DG506A, DG507A, DG509A PRODUCT O BSO LETE RODUCT BSTITUTE P POSSIBLE SU IP), DG406(PLASTIC), RD DataLA Sheet STIC), HI1-0506(CE P), DG407(P DI ER C 7( 50 HI1-0 409 HI-0509, DG itle G50 , 507 May 2001 CMOS Analog Multiplexers Features The DG506A, DG507A and DG509A are CMOS Monolithic 16-Channel/Dual 8-Channel and Dual 4-Channel Analog Multiplexers, which can also be used as demultiplexers. An enable input is provided. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. • Low Power Consumption File Number 6010 • TTL and CMOS-Compatible Address and Enable Inputs • 44V Maximum Power Supply Rating • High Latch-Up Immunity • Break-Before-Make Switching A, 509 bt MO na- A channel in the ON state conducts current equally well in both directions. In the OFF state each channel blocks voltages up to the supply rails. The address inputs and the enable input are TTL and CMOS compatible over the full specified operating temperature range. The DG506A, DG507A and DG509A are pinout compatible with the industry standard devices. • Alternate Source Applications • Data Acquisition Systems • Communication Systems • Signal Multiplexing/Demultiplexing • Audio Signal Multiplexing ltix) utho ) eyrds terrpoion, inctor, ltixer, x, anl, ched eo) rer () OCI Part Number Information PART NUMBER TEMP. RANGE ( oC) DG506AAK -55 to 125 DG506ACJ 0 to 70 DG506ACY 0 to 70 DG507ABK -25 to 85 PACKAGE PKG. NO. PART NUMBER TEMP. RANGE ( oC) PACKAGE PKG. NO. 28 Ld CERDIP F28.6 DG507ACJ 0 to 70 28 Ld PDIP E28.6 28 Ld PDIP E28.6 DG507ACY 0 to 70 28 Ld SOIC M28.3 28 Ld SOIC M28.3 DG509ACJ 0 to 70 16 Ld PDIP E16.3 28 Ld CERDIP F28.6 DG509ACY 0 to 70 16 Ld SOIC M16.3 Pinouts DG506A (PDIP, CERDIP, SOIC) TOP VIEW DG507A (PDIP, CERDIP, SOIC) TOP VIEW DG509A (PDIP, SOIC) TOP VIEW 28 D V+ 1 28 DA A0 1 16 A1 NC 2 27 V- DB 2 27 V- EN 2 15 GND NC 3 26 S8 NC 3 26 S8A S16 4 25 S7 S8B 4 25 S7A S15 5 24 S6 S7B 5 24 S6A S14 6 23 S5 S6B 6 23 S5A S13 7 22 S4 S5B 7 22 S4A S12 8 21 S3 S4B 8 21 S3A S11 9 20 S2 S3B 9 20 S2A S10 10 19 S1 S2B 10 19 S1A S9 11 18 EN S1B 11 18 EN GND 12 17 A0 GND 12 17 A0 NC 13 16 A1 NC 13 16 A1 A3 14 15 A2 NC 14 15 A2 V+ 1 1 V- 3 14 V+ S1A 4 13 S1B S2A 5 12 S2B S3A 6 11 S3B S4A 7 10 S4B DA 8 9 DB CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. | Copyright © Intersil Americas Inc. 2001 DG506A, DG507A, DG509A Truth Tables DG506A DG507A A3 A2 A1 A0 EN ON SWITCH A2 A1 A0 EN ON SWITCHES X X X X 0 None X X X 0 None 0 0 0 0 1 1 0 0 0 1 1A, 1B 0 0 0 1 1 2 0 0 1 1 2A, 2B 0 0 1 0 1 3 0 1 0 1 3A, 3B 0 0 1 1 1 4 0 1 1 1 4A, 4B 0 1 0 0 1 5 1 0 0 1 5A, 5B 0 1 0 1 1 6 1 0 1 1 6A, 6B 0 1 1 0 1 7 1 1 0 1 7A, 7B 0 1 1 1 1 8 1 1 1 1 8A, 8B 1 0 0 0 1 9 1 0 0 1 1 10 1 0 1 0 1 11 1 0 1 1 1 12 1 1 0 0 1 13 1 1 0 1 1 14 1 1 1 0 1 15 1 1 1 1 1 16 Logic “0” = VAL , VENL ≤ 0.8V, Logic “1” = VAH , VENH ≥ 2.4V. Logic “0” = VAL , VENL ≤ 0.8V, Logic “1” = VAH , VENH ≥ 2.4V. DG509A A1 A0 EN ON SWITCHES X X 0 None 0 0 1 1A, 1B 0 1 1 2A, 2B 1 0 1 3A, 3B 1 1 1 4A, 4B A 0 , A1 , EN Logic “1” = VAH ≥ 2.4V, Logic “0” = VAL ≤ 0.8V. 2 