM3
ISEN3-
VCC
BOOT
UGATE
EN
PHASE
H_CPURST_N
PWM6
ISEN6ISEN6+
VR_HOT
EN_PWR
TCOMP OFS FS
+5V
PWM
GND
ISEN3+
RT
R SS
VIN
VCC
BOOT
UGATE
EN
PHASE
PWM
GND
VIN
µP
LOAD
LGATE
ISL6596
SS
+5V
R OFS
+5V
+5V
VIN
LGATE
ISL6596
ISEN5ISEN5+
TM
LGATE
+5V
ISL6336B
VID7
BOOT
UGATE
VIN
VCC
RGND
VR_RDY
VCC
PWM
DAC
VDIFF
VIN
VIN
LGATE
NTC
5
FN6696.2
August 31, 2010
ISL6336B
Typical Application - 4-Phase Buck Converter with Coupled Inductors
+5V
ISL6620
VCC
BOOT
UGATE
EN
PHASE
PWM
+5V
GND
+5V
FB
COMP APA REF
VDIFF
VSEN
VTT
BOOT
UGATE
EN
PHASE
VIN
LGATE
VCC
RGND
GND
EN_VTT
VR_RDY
VCC
GND
DAC
LGATE
ISL6620
PWM
VIN
ISL6336B
VID7
PWM1
VID6
ISEN1ISEN1+
VID5
VID4
VID3
VID2
+5V
ISL6596
PWM3
ISEN3ISEN3+
VID1
VID0
PSI#
OVP
PWM2
ISEN2ISEN2+
ISEN4-
+5V
PWM5
ISEN5ISEN5+
PWM6
ISEN6ISEN6+
VR_HOT
TM
EN_PWR
TCOMP OFS FS
+5V
EN
PHASE
GND
ISEN4+
H_CPURST_N
BOOT
UGATE
PWM
PWM4
IMON
VCC
+5V
LGATE
ISL6596
VCC
BOOT
UGATE
EN
PHASE
PWM
GND
VIN
µP
LOAD
VIN
LGATE
SS
+5V
R OFS
RT
R SS
VIN
NTC
+5V +5V
6
FN6696.2
August 31, 2010
ISL6336B
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+6V
All Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.3V to VCC + 0.3V
Thermal Resistance (Typical, Notes 1, 2) θJA (°C/W) θJC (°C/W)
48 Ld QFN Package. . . . . . . . . . . . . . .
29
2
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Ambient Temperature
ISL6336BCRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
ISL6336BIRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications
Operating Conditions: VCC = 5V, Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7) UNITS
VCC SUPPLY CURRENT
Nominal Supply
VCC = 5VDC; EN_PWR = 5VDC; RT = 100kΩ,
ISEN1 = ISEN2 = ISEN3 = ISEN4 = ISEN5 = ISEN6 = 80µA
-
16
20
mA
Shutdown Supply
VCC = 5VDC; EN_PWR = 0VDC; RT = 100kΩ
-
14
17
mA
VCC Rising
4.3
4.4
4.5
V
VCC Falling
3.75
3.88
4.0
V
Rising
0.875
0.897
0.920
V
Falling
0.735
0.752
0.770
V
Rising
0.875
0.897
0.920
V
Falling
0.735
0.752
0.770
V
POWER-ON RESET AND ENABLE
POR Threshold
EN_PWR Threshold
EN_VTT Threshold
REFERENCE VOLTAGE AND DAC
System Accuracy of ISL6336BCRZ
(VID = 1V to 1.6V), TJ = 0°C to +70°C
(Notes 3, 4)
-0.5
-
0.5
%VID
System Accuracy of ISL6336BCRZ
(VID = 0.5V to 1V), TJ = 0°C to +70°C
(Notes 3, 4)
-5
-
5
mV
System Accuracy of ISL6336BIRZ
(VID = 1V to1.6V), TJ = -40°C to +85°C
(Notes 3, 4)
-0.6
-
0.6
%VID
System Accuracy of ISL6336BIRZ
(VID = 0.8V to 1V), TJ = -40°C to +85°C
(Notes 3, 4)
-0.7
-
0.7
%VID
System Accuracy of ISL6336BIRZ
(VID = 0.5V to 0.8V), TJ = -40°C to +85°C
(Notes 3, 4)
-1
-
1
%VID
VID Pull-up
After tD3 (see “Soft-Start” on page 20)
30
40
50
µA
VID Input Low Level
-
-
0.4
V
VID Input High Level
0.8
-
-
V
Maximum DAC Source Current
3.5
-
-
mA
Maximum DAC Sink Current
100
-
-
µA
50
-
-
µA
Maximum REF Source/Sink Current
7
(Note 4)
FN6696.2
August 31, 2010
ISL6336B
Electrical Specifications
Operating Conditions: VCC = 5V, Unless Otherwise Specified. (Continued)
PARAMETER
TEST CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7) UNITS
390
400
415
mV
1.574
1.60
1.635
V
PIN-ADJUSTABLE OFFSET
Voltage at OFS Pin
Offset resistor connected to ground
Voltage below VCC, offset resistor connected to VCC
OSCILLATORS
Accuracy of Switching Frequency Setting
RT = 100kΩ
225
250
275
kHz
Adjustment Range of Switching Frequency
(Note 4)
0.08
-
1.0
MHz
Soft-Start Ramp Rate
RSS = 100kΩ (Notes 5, 6)
Adjustment Range of Soft-Start Ramp Rate
(Note 4)
-
1.563
-
mV/µs
0.625
-
6.25
mV/µs
-
1.5
-
V
PWM GENERATOR
Sawtooth Amplitude
ERROR AMPLIFIER
Open-Loop Gain
RL = 10kΩ to ground
-
96
-
dB
Open-Loop Bandwidth
CL = 100pF, RL = 10kΩ to ground
-
80
-
MHz
Slew Rate
CL = 100pF
-
25
-
V/µs
Maximum Output Voltage
3.8
4.4
4.9
V
Output High Voltage @ 2mA
3.6
-
-
V
Output Low Voltage @ 2mA
-
-
1.6
V
-
20
-
MHz
REMOTE-SENSE AMPLIFIER
Bandwidth
Output High Current
VSEN - RGND = 2.5V
-500
-
500
µA
Output High Current
VSEN - RGND = 0.6V
-500
-
500
µA
-
50
-
µA
APA INPUT
APA Sink Current
PWM OUTPUT
Sink Impedance
PWM = LOW with 1mA load
100
220
300
Ω
Source Impedance
PWM = HIGH, forced to 3.7V
200
320
400
Ω
Threshold HIGH
-
-
0.8
V
Threshold LOW
0.4
-
-
V
38
-
60
ms
-
-
0.8
V
0.4
-
-
V
ISEN1 = ISEN2 = ISEN3 = ISEN4 = ISEN5 = ISEN6 = 40µA;
Offset and Mirror Error Included, RISENx = 200Ω
36.5
-
42
µA
ISEN1 = ISEN2 = ISEN3 = ISEN4 = ISEN5 = ISEN6 = 80µA;
Offset and Mirror Error Included, RISENx = 200Ω
74
-
83
µA
Overcurrent Trip Level for Average Current
(PSI# = 1)
Offset and Mirror Error Included, RISENx = 200Ω
96
105
117
µA
Overcurrent Trip Level for Average Current
(PSI# = 0)
Number of Phases = 6, Drop to 1-Phase
-
135
-
µA
PSI# INPUT
H_CPURST_N INPUT
PSI# Time Out
With Respect to H_CPURST_N Rising Edge
HIGH Signal Threshold
LOW Signal Threshold (PSI# Lockout)
CURRENT SENSE AND OVERCURRENT PROTECTION
Sensed Current Tolerance
8
FN6696.2
August 31, 2010
ISL6336B
Electrical Specifications
Operating Conditions: VCC = 5V, Unless Otherwise Specified. (Continued)
MIN
(Note 7)
TYP
Peak Current Limit for Individual Channel
115
129
146
µA
IMON Voltage Clamp and OCP Trip Level
1.085
1.11
1.14
V
TM Input Voltage for VR_HOT Trip
32.9
33.3
33.7
%VCC
TM Input Voltage for VR_HOT Reset
38.7
39.1
39.6
%VCC
PARAMETER
TEST CONDITIONS
MAX
(Note 7) UNITS
THERMAL MONITORING AND FAN CONTROL
Leakage Current of VR_HOT
With external pull-up resistor connected to VCC
-
-
5
µA
VR_HOT Low Voltage
With 1.24kΩ resistor pull-up to VCC, IVR_HOT = 4mA
-
-
0.3
V
Leakage Current of VR_RDY
With external pull-up resistor connected to VCC
-
-
5
µA
VR_RDY Low Voltage
IVR_RDY = 4mA
-
-
0.3
V
Undervoltage Threshold
VDIFF Falling
48
50
52
%VID
VR_RDY Reset Voltage
VDIFF Rising
57
59.6
62
%VID
Overvoltage Protection Threshold
Before valid VID
1.250
1.273
1.300
V
158
175
190
mV
-
100
-
mV
-
0.106
0.16
V
VR READY AND PROTECTION MONITORS
After valid VID, the voltage above VID
Overvoltage Protection Reset Hysteresis
OVP Output Low Voltage
IOVP = 4mA
NOTES:
3. These parts are designed and adjusted for accuracy with all errors in the voltage loop included.
4. Limits are established by characterization and are not production tested.
5. During soft-start, VDAC rises from 0 to 1.1V first and then ramp to VID voltage after receiving valid VID input.
6. Soft-start ramp rate is determined by the adjustable soft-start oscillator frequency at the speed of 6.25mV per cycle.
7. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
9
FN6696.2
August 31, 2010
ISL6336B
Functional Pin Description
VCC - Supplies the power necessary to operate the chip.
The controller starts to operate when the voltage on this pin
exceeds the rising POR threshold and shuts down when the
voltage on this pin drops below the falling POR threshold.
Connect this pin directly to a +5V supply. Place a R/C filter
right next to this pin for noise decoupling. The resistor and
capacitor should be placed right next to the VCC pin to GND.
GND - Bias and reference ground for the IC. The exposed
metal pad on the bottom of the package of the ISL6336B is
GND.
EN_PWR - This pin is a threshold-sensitive enable input for
the controller. Connecting the 12V supply to EN_PWR
through an appropriate resistor divider provides a means to
synchronize power-up of the controller and the MOSFET
driver ICs. When EN_PWR is driven above 0.875V, the
ISL6336B is active depending on status of the EN_VTT, the
internal POR, and pending fault states. Driving EN_PWR
below 0.745V will clear all fault states and prime the
ISL6336B to soft-start when re-enabled.
EN_VTT - This pin is another threshold-sensitive enable
input for the controller. It’s typically connected to VTT output
of VTT voltage regulator in the computer mother board.
When EN_VTT is driven above 0.875V, the ISL6336B is
active depending on status of ENLL, the internal POR, and
pending fault states. Driving EN_VTT below 0.745V will clear
all fault states and prime the ISL6336B to soft-start when
re-enabled.
FS - Use this pin to set up the desired switching frequency. A
resistor, placed from FS to GND or VCC will set the
switching frequency. The relationship between the value of
the resistor and the switching frequency is shown in
Equation 3. This pin is also used in combination with SS and
PSI# to determine phase dropping operation. See Table 1.
SS - Use this pin to set up the desired start-up oscillator
frequency. A resistor, placed from SS to GND or VCC will set
up the soft-start ramp rate. The relationship between the
value of the resistor and the soft-start ramp up time is
described in Equations 15 and 16. This pin is also used with
FS and PSI# pins to determine phase dropping operation.
See Table 1.
VID[7:0] - These are the inputs to the internal DAC that
generates the reference voltage for output regulation. The
pins have a minimum 30µA pull-up to about 1V after tD3.
There is no internal pull-up before tD3. Connect these pins to
open-drain outputs with external pull-up resistors or to active
pull-up outputs. The VID pins can be pulled as high as VCC
plus 0.3V.
VDIFF, VSEN, and RGND - VSEN and RGND form the
precision differential remote-sense amplifier. This amplifier
converts the differential voltage of the remote output to a
single-ended voltage referenced to local ground. VDIFF is the
10
amplifier’s output and the input to the regulation and protection
circuitry. Connect VSEN and RGND to the sense pins of the
remote load. VDIFF is connected to FB through a resistor.
