11AA02E48 2K UNI/O® Serial EEPROM with EUI-48™ Node Identity DEVICE SELECTION TABLE Part Number Density (bits) 11AA02E48 2K Organization VCC Range 256 x 8 Page Size (Bytes) Temp. Ranges Packages 16 I SN, TT 1.8-5.5V Features: • Pre-programmed Globally Unique, 48-bit Node Address • Compatible with EUI-48™ and EUI-64™ • Single I/O, UNI/O® Serial Interface Bus • Low-Power CMOS Technology - 1 mA active current, typical - 1 µA standby current (max.) • 256 x 8 Bit Organization • Schmitt Trigger Inputs for Noise Suppression • Output Slope Control to Eliminate Ground Bounce • 100 kbps Max. Bit Rate – Equivalent to 100 kHz Clock Frequency • Self-Timed Write Cycle (including Auto-Erase) • Page-Write Buffer for up to 16 Bytes • STATUS Register for Added Control: - Write enable latch bit - Write-In-Progress bit • Block Write Protection - Protect none, 1/4, 1/2 or all of array • Built-in Write Protection - Power-on/off data protection circuitry - Write enable latch • High Reliability - Endurance: 1,000,000 erase/write cycles - Data retention: > 200 years - ESD protection: > 4,000V • 3-lead SOT-23 and 8-lead SOIC Packages • Pb-Free and RoHS Compliant • Available Temperature Ranges: - Industrial (I): -40°C to +85°C Description: The Microchip Technology Inc. 11AA02E48 device is a 2 Kbit Serial Electrically Erasable PROM. The device is organized in blocks of x8-bit memory and support the patented* single I/O UNI/O® serial bus. By using Manchester encoding techniques, the clock and data are combined into a single, serial bit stream (SCIO), where the clock signal is extracted by the receiver to correctly decode the timing and value of each bit. Low-voltage design permits operation down to 1.8V, with standby and active currents of only 1 uA and 1 mA, respectively. The 11AA02E48 is available in standard 8-lead SOIC and 3-lead SOT-23 packages. Package Types (not to scale) SOIC SOT23 (SN) (TT) 2 VCC VSS 3 1 SCIO Note: NC NC 1 2 8 7 VCC NC 3 6 NC VSS 4 5 SCIO NC This document is supplemented by the “11AAXXX/11LCXXX Family Data Sheet” (DS22067). See Section 2.0 “Functional Description”. Pin Function Table Name SCIO VSS VCC Function Serial Clock, Data Input/Output Ground Supply Voltage © 2008 Microchip Technology Inc. * Microchip’s UNI/O® Bus products are covered by the following patent issued in the U.S.A.: 7,376,020. Preliminary DS22122A-page 1 11AA02E48 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (†) VCC .............................................................................................................................................................................6.5V SCIO w.r.t. VSS .................................................................................................................................... -0.6V to VCC+1.0V Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias .................................................................................................................