DG506A, DG507A, DG509A Functional Diagrams DG507A DG506A S1 S1A S2 S2A S3 S3A S4 S4A S5 S5A S6 S6A S7 S7A S8 DA S8A D S9 S1B S10 S2B S11 S3B S12 S4B S13 S5B ADDRESS DECODER 1 OF 16 S14 ENABLE 1 OF 4 S6B S15 DB ADDRESS DECODER 1 OF 8 ENABLE 1 OF 2 S7B S16 A0 A1 A2 A3 S8B EN A0 A1 A2 EN (ENABLE INPUT) 3 Line Binary Address Inputs (0 0 0) and EN = 5V Above example shows channels 1A and 1B turned ON. 4 Line Binary Address Inputs (0 0 0 1) and EN = 5V Above example shows channel 2 turned ON. DG509A S1A S2A S3A DA S4A S1B DB S2B S3B S4B 2 Line Binary Address Inputs (0 0) and EN = 1 Above example shows channels 1A and 1B turned ON. Schematic Diagram V+ LOGIC TRIP POINT REF DECODER + - V+ SX AX GND DX LOGIC A X INPUT OR EN VLOGIC INTERFACE AND LEVEL SHIFTER 3 TYPICAL SWITCH DG506A, DG507A, DG509A Absolute Maximum Ratings Thermal Information V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V Digital Inputs, VS, VD (Note 1). . . . . . . . . . . . . (V- -2V) To (V+ +2V) Continuous Current, (Any Terminal Except S or D) . . . . . . . . . 30mA Continuous Current, (S or D) . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 40mA Thermal Resistance (Typical, Note 2) Operating Conditions Temperature Range “A” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC “B” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25oC to 85oC “C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC θJA ( oC/W) θJC (oC/W) 28 Ld CERDIP Package. . . . . . . . . . . . 55 18 16 Ld PDIP Package . . . . . . . . . . . . . . 90 N/A 28 Ld PDIP Package . . . . . . . . . . . . . . 55 N/A 16 Ld SOIC Package . . . . . . . . . . . . . . 100 N/A 28 Ld SOIC Package . . . . . . . . . . . . . . 70 N/A Maximum Junction Temperature CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175oC PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature “A” and “B” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . -65oC to 150oC “C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65oC to 125oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on SX , D X, EN, or AX exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings. 2. θJA is measured with the component mounted on an evaluation PC board in free air. TA = 25oC, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V, Unless Otherwise Specified Electrical Specifications “A” SUFFIX PARAMETER TEST CONDITIONS “B” AND “C” SUFFIX (NOTE 4) (NOTE 3) (NOTE 4) (NOTE 4) (NOTE 3) (NOTE 4) MIN TYP MAX MIN TYP MAX UNITS DYNAMIC CHARACTERISTICS Switching Time of Multiplexer, tTRANSITION See Figure 1 - 0.6 1 - 0.6 - µs Break-Before-Make Interval, tOPEN See Figure 3 - 0.2 - - 0.2 - µs Enable Turn-ON Time, tON(EN) See Figure 2 - 1 1.5 - 1 - µs Enable Turn-OFF Time, tOFF(EN) See Figure 2 - 0.4 1.0 - 0.4 - µs OFF Isolation, OIRR VEN = 0V, RL = 1kΩ, C L = 15pF, VS = 7VRMS , f = 500kHz (Note 5) - 68 - - 68 - dB Source OFF Capacitance, CS(OFF) VS = 0V, VEN = 0V, f = 140kHz DG506A, DG507A - 6 - - 6 - pF DG509A - 5 - - 5 - pF DG506A - 45 - - 45 - pF DG507A - 23 - - 23 - pF DG509A - 12 - - 