NSVS9016

NSVS9016 Jan. 2015
New JRC SAW FILTER
NSVS9016
Application
R.K.E.
f0=315MHz BW=0.6MHz
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
Typ.
Input and Output Impedance
50
Nominal Center Frequency (f0)
315MHz
Insertion Loss
314.7~315.3MHz
2.5dB max.
1.8dB
Response Variation
314.7~315.3MHz
1.5dB max.
1.0dB
Input and Output VSWR
314.7~315.3MHz
2.5 max.
1.8
Out of Band Rejection
10~295MHz
50dB min.
55dB
(Relative to Through Level)
295~305MHz
25dB min.
45dB
325~335MHz
22dB min.
28dB
335~336.05MHz
40dB min.
60dB
336.05~336.45MHz
50dB min.
60dB
336.45~1000MHz
40dB min.
43dB
(Operating Temperature Range: -40~+105ºC)
Maximum Rating: (Table 2)
Table 2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+20dBm
7.5V
-40~+105ºC
-40~+105ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15 [mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html （Japanese）
http://www.njr.com/products/device/index.html （English）
NSVS9016 Jan. 2015
OUT
50
IN
50
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
512
( c)
DJ
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Pin no.
Connection
1
GND
2
IN
3
GND
4
GND
5
OUT
6
GND
X
Y
Z
0
1
2
NSVS9016 Jan. 2015
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +105ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influences for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with the
design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). New Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please contact
our sales representatives in advance.
NSVS9016 Jan. 2015
Insertion Loss [dB]
0
FREQUENCY CHARACTERISTICS
0
20
2
40
4
60
6
80
8
100
10
CH1 : center 315 span 100
CH2 : center 315 span 100
S11
S22
S22
11
9
9
VSWR
VSWR
S11
11
7
5
3
7
5
3
1
265
365
1
265
Frequency [MHz]
InsertionLoss [dB]
0
365
Frequency [MHz]
S21
20
40
60
80
100
0.1
1500
Frequency [MHz]
New Japan Radio Co.,Ltd.
Insertion Loss [dB]
S21