AWU6615 HELP3ETM Dual-band Cell & PCS WCDMA 3.4 V Linear Power Amplifier Module Data Sheet - Rev 2.2 FEATURES • InGaP HBT Technology • High Efficiency: • 39 % @ POUT = +28.7 dBm • 22 % @ POUT = +16.6 dBm • 9 % @ POUT = +8 dBm AW U 661 • Low Quiescent Current: 4.5 mA • Internal Voltage Regulation 5 • Built-in Directional Coupler • Common VMODE Control Line • Simplified VCC Bus PCB routing • Reduced External Component Count • Low Profile Surface Mount Package: 1 mm • RoHS Compliant Package, 260 oC MSL-3 M47 Package 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module APPLICATIONS • Cell & PCS Dual-band Wireless Handsets and Data Devices for HSDPA/HSPA networks. PRODUCT DESCRIPTION AWU6615 addresses the demand for increased integration in dual-band handsets for WCDMA networks. The small footprint 3 mm x 5 mm x 1 mm surface- mount RoHS compliant package contains independent RF PA paths to ensure optimal performance in both frequency bands, while achieving a 25% PCB space savings compared with solutions requiring two single-band PAs. The package pinout was chosen to enable handset manufacturers to easily route bias to both power amplifiers and simplify control with common mode pins. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. The AWU6615 is part of ANADIGICS’ High-Efficiency-at-Low-Power (HELP™) family of WCDMA power amplifiers, which deliver low quiescent currents and significantly greater efficiency without the need of an external DC-DC converter. Through selectable bias modes, the AWU6615 achieves optimal efficiency, specifically at low- and mid-range power levels where the PA typically operates, thereby dramatically increasing handset talk-time. Its built-in voltage regulator eliminates the need for external switches. This PA has built-in directional couplers for each band, with a common coupler output port CPL_OUT. These couplers provide high directivity and 23 dB Coupling. The 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 Ω system. 07/2011 VEN_CELL 1 14 GND Bias Control Voltage Regulation RFIN_CELL CPL 2 13 RFOUT_CELL VMODE1 3 12 VCC VBATT 4 11 VCCA VMODE2 5 10 CPLOUT RFIN_PCS 6 VEN_PCS 7 CPL Bias Control Voltage Regulation GND at Slug (pad) Figure 1: Block Diagram 9 GND 8 RFOUT_PCS AWU6615 VMODE1 CPLOUT VMODE2 Figure 2: Pinout Table 1: Pin Description PIN NAME DESCRIPTION 1 VEN_CELL Enable Voltage for Cell Band 2 RFIN_CELL RF Input for Cell Band 3 VMODE1 Mode Control Voltage for Cell and PCS Bands 4 VBATT Battery Voltage 5 VMODE2 Mode Control Voltage for Cell 6 RFIN_PCS RF Input for PCS Band 7 VEN_PCS Enable Voltage for PCS Band 8 RFOUT_PCS 9 GND 10 CPLOUT 11 VCCA 12 VCC 13 14 2 RF Output for PCS Band Ground Coupler Output Port Battery Voltage A Supply Voltage RFOUT_CELL RF Output for Cell Band GND Ground Data Sheet - Rev 2.2 07/2011 AWU6615 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VBATT, VCC, VCCA) 0 +5 V Mode Control Voltage (VMODE1, VMODE2) 0 +3.5 V Enable Voltage (VEN_CELL, VEN_PCS) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 8C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 824 1850 - 849 1910 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +1.35 0 +1.8 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE0, VMODE1) +1.35 0 +1.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power, Band 5, UMTS R99 WCDMA, HPM HSPA (MPR = 0 dB), HPM R99 WCDMA, MPM HSPA (MPR = 0 dB), MPM R99 WCDMA, LPM HSPA (MPR = 0 dB), LPM 28.2(1) 27.2(1) 16.1(1) 15.1(1) 7.5(1) 6.5(1) 28.7 27.7 16.6 15.6 8.0 7.0 - RF Output Power, Band 2, UMTS R99 WCDMA, HPM HSPA (MPR = 0 dB), HPM R99 WCDMA, MPM HSPA (MPR = 0 dB), MPM R99 WCDMA, LPM HSPA (MPR = 0 dB), LPM 28.3(1) 27.3(1) 16.5(1) 15.5(1) 8.0(1) 7.0(1) 28.8 27.8 17.0 16.0 8.5 7.5 - -30 - +90 Case Temperature (TC) COMMENTS Cellular (Band 5) PCS (Band 2) dBm 3GPP TS 34.121-1, REL8 Table C.11.1.3, Subtest 1 dBm 3GPP TS 34.121-1, REL8 Table C.11.1.3, Subtest 1 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1)For operation at VCC = +3.2 V, TC = +90 8C POUT is derated by 0.5 dB. Data Sheet - Rev 2.2 07/2011 3 AWU6615 Table 4: Electrical Specifications - Cellular Band (Band 5) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN_CELL = +1.8 V, 50 Ω system, R99 uplink waveform) MIN TYP MAX UNIT Gain 25.5 14.5 9 27.5 17 11.5 30 20 14 dB +28.7 dBm 0 V +16.6 dBm 1.8 V +8 dBm 1.8 V 0V 0V 1.8 V ACLR1 @ 5 MHz Offset (1) - -42 -42 -41 -37 -37 -37 dBc +28.7 dBm 0 V +16.6 dBm 1.8 V +8 dBm 1.8 V 0V 0V 1.8 V ACLR2 @ 10 MHz Offset (1) - -58 -55 -54 -48 -48 -48 dBc +28.7 dBm 0 V +16.6 dBm 1.8 V +8 dBm 1.8 V 0V 0V 1.8 V Power-Added Efficiency (1) 35 18 6 39 22 9 - % +28.7 dBm 0 V +16.6 dBm 1.8 V +8 dBm 1.8 V 0V 0V 1.8 V Quiescent Current (Icq) - 4 6.5 mA through VCC pin, VMODE1 = +1.8 V, VMODE2 =+1.8 V Mode Control Current - <0.1 0.15 mA through VMODE pins, VMODE1= +1.8 V Battery Current - 1.5 2.5 mA through VBATT pin, VMODE1 = +1.8 V, VMODE2 = +1.8 V Enable Current - 0.15 0.25 mA through VEN_CELL pin, VMODE = 1.8 V Noise in Receive Band - -133 - dBm/Hz Harmonics 2fo 3fo, 4fo - -40 -50 -30 -38 dBc Input Impedance - - 2:1 VSWR Coupling Factor - 23 - dB Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dBc 8:1 - - VSWR Notes: (1) Efficiency and ACLR measured at 836.5 MHz. 4 COMMENTS PARAMETER Data Sheet - Rev 2.2 07/2011 POUT VMODE1 VMODE2 869 MHz to 894 MHz POUT < +28.7 dBm POUT < +28.7 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over full operating conditions AWU6615 Table 5: Electrical Specifications - PCS Band (Band 2) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN_PCS = +1.8 V, 50 Ω system, R99 uplink waveform) COMMENTS MIN TYP MAX UNIT 25 12 8 27 15 11 30.5 18 13.5 dB +28.8 dBm +17 dBm +8.5 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V ACLR1 @ 5 MHz Offset - -41 -40 -42 -37 -37 -37 dBc +28.8 dBm +17 dBm +8.5 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V ACLR2 @ 5 MHz Offset - -52 -53 -56 -48 -48 -48 dBc +28.8 dBm +17 dBm +8.5 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V 35 18 6 39 21 8.5 - % +28.8 dBm +17 dBm +8.5 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V Quiescent Current (Icq) - 5 7 mA through VCC Pin, VMODE1 = +1.8 V, VMODE2 =+1.8 V Mode Control Current - 0.1 0.15 mA through VMODE pins, VMODE1= +1.8 V Battery Current - 1.5 2.5 mA through VBATT pin, VMODE1 = +1.8 V, VMODE2 = +1.8 V Enable Current - 0.15 0.25 mA through VEN_CELL pin, VMODE1 = VMODE2 = 1.8 V HBT Leakage Current (VCC) - <1 5 A VBATT = +4.2 V, VCC = +4.2 V, VEN_CELL = 0 V, VMODE1 = 0 V, VMODE2 = 0 V Total Decoder Current on VBATT (Shutdown Mode) - 12 22 A VBATT = +4.2 V, VCC = +4.2 V, VEN = 0 V, VMODE1 = VMODE2 = 0 V Noise in Receive Band - -134 - Harmonics 2fo 3fo, 4fo - -42 -50 -30 -38 dBc Input Impedance - - 2:1 VSWR Coupling Factor - 22.5 - dB PARAMETER Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure POUT VMODE1 VMODE2 dBm/Hz 1930 MHz to 1990 MHz POUT < +28.8 dBm - - -65 dBc POUT < +28.8 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Applies over full operating conditions Notes: 1.Efficiency and ACLR measured at 1880 MHz. Data Sheet - Rev 2.2 07/2011 5 AWU6615 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VENABLE and VMODE voltages. Bias Modes, Medium Bias Mode The power amplifier may be placed in Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE1, and VMODE2 pins. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control APPLICATION POUT LEVELS BIAS MODE VEN VMODE1 VMODE2 VCC VBATT WCDMA - low power (Low Bias Mode) < +8 dBm Low +1.8 V +1.8 +1.8 V 3.2 - 4.2 V > 3.2 V WCDMA - med power (Medium Bias Mode) > +8 dBm < +16.5 dBm Low +1.8 V +1.8 V 0V 3.2 - 4.2 V > 3.2 V WCDMA - high power (High Bias Mode) > +16.5 dBm High +1.8 V 0V 0V 3.2 - 4.2 V > 3.2 V - Shutdown 0V 0V 0V 3.2 - 4.2 V > 3.2 V Shutdown VEN_CELL 1 14 Bias Control Voltage Regulation RFIN_CELL (1) CPL 2 13 68 pF 12 3 VMODE1 RFOUT_CELL VCC 1000 pF VBATT 2.2 F VMODE2 RFIN_PCS (1) VEN_PCS 68pF 4 11 1000 pF 5 10 CPL 6 7 Bias Control Voltage Regulation GND at Slug (pad) Figure 3: Application Circuit Note: (1) Add blocking cap if DC voltage is present on input pin. 6 Data Sheet - Rev 2.2 07/2011 2.2 F CPLOUT 9 8 33 pF RFOUT_PCS AWU6615 PACKAGE OUTLINE Figure 4: Package Outline - 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Pin 1 Identifier Date Code YY= Year WW= Work Week 6615R LLLLNN CC YYWW Part Number Lot Number Country Code Figure 5: Branding Specification Data Sheet - Rev 2.2 07/2011 7 AWU6615 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWU6615RM47Q7 -30 °C to +90 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel AWU6615RM47P9 -30 °C to +90 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Partial Tape and Reel ANADIGICS 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.1 07/2011