FB and COMP - The inverting input and the output of the
error amplifier respectively. FB can be connected to VDIFF
through a resistor. A properly chosen resistor between
VDIFF and FB can set the load line (droop). The droop scale
factor is set by the ratio of the ISEN resistors and the
inductor DCR or the dedicated current sense resistor. COMP
is tied back to FB through an external R-C network to
compensate the regulator.
DAC and REF - The DAC pin is the output of the precision
internal DAC reference. The REF pin is the positive input of
the Error Amplifier. In typical applications, a 1kΩ, 1% resistor
is used between DAC and REF to generate a precision offset
voltage. This voltage is proportional to the offset current
determined by the offset resistor from OFS to ground or VCC.
A capacitor is used between REF and ground to smooth the
voltage transition during Dynamic VID™ operations.
PWM[6:1] - Pulse width modulation outputs. Connect these
pins to the PWM input pins of the Intersil driver IC. The
number of active channels is determined by the state of
PWM3, PWM4, PWM5, and PWM6. Tie PWM3 to VCC to
configure for 2-phase operation. Tie PWM4 to VCC to
configure for 3-phase operation. Tie PWM5 to VCC to
configure for 4-phase operation. Tie PWM6 to VCC to
configure for 5-phase operation. PWM firing order is
sequential from 1 to n with n being the number of active
phases.
ISEN[6:1]+, ISEN[6:1]- - The ISEN+ and ISEN- pins are
current sense inputs to individual differential amplifiers. The
sensed current is used for channel current balancing,
overcurrent protection, and droop regulation. Inactive
channels should have their respective current sense inputs
left open (for example, open ISEN6+ and ISEN6- for 5-phase
operation).
For DCR sensing, connect each ISEN- pin to the node
between the RC sense elements. Tie the ISEN+ pin to the
other end of the sense capacitor through a resistor, RISEN.
The voltage across the sense capacitor is proportional to the
inductor current. Therefore, the sense current is proportional
to the inductor current, and scaled by the DCR of the
inductor and RISEN.
To match the time delay of the internal circuit, a capacitor is
needed between each ISEN+ pin and GND as described in
“Current Sensing” on page 14.
VR_RDY - VR_RDY indicates that the soft-start is completed
and the output voltage is within the regulated range around
VID setting. It is an open-drain logic output. When OCP or
OVP occurs, VR_RDY will be pulled to low. It will also be
pulled low if the output voltage is below the undervoltage
threshold.
FN6696.2
August 31, 2010
ISL6336B
OFS - The OFS pin provides a means to program a DC
offset current for generating a DC offset voltage at the REF
input. The offset current is generated via an external resistor
and precision internal voltage references. The polarity of the
offset is selected by connecting the resistor to GND or VCC.
For no offset, the OFS pin should be left unterminated.
TCOMP - Temperature compensation scaling input. The
voltage sensed on the TM pin is utilized as the temperature
input to adjust IDROOP and the overcurrent protection limit to
effectively compensate for the temperature coefficient of the
current sense element. To implement the integrated
temperature compensation, a resistor divider circuit is needed
with one resistor being connected from TCOMP to VCC of the
controller and another resistor being connected from TCOMP
to GND. Changing the ratio of the resistor values will set the
gain of the integrated thermal compensation. When integrated
temperature compensation function is not used, connect
TCOMP to GND.
OVP - The overvoltage protection output indication pin. This
pin can be pulled to VCC and is latched when an overvoltage
condition is detected. When the OVP indication is not used,
keep this pin open.
IMON - IMON is a current output of the average of the sum
of each phase’s sensed current. A resistor connected from
IMON to GND will produce a voltage that is proportional to
the regulator current. The voltage at this pin is internally
clamped to 1.12V. If the voltage reaches 1.12V the clamp is
activated an overcurrent shutdown will be initiated.
Place a resistor from this pin to GND. A capacitor in parallel
with this resistor is required. The capacitor should be sized
for a minimum time constant of 300µs.
TM - TM is an input pin for VR temperature measurement.
Connect this pin through NTC thermistor to GND and a resistor
to VCC of the controller. The voltage at this pin is reverse
proportional to the VR temperature. ISL6336B monitors the VR
temperature based on the voltage at the TM pin and the output
signal at VR_HOT.
VR_HOT - VR_HOT is used as an indication of high VR
temperature. It is an open-drain logic output. It will be open
when the measured VR temperature reaches a certain level.
PSI# - The PSI# pin is used to change the state of the
controller. When PSI# is asserted the controller will change
the operating state to improve light load efficiency. The
controller drops the number of active phases to 1-phase or
2-phase operation with diode emulation according to the logic
shown in Table 1. The FS and SS pins are used to optimize
light load efficiency for non-coupled inductor, 2-phase coupled
inductor, and (n-x)-phase coupled inductor applications. The
controller resumes normal operation when this pin is pulled
HIGH. This pin has a 40µA internal pull-up to about 1V.
11
H_CPURST_N - This pin determines whether the PSI# input
is recognized and the IC enters the low-power, phase
dropping state. While in a logic LOW state and for 45ms
(typically) after returning HIGH, the controller will be
prevented from entering low power mode of operation by
locking out the PSI# input. Left open at start-up, this pin is
pulled to about 1.2V by an internal current source, and the
PSI# input is locked out for 45ms. To disable this functionality
at all times, connect this pin to VCC. See the “PWM and PSI#
Operation” on page 12 for details.
APA - The APA pin is used to adjust the Adaptive Phase
Alignment trip level. A 50µA current source flows into this pin.
A resistor connected from this pin to COMP sets the voltage
trip level. A small decoupling capacitor should be placed in
parallel with the resistor for high frequency decoupling.
Operation
Multiphase Power Conversion
Microprocessor load current profiles have changed to the
point that the advantages of multiphase power conversion
are impossible to ignore. The technical challenges
associated with producing a single-phase converter which is
both cost-effective and thermally viable, have forced a
change to the cost-saving approach of multiphase. The
ISL6336B controller helps reduce the complexity of
implementation by integrating vital functions and requiring
minimal output components. The block diagrams on page 5
and 6 provide top level views of multiphase power
conversion using the ISL6336B controller.
Interleaving
The switching of each channel in a multiphase converter is
timed to be symmetrically out of phase with each of the other
channels. In a 3-phase converter for example, each channel
switches 1/3 cycle after the previous channel and 1/3 cycle
before the following channel. As a result, the three-phase
converter has a combined ripple frequency three times
greater than the ripple frequency of any one phase. In
addition, the peak-to-peak amplitude of the combined
inductor current is reduced in proportion to the number of
phases (see Equations 1 and 2). The increased ripple
frequency and the lower ripple amplitude mean that the
designer can use less per-channel inductance and lower
total output capacitance for any performance specification.
Figure 1 illustrates the multiplicative effect on output ripple
frequency. The three channel currents (IL1, IL2, and IL3)
combine to form the AC ripple current and the DC load
current. The ripple component has three times the ripple
frequency of each individual channel current. Each PWM
pulse is triggered 1/3 of a cycle after the start of the PWM
pulse of the previous phase. The DC components of the
inductor currents combine to feed the load.
FN6696.2
August 31, 2010
ISL6336B
To understand the reduction of the ripple current amplitude in
the multiphase circuit, examine Equation 1, which represents
an individual channel’s peak-to-peak inductor current.
( V IN – V OUT ) ⋅ V OUT
I PP = --------------------------------------------------------L ⋅ fS ⋅ V
(EQ. 1)
IN
In Equation 1, VIN and VOUT are the input and the output
voltages respectively, L is the single-channel inductor value,
and fS is the switching frequency.
IL1 + IL2 + IL3, 7A/DIV
IL3, 7A/DIV
PWM3, 5V/DIV
IL2, 7A/DIV
PWM2, 5V/DIV
IL1, 7A/DIV
PWM1, 5V/DIV
1µs/DIV
FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS
FOR 3-PHASE CONVERTER
( V IN – ( N ⋅ V OUT ) ) ⋅ V OUT
I C ( P-P ) = -----------------------------------------------------------------------L ⋅ fS ⋅ V
(EQ. 2)
IN
Another benefit of interleaving is to reduce the input ripple
current. The input capacitance is determined in part by the
maximum input ripple current. Multi-phase topologies can
improve the overall system cost and size by lowering the
input ripple current and allowing the designer to reduce the
cost of input capacitance. The example in Figure 2 illustrates
the input currents from a three-phase converter combining to
reduce the total input ripple current.
The converter depicted in Figure 2 delivers 36A to a 1.5V load
from a 12V input. The RMS input capacitor current is 5.9A.
Compare this to a single-phase converter also stepping down
12V to 1.5V at 36A. The single-phase converter has 11.9ARMS
input capacitor current. The single-phase converter must use
an input capacitor bank with twice the RMS current capacity as
the equivalent 3-phase converter.
Figures 21, 22 and 23 in the section entitled “Input Capacitor
Selection” on page 29 can be used to determine the input
capacitor RMS current based on the load current, the duty
cycle, and the number of channels. They are provided as
aids in determining the optimal input capacitor solution.
Figure 24 shows the single phase input-capacitor RMS
current for comparison.
PWM Modulation Scheme
INPUT-CAPACITOR CURRENT 10A/DIV
CHANNEL 3
INPUT CURRENT
10A/DIV
CHANNEL 2
INPUT CURRENT
10A/DIV
CHANNEL 1
INPUT CURRENT
10A/DIV
The ISL6336B adopts Intersil's proprietary Active Pulse
Positioning (APP) modulation scheme to improve the
transient performance. APP control is a unique dual-edge
PWM modulation scheme with both PWM leading and
trailing edges being independently moved to provide the
best response to the transient loads. The PWM frequency,
however, is constant and set by the external resistor
between the FS pin and GND.
To further improve the transient response, the ISL6336B also
implements Intersil's proprietary Adaptive Phase Alignment
(APA) technique. The APA, with sufficiently large load step
currents, can turn on all phases simultaneously.
1µs/DIV
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
The output capacitors conduct the ripple component of the
inductor current. In the case of multiphase converters, the
capacitor current is the sum of the ripple currents from each of
the individual channels. Compare Equation 1 to the expression
for the peak-to-peak current after the summation of N
symmetrically phase-shifted inductor currents in Equation 2.
Peak-to-peak ripple current decreases by an amount
proportional to the number of channels. Output-voltage ripple is
a function of capacitance, capacitor equivalent series
resistance (ESR), and inductor ripple current. Reducing the
inductor ripple current allows the designer to use fewer or less
costly output capacitors.
12
With both APP and APA control, ISL6336B can achieve
excellent transient performance and reduce the demand on
the output capacitors.
Under steady state conditions the operation of the ISL6336B
PWM modulator appears to be that of a conventional trailing
edge modulator. Conventional analysis and design methods
can therefore be used for steady state and small signal
operation.
PWM and PSI# Operation
The timing of each converter is set by the number of active
channels. The default channel setting for the ISL6336B is
six. The switching cycle is defined as the time between PWM
pulse termination signals of each channel. The cycle time of
the pulse termination signal is the inverse of the switching
FN6696.2
August 31, 2010
ISL6336B
frequency set by the resistor between the FS pin and
ground. The PWM signals command the MOSFET drivers to
turn on/off the channel MOSFETs.
In the default 6-phase operation, the PWM2 pulse happens
1/6 of a cycle after PWM1, the PWM3 pulse happens 1/6 of
a cycle after PWM2, etc.
The ISL6336B works in a 1- to 6-phase configuration.
Connecting the PWM6 pin to VCC selects 5-phase operation
and the pulse times are spaced in 1/5 cycle increments.
Connecting the PWM5 pin to VCC selects 4-phase operation
and the pulse times are spaced in 1/4 cycle increments, etc.
When PSI# is pulled LOW, indicating low power operation of
the processor, the controller reduces the number of active
phases and operates 1- or 2-phases to improve efficiency
based on the logic in Table 2. Table 1 shows which phases
will be active when PSI# = 0 based on the phase count of the
application. For example, If operating in a 6-phase
configuration, phase 1 will be active if dropping to 1-phase
and phases 1 and 4 will be active if dropping to 2-phases.