12 - pF Drain OFF Capacitance, CD(OFF) Charge Injection, Q VD = 0V, VEN = 0V, f = 140kHz See Figure 4 DG506A, DG507A - 6 - - 6 - pC DG509A - 4 - - 4 - pC DIGITAL INPUT CHARACTERISTICS Address Input Current, Input Voltage High, IAH VA = 2.4V -10 -0.002 - -10 -0.002 - µA VA = 15V - 0.006 10 - 0.006 10 µA Address Input Current Input Voltage Low, IAL VEN = 2.4V -10 -0.002 - -10 -0.002 - µA -10 -0.002 - -10 -0.0002 - µA VEN = 0V 4 VA = 0V DG506A, DG507A, DG509A TA = 25oC, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V, Unless Otherwise Specified (Continued) Electrical Specifications “A” SUFFIX PARAMETER TEST CONDITIONS “B” AND “C” SUFFIX (NOTE 4) (NOTE 3) (NOTE 4) (NOTE 4) (NOTE 3) (NOTE 4) MIN TYP MAX MIN TYP MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG (Note 7) -15 - +15 -15 Drain-Source ON Resistance, rDS(ON) Sequence Each IS = -200µA, VD = +10V Switch ON IS = -200µA, VD = -10V VAL = 0.8V VAH = 2.4V - 270 400 - - 230 400 - rDS(ON) Matching Between Channels -10V ≤ VS ≤ +10V - 6 - - Source OFF Leakage Current, IS(OFF) VEN = 0V VS = +10V, VD = -10V -1 0.002 1 VS = -10V, VD = +10V -1 -0.005 1 Drain OFF Leakage Current, ID(OFF) VEN = 0V - +15 V 270 450 Ω 230 450 Ω 6 - % -5 0.002 5 nA -5 -0.005 5 nA r DS(ON)MAX – r DS ( ON )MI N ∆r D S ( ON ) = ----------------------------------------------------------------------r DS ( ON )AVG DG506A DG507A DG509A VS = -10V, VD = +10V -10 0.02 10 -20 0.02 20 nA VS = +10V, VD = -10V -10 -0.03 10 -20 -0.03 20 nA VS = -10V, VD = +10V -5 0.007 5 -10 0.007 10 nA VS = +10V, VD = -10V -5 -0.015 5 -10 -0.015 10 nA VS = -10V, VD = +10V - 0.005 10 - 0.005 20 nA VS = +10V, VD = -10V -10 -0.008 - -20 -0.008 - nA Drain ON Leakage Current, (Note 6) Sequence Each ID(ON) Switch ON DG506A VD = VS(ALL) = +10V VAL = 0.8V VD = VS(ALL) = -10V VAH = 2.4V DG507A VD = VS(ALL) = +10V -10 0.03 10 -20 0.03 20 nA -10 -0.06 10 -20 -0.06 20 nA -5 0.015 5 -10 0.015 10 nA VD = VS(ALL) = -10V -5 -0.03 5 -10 -0.03 10 nA VD = VS(ALL) = +10V - 0.007 10 - 0.007 20 nA VD = VS(ALL) = -10V -10 -0.015 - -20 -0.015 - nA - 1.3 2.4 - 1.3 2.4 mA -1.5 -0.7 - -1.5 -0.7 - mA - 1.3 2.4 - 1.3 2.4 mA -1.5 -0.7 - -1.5 -0.7 - mA DG509A POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ VEN = 5.0V, VA = 0V (Enabled) Negative Supply Current, IPositive Supply Current, I+ Standby VEN = 0V, VA = 0V (Standby) Negative Supply Current, I- Standby 5 DG506A, DG507A, DG509A Electrical Specifications TA = Over Operating Temperature Range, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V, Unless Otherwise Specified “A” SUFFIX PARAMETER TEST CONDITIONS MIN (NOTE 3) TYP -30 - “B” AND “C” SUFFIX MAX MIN (NOTE 3) TYP MAX UNITS - - - - - µA - 30 - - - µA DIGITAL INPUT CHARACTERISTICS Address Input Current, Input VA = 2.4V Voltage High, IAH VA = 15V Address Input Current Input Voltage Low, IAL VEN = 2.4V VA = 0V VEN = 0V -30 - - - - - µA -30 - - - - - µA -15 - +15 - - - V ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG (Note 7) Drain-Source ON Resistance, rDS(ON) Sequence Each Switch ON