NSNJ2000

NSNJ2000 Nov-2013
NewJRC SAW FILTER
NSNJ2000
Application
PHS-IF f0=265.55MHz BW=0.2MHz
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Nominal Center Frequency (f0)
3dB Band Width (from f0)
Insertion Loss at f0
Ripple
f0±100kHz
Group Delay Time Ripple
f0±100kHz
Out of Band Rejection
f0±600kHz
(Relative to
f0±1.2MHz
Through Level)
f0±21.5~21.7MHz
Spec.
265.55MHz
±130kHz min.
4.0dB max.
1.2dB max.
1.2usec max.
25dB min.
40dB min.
60dB min.
Typ.
±275 kHz
3.2dB
0.8dB
0.5usec
30dB
60dB
63dB
(Operating Temperature Range : -20~+85ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+0dBm
7.5V
-20~+85ºC
-30~+85ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
NSNJ2000 Nov-2013
110nH
LQW18A
1
110nH
LQW18A
IN
50Ω
2
6
SAW
3
OUT
50Ω
5
2pF
GRM18
4
2pF
GRM18
Fig.1 Measuring circuit
(a)
( b)
3. 0±0. 15
3. 0 ± 0. 1 5
3X2
P7
( c)
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
Pin no.
1
2
3
4
5
6
Connection
GND
GND
IN/OUT
GND
GND
OUT/IN
X
Y
Z
0
1
2
NSNJ2000 Nov-2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
Insertion Loss [dB]
0
5
10
15
20
25
30
35
40
45
50
264.05
S21
266.05
3000
2800
2600
2400
2200
2000
1800
1600
1400
1200
1000
265.05
267.05
0
10
20
30
40
50
60
70
80
90
100
240.55
Group Delay [nsec]
0
1
2
3
4
5
6
7
8
9
10
265.05
265.55
Frequency [MHz]
S21
Insertion Loss [dB]
Insertion Loss [dB]
NSNJ2000 Nov-2013
265.55
Frequency [MHz]
S11
S21
265.55
Frequency [MHz]
266.05
S21
265.55
Frequency [MHz]
S22
290.55