NSTS9118 Jul. 2014 New JRC SAW FILTER NSTS9118 Application R.K.E f0=433.92MHz BW=0.4MHz Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typ. Input and Output Impedance 50 Nominal Center Frequency (f0) 433.92MHz Insertion Loss 2.5dB max. 1.8dB Response Variation 433.72~434.12MHz 1.5dB max. 0.7dB Input and Output VSWR 2.5 max. 1.3 Out of Band Rejection 423.92MHz(f0-10MHz) 25dB min. 40dB (Relative to Through Level) 443.92MHz(f0+10MHz) 22dB min. 28dB 10~295MHz 50dB min. 67dB 470~585MHz 50dB min. 55dB 585~630MHz 40dB min. 48dB 630~710MHz 50dB min. 60dB 710~770MHz 40dB min. 60dB 1000~1500MHz 40dB min. 47dB 2000~2500MHz 15dB min. 22dB (Operating Temperature Range: -40~+105ºC) Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -40~+105ºC -40~+105ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15 [mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html NSTS9118 Jul. 2014 OUT 50 IN 50 Fig.1 Measuring circuit (a) 3. 0±0. 15 ( b) 3. 0 ± 0. 1 5 470 ( c) DU (1) ( 0. 6) ( 0. 2 5) 1. 1 5 ± 0. 1 5 ( 2) 4 ( 0. 6) [ 2 x] 3 2 5 Marking (1) Lot Number (a) Year (b) Month *Oct.--Nov.--Dec.--(c) Date 1-9--10-19--20-31--(2) Part Number Mark ( 1. 80) 1 ( 0. 75) ( 0. 45) [ 4x] ( 0. 5 3) [ 4 x] 6 Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) Pin no. Connection 1 GND 2 IN 3 GND 4 GND 5 OUT 6 GND X Y Z 0 1 2 NSTS9118 Jul. 2014 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +105ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influences for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. The information contained herein may be changed without prior notice. It is therefore advisable to contact New Japan Radio Company before proceeding with the design of equipment incorporating this product. 3. The products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). New Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. NSTS9118 Jul. 2014 Insertion Loss [dB] 0 FREQUENCY CHARACTERISTICS 0 20 2 40 4 60 6 80 8 100 10 CH1 : center 433.92 span 100 CH2 : center 433.92 span 100 S11 S22 S22 11 9 9 VSWR VSWR S11 11 7 5 3 7 5 3 1 383.9 483.9 1 383.9 Frequency [MHz] S21 0 InsertionLoss [dB] 483.9 Frequency [MHz] 20 40 60 80 100 0 3000 Frequency [MHz] New Japan Radio Co.,Ltd. Insertion Loss [dB] S21