-40°C to 85°C ESD protection on all pins ..........................................................................................................................................4 kV † NOTICE: Stresses above those listed under ‘Absolute Maximum Ratings’ may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended period of time may affect device reliability. TABLE 1-1: DC CHARACTERISTICS DC CHARACTERISTICS Param. No. Sym. D1 VIH D2 VIL D3 VHYS D4 Characteristic Electrical Characteristics: Industrial (I): VCC = 2.5V to 5.5V VCC = 1.8V to 2.5V TA = -40°C to +85°C TA = -20°C to +85°C Min. Max. Units Test Conditions High-level Input Voltage 0.7*VCC VCC+1 V Low-level Input Voltage -0.3 -0.3 0.3*VCC 0.2*VCC V V VCC ≥ 2.5V VCC < 2.5V Hysteresis of Schmitt Trigger inputs (SCIO) 0.05*Vcc — V VCC ≥ 2.5V (Note 1) VOH High-level Output Voltage VCC -0.5 VCC -0.5 — — V V IOH = -300 μA, VCC = 5.5V IOH = -200 μA, Vcc = 2.5V D5 VOL Low-level Output Voltage — — 0.4 0.4 V V IOI = 300 μA, VCC = 5.5V IOI = 200 μA, Vcc = 2.5V D6 IO Output Current Limit (Note 2) — — ±4 ±3 mA mA VCC = 5.5V (Note 1) Vcc = 2.5V (Note 1) D7 ILI Input Leakage Current (SCIO) — ±1 μA VIN = VSS or VCC D8 CINT Internal Capacitance (all inputs and outputs) — 7 pF TA = 25°C, FCLK = 1 MHz, VCC = 5.0V (Note 1) D9 ICC Read Read Operating Current — — 3 1 mA mA VCC=5.5V, FBUS=100 kHz, CB=100 pF VCC=2.5V, FBUS=100 kHz, CB=100 pF D10 ICC Write Write Operating Current — — 5 3 mA mA VCC = 5.5V VCC = 2.5V D11 Iccs Standby Current — 1 μA VCC = 5.5V, TA = 85°C D12 ICCI Idle Mode Current — 50 μA VCC = 5.5V Note 1: 2: This parameter is periodically sampled and not 100% tested. The SCIO output driver impedance will vary to ensure IO is not exceeded. DS22122A-page 2 Preliminary © 2008 Microchip Technology Inc. 11AA02E48 TABLE 1-2: AC CHARACTERISTICS Electrical Characteristics: Industrial (I): VCC = 2.5V to 5.5V VCC = 1.8V to 2.5V AC CHARACTERISTICS Param. No. Sym. 1 FBUS 2 TE 3 TIJIT Characteristic Min. Max. Units Serial Bus Frequency 10 100 kHz Bit Period 10 100 µs — Input Edge Jitter Tolerance — ±0.08 UI (Note 3) — ±0.75 FDRIFT Serial Bus Frequency Drift Rate Tolerance 4 TA = -40°C to +85°C TA = -20°C to +85°C Test Conditions — % per byte — 5 FDEV Serial Bus Frequency Drift Limit — ±5 6 TOJIT Output Edge Jitter — ±0.25 UI (Note 3) 7 TR SCIO Input Rise Time (Note 1) — 100 ns — 8 TF SCIO Input Fall Time (Note 1) — 100 ns — TSTBY Standby Pulse Time % per command — 600 — µs — 10 TSS Start Header Setup Time 10 — µs — 11 THDR Start Header Low Pulse Time 5 — µs — 12 TSP Input Filter Spike Suppression (SCIO) — 50 ns (Note 1) 13 TWC Write Cycle Time (byte or page) — — 5 10 ms ms Write, WRSR commands ERAL, SETAL commands 14 — Endurance (per page) 1M — cycles 25°C, VCC = 5.5V (Note 2) 9 Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained on Microchip’s web site: www.microchip.com. 3: A Unit Interval (UI) is equal to 1-bit period (TE) at the current bus frequency. TABLE 1-3: AC TEST CONDITIONS AC Waveform: VLO = 0.2V VHI = VCC - 0.2V CL = 100 pF Timing Measurement Reference Level Input 0.5 VCC Output 0.5 VCC © 2008 Microchip Technology Inc. Preliminary DS22122A-page 3 11AA02E48 FIGURE 1-1: 10 BUS TIMING – START HEADER 11 2 SCIO Data ‘0’ FIGURE 1-2: Data ‘1’ Data ‘0’ Data ‘1’ Data ‘0’ Data ‘0’ Data ‘1’ MAK bit NoSAK bit BUS TIMING – DATA 2 7 8 Data ‘1’ Data ‘0’ 12 SCIO Data ‘0’ FIGURE 1-3: Data ‘1’ Data ‘1’ BUS TIMING – STANDBY PULSE 9 SCIO Standby Mode FIGURE 1-4: BUS TIMING – JITTER 2 3 Ideal Edge from Master DS22122A-page 4 2 3 Ideal Edge from Master Preliminary 6 6 Ideal Edge from Slave 6 6 Ideal Edge from Slave © 2008 Microchip Technology Inc. 11AA02E48 2.0 FUNCTIONAL DESCRIPTION 2.1 Principles of Operation The 11AA02E48 family of serial EEPROMs support the UNI/O® protocol. They can be interfaced with microcontrollers, including Microchip’s PIC® microcontrollers, ASICs, or