NSTS1441 Apr. 2013 NewJRC SAW FILTER NSTS1441 Application 243.95MHz PHS IF Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Nominal Center Frequency (f0) 3dB Band Width Insertion Loss at f0 Ripple f0±100kHz Group Delay Time Ripple f0±100kHz Out of Band Rejection f0±600kHz (Relative to f0±10.7MHz Through Level) f0±21.4MHz Spec. Typ. 243.95MHz 260kHz min. 4.0dB max. 3.0dB 1.2dB max. 0.4dB 1.2usec max. 0.4usec 25dB min. 30dB 40dB min. 60dB 60dB min. 65dB (Operating Temperature Range : -20~+85ºC) Maximum Rating: (Table 2) Table2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +5dBm 7.5V -20~+85ºC -30~+85ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html (Japanese) (English) NSTS1441 Apr. 2013 110nH LQW18A IN 50Ω 1 2 2pF GRM18 110nH LQW18A 6 SAW OUT 50Ω 5 3 2pF GRM18 4 Fig.1 Measuring circuit (a) 3. 0±0. 15 ( b) 3. 0 ± 0. 1 5 １７２ ( c) Ｔ７ (1) ( 0. 6) ( 0. 2 5) 1. 1 5 ± 0. 1 5 ( 2) 4 ( 0. 6) [ 2 x] 3 2 5 ( 1. 80) 1 ( 0. 75) ( 0. 45) [ 4x] ( 0. 5 3) [ 4 x] 6 Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) Marking (1) Lot Number (a) Year (b) Month *Oct.--Nov.--Dec.--(c) Date 1-9--10-19--20-31--(2) Part Number Mark Pin no. 1 2 3 4 5 6 Connection GND IN/OUT GND GND OUT/IN GND X Y Z 0 1 2 NSTS1441 Apr. 2013 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. Smith Chart Insertion Loss 0 S11 2 4 6 8 [dB] 10 243.45 243.95 Frequency[MHz] Return Loss 244.45 S22 [5dB/div] Center Freq. 243.95 [MHz] Freq.Span 1 [MHz] New Japan Radio Co.,Ltd. S21 group delay Reference Division 500[nsec] group delay [nsec] 0[dB] 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 0 243.45 243.95 frequency [MHz] New Japan Radio Co.,Ltd. 244.45 Insertion Loss 0 Reference 0 [dB] 20 Division 10 [dB] 40 60 80 [dB] 100 238.95 243.95 248.95 Frequency[MHz] New Japan Radio Co.,Ltd Insertion Loss 0 Reference 0 [dB] 20 Division 10 [dB] 40 60 80 [dB] 100 219 244 269 Frequency[MHz] New Japan Radio Co.,Ltd