DG308A Data Sheet November 1999 Quad Monolithic SPST, CMOS Analog Switch The DG308A quad monolithic SPST, CMOS switch is latch proof and is designed to block signals up to 30VP-P when OFF. Featuring low ON resistance, low power consumption, and rail-to-rail analog signal range, this switch is ideally suited for high speed switching applications in communications, instrumentation and process control. The DG308A has single and dual supply capability. The input thresholds are CMOS compatible. File Number 3120.3 Features • Low Power Consumption • CMOS Compatible • ±15V Analog Signal Range • Single or Dual Supply Capability • Alternate Source Functional Diagram DG308A Ordering Information PART NUMBER S1 TEMP. RANGE (oC) PACKAGE PKG. NO. DG308ACJ 0 to 70 16 Ld PDIP E16.3 DG308ACY 0 to 70 16 Ld SOIC M16.15 IN1 D1 S2 IN2 D2 Pinout S3 DG308A (PDIP, SOIC) TOP VIEW IN3 D3 S4 IN1 1 16 IN2 D1 2 15 D2 S1 3 V- 4 GND 5 14 S2 13 V+ (SUBSTRATE) 12 NC S4 6 11 S3 D4 7 10 D3 IN4 8 9 IN3 - IN4 D4 SWITCHES SHOWN FOR LOGIC “1” INPUT TRUTH TABLE LOGIC DG308A 0 OFF 1 ON Logic “0” ≤3.5V, Logic “1” ≥ 11V at V+ = 15V. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 DG308A Schematic Diagram (One Channel) DG308A V+ P1 P2 P3 S P4 P5 P6 P7 VIN N9 N8 P8 N1 N2 N3 N6 GND N7 N11 D N4 V- 2 N5 N10 DG308A Absolute Maximum Ratings Thermal Information V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V Digital Inputs, VS, VD (Note 1) . . . . . . . . . . . . . . (V-) -2V to (V+) +2V or 30mA, Whichever Comes First Continuous Current, (Any Terminal Except S) . . . . . . . . . . . . . 30mA Continuous Current, (S or D) . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 70mA Thermal Resistance (Typical, Note 2) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . . 65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range “C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on SX , DX , or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. θJA is measured with the component mounted on an evaluation PC board in free air. V+ = 15V, V- = -15V, GND = 0V, TA = 25oC Electrical Specifications PARAMETER TEST CONDITIONS (NOTE 4) MIN (NOTE 3) TYP (NOTE 4) MAX UNITS DYNAMIC CHARACTERISTICS Turn-ON Time, tON See Figure 1 - 130 200 ns Turn-OFF Time, tOFF See Figure 1 - 90 150 ns Charge Injection, Q CL = 1µF, RS = 0, VS = 0V - -10 - pC OFF Isolation, OIRR VIN = 0V, RL = 75Ω, VS = 2VP-P , f = 500kHz (Note 5) - 78 - dB Source OFF Capacitance, CS(OFF) f = 140kHz VS = 0V VIN = 0V - 11 - pF Drain OFF Capacitance, CD(OFF) VD = 0V VIN = 0V - 8 - pF Channel ON Capacitance, CD(ON) + CS(ON) VS = VD = 0V VIN = 15V - 27 - pF DIGITAL INPUT CHARACTERISTICS Input Current with Voltage High, IIH VIN = 15V, Full Temperature Range - 0.001 1 µA Input Current with Voltage Low, IIL VIN = 0V, Full Temperature Range -1 -0.001 - µA -15 - 15 V IS = -1mA, VD = +10V - 60 100 Ω IS = 1mA, VD = -10V - 60 100 Ω VS = 14V, VD = -14V - 0.1 5 nA VS = -14V, VD = 14V -5 -0.1 - nA VS = -14V, VD = 14V - 0.1 5 nA VS = 14V, VD = -14V -5 -0.1 - nA VD = VS = 14V - 0.1 5 nA VD = VS = -14V -5 -0.1 - nA ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG Drain-Source ON Resistance, rDS(ON) VIN = 11V Source OFF Leakage Current, IS(OFF) VIN = 3.5V Drain OFF Leakage Current, ID(OFF) Channel ON Leakage Current, ID(ON) 3 VIN = 11V DG308A V+ = 15V, V- = -15V, GND = 0V, TA = 25oC (Continued) Electrical Specifications PARAMETER TEST CONDITIONS (NOTE 4) MIN (NOTE 3) TYP (NOTE 4) MAX UNITS - 0.001 100 µA -100 -0.001 - µA POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ All Channels ON or OFF VIN = 0V or 15V Negative Supply Current, INOTES: 3. Typical values are for design aid only, not guaranteed and not subject to production testing. 4. The algebraic convention whereby the most negative value is a minimum, and the most positive is a maximum, is used in this data sheet. 5. OFF isolation = 20 Log VD /VS , where VS = input to OFF switch, and VD = output. Test Circuit and Waveforms VO = VS 15V RL LOGIC “1” = SWITCH ON RL + rDS(ON) LOGIC INPUT tr < 20ns tf < 20ns 0V V+ S D 15V 50% 50% VO VS = 3V RL 1kΩ IN CL 35pF SWITCH INPUT 90% 90% SWITCH OUTPUT 0V GND V-15V tON FIGURE 1. tON AND tOFF TEST CIRCUIT AND MEASUREMENT POINTS 4 tOFF DG308A Die Characteristics DIE DIMENSIONS: PASSIVATION: 2058µm x 2109µm Type: PSG Over Nitride PSG Thickness: 7kÅ ±1.4kÅ Nitride Thickness:8kÅ ±1.2kÅ METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm2 Metallization Mask Layout DG308A PIN 14 S2 PIN 13 V+ (SUBSTRATE) PIN 11 S3 PIN 15 D2 PIN 10 D3 PIN 16 IN2 PIN 9 IN3 PIN 1 D1 PIN 8 IN4 PIN 2 IN1 PIN 7 D4 PIN 3 S1 5 PIN 4 V- PIN 5 GND PIN 6 54 DG308A Dual-In-Line Plastic Packages (PDIP) N E16.3 (JEDEC MS-001-BB ISSUE D) E1 INDEX AREA 1 2 3 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE N/2 INCHES -B- SYMBOL -AD E BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 eA A1 eC B 0.010 (0.25) M C L C A B S C eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 6 MILLIMETERS MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - B1 0.045 0.070 1.15 1.77 8, 10 C 0.008 0.014 0.204 0.355 - D 0.735 0.775 18.66 19.68 5 D1 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC 6 eB - 0.430 - 10.92 7 L 0.115 0.150 2.93 3.81 4 N 16 16 9 Rev. 0 12/93 DG308A Small Outline Plastic Packages (SOIC) N INDEX AREA H 0.25(0.010) M M16.15 (JEDEC MS-012-AC ISSUE C) B M 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE E -B1 2 INCHES 3 L SEATING PLANE -A- h x 45o A D -C- e α A1 B 0.25(0.010) M C 0.10(0.004) C A M B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 N α 16 0o 1.27 6 16 8o 0o 7 8o Rev. 0 12/93 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 7 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029