VAL = 0.8V VAH = 2.4V IS = -200µA, VD = +10V - - 500 - - - Ω IS = -200µA, VD = -10V - - 500 - - - Ω Source OFF Leakage Current, IS(OFF) VEN = 0V VS = +10V, VD = -10V - - 50 - - - nA VS = -10V, VD = +10V -50 - - - - - nA VS = -10V, VD = +10V - - 300 - - - nA VS = +10V, VD = -10V -300 - - - - - nA VS = -10V, VD = +10V - - 200 - - - nA VS = +10V, VD = -10V -200 - - - - - nA Drain OFF Leakage Current, VEN = 0V ID(OFF) DG506A DG507A DG509A Drain ON Leakage Current, ID(ON) DG506A (Note 6) Sequence Each Switch ON VAL = 0.8V VAH = 2.4V DG507A DG509A VS = -10V, VD = +10V - - 100 - - - nA VS = +10V, VD = -10V -100 - - - - - nA VD = VS(ALL) = +10V - - 300 - - - nA VD = VS(ALL) = -10V -300 - - - - - nA VD = VS(ALL) = +10V - - 200 - - - nA VD = VS(ALL) = -10V -200 - - - - - nA VD = VS(ALL) = +10V - - 100 - - - nA VD = VS(ALL) = -10V -100 - - - - - nA VEN = 5.0V, VA = 0V -3.2 - 4.5 - - - mA -3.2 - 4.5 - - - mA -3.2 - 4.5 - - - mA -3.2 - 4.5 - - - mA POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ Negative Supply Current, IPositive Standby Supply Current, I+ VEN = 0V, VA = 0V Negative Standby Supply Current, INOTES: 3. Typical values are for design aid only, not guaranteed and not subject to production testing. 4. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. 5. Off isolation = 20Log |VS | /|VD |, where VS = input to Off switch, and VD = output due to VS . 6. ID(ON) is leakage from driver into “ON” switch. 7. Parameter not tested. Parameter guaranteed by design or characterization. 6 DG506A, DG507A, DG509A Test Circuits and Waveforms +15V +2.4V +15V +2.4V V+ V+ EN DG506A A3 EN +10V S1 S1A THRU S8A , DA A2 S2B , AND S7B S2 THRU S15 A2 S16 A1 A0 LOGIC INPUT -10V GND V1MΩ S8B A1 SWITCH OUTPUT VO D 50Ω +10V DG507A S1B (NOTE) LOGIC INPUT A0 DB GND V- SWITCH OUTPUT VO 1MΩ 50Ω 35pF -10V 35pF -15V -15V NOTE: Similar connections for DG509A. FIGURE 1A. DG506A TEST CIRCUIT FIGURE 1B. DG507A TEST CIRCUIT 3V LOGIC INPUT tr < 20ns tf < 20ns 50% 0 VS1 S1 ON 0.8VS1 SWITCH OUTPUT VO 0 0.8VS8 VS8 S8 ON TRANSITION TIME TRANSITION TIME FIGURE 1C. MEASUREMENT POINTS FIGURE 1. SWITCHING TIME +15V +15V V+ V+ EN S1 -5V EN S2 THRU S16 A2 A0 A1 50Ω S1A THRU S8A , DA , S2B THRU S8B A1 A0 EN -5V DG507A (NOTE) DG506A A3 S1B SWITCH OUTPUT VO D GND V- A2 EN 1kΩ -15V FIGURE 2A. DG506A TEST CIRCUIT 35pF 50Ω GND SWITCH OUTPUT VO DB V- 1kΩ -15V NOTE: Similar connections for DG509A. FIGURE 2B. DG507A TEST CIRCUIT 7 35pF DG506A, DG507A, DG509A Test Circuits and Waveforms (Continued) tr < 20ns tf < 20ns 50% 3V 50% EN 0V tON (EN) tOFF (EN) 0V 0.1VO SWITCH OUTPUT VO 0.9VO VO FIGURE 2C. MEASUREMENT POINTS FIGURE 2. ENABLE TIMES +15V +2.4V V+ EN A0 +5V (VS) ALL S AND DA tr < 20ns tf < 20ns 3V LOGIC INPUT DG506A DG507A (NOTE) 0V A1 VS A2 A3 LOGIC INPUT SWITCH OUTPUT VO DB GND SWITCH OUTPUT VO V- 50Ω 50% 50% 0V 1kΩ 35pF tOPEN -15V NOTE: Similar connections for DG509A. FIGURE 3B. MEASUREMENT POINTS FIGURE 3A. TEST CIRCUIT FIGURE 3. BREAK-BEFORE-MAKE INTERVAL +15V +15V V+ V+ EN EN DG506A A3 DG507A (NOTE) S1 A2 A2 A1 A1 