TABLE 1. NUMBER OF ACTIVE PHASES AND PWM FIRING
SEQUENCE
PHASE
COUNT
PHASE
SEQUENCE
NORMAL
OPERATION
PWM/VCC
ACTIVE
PHASES
PSI# = 0
6-Phase
1-2-3-4-5-6
-
Phase 1/4
5-Phase
1-2-3-4-5
PWM6 = VCC
Phase 1/3
4-Phase
1 - 2 - 3- 4
PWM5:6 = VCC
Phase 1/3
3-Phase
1-2-3
PWM4:6 = VCC
Phase 1/2
2-Phase
1-2
PWM3:6 = VCC
Phase 1/2
1-Phase
1
PWM2:6 = VCC
-
TABLE 2. PHASE DROPPING BEHAVIOR
FS
SS
PSI# RESISTOR RESISTOR
CONFIGURATION
Non-CI or (N - 1) - CI Drops to 1-Phase
0
GND
GND
Non-CI or (N - 2) - CI Drops to 2-Phase
0
GND
VCC
2-Phase CI Drops to 1-Phase
0
VCC
GND
2-Phase CI Drops to 2-Phase
0
VCC
VCC
Normal PWM CCM Mode
1
x
x
The SS and FS pins are used to program the controllers PWM
behavior in configurations using standard inductors, 2-phase
coupled inductors or (N - 1)/(N - 2)-phase coupled inductors
when PSI# goes LOW. Two-phase coupled inductors refer to
inductor structures that magnetically couple 2-phases together.
(N - 1) and (N - 2) coupled inductors refer to structures that
couple all phases together except for the 1- or 2-phases that
remain active in PSI# mode. N refers to the programmed
number of active phases in normal operation, PSI# = 1 (See
Table 1). Each case yields different PWM output behavior on
13
both the dropped phase(s) and active phases as PSI# is
asserted and de-asserted. In Table 2, ‘VCC’ means that the
resistor is connected from the respective pin to VCC and ‘GND’
means the resistor is connected from the respective pin to
GND.
When PSI# goes LOW, the dropped phase’s PWM signal is
forced LOW for a minimum time, 200ns typically, and then is
driven to 1/2*VCC while the remaining active phase PWM(s)
sends out a repetitive 3-level PWM pattern that the
dedicated VR11.1 drivers (ISL6622/ISL6620) can decode
and then enter diode emulation mode.
During soft-start or overcurrent hiccup mode all phases will be
operating despite the state of the PSI# pin. Once VR_RDY is
asserted the state of the PSI# pin is considered. In addition, a
LOW signal at the H_CPURST_N pin disables PSI# mode.
The state of the PSI# signal will not be recognized as LOW
until approximately 45ms (see “Electrical Specifications” table
on page 7 for the delay time range) after H_CPURST_N
returns to a logic HIGH state. The LOW and HIGH thresholds
are 0.4V and 0.8V respectively. A logic LOW can be obtained
by pulling this pin to ground with a suitable small signal
device, while a logic HIGH can be obtained by leaving the pin
open or connecting to the processor VTT (~1.1V) via a
suitable pull-up. If the PSI# lockout is not desired at any time
during the operation of the IC, then connect H_CPURST_N to
VCC.
This unique function eliminates the required external
circuitry for proper PSI# operation of Intel’s Eaglelake
chipset platforms, reducing cost and PCB space. This
function can be disabled making the ISL6336B compatible
with the ISL6336 for other platform implementations.
A high PSI# input signal will force the controller back into
CCM normal operation and all phases will be activated to
sustain a heavy load transient and to increase efficiency at
higher loads.
While the controller is operational (VCC above POR,
EN_VTT and EN_PWR are both high, valid VID inputs), it
can pull the PWM pins to ~40% of VCC (~2V for 5V VCC
bias) during various stages, such as soft-start delay, phase
shedding operation, or fault conditions (OC or OV events).
The matching driver's internal PWM resistor divider can
further raise the PWM potential, but not lower it below the
level set by the controller IC. Therefore, the controller's
PWM outputs are directly compatible with Intersil drivers that
require 5V PWM signal amplitudes. Drivers requiring 3.3V
PWM signal amplitudes are generally incompatible.
Switching Frequency
The switching frequency is determined by the selection of
the frequency-setting resistor, RT, which is connected from
FS pin to GND or VCC (see “Typical Application - 5-Phase
Buck Converter with Thermal Compensation” on page 5 and
“Typical Application - 4-Phase Buck Converter with Coupled
FN6696.2
August 31, 2010
ISL6336B
Inductors” on page 6). Equation 3 is provided to assist in
selecting the correct resistor value.
10
2.5X10
R T = -------------------------F SW
(EQ. 3)
where FSW is the switching frequency of each phase.
Equation 3 also applies for connecting FS to VCC or GND.
Figure 3 shows the relationship between RT and FSW,
according to Equation 3.
1000
900
(EQ. 5)
If the R-C network components are selected such that the
RC time constant (= R*C) matches the inductor time
constant (= L/DCR), the voltage across the capacitor VC is
equal to the voltage drop across the DCR, i.e., proportional
to the channel-current.
700
600
500
400
300
200
50
60
RT (kΩ)
70
80
90
100
Equation 6 shows that the ratio of the channel current to the
sensed current ISEN is driven by the value of the sense
resistor and the DCR of the inductor.
FIGURE 3. SWITCHING FREQUENCY vs RT
Current Sensing
The ISL6336B senses current continuously for fast response.
The ISL6336B supports inductor DCR sensing, or resistor
sensing techniques. The associated channel current sense
amplifier uses the ISEN inputs to reproduce a signal
proportional to the inductor current, IL. The sensed current,
ISEN, is used for current balance, load-line regulation, and the
overcurrent protection.
The internal circuitry, shown in Figures 3 and 4, represents
one channel of an N-Channel converter. This circuitry is
repeated for each channel in the converter, but may not be
active depending on the status of the PWM2, PWM3,
PWM4, PWM5, PWM6 pins, “PWM and PSI# Operation” on
page 12.
The input bias current of the current sensing amplifier is
typically 60nA; less than 5kΩ input impedance is preferred to
minimize the offset error.
DCR
I SEN = I L ⋅ -----------------R
(EQ. 6)
ISEN
VIN
IL ( s )
L
ISL6609
DCR
VOUT
INDUCTOR
+
40
VL
VC(s)
+
30
R
PWM(n)
COUT
-
20
Because of the internal filter at the ISEN- pin, a capacitor,
CT, is needed to match the time delay between the ISENand ISEN+ signals. Select the proper CT to keep the time
constant of RISEN and CT (RISEN x CT) close to 27ns.
-
FSW (kHz)
L
⎛ s ⋅ ------------+ 1⎞ ⋅ ( DCR ⋅ I L )
⎝ DCR
⎠
V C = --------------------------------------------------------------------( s ⋅ RC + 1 )
With the internal low-offset current amplifier, the capacitor
voltage VC is replicated across the sense resistor RISEN.
Therefore the current out of ISEN+ pin, ISEN, is proportional
to the inductor current.
800
100
The voltage on the capacitor VC, can be shown to be
proportional to the channel current IL; see Equation 5.
C
ISL6336B
INTERNAL CIRCUIT
RISEN(n)
(PTC)
In
CURRENT
INDUCTOR DCR SENSING
An inductor’s winding is characteristic of a distributed
resistance as measured by the DCR (Direct Current
Resistance) parameter. Consider the inductor DCR as a
separate lumped quantity, as shown in Figure 4. The
channel-current IL, flowing through the inductor, will also
pass through the DCR. Equation 4 shows the S-domain
equivalent voltage across the inductor VL.
V L = I L ⋅ ( s ⋅ L + DCR )
(EQ. 4)
A simple R-C network across the inductor extracts the DCR
voltage, as shown in Figure 4.
14
ISEN-(n)
SENSE
+
-
ISEN+(n)
CT
DCR
I SEN = I ------------------LR
ISEN
FIGURE 4. DCR SENSING CONFIGURATION
RESISTIVE SENSING
For accurate current sense, a dedicated current-sense
resistor RSENSE in series with each output inductor can
serve as the current sense element (see Figure 5). This
technique is more accurate, but reduces overall converter
FN6696.2
August 31, 2010
ISL6336B
efficiency due to the additional power loss on the current
sense element RSENSE.
The same capacitor CT is needed to match the time delay
between ISEN- and ISEN+ signals. Select the proper CT to
keep the time constant of RISEN and CT (RISEN x CT) close
to 27ns.
Equation 7 shows the ratio of the channel current to the
sensed current ISEN.
R SENSE
I SEN = I L ⋅ ----------------------R ISEN
(EQ. 7)
I
L
L
RSENSE VOUT
COUT
ISL6336B
INTERNAL CIRCUIT
RISEN(n)
In
CURRENT
SENSE
ISEN-(n)
+
-
ISEN+(n)
CT
R SENSE
I SEN = I ------------------------L R
ISEN
FIGURE 5. SENSE RESISTOR IN SERIES WITH INDUCTORS
The inductor DCR value will increase as the temperature
increases. Therefore the sensed current will increase as the
temperature of the current sense element increases. In order
to compensate the temperature effect on the sensed current
signal, a Positive Temperature Coefficient (PTC) resistor can
be selected for the sense resistor RISEN, or the integrated
temperature compensation function of ISL6336B should be
utilized instead. The integrated temperature compensation
function is described in “External Temperature
Compensation” on page 24.
the error in the reference voltage (output of the DAC) and
offset errors in the OFS current source, remote-sense and
error amplifiers. Intersil specifies the guaranteed tolerance of
the ISL6336B to include the combined tolerances of each of
these elements.
The output of the error amplifier, VCOMP, is compared to the
sawtooth waveforms to generate the PWM signals. The
PWM signals control the timing of the Intersil MOSFET
drivers and regulate the converter output to the specified
reference voltage. The internal and external circuitries which
control the voltage regulation are illustrated in Figure 6.
The ISL6336B incorporates an internal differential remotesense amplifier in the feedback path. The amplifier removes
the voltage error encountered when measuring the output
voltage relative to the local controller ground reference point
resulting in a more accurate means of sensing output
voltage. Connect the microprocessor sense pins to the
non-inverting input, VSEN, and inverting input, RGND, of the
remote-sense amplifier. The remote-sense output, VDIFF, is
connected to the inverting input of the error amplifier through
an external resistor.
A digital-to-analog converter (DAC) generates a reference
voltage based on the state of logic signals at pins VID7
through VID0. The DAC decodes the 8-bit logic signal (VID)
into one of the discrete voltages shown in Table 3. Each VID
input has an internal 30µA minimum pull-up to VCC after
tD3. The pull-up current diminishes to zero above the logic
threshold (near 1V) to protect voltage-sensitive output
devices. External pull-up resistors can augment the pull-up
current sources in case the leakage into the driving device is
greater than 30µA.
EXTERNAL CIRCUIT
R C CC
COMP
DAC
RREF
Channel-Current Balance
The sensed current In from each active channel are summed
together and divided by the number of active channels. The
resulting average current IAVG provides a measure of the
total load current. Channel-current balance is achieved by
comparing the sensed current of each channel to the
average current to make an appropriate adjustment to the
PWM duty cycle of each channel with Intersil’s patented
current-balance method.
Channel-current balance is essential in achieving the
thermal advantage of multiphase operation. With good
current balance, the power loss is equally dissipated over
multiple devices and a greater area.
