GPMP600 Instructions

CONDOR DC POWER SUPPLIES INC.
2311 STATHAM PKWY
OXNARD, CA 93033 + 805-486-4565
GPMP600/700 SERIES
INSTALLATION INSTRUCTIONS
RA RATINGS:
Input: GPMP600: 100-240 V ac, 8.5 A, 50/60 Hz
GPMP700: 100-240 V ac, 9.5 A, 50/60 Hz
Outputs:
Model #
GPMP600-24-YYY
GPMP600-28-YYY
GPMP600-36-YYY
GPMP700-48-YYY
NOTES: 1.
2.
3.
4.
5.
V
24
28
36
48
Output #1
A
25/27 pk
21.5/23.5 pk
17/19 pk
14.6/15.6 pk
Total
Watts
600
600
600
700
Maximum ambient temperature for rated output power is 50°C utilizing two integral 27 CFM Fans.
Maximum Operating Relative Humidity 96%, no condensation.
Storage: -40 to +85 °C. Units should be allowed to warm-up under non-condensing conditions before
application of power.
Peak current, 60 Sec with a 10% duty cycle
YYY indicates front cover colors and mounting options not related to safety.
CERTIFICATION: All models are Certified to be in compliance with the applicable requirements of UL/CSA/EN/IEC
60601-1, 1st. Ed.
CLASSIFICATION:
(In accordance with subclause 5 of EN 60601-1)
(5.1) Protection against electric shock = Class I
(5.2) Degree of protection against electric shock = Not acceptable for applied part without
additional isolation (contact factory for details)
(5.3) Protection against harmful ingress of water = Ordinary (no protection)
(5.5) Have not been evaluated for use in the presence of a flammable anaesthetic mixture with
air, oxygen, or nitrous oxide. This evaluation is to be made on the end equipment by the OEM.
(5.6) Mode of operation = Continuous
GROUNDING: Protection Class I requires that at least one of the ground pins (Z28, D26) be bonded to Protective Earth in
the end application.
OUTPUTS: The outputs are not acceptable for patient connection without additional isolation.
OVERVOLTAGE PROTECTION: The output is monitored for an overvoltage condition. In some applications where an
overvoltage condition could result in a hazard as defined in applicable safety standards, redundant or additional overvoltage
protection may be required. Consult factory for details.
TEMPERATURES: The maximum operating temperatures of certain safety components, as defined in the applicable safety
standards, must not be exceeded after installation to preserve the intended safety. The output power, ambient air temperature
and the availability, amount, direction and/or restriction of airflow influence the temperatures of these components.
FUSING: Fusing is provided only in the Input Line conductor of the power supply. Additional fusing, external to the power
supply must be provided to meet the requirements of the applicable standards.
WARNING! RISK OF FIRE!: A blown fuse is an indication of catastrophic failure of circuit component(s). Repair must
be performed by Condor authorized personnel.
41-35343-0002A 8/5/04
INSTALLATION INSTRUCTIONS GPMP600/700 SERIES (Contd.)
WARNING! SHOCK HAZARD! Dangerous voltages are present on some components, printed wiring traces and heatsinks.
AIRFLOW/COOLING: The GPHP600/700 series is designed with two integral fans that are rated 54 cfm total.
VOLTAGE ADJUSTMENT: Factory set to specified voltage. User accessible pot allows adjustment over a range of ±5%
of nominal voltage. The potentiometer is located on the A2 PWB located behind and above J1.
EXPLANATION OF SYMBOLS
Alternating Current
Direct Current
Attention, Consult
Accompanying Documents
Attention, Dangerous Voltages
Earth (Ground)
VOLTAGE ADJUSTMENT: Factory set to specified voltage. User
accessible pot allows adjustment over a range of ±5% of nominal voltage.
The potentiometer is located on the A2 PWB located behind and above J1.
CONNECTIONS
Connector: ERNI Type H15 P/N 123767 or AVX ELCO 108456015001169
AC INPUT
Line
Neutral
Ground
DIN 41612 Style H15
STATUS and CONTROL
Z32
D30
Z28, D26
AC Power Fail
DC Power Good
Inhibit
D22
Z20
Z24
Reference to Common
DC OUTPUT
Output #1
Z12, D14, Z16, D18
Z4, D6, Z8, D10
Main Output
Rtn (Common)
Condor DC Power Supplies Inc. will not be liable for the safety, reliability or performance of these power supplies if a) any changes,
modifications or repairs are carried out by other than authorized agents of Condor DC Power Supplies Inc., or b) the installation of the supply
is not in accordance with these installation instructions and the applicable UL, CSA, and EN/IEC safety standards.
41-35343-0002A 8/5/04