NSNJ9200 Apr. 2014 New JRC SAW FILTER NSNJ9200 Application 1582.471MHz GPS / GLONASS / Beidou Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss 1559.052~1563.144MHz Ripple Deviation Input and Output VSWR Group Delay Time Deviation Out of Band Rejection (Relative to Through Level) Spec. Typical 50 1582.471MHz 3.5dB max.(*1) 2.5dB 4.0dB max. 1574.42~1576.42MHz 3.0dB max. 2.0dB 1597.55~1605.89MHz 3.5dB max. (*1) 2.5dB 4.0dB max. 1559.052~1563.144MHz 2.0dB max. 0.5dB 1574.42~1576.42MHz 1.5dB max. 0.3dB 1597.55~1605.89MHz 2.0dB max. 0.5dB 1559.052~1563.144MHz 2.5 max. 1.4 1574.42~1576.42MHz 2.5 max. 1.4 1597.55~1605.89MHz 2.5 max. 1.7 1597.55~1605.89MHz 15ns max. 5ns 0.3~960MHz 34dB min. 43dB 1427~1463MHz 35dB min. 41dB 1625~1660MHz 15dB min. 27dB 1710~1785MHz 40dB min. 47dB 1850~1910MHz 40dB min. 43dB 1920~1980MHz 35dB min. 42dB 2400~2496MHz 30dB min. 33dB 2496~2690MHz 25dB min. 30dB (*1) (Operating Temperature Range: -40~+85ºC) (Operating Temperature Range: -40~+105ºC) Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +10dBm 7.5V -40~+105ºC -40~+110ºC Mechanical Specifications: (Fig.2) Package is designed as small as 2.0x1.6x0.65[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html NSNJ9200 Apr. 2014 10nH OUT 10nH 50 IN 50 Fig.1 Measuring circuit (2) 2.0±0.15 (1) 1.6 ± 0 . 1 5 (3) YD 0.7Max. (4) 2 Marking 40.50 ± 0 . 1 0 3 40.55±0.10 4 8(0.075) 1 (1) Lot Number : Year (2) Lot Number : Month October : X November : Y December : Z (3) Lot Number : Date 0~ 9 : 0 10~19 : 1 20~31 : 2 (4) Part Number Mark Fig.2 Package dimensions (in mm) 1. 80 4- 0. 60 2. 20 4- 0. 65 Fig.3 Desirable land area (in mm) Pin no. Connection 1 GND 2 IN 3 GND 4 OUT NSNJ9200 Apr. 2014 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +105ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. The information contained herein may be changed without prior notice. It is therefore advisable to contact New Japan Radio Company before proceeding with the design of equipment incorporating this product. 3. The products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). New Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. NSNJ9200 Apr. 2014 Insertion Loss [dB] 0 FREQUENCY CHARACTERISTICS 0 20 2 40 4 60 6 80 8 100 10 CH1 : center 1582.5 span 300 CH2 : center 1582.5 span 300 S11 S22 S22 11 9 9 VSWR VSWR S11 11 7 5 3 7 5 3 1 1432.5 1732.5 1 1432.5 Frequency [MHz] S21 0 InsertionLoss [dB] 1732.5 Frequency [MHz] 20 40 60 80 100 0 5000 Frequency [MHz] New Japan Radio Co.,Ltd. Insertion Loss [dB] S21