Voltage Regulation
The compensation network shown in Figure 6 assures that
the steady-state error in the output voltage is limited only to
15
ISL6336B
INTERNAL CIRCUIT
REF
CREF
+
-
FB
RFB
+
VDROOP
-
VOUT+
VOUT-
VCOMP
ERROR AMPLIFIER
VDIFF
IAVG
VSEN
+
RGND
DIFFERENTIAL
REMOTE-SENSE
AMPLIFIER
FIGURE 6. OUTPUT VOLTAGE AND LOAD-LINE
REGULATION WITH OFFSET ADJUSTMENT
FN6696.2
August 31, 2010
ISL6336B
TABLE 3. VR11 VID 8-BIT (Continued)
TABLE 3. VR11 VID 8-BIT
VID7
VID6
VID5
VID4
VID3
VID2
VID1
0
0
0
0
0
0
0
0
OFF
0
0
0
0
0
0
0
1
OFF
0
0
0
0
0
0
1
0
1.60000
0
0
0
0
0
0
1
1
1.59375
0
0
0
0
0
1
0
0
1.58750
0
0
0
0
0
1
0
1
1.58125
0
0
0
0
0
1
1
0
1.57500
0
0
0
0
0
1
1
1
1.56875
0
0
0
0
1
0
0
0
1.56250
0
0
0
0
1
0
0
1
1.55625
0
0
0
0
1
0
1
0
1.55000
0
0
0
0
1
0
1
1
1.54375
0
0
0
0
1
1
0
0
1.53750
0
0
0
0
1
1
0
1
1.53125
0
0
0
0
1
1
1
0
1.52500
0
0
0
0
1
1
1
1
1.51875
0
0
0
1
0
0
0
0
1.51250
0
0
0
1
0
0
0
1
1.50625
0
0
0
1
0
0
1
0
1.50000
0
0
0
1
0
0
1
1
1.49375
0
0
0
1
0
1
0
0
1.48750
0
0
0
1
0
1
0
1
1.48125
0
0
0
1
0
1
1
0
1.47500
0
0
0
1
0
1
1
1
1.46875
0
0
0
1
1
0
0
0
1.46250
0
0
0
1
1
0
0
1
1.45625
0
0
0
1
1
0
1
0
1.45000
0
0
0
1
1
0
1
1
1.44375
0
0
0
1
1
1
0
0
1.43750
0
0
0
1
1
1
0
1
1.43125
0
0
0
1
1
1
1
0
1.42500
0
0
0
1
1
1
1
1
1.41875
0
0
1
0
0
0
0
0
1.41250
0
0
1
0
0
0
0
1
1.40625
0
0
1
0
0
0
1
0
1.40000
0
0
1
0
0
0
1
1
1.39375
0
0
1
0
0
1
0
0
1.38750
0
0
1
0
0
1
0
1
1.38125
0
0
1
0
0
1
1
0
1.37500
16
VID0 VOLTAGE
VID7
VID6
VID5
VID4
VID3
VID2
VID1
VID0 VOLTAGE
0
0
1
0
0
1
1
1
1.36875
0
0
1
0
1
0
0
0
1.36250
0
0
1
0
1
0
0
1
1.35625
0
0
1
0
1
0
1
0
1.35000
0
0
1
0
1
0
1
1
1.34375
0
0
1
0
1
1
0
0
1.33750
0
0
1
0
1
1
0
1
1.33125
0
0
1
0
1
1
1
0
1.32500
0
0
1
0
1
1
1
1
1.31875
0
0
1
1
0
0
0
0
1.31250
0
0
1
1
0
0
0
1
1.30625
0
0
1
1
0
0
1
0
1.30000
0
0
1
1
0
0
1
1
1.29375
0
0
1
1
0
1
0
0
1.28750
0
0
1
1
0
1
0
1
1.28125
0
0
1
1
0
1
1
0
1.27500
0
0
1
1
0
1
1
1
1.26875
0
0
1
1
1
0
0
0
1.26250
0
0
1
1
1
0
0
1
1.25625
0
0
1
1
1
0
1
0
1.25000
0
0
1
1
1
0
1
1
1.24375
0
0
1
1
1
1
0
0
1.23750
0
0
1
1
1
1
0
1
1.23125
0
0
1
1
1
1
1
0
1.22500
0
0
1
1
1
1
1
1
1.21875
0
1
0
0
0
0
0
0
1.21250
0
1
0
0
0
0
0
1
1.20625
0
1
0
0
0
0
1
0
1.20000
0
1
0
0
0
0
1
1
1.19375
0
1
0
0
0
1
0
0
1.18750
0
1
0
0
0
1
0
1
1.18125
0
1
0
0
0
1
1
0
1.17500
0
1
0
0
0
1
1
1
1.16875
0
1
0
0
1
0
0
0
1.16250
0
1
0
0
1
0
0
1
1.15625
0
1
0
0
1
0
1
0
1.15000
0
1
0
0
1
0
1
1
1.14375
0
1
0
0
1
1
0
0
1.13750
0
1
0
0
1
1
0
1
1.13125
0
1
0
0
1
1
1
0
1.12500
FN6696.2
August 31, 2010
ISL6336B
TABLE 3. VR11 VID 8-BIT (Continued)
VID7
VID6
VID5
VID4
VID3
VID2
VID1
0
1
0
0
1
1
1
1
0
1
0
1
0
0
0
0
1
0
1
0
0
0
1
0
1
0
0
1
0
1
0
1
0
0
1
0
TABLE 3. VR11 VID 8-BIT (Continued)
VID7
VID6
VID5
VID4
VID3
VID2
VID1
1.11875
0
1
1
1
0
1
1
1
0.86875
0
1.11250
0
1
1
1
1
0
0
0
0.86250
0
1
1.10625
0
1
1
1
1
0
0
1
0.85625
0
1
0
1.10000
0
1
1
1
1
0
1
0
0.85000
0
0
1
1
1.09375
0
1
1
1
1
0
1
1
0.84375
1
0
1
0
0
1.08750
0
1
1
1
1
1
0
0
0.83750
0
1
0
1
0
1
1.08125
0
1
1
1
1
1
0
1
0.83125
1
0
1
0
1
1
0
1.07500
0
1
1
1
1
1
1
0
0.82500
0
1
0
1
0
1
1
1
1.06875
0
1
1
1
1
1
1
1
0.81875
0
1
0
1
1
0
0
0
1.06250
1
0
0
0
0
0
0
0
0.81250
0
1
0
1
1
0
0
1
1.05625
1
0
0
0
0
0
0
1
0.80625
0
1
0
1
1
0
1
0
1.05000
1
0
0
0
0
0
1
0
0.80000
0
1
0
1
1
0
1
1
1.04375
1
0
0
0
0
0
1
1
0.79375
0
1
0
1
1
1
0
0
1.03750
1
0
0
0
0
1
0
0
0.78750
0
1
0
1
1
1
0
1
1.03125
1
0
0
0
0
1
0
1
0.78125
0
1
0
1
1
1
1
0
1.02500
1
0
0
0
0
1
1
0
0.77500
0
1
0
1
1
1
1
1
1.01875
1
0
0
0
0
1
1
1
0.76875
0
1
1
0
0
0
0
0
1.01250
1
0
0
0
1
0
0
0
0.76250
0
1
1
0
0
0
0
1
1.00625
1
0
0
0
1
0
0
1
0.75625
0
1
1
0
0
0
1
0
1.00000
1
0
0
0
1
0
1
0
0.75000
0
1
1
0
0
0
1
1
0.99375
1
0
0
0
1
0
1
1
0.74375
0
1
1
0
0
1
0
0
0.98750
1
0
0
0
1
1
0
0
0.73750
0
1
1
0
0
1
0
1
0.98125
1
0
0
0
1
1
0
1
0.73125
0
1
1
0
0
1
1
0
0.97500
1
0
0
0
1
1
1
0
0.72500
0
1
1
0
0
1
1
1
0.96875
1
0
0
0
1
1
1
1
0.71875
0
1
1
0
1
0
0
0
0.96250
1
0
0
1
0
0
0
0
0.71250
0
1
1
0
1
0
0
1
0.95625
1
0
0
1
0
0
0
1
0.70625
0
1
1
0
1
0
1
0
0.95000
1
0
0
1
0
0
1
0
0.70000
0
1
1
0
1
0
1
1
0.94375
1
0
0
1
0
0
1
1
0.69375
0
1
1
0
1
1
0
0
0.93750
1
0
0
1
0
1
0
0
0.68750
0
1
1
0
1
1
0
1
0.93125
1
0
0
1
0
1
0
1
0.68125
0
1
1
0
1
1
1
0
0.92500
1
0
0
1
0
1
1
0
0.67500
0
1
1
0
1
1
1
1
0.91875
1
0
0
1
0
1
1
1
0.66875
0
1
1
1
0
0
0
0
0.91250
1
0
0
1
1
0
0
0
0.66250
0
1
1
1
0
0
0
1
0.90625
1
0
0
1
1
0
0
1
0.65625
0
1
1
1
0
0
1
0
0.90000
1
0
0
1
1
0
1
0
0.65000
0
1
1
1
0
0
1
1
0.89375
1
0
0
1
1
0
1
1
0.64375
0
1
1
1
0
1
0
0
0.88750
1
0
0
1
1
1
0
0
0.63750
0
1
1
1
0
1
0
1
0.88125
1
0
0
1
1
1
0
1
0.63125
0
1
1
1
0
1
1
0
0.87500
1
0
0
1
1
1
1
0
0.62500
17
VID0 VOLTAGE
VID0 VOLTAGE
FN6696.2
August 31, 2010
ISL6336B
VID7
VID6
VID5
VID4
VID3
VID2
VID1
1
0
0
1
1
1
1
1
0.61875
1
0
1
0
0
0
0
0
0.61250
1
0
1
0
0
0
0
1
0.60625
As shown in Figure 6, a current proportional to the average
current of all active channels, IAVG, flows from FB through a
load-line regulation resistor RFB. The resulting voltage drop
across RFB is proportional to the output current, effectively
creating an output voltage droop with a steady-state value
defined in Equation 8.
1
0
1
0
0
0
1
0
0.60000
V DROOP = I AVG ⋅ R FB
1
0
1
0
0
0
1
1
0.59375
1
0
1
0
0
1
0
0
0.58750
1
0
1
0
0
1
0
1
0.58125
1
0
1
0
0
1
1
0
0.57500
1
0
1
0
0
1
1
1
0.56875
1
0
1
0
1
0
0
0
0.56250
1
0
1
0
1
0
0
1
0.55625
1
0
1
0
1
0
1
0
0.55000
1
0
1
0
1
0
1
1
0.54375
1
0
1
0
1
1
0
0
0.53750
1
0
1
0
1
1
0
1
0.53125
1
0
1
0
1
1
1
0
0.52500
1
0
1
0
1
1
1
1
0.51875
1
0
1
1
0
0
0
0
0.51250
1
0
1
1
0
0
0
1
0.50625
1
0
1
1
0
0
1
0
0.50000
1
1
1
1
1
1
1
0
OFF
1
1
1
1
1
1
1
1
OFF
TABLE 3. VR11 VID 8-BIT (Continued)
VID0 VOLTAGE
Load-Line Regulation
Some microprocessor manufacturers require a precisely
controlled output resistance. This dependence of the output
voltage on the load current is often termed “droop” or “load
line” regulation. By adding a well controlled output impedance,
the output voltage can effectively be level shifted in a direction
which works to achieve the load-line regulation required by
these manufacturers.
In other cases, the designer may determine that a more
cost-effective solution can be achieved by adding droop.
Droop can help to reduce the output-voltage spike that
results from the fast changes of the load-current demand.
The magnitude of the spike is dictated by the ESR and ESL
of the output capacitors selected. By positioning the no-load
voltage level near the upper specification limit, a larger
negative spike can be sustained without crossing the lower
limit. By adding a well controlled output impedance, the
output voltage under load can effectively be level shifted
down so that a larger positive spike can be sustained without
crossing the upper specification limit.
18
(EQ. 8)
The regulated output voltage is reduced by the droop voltage
VDROOP. The output voltage as a function of load current is
derived by combining Equation 8 with the appropriate
sample current expression defined by the current sense
method employed.
RX
⎛ I OUT
⎞
V OUT = V REF – V OFS – ⎜ ------------- ⋅ ------------------ ⋅ R FB⎟
N
R
⎝
⎠
ISEN
(EQ. 9)
Where VREF is the reference voltage, VOFS is the
programmed offset voltage, IOUT is the total output current
of the converter, RISEN is the sense resistor connected to
the ISEN+ pin, and RFB is the feedback resistor, N is the
active channel number, and RX is the DCR, or RSENSE
depending on the sensing method.
Therefore the equivalent loadline impedance, i.e. Droop
impedance, is equal to Equation 10:
R FB
RX
R LL = ------------ ⋅ -----------------N
R ISEN
(EQ. 10)
Output-Voltage Offset Programming
The ISL6336B allows the designer to accurately adjust the
offset voltage. When resistor, ROFS, is connected between
OFS to VCC, the voltage across it is regulated to 1.6V. This
causes a proportional current (IOFS) to flow into OFS. If
ROFS is connected to ground, the voltage across it is
regulated to 0.4V, and IOFS flows out of OFS. A resistor
between DAC and REF, RREF, is selected so that the
product (IOFS x ROFS) is equal to the desired offset voltage.