any other device with an available discrete I/O line that can be configured properly to match the UNI/O protocol. The 11AA02E48 devices contain an 8-bit instruction register. The devices are accessed via the SCIO pin. Data is embedded into the I/O stream through Manchester encoding. The bus is controlled by a master device which determines the clock period, controls the bus access and initiates all operations, while the 11AA02E48 works as slave. Both master and slave can operate as transmitter or receiver, but the master device determines which mode is active. FIGURE 2-1: BLOCK DIAGRAM STATUS Register HV Generator EEPROM Memory Control Logic I/O Control Logic X Array Dec Page Latches CurrentLimited Slope Control Y Decoder SCIO VCC VSS Note: Sense Amp. R/W Control This data sheet documents only the device’s features and specifications that are in addition to the features and specifications of the 11AA020 device. For information on the features and specifications shared by the 11AA02E48 and 11AA020 devices, see the “11AAXXX/11LCXXX Family Data Sheet” (DS22067). © 2008 Microchip Technology Inc. Preliminary DS22122A-page 5 11AA02E48 3.0 PRE-PROGRAMMED EUI-48™ NODE ADDRESS The 11AA02E48 is programmed at the factory with a globally unique, EUI-48™ and EUI-64™ compatible node address stored in the upper 1/4 of the array and write-protected through the STATUS register. The remaining 1,536 bits are available for application use. The 6-byte EUI-48™ node address value is stored in array locations 0xFA through 0xFF, as shown in Figure 3-2. The first 3 bytes are the Organizationally Unique Identifier (OUI) assigned to Microchip by the IEEE Registration Authority. The remaining 3 bytes are the Extension Identifier, and are generated by Microchip to ensure a globally-unique, 48-bit value. 3.1 FIGURE 3-1: MEMORY ORGANIZATION 00h Standard EEPROM Write-Protected EUI-48™ Block FIGURE 3-2: EUI-64™ Support The pre-programmed EUI-48 node address can easily be encapsulated at the application level to form a globally unique, 64-bit node address for systems utilizing the EUI-64 standard. This is done by adding 0xFFFE between the OUI and the Extension Identifier, as shown below. C0h FFh EUI-48 NODE ADDRESS PHYSICAL MEMORY MAP EXAMPLE 24-bit Organizationally Unique Identifier Description Data 00h Array Address FAh 04h A3h 24-bit Extension Identifier 12h 34h 56h FFh Corresponding EUI-48™ Node Address: 00-04-A3-12-34-56 Corresponding EUI-64™ Node Address: 00-04-A3-FF-FE-12-34-56 3.2 Factory-Programmed Write Protection In order to help guard against accidental corruption of the EUI-48 node address, the BP1 and BP0 bits of the STATUS register are programmed at the factory to ‘0’ and ‘1’, respectively, as shown in the following table: 7 X — 6 X — 5 X — 4 X — 3 BP1 0 2 BP0 1 1 WEL — 0 WIP — This protects the upper 1/4 of the array (0xC0 to 0xFF) from write operations. This array block can be utilized for writing by clearing the BP bits with a Write Status Register (WRSR) instruction. Note that if this is performed, care must be taken to prevent overwriting the EUI-48 value. DS22122A-page 6 Preliminary © 2008 Microchip Technology Inc. 11AA02E48 4.