526 Thermal Windows - Architectural Detail Manual

AUGUST, 2011
526 IsoPort TM WINDOW
1
INDEX
E.C. 97911-32
FEATURES. . . . . . . . . . . . . . . .
PICTORIAL VIEWS. . . . . . . . . .
DETAILS OPEN-IN. . . . . . . . . .
DETAILS OPEN-OUT. . . . . . . .
STRUCTURAL LIMITATIONS. .
THERMAL TRANSMITTANCE.
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
Metric (SI) conversion figures are included throughout these details for reference.
Numbers in parentheses ( ) are millimeters unless otherwise noted.
The following metric (SI) units are found in these details:
m - meter
cm - centimeter
mm - millimeter
s - second
Pa - pascal
MPa - megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessary
for product improvement.
kawneer.com
2
. 3
. 4
. 5
. 6
. 7
. . . . . . . . . . . . . . . . . . . . . . . . . .
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED
ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT
CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING
HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Architects - These concepts have been expanded and modified to afford you design freedom.
Please contact your Kawneer representative for further assistance.
The extrusions and window types illustrated in this catalog are standard products for Kawneer.
FEATURES
AUGUST, 2011
E.C. 97911-32
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
526 IsoPort TM WINDOW
Full range of projected open-in and open-out vents and hinged casements.
14.6 mm ISOPORT ® glass-reinforced nylon 6/6 thermal break provides:
Improved condensation resistance and thermal transmittance performance capability.
Rigid profile with composite structural performance.
Exterior / interior finish options.
Meets or exceeds the highest performance levels of CSA standard CAN/CSA-A440 windows.
Sash features mitred and clip, adhesive, stake joinery to provide rigid and weather tight corners.
Operating sash uses tubular extrusions.
Factory fabricated and assembled.
Optional full rain screen capability.
Accommodates 25 mm sealed glazing units.
Exterior pre-shim butyl glazing tapes.
Interior EPDM rubber glazing gaskets.
Lock-in glass stop.
Optional insect screens.
kawneer.com
© Kawneer Company, Inc., 2011
Glass installed and replaced from interior.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AUGUST, 2011
kawneer.com
526 IsoPort TM WINDOW
E.C. 97911-32
PICTORIAL VIEWS
PROJECTED VENTS
TOP PROJECTED
OPEN-OUT
(TPO)
Open in
Open out
Long equal legs
(typical)
CASEMENTS
BOTTOM PROJECTED
OPEN-IN
(BPI)
SIDE HINGED
OPEN-OUT
(SHO)
Open in
SIDE HINGED
OPEN-IN
(SHI)
INTERIOR VIEW
PERIMETER FRAME SECTIONS
Open out
Short interior leg
(for curtainwall installation)
3
TYPE 801
BOTTOM PROJECTED
OPEN-IN (BPI)
VENTILATOR
4"
101.6
5"
127.0
1
JAMB
2
JAMB
4
Fixed framing D.L.O.
3
HEAD
4
SILL
2
TYPE 813 R.H. SHOWN
TYPE 807 L.H. OPPOSITE
SIDE HINGED
OPEN-IN (SHI)
CASEMENT
(Typ.)
kawneer.com
© Kawneer Company, Inc., 2011
1
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
DETAILS OPEN-IN
(Typ.)
526 IsoPort TM WINDOW
3 3/16"
81.0
2
Fixed framing D.L.O.
3 3/16"
81.0
4
5"
127.0
(Typ.)
1
4"
101.6
2 1/4"
57.2
4
AUGUST, 2011
E.C. 97911-32
SCALE 1/4 FULL SIZE
© Kawneer Company, Inc., 2011
kawneer.com
1
TYPE 802
TOP PROJECTED
OPEN-OUT (TPO)
VENTILATOR
4"
101.6
5"
127.0
1
JAMB
2
JAMB
4
Fixed frame D.L.O.
3
HEAD
4
SILL
(Typ.)
E.C. 97911-32
3 3/16"
81.0
2
5"
127.0
3 3/16"
81.0
4
4"
101.6
(Typ.)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
Fixed framing D.L.O.
2 1/4"
57.2
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
AUGUST, 2011
526 IsoPort TM WINDOW
5
DETAILS OPEN-OUT
SCALE 1/4 FULL SIZE
3
2
TYPE 814 R.H. SHOWN
TYPE 808 L.H. OPPOSITE
SIDE HINGED
OPEN-OUT (SHO)
CASEMENT
(Typ.)
526 IsoPort TM WINDOW
AUGUST, 2011
LIMITATION CHARTS
E.C. 97911-32
BPI VENTILATOR SIZE CHART
TPO VENTILATOR SIZE CHART
FRAME WIDTH IN METRES
1.5
FOUR
LOCKS
1.0
THREE LOCKS
3
TWO LOCKS
2
ONE LOCK
0.5
1
2
3
4
5
FRAME HEIGHT IN FEET
4
0.5
5
FRAME HEIGHT IN METRES
FRAME HEIGHT IN FEET
5
1.0
1.0
1.5
4
1.0
THREE LOCKS
3
TWO LOCKS
2
ONE LOCK
0.5
1
2
3
4
5
FRAME WIDTH IN FEET
FRAME WIDTH IN FEET
MINIMUM SIZE = 13-1/4" x 13-1/4"
MAXIMUM SIZE = 60" x 48"
MINIMUM SIZE = 13-1/4" x 13-1/4"
MAXIMUM SIZE = See above.