These functions are shown in Figure 7.
Once the desired output offset voltage has been determined,
use Equations 11 and 12 to set ROFS:
For Positive Offset (connect ROFS to VCC):
1.6 ⋅ R REF
R OFS = ---------------------------V OFFSET
(EQ. 11)
For Negative Offset (connect ROFS to GND):
0.4 ⋅ R REF
R OFS = ---------------------------V OFFSET
(EQ. 12)
FN6696.2
August 31, 2010
ISL6336B
Operation Initialization
FB
DYNAMIC
VID D/A
Prior to converter initialization, proper conditions must exist on
the enable inputs and VCC. When the conditions are met, the
controller begins soft-start. Once the output voltage is within the
proper window of operation, VR_RDY asserts logic high.
DAC
RREF
E/A
+
REF
CREF
+
VCC
OR
GND
1.6V
-
+
+
ROFS
+
0.4V
VCC
-
ISL6336B
OFS
GND
FIGURE 7. OUTPUT VOLTAGE OFFSET PROGRAMMING
Dynamic VID
Modern microprocessors need to make changes to their
core voltage as part of the normal operation. They direct the
core-voltage regulator to do this by making changes to the
VID inputs during the regulator operation. The power
management solution is required to monitor the DAC inputs
and respond to on-the-fly VID changes in a controlled
manner. Supervising the safe output voltage transition within
the DAC range of the processor without discontinuity or
disruption is a necessary function of the core-voltage
regulator.
In order to ensure a smooth transition of output voltage
during VID change, a VID step change smoothing network,
composed of RREF and CREF, can be used. The selection of
RREF is based on the desired offset voltage as detailed
above in “Output-Voltage Offset Programming” on page 18.
The selection of CREF is based on the time duration for 1-bit
VID change and the allowable delay time.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met before the ISL6336B
is released from shutdown mode.
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6336B is guaranteed. Hysteresis between the
rising and falling thresholds assure that once enabled,
the ISL6336B will not inadvertently turn off unless the
bias voltage drops substantially (see “Electrical
Specifications” table beginning on page 7).
2. The ISL6336B features an enable input (EN_PWR) for
power sequencing between the controller bias voltage and
another voltage rail. The enable comparator holds the
ISL6336B in shutdown until the voltage at EN_PWR rises
above 0.875V. The enable comparator has about 130mV
of hysteresis to prevent bounce. It is important that the
driver ICs reach their POR level before the ISL6336B
becomes enabled. The schematic in Figure 8
demonstrates sequencing the ISL6336B with the ISL66xx
family of Intersil MOSFET drivers, which require 12V bias.
3. The voltage on EN_VTT must be higher than 0.875V to
enable the controller. This pin is typically connected to the
output of the VTT voltage regulator.
ISL6336B INTERNAL CIRCUIT
EXTERNAL CIRCUIT
+12V
VCC
POR
CIRCUIT
ENABLE
COMPARATOR
+
-
100kΩ
EN_PWR
9.1kΩ
0.875V
Assuming the microprocessor controls the VID change at
1-bit every tVID, the relationship between the time constant
of RREF and CREF network and tVID is given by Equation 13.
+
EN_VTT
-
(EQ. 13)
C REF ⋅ R REF = t VID
0.875V
During dynamic VID transition and VID up steps, the
overcurrent trip point increases by 140% to avoid false
triggering OCP circuits, while the overvoltage trip point is set
to its maximum VID OVP trip level. If dynamic VID occurs
when PSI# is asserted, the controller will activate all phases
and complete the transition at which point the status of the
PSI# pin will control operation.
19
SOFT-START
AND
FAULT LOGIC
FIGURE 8. POWER SEQUENCING USING THRESHOLD
SENSITIVE ENABLE (EN) FUNCTION
FN6696.2
August 31, 2010
ISL6336B
When all conditions above are satisfied, ISL6336B begins
soft-start and ramps the output voltage to 1.1V first. After
remaining at 1.1V for some time, ISL6336B reads the VID
code at VID input pins. If the VID code is valid, ISL6336B will
regulate the output to the final VID setting. If the VID code is
an OFF code, ISL6336B will shut down, and cycling VCC,
EN_PWR or EN_VTT is needed to restart.
Soft-Start
ISL6336B based VR has 4 periods during soft-start as
shown in Figure 9. After VCC, EN_VTT and EN_PWR reach
their POR/enable thresholds, The controller will have fixed
delay period tD1. After this delay period, the VR will begin
first soft-start ramp until the output voltage reaches 1.1V
VBOOT voltage. Then, the controller will regulate the VR
voltage at 1.1V for another fixed period tD3. At the end of tD3
period, ISL6336B reads the VID signals. If the VID code is
valid, ISL6336B will initiate the second soft-start ramp until
the voltage reaches the VID voltage minus the offset voltage.
tD2
tD3 tD4
Current Sense Output
The current sourced at the IMON pin is equal to the sensed
average current inside the ISL6336B, IAVG. In a typical
application, a resistor is placed from the IMON pin to GND to
generate a voltage which is proportional to the load current
as shown in Equation 17:
RX
R IMON
V IMON = ------------------- ⋅ ------------------ ⋅ I OUT
N
R ISEN
(EQ. 17)
The resistor from the IMON pin to GND should be chosen to
ensure that the voltage at the IMON pin is less than 1.12V
under the maximum load current. The IMON pin voltage is
clamped at a maximum of 1.12V. Once the 1.12V threshold
is reached, an overcurrent shutdown will be initiated as
described in “Overcurrent Protection” on page 21.
tD5
EN_VTT
VR_RDY
500µs/DIV
FIGURE 9. SOFT-START WAVEFORMS
The soft-start time is the sum of the 4 periods as shown in
Equation 14:
t SS = t D1 + t D2 + t D3 + t D4
After the DAC voltage reaches the final VID setting,
VR_RDY will be set to high with the fixed delay tD5. The
typical value for tD5 is 85µs. Before VR_RDY is released,
the controller disregards the PSI# input and always operates
in normal CCM PWM mode.
where VIMON is the voltage at the IMON pin, RIMON is the
resistor between IMON and GND, IOUT is the total output
current of the converter, RISEN is the sense resistor
connected to the ISEN+ pin, N is the active channel number
and RX is the DC resistance of the current sense element.
VOUT, 500mV/DIV
A small capacitor can be placed between the IMON pin and
GND to reduce noise. In addition, some applications will
require the VIMON signal to be filtered with a minimum time
constant. The filter capacitor can be chosen appropriately
based on the RIMON value to set the desired time constant.
(EQ. 14)
tD1 is a fixed delay with a typical value as 1.36ms. tD3 is
determined by a fixed 85µs plus the time to obtain valid VID
voltage. If the VID is valid before the output reaches the
1.1V, the minimum time to validate the VID input is 500ns.
Therefore the minimum tD3 is about 86µs.
During tD2 and tD4, ISL6336B digitally controls the DAC
voltage change at 6.25mV per step. The time for each step is
determined by the frequency of the soft-start oscillator, which
is defined by a resistor RSS from SS pin to GND or VCC. The
equations are the same for the case where RSS is connected
to GND or VCC. The two soft-start ramp times tD2 and tD4 can
be calculated based on the Equations 15 and 16:
1.1 ⋅ R SS
t D2 = ------------------------ ( μs )
6.25 ⋅ 25
(EQ. 15)
( ( V VID – 1.1 ) ⋅ R SS )
t D4 = ------------------------------------------------------ ( μs )
6.25 ⋅ 25
(EQ. 16)
20
IMON VOLTAGE
tD1
For example, when VID is set to 1.5V and the RSS is set at
100kΩ, the first soft-start ramp time tD2 will be 704µs and the
second soft-start ramp time tD4 will be 256µs.
0V
VIMON_OFS
0A LOAD INCREASING
FIGURE 10. IMON VOLTAGE vs OUTPUT CURRENT
The voltage at the IMON pin will vary linearly with output
current, as shown in Figure 10 with some tolerance. Some
applications may require the addition of a positive offset on
FN6696.2
August 31, 2010
ISL6336B
IMON to offset for the tolerance at the maximum IMON
voltage value. This can be done by connecting a resistor
from the IMON pin to VCC as shown in Figure 11. The
required value for RVCC can be determined by using
Equation 18:
R IMON ⋅ ( VCC – V IMONOFS – V IMONMAX )
R VCC = --------------------------------------------------------------------------------------------------------------------V IMONOFS
(EQ. 18)
where RIMON is the resistor from IMON to GND, VIMONOFS
is the desired offset voltage at VIMONMAX, and VIMONMAX
is the voltage at IMON at the maximum load current.
For example, if the maximum IMON voltage is 900mV at full
load and the required offset voltage is 50mV and RIMON is
10kΩ then RVCC should be 810kΩ. RIMON should be
connected to GND near the load to increase accuracy.
EXTERNAL CIRCUIT
VCC
ISL6336B
INTERNAL CIRCUIT
CIMON
Undervoltage Detection
The undervoltage threshold is set at 50% of the VID voltage.
When the output voltage at VSEN is below the undervoltage
threshold, VR_RDY gets pulled low. When the output voltage
comes back to 60% of the VID voltage, VR_RDY will return
back to high.
Regardless of the VR being enabled or not, the ISL6336B
overvoltage protection (OVP) circuit will be active after its
POR. The OVP thresholds are different under different
operation conditions. When VR is not enabled and before the
2nd soft-start, the OVP threshold is 1.275V. Once the
controller detects a valid VID input, the OVP trip point will be
changed to the VID voltage plus 175mV.
IMON
RIMON
The VR_RDY pin is an open-drain logic output to indicate
that the soft-start period is completed and the output voltage
is within the regulated range. VR_RDY is pulled low during
shutdown and releases high after a successful soft-start and
a fixed delay time, tD5 (see Figure 9). VR_RDY will be pulled
low when an undervoltage, overvoltage, or overcurrent
condition is detected, or if the controller is disabled by a
reset from EN_PWR, EN_VTT, POR, or VID OFF-code.
Overvoltage Protection
IAVG
RVCC
VR_RDY Signal
+
VIMON
-
Two actions are taken by the ISL6336B to protect the
microprocessor load when an overvoltage condition occurs.
NEAR LOAD GND
FIGURE 11. IMON RESISTOR DIVIDER
Fault Monitoring and Protection
The ISL6336B actively monitors output voltage and current to
detect fault conditions. Fault monitors trigger protective
measures to prevent damage to a microprocessor load. One
common power good indicator is provided for linking to external
system monitors. The schematic in Figure 12 outlines the
interaction between the fault monitors and the VR_RDY signal.
VR_RDY
UV
-
+
50%
DAC
VDIFF
At the inception of an overvoltage event, all PWM outputs are
commanded low instantly (in less than 20ns). This causes the
Intersil drivers to turn on the lower MOSFETs and pull the
output voltage down to avoid damaging the load. When the
voltage at VDIFF falls below the DAC plus 75mV, PWM
signals enter a high-impedance state. The Intersil drivers
respond to the high-impedance input by turning off both upper
and lower MOSFETs. If the overvoltage condition reoccurs,
the ISL6336B will again command the lower MOSFETs to turn
on. The ISL6336B will continue to protect the load in this
fashion as long as the overvoltage condition occurs.
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6336B is reset. Cycling the
voltage on EN_PWR, EN_VTT or VCC below the PORfalling threshold will reset the controller. Cycling the VID
codes will not reset the controller.
Overcurrent Protection
SOFT-START, FAULT
AND CONTROL LOGIC
+
-
OC
OC
+
OV
+
105µA
IAVG
1.11V
IMON
VID + 0.175V
FIGURE 12. VR_RDY AND PROTECTION CIRCUITRY
21
ISL6336B has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition by
limiting its peak current, while the combined phase currents
are protected on an instantaneous basis.
In instantaneous protection mode, the ISL6336B utilizes the
sensed average current IAVG to detect an overcurrent
condition. See “Channel-Current Balance” on page 15 for
more detail on how the average current is measured. The
average current is continually compared with a constant
105µA reference current, as shown in Figure 12. Once the
FN6696.2
August 31, 2010
ISL6336B
average current exceeds the reference current, a
comparator trips and causes the converter to shutdown.