A0 LOGIC INPUT D GND VO V- A0 LOGIC INPUT GND S1A, S1B DA OR DB 1000pF -15V . FIGURE 4A. DG506A TEST CIRCUIT 8 VO V1000pF -15V NOTE: Similar connections for DG509A. FIGURE 4B. DG507A TEST CIRCUIT DG506A, DG507A, DG509A Test Circuits and Waveforms (Continued) 3V EN 0 ∆VO VO ∆VO is the measured voltage error due to charge injection. The charge transfer error in Coulombs is Q = C L x ∆VO . FIGURE 4C. CHARGE INJECTION WAVEFORMS FIGURE 4. CHARGE INJECTION Typical Performance Curves 400 550 V+ = +15V V- = -15V VEN = 2.4V IO = -200µA +10V SIGNALS 300 350 rDS(ON) (Ω) rDS(ON) (Ω) V+ = +15V, V- = -15V 500 V+ = +10V, V- = -10V 450 V+ = +12V, V- = -12V V+ = +7.5V, V- = -7.5V 400 300 250 -10V SIGNALS 200 200 150 100 100 50 0 -15 -10 -5 0 5 10 ANALOG SIGNAL VOLTAGE (V) FIGURE 5. rDS(ON) vs ANALOG SIGNAL VOLTAGE vs SUPPLY VOLTAGE 9 15 0 -55 -25 0 20 45 70 100 125 TEMPERATURE (oC) FIGURE 6. TYPICAL rDS(ON) VARIATION WITH TEMPERATURE DG506A, DG507A, DG509A Die Characteristics DIE DIMENSIONS: PASSIVATION: 3810µm x 2770µm Type: PSG/Nitride Thickness: PSG: 7kÅ ±1.4kÅ Nitride: 8kÅ ±1.2kÅ METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm 2 Metallization Mask Layout DG506A NC NC V+ D V- S16 S8 S15 S7 S14 S6 S13 S5 S12 S4 S11 S3 S10 S2 S9 S1 GND 10 NC A3 A2 A1 A0 EN DG506A, DG507A, DG509A Die Characteristics DIE DIMENSIONS: PASSIVATION: 3810µm x 2770µm Type: PSG/Nitride Thickness: PSG: 7kÅ ±1.4kÅ Nitride: 8kÅ ±1.2kÅ METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm 2 Metallization Mask Layout DG507A NC DB V+ DA V- S8B S8A S7B S7A S6B S6A S5B S5A S4B S4A S3B S3A S2B S2A S1B S1A GND 11 NC NC A2 A1 A0 EN DG506A, DG507A, DG509A Die Characteristics DIE DIMENSIONS: PASSIVATION: 3100µm x 2083µm Type: PSG/Nitride Thickness: PSG: 7kÅ ±1.4kÅ Nitride: 8kÅ ±1.2kÅ METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm 2 Metallization Mask Layout DG509A EN A0 A1 GND V+ VS1B S1A S2B S2A S3B S3A S4B S4A 12 DA DB DG506A, DG507A, DG509A Dual-In-Line Plastic Packages (PDIP) E16.3 (JEDEC MS-001-BB ISSUE D) 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE N E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AD E BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8, 10 eA C 0.008 0.014 C D 0.735 0.775 18.66 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 0.005 - 0.13 - 5 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC eA 0.300 BSC eB - 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. L 0.115 N 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 13 5 E 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 0.355 19.68 D1 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 0.204 16 2.54 BSC 7.62 BSC 0.430 - 0.150 2.93 10.92 3.81 16 6 7 4 9 Rev. 0 12/93 DG506A, DG507A, DG509A Dual-In-Line Plastic Packages (PDIP) E28.6 (JEDEC MS-001-BF ISSUE D) 28 LEAD NARROW BODY DUAL-IN-LINE PLASTIC PACKAGE N E1 INDEX AREA 1 2 3 N/2 INCHES -B- -AE D BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 eA A1 eC B C L 0.010 (0.25) M C A B S C eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.250 - 6.35 4 A1 0.015 - 0.39 - 4 A2 0.125 0.195 3.18 4.95 - B 0.014 0.022 0.356 0.558 - B1 0.030 0.070 0.77 1.77 8 C 0.008 0.015 D 1.380 1.565 0.204 0.381 35.1 - 39.7 5 - 5 D1 0.005 - 0.13 E 0.600 0.625 15.24 15.87 6 E1 0.485 0.580 12.32 14.73 5 e 0.100 BSC 2.54 BSC - 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. eA 0.600 BSC 15.24 BSC 6 eB - 0.700 - 7 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. L 0.115 0.200 2.93 N 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 14 28 17.78 5.08 28 4 9 Rev. 0 12/93 DG506A, DG507A, DG509A Small Outline Plastic Packages (SOIC) N M16.3 (JEDEC MS-013-AA ISSUE C) INDEX AREA 0.25(0.010) M H B M 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE E INCHES -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- µα e A1 B 0.25(0.010) M 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.3977 0.4133 10.10 10.50 3 E 0.2914 0.2992 7.40 7.60 4 e C B S 0.050 BSC 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 15 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 8o 0o N NOTES: MILLIMETERS SYMBOL α 16 0o 16 7 8o Rev. 0 12/93 DG506A, DG507A, DG509A Small Outline Plastic Packages (SOIC) M28.3 (JEDEC MS-013-AE ISSUE C) N 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E -B1 2 3 L SEATING PLANE -A- h x 45o A D µα e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.6969 0.7125 17.70 18.10 3 E 0.2914 0.2992 7.40 7.60 4 e -C- B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 16 0.05 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.01 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 8o 0o N α NOTES: MILLIMETERS SYMBOL 28 0o 28 7 8o Rev. 0 12/93 DG506A, DG507A, DG509A Ceramic Dual-In-Line Frit Seal Packages (CERDIP) F28.6 MIL-STD-1835 GDIP1-T28 (D-10, CONFIGURATION A) 28 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE LEAD FINISH c1 -D- -A- BASE METAL E M -Bbbb S C A-B S -C- S1 0.232 - 5.92 - 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - eA e ccc M C A - B S eA/2 c aaa M C A - B S D S D S NOTES - b2 b MAX 0.014 α A A MIN b A L MAX A Q SEATING PLANE MILLIMETERS MIN M (b) D BASE PLANE SYMBOL b1 SECTION A-A D S INCHES (c) NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 1.490 - 37.85 5 E 0.500 0.610 15.49 5 12.70 e 0.100 BSC 2.54 BSC - eA 0.600 BSC 15.24 BSC - eA/2 0.300 BSC 7.62 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 6 S1 0.005 - 0.13 - 7 105o 90o 105o - 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. α 90o aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. N 28 28 8 Rev. 0 4/94 5. This dimension allows for off-center lid, meniscus, and glass overrun. 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at website www.intersil.com/design/quality/iso.asp Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 NORTH AMERICA Intersil Corporation 2401 Palm Bay Rd. Palm Bay, FL 32905 TEL: (321) 724-7000 FAX: (321) 724-7240 17 ASIA Intersil Ltd. 8F-2, 96, Sec. 1, Chien-kuo North, Taipei, Taiwan 104 Republic of China TEL: 886-2-2515-8508 FAX: 886-2-2515-8369