GPM140 Safety Certs

File E116994
Vol. 1
Sec. 27
and Report
Page 1
Issued:
Revised:
1992-05-19
2003-10-23
DESCRIPTION
PRODUCT COVERED:
Component - Switching Power Supplies for use in Medical and Dental
Equipment; Models GPM140-5, -12, -13, -15, -24, -28, -30; may be followed by C, -T, -T1, or -T2; MSP1363, MSP1402.
ELECTRICAL RATING:
Input:
Models GPM140 Series, MSP1363, MSP1402
100-240 V ac, 50/60 Hz, 4.0 A
Outputs:
Model
GPM140-5
GPM140-12
GPM140-13
GPM140-15
MSP1363
GPM140-24
GPM140-28
GPM140-30
MSP 1402
Volts
5
12
13
15
12
24
28
30
17
MAXIMUM OUTPUT AMPS AND WATTS
CONVECTION COOLING
FORCED AIR COOLING (1)
Without Cover
With Cover
With & Without Cover
26.0
11.7
10.8
9.3
11.7
5.8
5.0
4.7
8.2
A
A
A
A
A
A
A
A
A
130
140
140
140
140
149
140
140
140
W
W
W
W
W
W
W
W
W
24.0
10.0
9.2
8.0
10.0
5.8
5.0
4.7
-
A
A
A
A
A
A
A
A
120
120
120
120
120
140
140
140
-
W
W
W
W
W
W
W
W
32.0
13.4
12.3
10.7
13.4
6.7
5.8
5.3
9.4
A
A
A
A
A
A
A
A
A
160
160
160
160
160
160
160
160
160
W
W
W
W
W
W
W
W
W
(1) Reference the Installation Instructions, ILL. 1.
ENGINEERING CONSIDERATIONS (NOT FOR FIELD REPRESENTATIVE'S USE):
For use in products where the acceptability of the combination is
determined by Underwriters Laboratories Inc.
The products, models GPM140-5, -12, -13, -15, -24, -28, and -30, were
evaluated to the Second Edition of the Standard for Medical and Dental
Equipment, UL 544; and the First Edition of the Standard For Medical
Electrical Equipment, Part 1: General Requirements for Safety, UL 2601-1. An
insulation diagram is provided as Ill. 3 and the manufacturer's installation
instructions are provided as Ill. 1.
The products, models MSP1363 and MSP1402 were evaluated to the Second
Edition of the Standard for Medical and Dental Equipment, UL 544 only.
File E11699
Vol. 1
Sec. 27
and Report
Page 2
Issued:
Revised:
1992-05-19
2003-10-23
Conditions of Acceptability - When installed in the end-use equipment,
the following are among the considerations to be made:
1.
The power supplies, models GPM140-5, -12, -13, -15, -24, -28, and -30,
have been judged on the basis of the required spacings in the First
Edition of the Standards for Medical Electrical Equipment, Part 1:
General Requirements for Safety, UL 2601-1, and the second edition of
the Standard for Medical and Dental Equipment, UL 544, which covers the
end use product for which the component is designed. The power
supplies, models MSP1363 and MSP1402 have been judged on the basis of
the required spacings in the Second Edition of the Standard for Medical
and Dental Equipment, Professional, UL 544, which covers the end-use
product for which the component designed.
2.
The device shall be installed in compliance with the
enclosure, mounting, spacing, casualty markings and segregation
requirements of the end-use application.
3.
Consideration should be given to measuring the temperature on power
electronic components and transformer windings when the power supply is
installed in the end-use equipment. All transformers comply with Class
155 limits.
4.
Input and output connectors, when provided, are not acceptable for field
connections, they are only intended for connection to mating connectors
of internal wiring inside the end-use machine. The acceptability of the
mating connectors relative to secureness, insulating materials, and
temperature shall be considered.
5.
The end-use product shall ensure that a fuse warning
marking is provided adjacent to the primary fuse (F1). The marking
shall include the following wording: "WARNING - For continued
protection against risk of fire, replace only with the same type and
ratings of fuse" and the fuse ratings. The minimum letter height 7/64
in.
6.