Note: All TPO vents with pivot shoe operators are supplied
with (2) claw handles. MINIMUM SIZE = 20-5/8" x 19"
For vents 21" to 31" wide - max. opening = 1.75"
For vents 32" to 60" wide - max. opening = 7.25"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FRAME WIDTH IN METRES
0.5
FRAME HEIGHT IN METRES
6
SHI/SHO CASEMENT SIZE CHART
THREE LOCKS
5
4
OPEN-IN
516 Shown
518 Similar
1.0
1.5
TWO LOCKS
1.0
3
ONE LOCK
2
27-722
AIR SEAL GASKET
(TYPICAL)
528-304*
POCKET CLOSURE
(SILL ONLY)
JAMB
SILL
OPEN-OUT
516 Shown
518 similar
0.5
2
3
1
FRAME WIDTH IN FEET
27-722
AIR SEAL GASKET
(TYPICAL)
MINIMUM SIZE = 13-1/4" x 13-1/4"
MAXIMUM SIZE = 36" x 72"
528-304*
POCKET CLOSURE
(SILL ONLY)
Note: All SHO casements with roto operators,
MINIMUM SIZE = 16-3/4" x 16-3/4"
JAMB
SILL
*Note: Use 528-304 pocket filler and full perimeter wet seal at
interior when rain screen vent frame installation is required.
kawneer.com
© Kawneer Company, Inc., 2011
0.5
FRAME HEIGHT IN METRES
FRAME HEIGHT IN FEET
6
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
RAIN SCREEN WINDOW
FRAME WIDTH IN METRES
526 IsoPort TM WINDOW
AUGUST, 2011
7
THERMAL TRANSMITTANCE
E.C. 97911-32
The window thermal transmittance values (U - values) shown in the chart below are based on CSA - A440.2 "Energy Performance
Evaluation of Windows and Sliding Glass Doors". U - values of the center of glass, edge of glass and frame areas were computed using
the VISION and FRAME thermal simulation programs. Overall window U - values were calculated using the following relationship:
U w = (U c A c + U e A e + U f A f )/A w
where
U w = U-value of complete window product
U c = calculated center of glass U-value
U e = calculated edge of glass U-value
U f = calculated frame U-value
A c = center of glass area
A e = edge of glass area
A f = frame area
A w = total window area
OVERALL WINDOW U-VALUE (U w )
For window configurations as shown with height (h) equal to width (w).
AREA IN SQUARE METRES
2
4
w
SEALED UNIT GLAZING TYPE
A = 6mm clear / / " air / 6mm clear / metal spacer
12
WINDOW U w IN BTU / hr ft 2 °F
h
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.80
4
0.60
A
3
B
C
D
E
0.40
2
0.20
1
B = 6mm clear / 1/2" air / 6mm low-e 1 / metal spacer
C = 6mm clear / 1/2" argon / 6mm low-e 1 / metal spacer
D = 6mm clear / 1/2" argon / 6mm low-e 1 / Helima thermally broken spacer
E = 6mm clear / 1/2" argon / 6mm low-e
2
/ Helima thermally broken spacer
0
20
40
60
AREA IN SQUARE FEET
1 - low-e coating emittance = 0.10
2 - low-e coating emittance = 0.03
NOTES: THE ABOVE SEALED UNIT GLAZING OPTIONS ARE PRESENTED FOR THE PURPOSES OF ILLUSTRATING THERMAL
PERFORMANCE CAPABILITIES.
FOR WINDOWS WITH HEIGHT NOT EQUAL TO WIDTH, WHEN ADDING INTERMEDIATE VERTICALS OR HORIZONTALS,
OR DIFFERENT GLASS INFILL, THE OVERALL WINDOW U - VALUE MAY VARY.
THE SPECIFIER SHOULD SELECT GLASS TO MEET THE PERFORMANCE REQUIREMENTS OF THE PROJECT.
kawneer.com
WINDOW U w IN W / m 2 °C
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
For some regions and projects there may be minimum energy efficiency requirements for the building envelope, and its components,
including windows. The shading coefficient (SC) and the thermal transmittance (U - value) of the window is then required to determine
whether the building design complies with the specified energy requirements. Shading coefficient depends on the glass selected and
should be obtained from the glass supplier. The U - value of the window varies with the type of glass and sealed unit edge construction,
the window frame, and the relative areas of these components.
kawneer.com
© Kawneer Company, Inc., 2011
BLANK PAGE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
526 IsoPort TM WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8
AUGUST, 2011
E.C. 97911-32