The voltage at the IMON pin is used for average current
protection (compared to the instantaneous current protection
described above). The current out of the IMON pin is equal to
the sensed average current, IAVG. With a resistor from IMON
to GND, the voltage at IMON will be proportional to the
sensed average current and the resistor value. The ISL6336B
continually monitors the voltage at the IMON pin. If the voltage
at the IMON pin is higher than 1.11V, a comparator trips and
causes the converter to shutdown.
The voltage at the IMON pin may be delayed relative to the
sensed current, IAVG, due to the capacitor that is in parallel
with the IMON resistor to GND that is required in some
applications. This time constant can be >300µs. This lag can
cause the output voltage to remain high for a longer time
period before the OC comparator is tripped. This can lead to
higher duty cycles of the output voltage during overcurrent
hiccup mode. To avoid this the external current sense
resistors should be selected so that the instantaneous
overcurrent trip occurs at about the same sense current level
as the IMON trip. For example, the IMON resistor to GND
should be selected such that the voltage at IMON reaches
1.12V when IAVG reaches ~100µA. Another option is to
remove the capacitor that is in parallel with the IMON resistor
and add the required filter to the output of a IMON buffer.
At the beginning of overcurrent shutdown, the controller places
all PWM signals in a high-impedance state within 20ns
commanding the Intersil MOSFET driver ICs to turn off both
upper and lower MOSFETs. The system remains in this state
for 4096 switching cycles (programmed switching frequency). If
the controller is still enabled at the end of this wait period, it will
attempt a soft-start. If the fault remains, the trip-retry cycles will
continue indefinitely (as shown in Figure 13) until either
controller is disabled or the fault is cleared. Note that the energy
delivered during trip-retry cycling is much less than during fullload operation, so there is no thermal hazard during this kind of
operation.
OUTPUT CURRENT
0A
OUTPUT VOLTAGE
0V
2ms/DIV
For the individual channel overcurrent protection, the
ISL6336B continuously compares the sensed current signal
of each channel with the 129µA reference current. If one
channel current exceeds the reference current, ISL6336B
will pull the PWM signal of this channel low for the rest of the
switching cycle. This PWM signal can be turned on next
cycle if the sensed channel-current is less than the 129µA
reference current. The peak current limit of individual
channel will not trigger the converter to shutdown.
The overcurrent protection level for the above three OCP
modes can be adjusted by changing the value of current
sensing resistors. In addition, ISL6336B can also adjust the
average OCP threshold level by adjusting the value of the
resistor from IMON to GND. This provides additional safety
for the voltage regulator.
Equation 19 can be used to calculate the value of the
resistor RIMON based on the desired OCP level IAVG, OCP2.
1.11V
R IOUT = ------------------------------I AVG, OCP2
(EQ. 19)
Thermal Monitoring (VR_HOT)
There is one thermal signal to indicate the temperature
status of the voltage regulator: VR_HOT. VR_HOT is an
open-drain output, and an external pull-up resistor is
required. The VR_HOT signal is valid only after the controller
is enabled.
The VR_HOT signal can be used to inform the system that
the temperature of the voltage regulator is too high and the
CPU should reduce its power consumption. VR_HOT signal
may be tied to the CPU’s PROCHOT# signal.
The diagram of the thermal monitoring function block is shown
in Figure 14. One NTC resistor should be placed close to the
power stage of the voltage regulator to sense the operational
temperature, and one pull-up resistor is needed to form the
voltage divider for the TM pin. The NTC thermistor should be
placed next to the current sense element of a phase that will
remain active when PSI# is asserted low. As the temperature
of the power stage increases, the resistance of the NTC will
reduce, resulting in the reduced voltage at the TM pin.
Figure 15 shows the TM voltage over temperature for a typical
design with a recommended 6.8kΩ NTC
(P/N: NTHS0805N02N6801 from Vishay) and 1kΩ resistor
RTM1. We recommend using these resistors for accurate
temperature compensation.
There is a comparator with hysteresis to compare the TM pin
voltage to the fixed thresholds for VR_HOT. VR_HOT is set
to high when the TM voltage goes below 33.3% of VCC, and
is pulled to GND when the TM voltage goes back to above
39.1% of VCC. Figure 16 shows the operation of these
signals.
FIGURE 13. OVERCURRENT BEHAVIOR IN HICCUP MODE,
FSW = 500kHz
22
FN6696.2
August 31, 2010
ISL6336B
The NTC resistance at the set point T2 signal can be
calculated as:
VCC
R
TM1
VR_HOT
TM
R NTC ( t2 ) = 1.267xR NTC ( t3 )
(EQ. 21)
R NTC ( t1 ) = 1.644xR NTC ( t3 )
(EQ. 22)
With the NTC resistance value obtained from Equations 21
and 22, the temperature value t2 and t1 can be found from
the NTC datasheet.
Temperature Compensation
o
C
R
NTC
0.333VCC
FIGURE 14. BLOCK DIAGRAM OF THERMAL MONITORING
FUNCTION
In order to obtain the correct current information, there
should be a way to correct the temperature impact on the
current sense component. The ISL6336B provides two
methods: integrated temperature compensation and external
temperature compensation.
100
90
VTM/VCC (%)
80
70
60
Integrated Temperature Compensation
50
When the TCOMP voltage is equal to or greater than VCC/15,
ISL6336B will utilize the voltage at the TM and TCOMP pins to
compensate the temperature impact on the sensed current.
The block diagram of this function is shown in Figure 17.
40
30
20
0
ISL6336B supports inductor DCR sensing, or resistive
sensing techniques. The inductor DCR has a positive
temperature coefficient of about +0.385%/°C. Because the
voltage across inductor is sensed for output current
information, the sensed current has the same positive
temperature coefficient as the inductor DCR.
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 15. THE RATIO OF TM VOLTAGE TO NTC
TEMPERATURE WITH RECOMMENDED PARTS
VCC
ISen6
R TM1
TM
TM
o
c
I6
D/A
VCC
VR_FAN
NON-LINEAR
A/D
R NTC
0.391*VCC
0.333*VCC
CHANNEL
CURRENT
SENSE
I5
I4
I3
I2
I1
ISen5
ISen4
ISen3
ISen2
ISen1
ki
R TC1
VR_HOT
TEMPERATURE
t2
t3
Based on the NTC temperature characteristics and the
desired threshold of VR_HOT signal, the pull-up resistor
RTM1 of TM pin is given by Equation 20:
(EQ. 20)
RNTC(t3) is the NTC resistance at the VR_HOT threshold
temperature t3.
23
4-BIT
A/D
DROOP IOUT AND
OVERCURRENT
PROTECTION
R TC2
FIGURE 16. VR_HOT SIGNAL vs TM VOLTAGE
R TM1 = 2.75xR NTC ( t3 )
TCOMP
FIGURE 17. BLOCK DIAGRAM OF INTEGRATED
TEMPERATURE COMPENSATION
When the TM NTC is placed close to the current sense
component (inductor), the temperature of the NTC will track
the temperature of the current sense component. Therefore,
the TM voltage can be utilized to obtain temperature of the
current sense component.
FN6696.2
August 31, 2010
ISL6336B
Based on the VCC voltage, ISL6336B converts the TM pin
voltage to a 6-bit digital signal for temperature compensation.
With the non-linear A/D converter of ISL6336B, the TM digital
signal is linearly proportional to the NTC temperature. For
accurate temperature compensation, the ratio of the TM
voltage to the NTC temperature of the practical design should
be similar to that in Figure 15.
Depending on the location of the NTC and the air-flowing,
the NTC may be cooler or hotter than the current sense
component. The TCOMP pin voltage can be utilized to
correct the temperature difference between the NTC and the
current sense component. When a different NTC type or
different voltage divider is used for the TM function, the
TCOMP voltage can also be used to compensate for the
difference between the recommended TM voltage curve in
Figure 16 and that of the actual design. According to the
VCC voltage, ISL6336B converts the TCOMP pin voltage to
a 4-bit TCOMP digital signal as TCOMP factor N.
TCOMP factor N is an integer between 0 and 15. The
integrated temperature compensation function is disabled for
N = 0. For N = 4, the NTC temperature is equal to the
temperature of the current sense component. For N < 4, the
NTC is hotter than the current sense component. The NTC is
cooler than the current sense component for N > 4. When
N > 4, the larger TCOMP factor N, the larger the difference
between the NTC temperature and the temperature of the
current-sense component.
ISL6336B multiplexes the TCOMP factor N with the TM digital
signal to obtain the adjustment gain to compensate the
temperature impact on the sensed channel current. The
compensated channel current signal is used for droop and
overcurrent protection functions.
Design Procedure
1. Properly choose the voltage divider for TM pin to match
the TM voltage vs temperature curve with the
recommended curve in Figure 15.
2. Run the actual board under the full load and the desired
cooling condition.
3. After the board reaches the thermal steady state, record
the temperature (TCSC) of the current sense component
(e.g., inductor) and the voltage at TM and VCC pins.
4. Use Equation 23 to calculate the resistance of the TM
NTC, and find out the corresponding NTC temperature
TNTC from the NTC datasheet.
R NTC ( T
V TM xR
TM1
= ------------------------------)
V CC – V
NTC
TM
(EQ. 23)
5. Use Equation 24 to calculate the TCOMP factor N:
209x ( T CSC – T
)
NTC
N = -------------------------------------------------------- + 4
3xT NTC + 400
(EQ. 24)
7. Choose the pull-up resistor RTC1 (typical 10kΩ);
8. If N = 15, do not need the pull-down resistor RTC2,
otherwise obtain RTC2 by Equation 25:
NxR TC1
R TC2 = ----------------------15 – N
(EQ. 25)
9. Run the actual board under full load again with the proper
resistors to TCOMP pin.
10. Record the output voltage as V1 immediately after the
output voltage is stable with the full load; Record the
output voltage as V2 after the VR reaches the thermal
steady state.
11. If the output voltage increases over 2mV as the
temperature increases, i.e. V2 - V1 >2mV, reduce N and
redesign RTC2; if the output voltage decreases over 2mV
as the temperature increases, i.e. V1 - V2 >2mV,
increase N and redesign RTC2.
A design spreadsheet is available to speed aid calculations.
External Temperature Compensation
By pulling the TCOMP pin to GND, the integrated
temperature compensation function is disabled. In addition,
one external temperature compensation network, shown in
Figure 18, can be used to cancel the temperature impact on
the droop (i.e. load line).
COMP
ISL6336B
INTERNAL
CIRCUIT
FB
o
C
VDIFF
FIGURE 18. EXTERNAL TEMPERATURE COMPENSATION
The sensed current will flow out of the FB pin and develop the
droop voltage across the resistor (RFB) between FB and
VDIFF pins. If the RFB resistance reduces as the temperature
increases, the temperature impact on the droop can be
compensated. An NTC thermistor can be placed close to the
power stage and used to form RFB. Due to the non-linear
temperature characteristics of the NTC, a resistor network is
needed to make the equivalent resistance between FB and
VDIFF pin reverse proportional to the temperature.
The external temperature compensation network can only
compensate the temperature impact on the droop, while it
has no impact to the sensed current inside ISL6336B.
Therefore this network cannot compensate for the
temperature impact on the overcurrent protection function.
6. Choose an integral number close to the above result for
the TCOMP factor. If this factor is higher than 15, use
N = 15. If it is less than 1, use N = 1.
24
FN6696.2
August 31, 2010
ISL6336B
General Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multiphase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced in the
following. In addition to this guide, Intersil provides complete
reference designs that include schematics, bills of materials,
and example board layouts for all common microprocessor
applications.
Power Stages
The first step in designing a multiphase converter is to
determine the number of phases. This determination
depends heavily on the cost analysis which in turn depends
on system constraints that differ from one design to the next.
Principally, the designer will be concerned with whether
components can be mounted on both sides of the circuit
board; whether through-hole components are permitted; and
the total board space available for power-supply circuitry.
Generally speaking, the most economical solutions are
those in which each phase handles generally between 20A
and 25A. All surface-mount designs will tend toward the
lower end of this current range. If through-hole MOSFETs
and inductors can be used, higher per-phase currents are
possible. In cases where board space is the limiting
constraint, current can be pushed as high as 40A per phase,
but these designs require heat sinks and forced air to cool
the MOSFETs, inductors, and heat-dissipating surfaces.