The power supply should be properly bonded to ground in
the end-use product.
7.
The power supply has been evaluated for patient care equipment, but not
patient connected.
8.
The output circuits have not been evaluated for direct patient
connection (Type B, BF or CF).
File E116994
Vol. 1
Sec. 27
and Report
Page 3
Issued:
Revised:
1992-05-19
1997-09-03
9.
This power supply has been evaluated for use in 25°C ambient.
The end
use product shall ensure that the airflow and power ratings listed in
the electrical ratings output table are not exceeded.
10.
Leakage current testing should be repeated in the end product
application.
11.
The UL 2601 power supplies were evaluated as Reinforced insulation
between primary and secondary; basic insulation between primary to
ground; and operational insulation only between secondary to ground.
12.
The UL 2601 power supplies have been evaluated as Class I, continuous
operation, ordinary equipment and has not been evaluated for use in the
presence of a flammable anaesthetic mixture with air, oxygen, or nitrous
oxide.
13.
Fusing in the end product shall be considered since only one fuse rated
5 A, 250 V is provided in the hot side of the input supply circuit.
14.
For the UL 2601-1 power supplies, under normal and single fault
conditions, the outputs do not exceed 25 V ac or 60 V dc.
DC Power Supplies, Inc.
STATEMENT OF COMPLIANCE
File Number: LR 46516
Date Issued: October 16, 2003
In accordance with the conditions established by the CSA Category
Certification Program, the models listed below are eligible to bear the CSA
mark.
Issued By: Ross Sacolles
Product Safety Engineer
Signature:
CLASS
5311-03 - POWER SUPPLIES - Component Type
PRODUCTS
Component power supplies for use with Information Processing and Business Equipment,
where the suitability of the combination is to be determined by the Canadian Standards
Association.
- Model GPC140-5, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 5 V/32
A; 160 W with 26 cfm airflow; 130 W with convection cooling, 120 W with cover.
- Model GPC140-12, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 12
V/13.4 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 120 W with cover.
- Model GPC140-15, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 15
V/10.7 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 120 W with cover.
- Model GPC140-24 and GPC140-24P0, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc
output rated 24 V/6.7 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 140 W
with cover.
- Model GPC140-28 and SP1382, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output
rated 28 V/5.8 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 140 W with
cover.
CLASS
5311-20 - POWER SUPPLIES - Component Type
PRODUCTS
Component power supplies for use with Medical Equipment, where the suitability of the
combination is to be determined by the Canadian Standards Association.
- Model GPM140-5, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 5 V/32
A; 160 W with 26 cfm airflow; 130 W with convection cooling, 120 W with cover.
- Model GPM140-12, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 12
V/13.4 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 120 W with cover.
- Model GPM140-13, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 13
V/12.3 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 120 W with cover.
- Model GPM140-15, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 15
V/10.7 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 120 W with cover.
- Model GPM140-24, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 24
V/6.7 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 140 W with cover.
- Model GPM140-28, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 28
V/5.8 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 140 W with cover.
- Model GPM140-30, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 30
V/5.3 A; 160 W with 26 cfm airflow; 140 W with convection cooling, 140 W with cover.
- Model MSP1363, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 12
V/13.4 A; 160 W with 26 cfm airflow.
- Model MSP1402, (Level 3), input rated 100-240 V, 50/60 Hz, 4 A; dc output rated 17 V/9.2 A;
160 W with 26 cfm airflow; 140 W with convection cooling.
Notes
1.
Maximum ambient temperature for continuous output power of 160 Watts is 50 °C.
2.
Model numbers may include the following suffixes:
-C for cover.
-T for input and output terminal blocks, -T1 for input terminal block or
-T2 for output terminal block.
APPLICABLE REQUIREMENTS
CSA Standard C22.2 No. 0-1991:
0.4-M1982:
234-M90:
601.1-M90:
TIL CA-08:
General Requirements – Canadian
Electrical Code, Part II
Bonding and Grounding of Electrical Equipment
(Protective Grounding)
Safety of Component Power Supplies
Medical Electrical Equipment
Power Supplies for use in Medical Electrical Equipment