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 4-1. TABLE 4-1: Name PIN FUNCTION TABLE 3-pin SOT-23 8-pin SOIC SCIO 1 5 Serial Clock, Data Input/Output VCC 2 8 Supply Voltage Ground VSS 3 4 NC — 1,2,3,6,7 4.1 Description No Internal Connection Serial Clock, Data Input/Output (SCIO) SCIO is a bidirectional pin used to transfer commands and addresses into, as well as data into and out of, the device. The serial clock is embedded into the data stream through Manchester encoding. Each bit is represented by a signal transition at the middle of the bit period. © 2008 Microchip Technology Inc. Preliminary DS22122A-page 7 11AA02E48 5.0 PACKAGING INFORMATION 5.1 Package Marking Information 8-Lead SOIC Example: XXXXXXXT XXXXYYWW NNN 11A2E48I SN e3 0828 1L7 3-Lead SOT-23 Example: XXNN E217 1st Line Marking Code Part Number SOT-23 I Temp. 11AA02E48 Note: Legend: XX...X Y YY WW NNN e3 * Note: DS22122A-page 8 E2NN NN = Alphanumeric traceability code Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Preliminary © 2008 Microchip Technology Inc. 11AA02E48 !"#$% & 2%& %!% 3") ' % 3 $%%"% %% 144)))& &4 3 D e N E E1 NOTE 1 1 2 3 α h b h A2 A c φ L A1 L1 5% & 6&% 7!&($ β 66-- 7 7 78 9 : % 8;% < 0+ < ""33 . < < %"$$* < . 8="% - ""3="% - ,0+ 86% 0+ . >0+ +&$? %@ . < . 2%6% 6 < 2% % 6 -2 2% A < :A 6"3 < . 6"="% ( , < . "$% .A < .A "$%0%%& .A < .A & !"#$%!&'(!%&! %(%")%%%" *$%+% % , & "-"%!"&"$ %! "$ %! %#".&& " & "% -/. 0+1 0 & %#%! ))%!%% -21 $& '! !)%!%%'$$&% ! ) +.0 © 2008 Microchip Technology Inc. Preliminary DS22122A-page 9 11AA02E48 !"#$% & 2%& %!% 3") ' % 3 $%%"% %% 144)))& &4 3 DS22122A-page 10 Preliminary © 2008 Microchip Technology Inc. 11AA02E48 '''"'(% & 2%& %!% 3") ' % 3 $%%"% %% 144)))& &4 3 b N E E1 2 1 e e1 D c A A2 φ A1 L 5% & 6&% 7!&($ 66-- 7 78 9 7 , 6"% .0+ 8!% "6"% 8;% : < ""33 . %"$$ < 0+ 8="% - < > ""3="% - > , 86% > ,. 2%6% 6 , . > 2% A < A 6"3 : < 6"="% ( , < . & & "-"%!"&"$ %! "$ %! %#".&& " & "% -/. 0+1 0 & %#%! ))%!%% ) +0 © 2008 Microchip Technology Inc. Preliminary DS22122A-page 11 11AA02E48 APPENDIX A: REVISION HISTORY Revision A (12/08) Original release of this document. DS22122A-page 12 Preliminary © 2008 Microchip Technology Inc. 11AA02E48 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2008 Microchip Technology Inc. Preliminary DS22122A-page 13 11AA02E48 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: 11AA02E48 Y N Literature Number: DS22122A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS22122A-page 14 Preliminary © 2008 Microchip Technology Inc. 11AA02E48 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X X /XX Tape & Reel Temperature Package Range Examples: a) b) Device: 11AA02E48 = Tape & Reel: T Blank = = Tape and Reel Tube Temperature Range: I = -40°C to+85°C(Industrial) Package: SN TT = = 8-lead Plastic SOIC (3.90 mm body) 3-lead SOT 23 (Tape and Reel only) © 2008 Microchip Technology Inc. 2 Kbit, 1.8V UNI/O Serial EEPROM with EUI-48™ Node Identity Preliminary c) 11AA02E48T-I/TT = 2 Kbit, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, SOT-23 package 11AA02E48-I/SN = 2 Kbit, 1.8V Serial EEPROM, Industrial temp., SOIC package 11AA02E48T-I/SN = 2 Kbit, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package DS22122A-page 15 11AA02E48 NOTES: DS22122A-page 16 Preliminary © 2008 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC, SmartShunt and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2008, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2008 Microchip Technology Inc. Preliminary DS22122A-page 17 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 01/02/08 DS22122A-page 18 Preliminary © 2008 Microchip Technology Inc.