MOSFETS
The choice of MOSFETs depends on the current each
MOSFET will be required to conduct; the switching
frequency; the capability of the MOSFETs to dissipate heat;
and the availability and nature of heat sinking and air flow.
LOWER MOSFET POWER CALCULATION
The calculation for heat dissipated in the lower MOSFET is
simple, since virtually all of the heat loss in the lower
MOSFET is due to current conducted through the channel
resistance (rDS(ON)). In Equation 26, IM is the maximum
continuous output current; IP-P is the peak-to-peak inductor
current (see Equation 1); d is the duty cycle (VOUT/VIN); and
L is the per-channel inductance.
I L, P-P2 ( 1 – d )
⎛ I M⎞ 2
P LOW, 1 = r DS ( ON ) ⎜ -----⎟ ( 1 – d ) + ----------------------------------12
⎝ N⎠
(EQ. 26)
An additional term can be added to Equation 26 to account
for additional loss accrued during the dead-time when
inductor current is flowing through the lower-MOSFET body
diode. This term is dependent on the diode forward voltage
at IM, VD(ON); the switching frequency, FS; and the length of
dead times, tD1 and tD2, at the beginning and the end of the
lower-MOSFET conduction interval respectively.
25
⎛I
⎞
I M I P-P⎞
(EQ. 27)
M I---------P LOW, 2 = V D ( ON ) F S ⎛ -----⎠ t d1 + ⎜ ----- – P-P-⎟ t d2
⎝ N- + ---------2 ⎠
2
⎝N
Thus, the total maximum power dissipated in each lower
MOSFET is approximated by the summation of PLOW,1 and
PLOW,2.
UPPER MOSFET POWER CALCULATION
In addition to rDS(ON) losses, a large portion of the upper
MOSFET losses are due to currents conducted across the
input voltage (VIN) during switching. Since a substantially
higher portion of the upper-MOSFET losses are dependent
on switching frequency, the power calculation is more
complex. Upper MOSFET losses can be divided into
separate components involving the upper-MOSFET
switching times; the lower-MOSFET body-diode reverse
recovery charge, Qrr; and the upper MOSFET rDS(ON)
conduction loss.
When the upper MOSFET turns off, the lower MOSFET does
not conduct any portion of the inductor current until the
voltage at the phase node falls below ground. Once the
lower MOSFET begins conducting, the current in the upper
MOSFET falls to zero as the current in the lower MOSFET
ramps up to assume the full inductor current. In Equation 28,
the required time for this commutation is t1 and the
approximated associated power loss is PUP,1.
I M I P-P⎞ ⎛ t 1 ⎞
P UP,1 ≈ V IN ⎛ ----- ⎜ ---- ⎟ F
⎝ N- + ---------2 ⎠ ⎝ 2⎠ S
(EQ. 28)
At turn-on, the upper MOSFET begins to conduct and this
transition occurs over a time t2. In Equation 29, the
approximate power loss is PUP,2.
⎛ I M I P-P⎞ ⎛ t 2 ⎞
P UP, 2 ≈ V IN ⎜ ----- – -----------⎟ ⎜ ---- ⎟ F S
2 ⎠⎝ 2⎠
⎝N
(EQ. 29)
A third component involves the lower MOSFET’s reverse
recovery charge, Qrr. Since the inductor current has fully
commutated to the upper MOSFET before the lower
MOSFET’s body diode can draw all of Qrr, it is conducted
through the upper MOSFET across VIN. The power dissipated
as a result is PUP,3 and is approximated in Equation 30:
P UP,3 = V IN Q rr F S
(EQ. 30)
Finally, the resistive part of the upper MOSFET’s is given in
Equation 31 as PUP,4.
2
2
I P-P
⎛ I M⎞
P UP,4 ≈ r DS ( ON ) ⎜ -----⎟ d + ----------- d
12
⎝ N⎠
(EQ. 31)
The total power dissipated by the upper MOSFET at full load
can now be approximated as the summation of the results
from Equations 28, 29, 30 and 31. Since the power
equations depend on MOSFET parameters, choosing the
correct MOSFETs can be an iterative process involving
repetitive solutions to the loss equations for different
MOSFETs and different switching frequencies.
FN6696.2
August 31, 2010
ISL6336B
Current Sensing Resistor
The desired loadline can be calculated by Equation 34:
The resistors connected to the ISEN+ pins determine the
gains in the load-line regulation loop and the channel-current
balance loop as well as setting the overcurrent trip point.
Select values for these resistors by the Equation 32.
V DROOP
R LL = -----------------------I FL
RX
I OCP
R ISEN = -------------------------- ------------–6 N
105 ×10
(EQ. 32)
where RISEN is the sense resistor connected to the ISEN+
pin, N is the active channel number, RX is the resistance of
the current sense element, either the DCR of the inductor or
RSENSE depending on the sensing method, and IOCP is the
desired overcurrent trip point. Typically, IOCP can be chosen
to be 1.2x the maximum load current of the specific
application.
With integrated temperature compensation, the sensed
current signal is independent on the operational temperature
of the power stage, i.e. the temperature effect on the current
sense element RX is cancelled by the integrated
temperature compensation function. RX in Equation 32,
should be the resistance of the current sense element at the
room temperature.
When the integrated temperature compensation function is
disabled by pulling the TCOMP pin to GND, the sensed
current will be dependent on the operational temperature of
the power stage, since the DC resistance of the current
sense element may be changed according to the operational
temperature. RX in Equation 32, should be the maximum DC
resistance of the current sense element at all the operational
temperature.
In certain circumstances, it may be necessary to adjust the
value of one or more ISEN resistors. When the components
of one or more channels are inhibited from effectively
dissipating their heat so that the affected channels run hotter
than desired, choose new, smaller values of RISEN for the
affected phases (see the section titled “Channel-Current
Balance” on page 15). Choose RISEN,2 in proportion to the
desired decrease in temperature rise in order to cause
proportionally less current to flow in the hotter phase.
ΔT
R ISEN ,2 = R ISEN ----------2
ΔT 1
(EQ. 33)
In Equation 33, make sure that ΔT2 is the desired temperature
rise above the ambient temperature, and ΔT1 is the measured
temperature rise above the ambient temperature. While a
single adjustment according to Equation 33 is usually
sufficient, it may occasionally be necessary to adjust RISEN
two or more times to achieve optimal thermal balance
between all channels.
Load-Line Regulation Resistor
(EQ. 34)
where IFL is the full load current of the specific application,
and VRDROOP is the desired voltage droop under the full
load condition.
Based on the desired loadline RLL, the loadline regulation
resistor can be calculated by Equation 35:
NR
R
ISEN LL
R FB = --------------------------------RX
(EQ. 35)
where N is the active channel number, RISEN is the sense
resistor connected to the ISEN+ pin, and RX is the
resistance of the current sense element, either the DCR of
the inductor or RSENSE depending on the sensing method.
If one or more of the current sense resistors are adjusted for
thermal balance, as in Equation 35, the load-line regulation
resistor should be selected based on the average value of
the current sensing resistors, as given in Equation 36:
R LL
R FB = ---------RX
∑ RISEN ( n )
(EQ. 36)
n
where RISEN(n) is the current sensing resistor connected to
the nth ISEN+ pin.
Compensation
The two opposing goals of compensating the voltage
regulator are stability and speed. Depending on whether the
regulator employs the optional load-line regulation as
described in Load-Line Regulation, there are two distinct
methods for achieving these goals.
COMPENSATING LOAD-LINE REGULATED
CONVERTER
The load-line regulated converter behaves in a similar
manner to a peak-current mode controller because the two
poles at the output-filter L-C resonant frequency split with
the introduction of current information into the control loop.
The final location of these poles is determined by the system
function, the gain of the current signal, and the value of the
compensation components, RC and CC.
Since the system poles and zero are affected by the values
of the components that are meant to compensate them, the
solution to the system equation becomes fairly complicated.
Fortunately there is a simple approximation that comes very
close to an optimal solution. Treating the system as though it
were a voltage-mode regulator by compensating the L-C
poles and the ESR zero of the voltage-mode approximation
yields a solution that is always stable with very close to ideal
transient performance.
The load-line regulation resistor is labelled RFB in Figure 6.
Its value depends on the desired loadline requirement of the
application.
26
FN6696.2
August 31, 2010
ISL6336B
The optional capacitor C2, is sometimes needed to bypass
noise away from the PWM comparator (see Figure 19). Keep
a position available for C2, and be prepared to install a high
frequency capacitor between 22pF and 150pF in case
excessive jitter is noted.
C2 (OPTIONAL)
ISL6336B
RC
CC
COMP
FB
+
RFB
VDROOP
VDIFF
FIGURE 19. COMPENSATION CONFIGURATION FOR
LOAD-LINE REGULATED ISL6336B CIRCUIT
The feedback resistor, RFB, has already been chosen as
outlined in “Load-Line Regulation Resistor” on page 26.
Select a target bandwidth for the compensated system, f0.
The target bandwidth must be large enough to ensure
adequate transient performance, but generally smaller than
1/3 of the per-channel switching frequency. The values of the
compensation components depend on the relationships of f0
to the L-C pole frequency and the ESR zero frequency. For
each of the three cases which follow, there are a separate
set of equations for the compensation components.
Once selected, the compensation values in Equation 37
ensure a stable converter with reasonable transient
performance. In most cases, transient performance can be
improved by making adjustments to RC. Slowly increase the
value of RC while observing the transient performance on an
oscilloscope until no further improvement is noted. Normally,
CC will not need adjustment. Keep the value of CC from
Equation 37 unless some performance issue is noted.
C1 and R1 can also be added to improve transient
performance per the type III compensation discussion in the
following.
COMPENSATION WITHOUT LOAD-LINE REGULATION
The non load-line regulated converter is accurately modeled
as a voltage-mode regulator with two poles at the L-C
resonant frequency and a zero at the ESR frequency. A
type III controller, as shown in Figure 20, provides the
necessary compensation.
C2
ISL6336B
Case 1:
RC
1
------------------- > f 0
2π LC
2πf 0 V P-P LC
R C = R FB ------------------------------------0.75V
FB
IN
R1
(EQ. 37)
0.75V IN
C C = -------------------------------------------------------------( 2π ) 2 f 02 V P-P R FB LC
Case 3:
1
f 0 > -----------------------------2πC ( ESR )
2π f 0 V P-P L
R C = R FB ----------------------------------------0.75 V IN ( ESR )
0.75V IN ( ESR ) C
C C = -----------------------------------------------2πV P-P R FB f 0 L
In Equation 37, L is the per-channel filter inductance divided
by the number of active channels; C is the sum total of all
output capacitors; ESR is the equivalent-series resistance of
the bulk output-filter capacitance; and VP-P is the
peak-to-peak sawtooth signal amplitude as described in the
“Electrical Specifications” table beginning on page 7.
27
RFB
VDIFF
1
1
------------------- ≤ f 0 < ----------------------------2πC ( ESR )
2π LC
V P-P ( 2π ) 2 f 02 LC
R C = R FB --------------------------------------------0.75 V IN
COMP
C1
0.75V IN
C C = ------------------------------------2πV P-P R FB f 0
Case 2:
CC
FIGURE 20. COMPENSATION CIRCUIT FOR ISL6336B BASED
CONVERTER WITHOUT LOAD-LINE
REGULATION
The first step is to choose the desired bandwidth, f0, of the
compensated system. Choose a frequency high enough to
ensure adequate transient performance but generally not
higher than 1/3 of the switching frequency. The type-III
compensator has an extra high-frequency pole, fHF. This
pole can be used for added noise rejection or to ensure
adequate attenuation at the error-amplifier high-order pole
and zero frequencies. A good general rule is to choose
fHF = 10f0, but it can be higher if desired. Choosing fHF to be
lower than 10f0 can cause problems with too much phase
shift below the system bandwidth.
In the solutions to the compensation equations, there is a
single degree of freedom. For the solutions presented in
Equation 38, RFB is selected arbitrarily. The remaining
FN6696.2
August 31, 2010
ISL6336B
compensation components are then selected according to
Equation 38.
response, the output voltage initially deviates by an amount,
as shown in Equation 39:
C ( ESR )
R 1 = R FB ----------------------------------------LC – C ( ESR )
di
ΔV ≈ ( ESL ) ⋅ ----- + ( ESR ) ⋅ ΔI
dt
(EQ. 39)
The filter capacitor must have sufficiently low ESL and ESR
so that ΔV < ΔVMAX.
