AWT6221R HELP3TM Dual-band Cellular/PCS UMTS 3.4 V HSPA Linear Power Amplifier Module DATA SHEET - Rev 2.3 FEATURES • InGaP HBT Technology • High Efficiency: 19 % @ +16 dBm POUT 40 % @ maximum POUT • Low Quiescent Current: 8 mA AW T 622 • Internal Voltage Regulation • Common VMODE Control Line 1R • Simplified VCC Bus PCB routing • Reduced External Component Count • Low Profile Surface Mount Package: 1 mm • HSDPA Compliant • RoHS Compliant Package, 250 oC MSL-3 APPLICATIONS M28 Package 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module • WCDMA/HSPA Dual-Band Cell/PCS Wireless Handsets and Data Devices PRODUCT DESCRIPTION The AWT6221R addresses the demand for increased integration in dual-band handsets for North American UMTS network deployments. The small footprint 3 mm x 5 mm x 1 mm surface mount RoHS compliant package contains independent RF PA paths to ensure optimal performance in both frequency bands, while achieving a 25% PCB space savings compared with solutions requiring two single-band PAs. The package pinout was chosen to enable handset manufacturers to easily route VCC to both power amplifiers and simplify control with a common V MODE pin. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. The AWT6221R incorporates ANADIGICS’ HELP3™ technology to provide low power consumption without the need for an external voltage regulator. Two operating modes provide optimum efficiency at high and medium/low power output levels, thereby dramatically increasing handset talk-time and standby-time. Its built-in voltage regulator eliminates the need for external voltage regulation and load switches. The 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 Ω system. Figure 1: Block Diagram 11/2008 AWT6221R Figure 2: Pinout Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VEN_CELL Enable Voltage for Cell Band 2 RFIN_CELL RF Input for Cell Band 3 VMODE1 Mode Control Voltage 1 4 VBATT Battery Voltage 5 VMODE2 (N/C) No Connection 6 RFIN_PCS RF Input for PCS Band 7 VEN_PCS Enable Voltage for PCS Band 8 RFOUT_PCS 9 GND Ground 10 GND Ground 11 VCCA Supply Voltage A 12 VCC 13 RFOUT_CELL 14 GND RF Output for PCS Band Supply Voltage RF Output for Cell Band Ground Data Sheet - Rev 2.3 11/2008 AWT6221R ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VBATT, VCC, VCCA) 0 +5 V Mode Control Voltage (VMODE1) 0 +3.5 V Enable Voltage (VEN_CELL, VEN_PCS) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 824 1850 - 849 1910 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +2.2 0 +2.4 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE1) +2.2 0 +2.4 - +3.1 +0.5 V Low Bias Mode High Bias Mode Cellular RF Output Power (POUT) R99 WCDMA, HPM HSPA (MPR=0), HPM R99 WCDMA, LPM HSPA (MPR=0), LPM 28.5 (1) 27.5 (1) 15.5 (1) 14.5 (1) 29 28 16 15 29 28 16 15 dBm 3GPP TS 34.121-1, Rel 7 Table C.11.1.3 PCS RF Output Power (POUT) R99 WCDMA, HPM HSPA (MPR=0), HPM R99 WCDMA, LPM HSPA (MPR=0), LPM 29 (1) 28 (1) 15.5 (1) 14.5 (1) 29.5 28.5 16 15 29.5 28.5 16 15 dBm 3GPP TS 34.121-1, Rel 7 Table C.11.1.3 -20 - +90 °C Case Temperature (TC) COMMENTS Cellular PCS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1)For operations at VCC = +3.2 V, POUT is derated by 0.5 dB (all operating modes). Data Sheet - Rev 2.3 11/2008 3 AWT6221R Table 4: Electrical Specifications - Cellular Band (TC = +25 °C, VBATT = VCC = +3.4 V, VENABLE = +2.4 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 24.5 13.5 27 15.5 29.0 18.0 ACLR1 at 5 MHz offset (1) - -41 -44 ACLR2 at 10 MHz offset - COMMENTS POUT VMODE1 dB +29 dBm +16 dBm 0V 2.4 V -37.5 -38 dBc +29 dBm +16 dBm 0V 2.4 V -60 -57 -48 -48 dBc +29 dBm +16 dBm 0V 2.4 V 38 18 42 22 - % +29 