LC – C ( ESR )
C 1 = ----------------------------------------R FB
0.75V IN
C 2 = ------------------------------------------------------------------( 2π ) 2 f 0 f HF LCR FB V P-P
(EQ. 38)
2
V P-P ⎛ 2π⎞ f 0 f HF LCR FB
⎝ ⎠
R C = -------------------------------------------------------------------⎛
⎞
0.75 V IN ⎝2πf HF LC – 1⎠
⎞
0.75V IN ⎛2πf
⎝ HF LC – 1⎠
C C = -------------------------------------------------------------------( 2π ) 2 f 0 f HF LCR FB V P-P
In Equation 38, L is the per-channel filter inductance divided
by the number of active channels; C is the sum total of all
output capacitors; ESR is the equivalent-series resistance of
the bulk output-filter capacitance; and VP-P is the
peak-to-peak sawtooth signal amplitude as described in the
“Electrical Specifications” table beginning on page 7.
Output Filter Design
The output inductors and the output capacitor bank together
form a low-pass filter responsible for smoothing the pulsating
voltage at the phase nodes. The output filter also must
provide the transient energy until the regulator can respond.
Because it has a low bandwidth compared to the switching
frequency, the output filter necessarily limits the system
transient response. The output capacitor must supply or sink
load current while the current in the output inductors
increases or decreases to meet the demand.
In high-speed converters, the output capacitor bank is
usually the most costly (and often the largest) part of the
circuit. Output filter design begins with minimizing the cost of
this part of the circuit. The critical load parameters in
choosing the output capacitors are the maximum size of the
load step, ΔI; the load-current slew rate, di/dt; and the
maximum allowable output-voltage deviation under transient
loading, ΔVMAX. Capacitors are characterized according to
their capacitance, ESR, and ESL (equivalent series
inductance).
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will
initially deviate by an amount approximated by the voltage
drop across the ESL. As the load current increases, the
voltage drop across the ESR increases linearly until the load
current reaches its final value. The capacitors selected must
have sufficiently low ESL and ESR so that the total output
voltage deviation is less than the allowable maximum.
Neglecting the contribution of inductor current and regulator
28
Most capacitor solutions rely on a mixture of high-frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of
the output-voltage ripple. As the bulk capacitors sink and
source the inductor ac ripple current (see “Interleaving” on
page 11 and Equation 2), a voltage develops across the
bulk-capacitor ESR equal to IC,P-P (ESR). Thus, once the
output capacitors are selected, the maximum allowable
ripple voltage, VP-P(MAX), determines the lower limit on the
inductance, as shown in Equation 40.
⎛V – N ⋅ V
⎞
OUT⎠ ⋅ V OUT
⎝ IN
L ≥ ( ESR ) ⋅ -------------------------------------------------------------------f S ⋅ V IN ⋅ V P-P( MAX )
(EQ. 40)
Since the capacitors are supplying a decreasing portion of
the load current while the regulator recovers from the
transient, the capacitor voltage becomes slightly depleted.
The output inductors must be capable of assuming the entire
load current before the output voltage decreases more than
ΔVMAX. This places an upper limit on inductance.
Equation 41 gives the upper limit on L for the cases when the
trailing edge of the current transient causes a greater
output-voltage deviation than the leading edge. Equation 42
addresses the leading edge. Normally, the trailing edge dictates
the selection of L because duty cycles are usually much less
than 50%. Nevertheless, both inequalities should be evaluated,
and L should be selected based on the lower of the two results.
In each equation, L is the per-channel inductance, C is the total
output capacitance, and N is the number of active channels.
2 ⋅ N ⋅ C ⋅ VO
L ≤ --------------------------------- ΔV MAX – ( ΔI ⋅ ( ESR ) )
( ΔI ) 2
1.25 ⋅ N ⋅ C
L ≤ ----------------------------- ΔV MAX – ( ΔI ⋅ ( ESR ) ) ⋅ ⎛ V IN – V O⎞
⎝
⎠
( ΔI ) 2
(EQ. 41)
(EQ. 42)
Switching Frequency
There are a number of variables to consider when choosing
the switching frequency, as there are considerable effects on
the upper-MOSFET loss calculation. These effects are
outlined in “MOSFETs” on page 25, and they establish the
upper limit for the switching frequency. The lower limit is
established by the requirement for fast transient response
FN6696.2
August 31, 2010
ISL6336B
Switching frequency is determined by the selection of the
frequency-setting resistor, RT (see “Typical Application - 5Phase Buck Converter with Thermal Compensation” on
page 5 and “Typical Application - 4-Phase Buck Converter
with Coupled Inductors” on page 6). Equation 3 is provided
to assist in selecting the correct value for RT.
Input Capacitor Selection
The input capacitors are responsible for sourcing the AC
component of the input current flowing into the upper
MOSFETs. Their RMS current capacity must be sufficient to
handle the AC component of the current drawn by the upper
MOSFETs that is related to duty cycle and the number of
active phases.
INPUT-CAPACITOR CURRENT (IRMS/IO)
0.3
0.2
Figures 22 and 23 provide the same input RMS current
information for three and four phase designs respectively.
Use the same approach to selecting the bulk capacitor type
and number, as previously described.
0.3
IL(P-P) = 0
IL(P-P) = 0.75 IO
0.2
0.4
0.6
DUTY CYCLE (VO/VIN)
0.8
1.0
FIGURE 21. NORMALIZED INPUT-CAPACITOR RMS CURRENT
vs DUTY CYCLE FOR 2-PHASE CONVERTER
0.3
IL(P-P) = 0.5 IO
IL(P-P) = 0.75 IO
0.1
0
0.2
0.4
0.6
DUTY CYCLE (VO/VIN)
0.8
1.0
FIGURE 23. NORMALIZED INPUT-CAPACITOR RMS CURRENT
vs DUTY CYCLE FOR 4-PHASE CONVERTER
IL(P-P) = 0.5 IO
0
IL(P-P) = 0
IL(P-P) = 0.25 IO
0.2
0
0.1
0
INPUT-CAPACITOR CURRENT (IRMS/IO)
For a 2-phase design, use Figure 21 to determine the
input-capacitor RMS current requirement given the duty
cycle, maximum sustained output current (IO), and the ratio
of the per-phase peak-to-peak inductor current (IL(P-P)) to
IO. Select a bulk capacitor with a ripple current rating which
will minimize the total number of input capacitors required to
support the RMS current calculated. The voltage rating of
the capacitors should also be at least 1.25x greater than the
maximum input voltage.
INPUT-CAPACITOR CURRENT (IRMS/IO)
and small output-voltage ripple as outlined in “Output Filter
Design” on page 28. Choose the lowest switching frequency
that allows the regulator to meet the transient-response
requirements.
IL(P-P) = 0
IL(P-P) = 0.5 IO
IL(P-P) = 0.25 IO
IL(P-P) = 0.75 IO
Low capacitance, high-frequency ceramic capacitors are
needed in addition to the bulk capacitors to suppress leading
and falling edge voltage spikes. They result from the high
current slew rates produced by the upper MOSFETs turning
on and off. Select low ESL ceramic capacitors and place one
as close as possible to each upper MOSFET drain to
minimize board parasitic impedances and maximize
suppression. More than one of these low ESL capacitors
may be needed.
MULTI-PHASE RMS IMPROVEMENT
0.2
0.1
0
0
0.2
0.4
0.6
DUTY CYCLE (VO/VIN)
0.8
1.0
FIGURE 22. NORMALIZED INPUT-CAPACITOR RMS CURRENT
vs DUTY CYCLE FOR 3-PHASE CONVERTER
29
Figure 24 is provided as a reference to demonstrate the
dramatic reductions in input-capacitor RMS current upon the
implementation of the multiphase topology. For example,
compare the input RMS current requirements of a 2-phase
converter versus that of a single phase. Assume both
converters have a duty cycle of 0.25, maximum sustained
output current of 40A, and a ratio of IL,P-P to IO of 0.5. The
single phase converter would require 17.3ARMS current
capacity while the two-phase converter would only require
10.9ARMS. The advantages become even more pronounced
when output current is increased and additional phases are
added to keep the component cost down relative to the
single phase approach.
FN6696.2
August 31, 2010
ISL6336B
The ISL6336B can be placed off to one side or centered
relative to the individual phase switching components.
Routing of sense lines and PWM signals will guide final
placement. Critical small signal components to place close
to the controller include the ISEN resistors, RT resistor,
feedback resistor, and compensation components.
INPUT-CAPACITOR CURRENT (IRMS/IO)
0.6
0.4
Bypass capacitors for the ISL6336B and ISL66xx driver bias
supplies must be placed next to their respective pins. Trace
parasitic impedances will reduce their effectiveness.
0.2
IL(P-P) = 0
IL(P-P) = 0.5 IO
IL(P-P) = 0.75 IO
0
0
0.2
Plane Allocation and Routing
0.4
0.6
DUTY CYCLE (VO/VIN)
0.8
1.0
FIGURE 24. NORMALIZED INPUT-CAPACITOR RMS
CURRENT vs DUTY CYCLE FOR SINGLE-PHASE
CONVERTER
Layout Considerations
The following layout strategies are intended to minimize the
impact of board parasitic impedances on converter
performance and to optimize the heat-dissipating capabilities
of the printed-circuit board. The following sections highlight
some important practices which should not be overlooked
during the layout process.
Component Placement
Within the allotted implementation area, orient the switching
components first. The switching components are the most
critical because they carry large amounts of energy and tend
to generate high levels of noise. Switching component
placement should take into account power dissipation. Align
the output inductors and MOSFETs such that spaces
between the components are minimized while creating the
PHASE plane. Place the Intersil MOSFET driver IC as close
as possible to the MOSFETs they control to reduce the
parasitic impedances due to trace length between critical
driver input and output signals. If possible, duplicate the
same placement of these components for each phase.
Dedicate one solid layer, usually a middle layer, for a ground
plane. Make all critical component ground connections with
vias to this plane. Dedicate one additional layer for power
planes; breaking the plane up into smaller islands of
common voltage. Use the remaining layers for signal wiring.
Route phase planes of copper filled polygons on the top and
bottom once the switching component placement is set. Size
the trace width between the driver gate pins and the
MOSFET gates to carry 4A of current. When routing
components in the switching path, use short wide traces to
reduce the associated parasitic impedances.
Voltage Regulator (VR) Design Materials
Voltage tolerance band calculation (TOB) worksheets for VR
output regulation and IMON tolerance have been developed
using the Root-Sum-Squared (RSS) method with 3-sigma
distribution data of the related components and parameters.
Note that the “Electrical Specifications” table beginning on
page 7 specifies no less than 6-sigma distribution data and
is not suitable for RSS TOB calculations. Intersil has
developed a set of worksheets to help support VR designs
and layout. Contact Intersil’s local office or field support for
the latest information.
Next, place the input and output capacitors. Position one high
frequency ceramic input capacitor next to each upper
MOSFET drain. Place the bulk input capacitors as close to the
upper MOSFET drains as dictated by the component size and
dimensions. Long distances between input capacitors and
MOSFET drains result in too much trace inductance and a
reduction in capacitor performance. Locate the output
capacitors between the inductors and the load, while keeping
them in close proximity to the microprocessor socket.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
30
FN6696.2
August 31, 2010
ISL6336B
Package Outline Drawing
L48.7x7
48 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 4, 10/06
4X 5.5
7.00
A
44X 0.50
B
37
6
PIN 1
INDEX AREA
6
PIN #1 INDEX AREA
48
1
7.00
36
4. 30 ± 0 . 15
12
25
(4X)
0.15
13
24
0.10 M C A B
48X 0 . 40± 0 . 1
TOP VIEW
4 0.23 +0.07 / -0.05
BOTTOM VIEW
SEE DETAIL "X"
( 6 . 80 TYP )
(
0.10 C
BASE PLANE
0 . 90 ± 0 . 1
4 . 30 )
C
SEATING PLANE
0.08 C
SIDE VIEW
( 44X 0 . 5 )
C
0 . 2 REF
5
( 48X 0 . 23 )
( 48X 0 . 60 )
0 . 00 MIN.
0 . 05 MAX.
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
31
FN6696.2
August 31, 2010