dBm +16 dBm 0V 2.4 V Quiescent Current (Icq) - 8 13 mA VMODE1 = +2.4 V Mode Control Current - 0.35 0.8 mA through VMODE1 pin, VMODE = +2.4 V Enable Current - 0.5 0.8 mA through VENABLE pin BATT Current - 2.5 5 mA through VBATT pin, VMODE1 = +2.4 V Leakage Current - <1 5 µA VBATT = +4.2 V, VCC = +4.2 V, VENABLE = 0 V, VMODE1 = 0 V Noise in Receive Band (2) - -135 -141 -133 -138 dBm/Hz Harmonics 2fo 3fo, 4fo - -44 -50 -35 -35 dBc Input Impedance - - 2:1 VSWR Spurious Output Level (all spurious outputs) - - -70 dBc 8:1 - - VSWR Power-Added Efficiency (1) Load mismatch stress with no permanent degradation or failure POUT = +29 dBm, VMODE1 = 0 V, V POUT = +16 dBm, VMODE1 = +2.4 V POUT < +29 dBm See Note 3 Applies over full operating range Notes: (1) ACLR and Efficiency measured at 836.5 MHz. (2) 869 MHz to 894 MHz. (3) POUT < +29 dBm, In-band load VSWR < 5:1, Out-of-band load VSWR < 10:1. Applies over all operating conditions. 4 Data Sheet - Rev 2.3 11/2008 AWT6221R Table 5: Electrical Specifications - PCS Band (TC = +25 °C, VBATT = VCC = +3.4 V, VENABLE = +2.4 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 24.5 12 26.5 14.0 29.0 17.0 ACLR1 at 5 MHz offset (1) - -41 -42 ACLR2 at 10 MHz offset - COMMENTS POUT VMODE1 dB +29.5 dBm +16 dBm 0V 2.4 V -37.5 -38 dBc +29.5 dBm +16 dBm 0V 2.4 V -55 -54 -48 -48 dBc +29.5 dBm +16 dBm 0V 2.4 V 35 15 38.5 17.5 - % +29.5 dBm +16 dBm 0V 2.4 V Quiescent Current (Icq) Low Bias Mode - 8 13 mA VMODE1 = +2.4 V Mode Control Current - 0.35 0.8 mA through VMODE pins, VMODE = +2.4 V Enable Current - 0.35 0.8 mA through VENABLE pin BATT Current - 2.5 5 mA through VBATT pin, VMODE1 = 2.4 V Leakage Current - <1 5 µA VBATT = +4.2 V, VCC = +4.2 V, VENABLE = 0 V, VMODE1 = 0 V - -137 140 -135 -138 dBm/Hz Harmonics 2fo 3fo, 4fo - -42 -46 -35 -35 dBc Input Impedance - - 2:1 VSWR Power-Added Efficiency (1) Noise in Receive Band (2) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure POUT = +29.5 dBm, VMODE1 = 0 V POUT = +16 dBm, VMODE1 = 2.4 V - - -70 dBc POUT < +29.5 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Applies over full operating range Notes: (1) ACLR and Efficiency measured at 1880 MHz. (2) 1930 MHz to 1990 MHz. Data Sheet - Rev 2.3 11/2008 5 AWT6221R APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com The Bias Control table lists the recommended modes of operation for various applications. VMODE2 is not necessary for this PA. Shutdown Mode Two operating modes are available to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 16 dBm. At around 16 dBm output power, the PA should be “Mode Switched” to Medium/Low power mode for lowest quiescent current consumption. The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VENABLE and VMODE1 voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to VMODE1. Table 6: Bias Control POUT LEVELS BIAS MODE VENABLE VMODE1 VCC VBATT UMTS - low power < +16 dBm Low +2.4 V +2.4 V 3.2 - 4.2 V > 3.2 V UMTS - high power > +16 dBm High +2.4 V 0V 3.2 - 4.2 V > 3.2 V Optional lower VCC in low power mode < +7 dBm Low +2.4 V +2.4 V 1.5 V > 3.2 V - Shutdown 0V 0V 3.2 - 4.2 V > 3.2 V APPLICATION Shutdown Figure 3: Application Circuit 6 Data Sheet - Rev 2.3 11/2008 AWT6221R PACKAGE OUTLINE Figure 4: Package Outline - 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Figure 5: Branding Specification Data Sheet - Rev 2.3 11/2008 7 AWT6221R ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWT6221RM28Q7 -20 °C to +85 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel AWT6221RM28P9 -20 °C to +85 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Partial Tape and Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.3 11/2008